Search Documents

By Tong Zhilin

The reasons why the pits were formed on the cathode in the process of Ni electrowinning and the methods how to prevent these pits from forming are described. Some examples are presented. It has 'been proven that P507 and P204 present in the electrolyte can effectively prevent pits from forming on the cathode.

Jan 1, 1993

By P. Tapp, T. Evans, N. A. Molloy, J. Lucas

"Consideration of the protoype tuyere geometry for injection of inert gas through the bottom in a basic oxygen steel furnace and a requirement to specify an optimal flow for bottom wear and metal penetration led to experimental investigations[l,2] to apply the results of previous workers to this specific case, Flow velocity profile development within the tuyere was proposed as significant and the experimental scheme was designed to test this. It is proposed that the design criterion for the conditions of optimal flow of the prototype geometry be based on the non-dimensional mass velocity.INTRODUCTIONSharma[3] tested small diameter tuyeres in a laboratory hot model using molten iron to define a flow criterion for prevention of penetration of the bath liquid into the tuyere. Using argon, nitrogen and helium through a range of tuyeres (1 to 3 mm ill ) he proposed the jet Froude number C Fr' ) with the critical value being 2400 - 2500 or higher. Sonic or supersonic velocity was not a sufficient criterion. The tuyere design was a parallel tubular duct of moderate aspect ratio CAR) i.e. the ratio of length to diameter ranging from about 22 to 36 in the experimental furnace.Farmer et al[4] stated their their aim ""to develop a unifying explanation and procedure for the proper design of tuyeres"" but disagreed with Sharma's jet Froude number criterion. Recalculating Sharma's data they proposed instead a fully expanded Mach number of 1.75 with an initial expansion angle of ten degrees as the lower bounds of flow to meet the design requirement. They experimented with tuyeres in a water model using tubular, annular and convergent-divergent nozzles. The aspect ratio of the parallel duct tuyeres was from 533 to 762 using diameters of 1.4, 1.7 and 2.0 mm C the diameters being of tubes to be used full scale). Subsequently these results were applied to a prototype tuyere using a diameter of 1.7 mm with beneficial results in practice. This tuyere had an aspect ratio of 1067."

Jan 1, 1996

By Donato Firrao, Giorgio Scavino, Paolo Matteis

"The fatigue behavior of two high-strength sheet steels used to produce car bodies, a dual-phase steel and a TWIP one, both with ultimate tensile strength close to 1 GPa, is investigated.Unnotched tensile specimens are fatigue tested at room temperature with constant load amplitude and zero load ratio, in order to determine their 1 million cycles fatigue limit, both in the asfabricated sheet condition and after the resistance spot welding of one small homologous sheet square onto the calibrated length of the tensile specimen. Moreover, pre-cracked compact tension specimens are tested with load ratio 0.1 to determine the Paris fatigue crack growth curve.The fatigue results are completed with crystallographic, microstructural, tensile, and fractographic examinations, and the influence of the microstructure and of the welding processes is discussed.IntroductionCar bodies are increasingly made with high-strength weldable steels, in order to reduce vehicles' weight (to save fuel and reduce air pollution) and to improve the vehicle occupant safety in case of car crash. The main mechanical requirements of these steels in service are fracture strength and energy absorption, relevant for crashes, as well as fatigue endurance, relevant for ordinary car usage. [1]Steel sheets for car-body applications are usually made by continuous casting, hot rolling, cold rolling, continuous annealing (or other continuous heat treatment), and protective coating (in some cases). The sheets are then cold formed (deep drawn) to produce car body parts. Finally, the car bodies are built by assembling several deep-drawn parts, often consisting of different steels, usually through the Resistance Spot Welding (RSW) process, whereby two or three overlapping sheets are welded by local Joule-effect heating [2].Dual-Phase (DP) steels are widely used, low alloy steels with a microstructure consisting of ferrite and martensite, obtained from a final heat treatment which consists of heating at an intercritical temperature and then quenching. [3,4]"

Jan 1, 2012

By K. Krishnapisharody

A mathematical model has been developed to predict the interface dynamics and droplet generation of the buoyant phase in a two-fluid system. The model employs the well-known SIMPLE algorithm for obtaining flow fields and the Volume of Fluid (VOF) method, for interface tracking. The implementation of the model in water-oil systems, where the oil layer is placed above a recirculating water bath, is discussed. The evolution of the water-oil interface leading to the formation of oil droplets is computed realistically.

Jan 1, 2008

By G. R. Adams, N. Y. Tang, N. Qiang

"Aluminum is the most important alloy addition to Zn baths for controlling the reaction kinetics between the steel substrate and molten Zn in continuous galvanizing operations. Due to the complexity of the Zn-Fe-Al ternary system, the measurement and control of effective bath Al remains a challenge for modem galvanizers. The successful development of Al sensors has made the real-time measurements of bath Al contents possible. To facilitate their application, a computer interface and a palm-size data logger have been developed by Cominco. Plant applications indicated that the sensor possessed sufficient accuracy for process monitoring and control. The working mechanism of the Al sensors and Cominco's development work is described, and the results of sensor applications are presented.IntroductionControl of bath Al content is critical in modem continuous galvanizing because it has a strong influence on coating structure and properties and the overall product quality. The control of effective bath Al content (Al in liquid solution) is particularly critical for galvannealing where a high bath Al content may lead to incomplete alloying during post annealing, and a low bath Al content may result in other operation problems, such as excessive bottom dross accumulation and difficulties in coating thickness control. The desirable accuracy of the Al control is within ±50 ppm of target levels. In principle, such an accuracy is achievable for modem chemical analysis facilities, such as atomic absorption photospectrometer (AAS) and induction-coupled plasma (ICP). However, a recent study carried out by the International Lead and Zinc Research Organization (ILZRO) indicated that such an accuracy is rarely achieved in the zinc and steel industries.(1)"

Jan 1, 1997

By Volovik A. V. Ivtan, Shelkov E. M. Ivtah

"One of the most power consumption Industrial process is production of Al from bauxites (about 45000KWt.hour electrical energy for production of 1 ton. of technical Al). This process is based at the low efficiency and productivity electrolysis technology.Last years IVTAN investigations give to .us information about possibility to use of high temperature shaft- furnaces for efficiency production of alumina (AL2O3 ) technical. aluminium and some all.oys on the base of the high temperature carbon- thermal reduction process. At this case power consumption for production of unit of last, product will be less at the 3-4 times.The carbon-thermal method is allow produce alumina (Al203 ), technical Al and its alloys not only from deficient bauxites, but practically inexhaustible reserve of other types of Al-contain row materials (cianite, sillimonite and so on/The thermal-chemical economical analises of fulfilled at the IVTAN, production of alumina. Base on facts of production and technical technology are especially for ones arguments at the high temperature shaft-furnace technical Al and its alloysIn the last decades of the 20-th century, the discharge into atmosphere of high temperature and. combustion gases places . problems before humanity more and more sharply and becomes of great importance task.But at the same time, as production of material values increases, intensity of pollution of environment increases all time. And the value of new processes and. technologies of material production, aimed at reducing the expenditure of power and pollution of· the environment, also increases."

Jan 1, 2000

By A. S. Block-Bolten

Two innovations in nickel-arsenic separation have been studied on a laboratory scale. The first requires only a nitric acid atmospheric leach without preliminary roasting and leads to favorable final conditions for precipitation of arsenic as highly stable FeAsO4, The second is an NaOH-H2O2 pressure leach which is an alternative to the known NaOH-O2 pressure leach. Either method offers the possibility of rapid and efficient separation of nickel from arsenic and is applicable, for example to the high grade niccolite deposits in the Great Slave Lake area of northern Canada.

Jan 1, 1982

By D. Silva-Galvan, R. D. Morales, S. Gonzáelez-López, A. Romero-Serrano, G. Plascencia-Barrera, F. Chavez-Alcala

This work is focussed on lead decopperising by two techniques: conventional top addition of sulfur and injection of sulfur powder. It is found that the first method proceeds under equilibrium conditions and the second one depends on kinetic considerations. Experiments were carried out using 15 kg lead baths at two temperatures, 340°C and 380°C. The carrying gas used for the injection trials was nitrogen at flow rates of 6.3 and 18.6 L min- 1• The results show that 'decopperising process is more efficient at temperatures close to the melting point of lead for the sulfur top addition process, whereas high temperatures produce better copper removal for the injection of sulfur powder. Besides, the sulfur injection with the higher nitrogen flow rate (18.6 L min-1) produced higher decopperising rates. Thermodynamic and kinetic models are used to simulate this lead refining process.

Jan 1, 2000

By Animesh Jha, Chris Dometakis

"Without the use of a flux, only a poor dispersion of ceramic phase can be achieved. A molten-flux-assisted ceramic phase dispersion technique for producing aluminium alloy metalmatrix composites has been developed. In this paper, we report the physical chemistry for the dispersion of TiB2 in molten aluminium. In particular, aspects of the interfacial energy and the thermodynamics of the dispersion reactions are briefly discussed for enhancing the volume of dispersion phase in the molten metal and for controlling their morphology. This investigation also addresses the role of molten flux in the fabrication of AI-alloy mmc using a casting technique. The morphological aspects of the dispersion are explained on the basis of the classical theory· of nucleation.IntroductionMetal matrix composites (MMCs), have long been recognised as an important class of material due to their greater wear resistance, specific stiffness and temperature capability when compared to conventional monolithic alloys. Particulate reinforced composites produced by melt casting techniques have been amongst the first MMCs to achieve commercial market viability. The advent of melt mixing techniques such as the Duralcan™ process have enabled low cost, easily fabricated composites based on the AI-SiC and AIAlz0 3 systems to be produced. In this process, uncoated ceramic particles with diameters 10ltm and larger, are incorporated into conventional monolithic alloys with reinforcement levels up to 25 volume percent. The AI-7Si-SiC metal-matrix composites have good wear resistance, high strength, low density and high thermal conductivity. The combination of these physical and mechanical properties has become a major attraction for the fabrication of light-alloy composite disc rotor brakes for the automotive sector2. However, in silicon-free alloys, SiC is thermodynamically unstable above the composite melting point and is extensively attacked by the melt to form aluminium carbide3 :"

Jan 1, 1996

By J. Szekely, S. Rhee

"A mathematical formulation has been presented to describe heat and fluid flow phenomena in CVD operations. In the statement of the problem, which included consideration of plasma enhanced CVD systems, emphasis was placed on identifying the parameters which play a key role in determining the rate and the spatial uniformity of the deposition process. This was done both through the appropriate dimensionless groups and by presenting an extensive set of computed results. The main conclusions that may be drawn from this work are that the deposition rate will be inherently non-uniform for atmospheric CVD systems; this may be somewhat ameliorated by inclining the susceptor or changing the vessel contours. Operation at greatly redeced pressures and for PECVD systems will give a much more spatially uniform deposition rate.1. INTRODUCTIONIn recent years, there has been a growing interest in chemical vapor deposition techniques for the preparation of thin films for semiconductor, photovoltaic applications and for coatings in general, as evidenced by numerous journal articles and symposium proceedings devoted to this topic (1-6). An interesting variant of this technique is to perform the deposition in a plasma or glow discharge at low pressures because this technology obviates the need for the thermal decomposition of the precursor at the substrate surface and permits operation at greatly reduced temperatures (7-10).By far, the largest portion of the reported work dealing with both these aspects of the technology has been concerned with the characterization of the deposit, quite properly so. However, in more recent times it has been realized that the transport aspects of these processes are also deserving of attention because the understanding of heat flow, fluid flow and diffusional phenomena may provide the key to the solution of problems associated with obtaining uniform deposits and the proper scaling of laboratory measurements in order to design industrial CVD systems."

Jan 1, 1986

By Katja Reinharter

Arsenic can be found in different sulfidic copper concentrates and residues, which for several years have commonly been used in copper metallurgy, as the “arsenic-free” resources are getting rare. Due to the high toxicity the removal of arsenic in the copper smelting process is a very important topic. The typical chemical slag and sulfur attack on the refractory material is getting enhanced by the presence of arsenic. This work deals with post-mortem investigations of a magnesia-chromite brick and castable used in copper smelting furnaces showing an additional and increased chemical attack by arsenic. The knowledge on the wear behaviour is not only based on a detailed chemical and mineralogical characterization, but also on thermochemical FactSageTM calculations, which are carried out on provided post-mortem samples. Post-mortem investigations on used refractory materials represent an important prerequisite for the product development, as well as for special engineered lining concepts to support our customers.

By Selvin Yesilay, Guray Kaya, Bekir Karasu, Asli Cakir

"In this investigation, the wastes of Eti Maden Kirka Boron Company of Turkiye were evaluated in the production of diopside and anorthite-based glass-ceramic glazes suitable for porcelain tiles fast and single-fired under industrial conditions. First of all, high wear resistant frits were produced with the use of concentrator and derivative borax wastes. Second of all, pre-engobed porcelain tile bodies were coated with the standard and newly produced frit-based glazes and industrial fast single-firing was employed. Final products were undergone to the certain standard tests to determine their Vickers hardness, wear resistance, thermal expansion coefficient values, gloss and coloring parameters. The micro-structures and phase formations of the fired glazes were also studied. Consequently, it was confirmed that the utilization of borax solid wastes in fast single-fired porcelain tile glass-ceramic glazes is possible. Introduction Porcelain tiles were introduced at the end of 1980s by Friandre, one of the leading Italian porcelain manufacturers. The American National Standard Specifications for Ceramic Tile defines porcelain tiles as: dense, smooth, impervious (with water absorption value less than 0.5 %) and stain resistant [1]. The excellent technical performances for ceramic tiles, such as mechanical, wear, frost and chemical resistance that make their use possible in indoor and outdoor building applications [2-3]. In the last decade, the growth rate of the global production of porcelain tiles increased more than those of other ceramic products; in fact, the technical properties of porcelain tile, coupled with even more improved aesthetic appearance, gave it a prominent role on the tile market [2]. Glass-ceramics are composed materials of one or more crystalline phases immersed in a residual glassy phase [4-5]. Glass-ceramic technology is based on controlled nucleation and crystallization of bulk glass [6]. The concepts of controlled crystallization of glass designate the separation of a crystalline phase from the parent glass in the form of tiny crystals. Their growth rate and final size are controlled by a suitable heat treatment [7]."

Jan 1, 2008

By Nathan A. Tiner

Sulfuric acid anodizing process is extensively used in many industrial and consumer products to provide corrosion resistance to aluminum alloys. The anodic coatings produced consist of amorphous alhnum oxide with a pornus structure which is easily sealed and colored with dyes. The coatings may contain defects due to surface flaws, canposition and microstructure of the aluminum alloy, and/or due to the anodizing process conditions. This paper will describe the techniques used in anodizing process, various defects which may be produced in anodic coatings and the methods to control them.

Jan 1, 1992

By Che Xin, Liu Tianlong, Bi Hongyun, Chen Lijia

"High-cycle fatigue experiments were conducted at 800°C in laboratory air for three ferrite stainless steels including 15CrNbTi, 15CrMoNbTi and 18CrNbTi, where the stress ratio of 0.l was adopted. The experimental results show that at 800°C, the fatigue limit of the 15CrMoNbTi steel is the highest, the fatigue limit of the 15CrNbTi steel is slightly lower than that of the 15CrMoNbTi steel, and the fatigue limit of the 18CrNbTi steel is the lowest. At the same maximum stress, the 15CrMoNbTi steel has longer fatigue lives than the 15CrNbTi steel in the low stress area, while the 18CrNbTi steel has the shortest fatigue life. In addition, the observations on the fracture surfaces of fatigue specimens reveal that the fatigue cracks initiate transgranularly at the free surface of the specimens and propagate in a transgranular mode.IntroductionIn modem automotive industry, the manufacturers have paid great efforts to clean exhaust gas and to improve fuel economy. It is thought an effective way to increase the temperature of combustion chamber in automotive engine. And thus, the manifold closed to the engine in automotive exhaust system can suffer high temperature up to approximately 1000°C. Because of their relatively low thermal expansion coefficient, high yield strength at elevated temperature and good fatigue resistance, ferrite stainless steels, especially added with alloying elements such as Mo, Nb and Ti, are increasingly used for automotive exhaust systems [1-3]. In fact, exhaust manifold operated under high frequency vibration and exposed to high temperature exhausting gas also requires good fatigue resistance at elevated temperature. Some studies on the high temperature fatigue characteristics of stainless steel have been documented. It has beeen found that the fatigue limit of four ferrite stainless steels including 409L, 436L, 429EM and 444 (18Cr- 2Mo) reduces significantly with increasing temperature [4, 5]. In the research concerning the effect of a-phase embrittlement on fatigue behavior in a high-chromium ferrite stainless steel, it is noted that the precipitation of brittle a-phase will reduce the crack initiation and growth resistances and result in a decrease in fatigue limit [6]. In this investigation, the high-cycle fatigue behavior of three ferrite stainless steels including 18CrNbTi, 15CrNbTi and 15CrMoNbTi at 800°C have been studied to address the mechanical aspect of high-cycle fatigue behavior for ferrite stainless steels and to provide the theoretical reference for the safe design of automotive exhaust system."

Jan 1, 2013

By Chen L. Lin

Scientific visualization is an ideal methodology for investigating complex phenomena that are characterized by large amounts of data. Furthermore, it is invaluable in the study of processes that evolve in time. Scientific visualization relies heavily on computer graphics, image processing and video technologies. Specific applications of scientific visualization in the minerals and materials processing fields that are considered in this paper include: 1) applied CT technology for multiphase materials and minerals, 2) time averaged density profla in air- sparged hydrocyclone (ASH) flotation and 3) dynamic motion analysis of ball mill grinding.

Jan 1, 1993

By Shilai Yuan, Huimin Lu, Zhijiang Gao, Panpan Wang

"Solvent refining of silicon through using Si-Al melts is a valid method to remove the impurities from metallurgical grade silicon (MG-Si) melt. The thermodynamic behavior of impurities Fe, Al, Ca, Ti, Cu, C, B and P in MG-Si during the solidification of MG-Si was studied based on the available thermodynamic parameters and experimental data. The morphology of inclusions was investigated by Scanning Electron Microscope (SEM). The chemical composition of inclusions in MG-Si and Al-Si melt was analyzed by EPMA. It is found that the amount of white inclusion reduces and most impurities are solved into the Al-Si melts. After solidification of Si–Al alloy using induction heating and acid leaching, impurities can be effectively removed. The solidification of silicon from the Si–Al melt is found to be more effective for purification than general silicon solidification.IntroductionPhotovoltaic energy is one of promising energy resources in a sustainable society because of its inexhaustibility and cleanliness. Although the production and installation of solar cells have increased significantly during the last decade, the cost of solar cell installation is still high. Multicrystalline silicon has now become the main material in the photovoltaic market because of its low production cost and because of the relative high conversion efficiency of solar cells made from this material, which has been studied for a long time [1-3].Electronic grade (EG) silicon (99.9999999% Si) is commonly used as the raw material to produce SOG-Si (99.9999% Si). Silicon produced from the chemical routes restricts the development of solar cells due to environment threaten, high energy consumption and low productivity. Purification of metallurgical grade silicon (MG-Si) is a low cost, environment friendly method. Although several metallurgical processes such as directional solidification, vacuum refining and electron beam melting [4], have been developed, the cost reduction and refining efficiencies for manufacturing silicon is still have to be further optimized.In the purification process, it is difficult to remove boron and phosphorus by the conventional metal refining method. The refining efficiency depends on the segregation behavior of different elements in solid silicon and the liquid phase. The segregation ratios of all investigated impurities were found to be much smaller than the segregation coefficients between solid and liquid Al-Si melts [5]. For instance, the segregation coefficient of B in Si is 0.8 at the silicon melting point (1687K), whereas it is around 0.2 when silicon is solidified from Si-Al melt at 1273K. For phosphorus the segregation coefficient is 0.06 when silicon is solidified from Si-Al melt at 973K°C, which is much less than 0.35 for recrystallization from liquid silicon. Since the segregation coefficient of boron in silicon is 0.8, it cannot be removed by directional solidification."

Jan 1, 2014

By G. L. Watt

Fine sized titanium diboride (TiB2) powders have been synthesized in a thermal plasma reactor. Precursor for the synthesis were rutile, boron oxide, and methane. The effect of plasma gas type, precursor ratio, and input power on the synthesis was studied. The produced powders were characterized by X-ray diffraction and chemical analysis. The purified powders were CIP'd, HIP'd, sintered and characterized for porosity, hardness, and microstructure and the results compared with a commercially available TiB2 powder sample.

Jan 1, 1995

By Sepideh Abolghasem, Juan Pablo Casas Rodriguez, Juan Camilo Osorio

Predicting flow stress at high strain-rates is a desirable practice for material behavior characterization. Sub-grain size has shown a huge influence in cutting forces and the workpiece surface finish determination during orthogonal cutting process. Hence, a prediction of flow stress as a function of thermomechanical conditions and sub-grain size is of great important which is studied in this work for OFHC copper. The principal thermomechanical conditions being strain, strain-rate and the accompanying temperature rise are characterized in Plane Strain Machining (PSM) and the resulting microstructure, sub-grain size, is quantified. Material maximum flow stress (a constitutive model) as a function of thermomechanical conditions and sub-grain size is predicted considering a saturated state in microstructure using optimization algorithms for reaching the validated temperature rise based on modified Hahn’s model. Evaluated models suggest a major influence of strain-rate and dislocation in temperature rise estimation and flow stress prediction leading to consideration of mechanical failure phenomenon involved in machining-based manufacturing processes.

Mar 1, 2018

By Rajashekhar Marthi

Lithium is a key component for future electric vehicle batteries and energy storage. The future availability of lithium to meet the growing demands remains in question. Around 60% of lithium resources exist in the form of continental brines. Traditional methods to recover lithium from brines use solar concentration with precipitation and have found limitations in lithium extraction due to interference of Mg in high Mg/Li brines. Thus, there is a need for highly selective adsorbents. Recently, spinel structured delithiated lithium manganese oxides have demonstrated promising results. However, due to the small particle sizes, it is economically difficult to recover the adsorbents and thereby limits industrial applications. In our work, LiMn2O4 ion sieve was synthesized and immobilized on diatomaceous earth. Fundamental adsorption studies were carried out in lithium buffer solutions to understand the nature of adsorption and kinetics. The adsorbents were also tested for recycle stability, as well as recovery of lithium from Great Salt Lake water samples.

By S. P. Song

A computational methodology based on the coupled finite element and boundary methods is developed to predict the free surface shapes of electrically conducting liquids supported by the electromagnetic field. The work is an extension of our previous FEIBE model for induction calculations. The free surface algorithm is developed using the Weighted Residual Method, the very same used for nonlinear finite element formulation. This allows the treatment of field computation and free surface prediction in the same manner, thus making easier the formulation of the magnetically-supported free surface problems. Like other nonlinear algorithms, the boundary/finite element free surface scheme is also iterative owing to the fact that free surface shapes are unknown a priori. But the numerical scheme is robust and efficient and is capable of handling rather complex free surface deformations. Computational algorithms will be given and are tested by comparing with other solutions whenever available. Computed results of magnetically-supported free surface shapes are presented for magnetic levitation under microgravity and floating zone refining processes under normal gravity.

Jan 1, 1996