Search Documents

By Dachun Liu, Wenlong Jiang, Guozheng Zha, Liang Hu

In this paper, a novel technique for recovery of gallium and arsenic by thermal decomposition under vacuum is presented. The effects of distillation tem- perature on the volatilization behavior of each component were investigated. Theoretical calculations and experimental studies have shown that the method is feasible. The results show that under optimum conditions, highly pure Ga can be extractedwithadvantagesoverconventionaltechniques,includingsimpleoperation andenvironmentalfriendliness.Forexample,metallicgallium(purity > 99.99%)is obtained at 1273 K after 3 h under 3–8 Pa. Arsenic is obtained in the form of a elementary substance which could be preserved with relative ease. (cid:1) (cid:1)

Mar 1, 2018

By Fuming Wang, Xin Lu, Hao Bai, Hebin Zhu

"In this study, CO2 emissions and carbon footprint of a typical steel works with integrated process and iron and steel industry in China was calculated and analyzed by a carbon footprint method based on the model of process CO2 emissions in iron and steel making. The carbon footprint of iron and steel industry from 1991 to 2010 in China showed a rapid increasing tendency. In 2008, the CO2 emissions of iron and steel industry in China was 1.289 billion tons, 19.71% of the national total CO2 emissions, and the corresponding carbon footprint was 159.13 million hm2 of green area. Carbon deficit of iron and steel industry also go up gradually if considering the carbon storage by green vegetation. Thus, the internal carbon reduction strategy, such as energy structure optimization and energy saving technology, was mainly encouraged for the sustainable development of iron and steel industry in China.IntroductionThe Global Warming resulting from the increase of Greenhouse Gases (GHGs), in particularly CO2, in the atmosphere has become the main reason of global climate change, and large emission reductions are required for sustainable development [ 1]. The iron and steel industry is the largest energy consuming manufacturing [2] in the world and the largest emitter of CO2 emissions. In 2005, it accounted for about 20% of global industrial energy use and 30% of energy and process CO2 emissions from industry [3]. In China, the crude steel has firmly been ranking at first of the world recent years and kept growing tendency year by year. With the production growth, the CO2 emissions of iron and steel industry also increased significantly and hence the steel industry has become one of the most sources of CO2 emission in China [4], which has attracted more and more attention to seek the carbon reduction strategies.Carbon footprint is an important and useful concept originating from Ecological Footprint, which was used efficiently to quantitatively analyze the impact of the human activities on ecological system, in particularly impact of the human energy activities [5]. In the view of Life Cycle, the carbon footprint is efficient to analyze the direct and indirect CO2 emission in the whole life of various products used in human activities. As to the iron and steel, the important materials and products in the human life, the carbon footprint analysis is quite necessary to evaluate the CO2 emission impact on the corresponding ecological system and global environmental."

Jan 1, 2013

By N. B. Gray, A. E. Guerra, D. E. Morton

"The formation of splash in pyrometallurgical operations that involve the injection of gases into a liquid has been the subject of a number of studies over the last few decades. Given the complexity of the phenomena, there have been some advances in understanding the microscale formation of splash but the ability to accurately predict the amount and character of the splash formed is still in its infancy. First, the macroscale mechanisms for splash formation is very varied. Second, the timescales for splash formation are very small, usually less than 100 milliseconds, making experiments elucidating the formation of splash difficult and costly. Work at the GKW CRC has shown that the microscale mechanism of splash formation is primarily is due to the Kelvin-Helmholtz instability. Substantial progress has been made in understanding the behaviour of large bubbles in effecting splash formation and a simple model has been developed to estimate the behaviour of splash formed from a top submerged lance. Direct numerical computation of splash formation using the GKMAC codes developed at the Centre has been successful in simulating the impact of liquid drops onto a liquid bath.IntroductionInjection of gases into melts is used in the metallurgical industry to promote mixing to ensure acceptable heat and mass transfer rates, conveying solids for alloying, provide efficient contact for gas-melt reactions, and as a reactant. High gas injection rates bring about the formation of splash and slop. Extensive splash formation leads to loss of valuable product, creation of safety hazards, formation of accretion on refractory lining and exhaust ducts, and increased load on dust removal equipment. Many operators and researchers have claimed that splash formation is the limiting factor in many gas injected processes. The problems listed above lead to loss of production and increased maintenance, adding to the cost of processing base metals. Over the last five years, the GKW CRC has been studying the formation of splash from a number of sources. They include the impingment of drops on liquids[ l·2.31, slopping of bath liquidI4.51, breakup of gas bubbles at the liquid-gas interfacel61, shearing of liquids by gases[7·81, and impact of packets of fluids on solidsl81. Theoretically, the extreme deformation of fluid shape and the influence of surface tension makes the simulation of flow resulting from only a drop impacting on a liquid surface a very challenging computational fluid dynamics problem. Recently, we have been successful in simulating the formation of the Rayleigh jet resulting from a drop impact showing the effect of drop Froude number on the shape of the Rayleigh jet."

Jan 1, 1996

By E. Bélisle, Christopher W. Bale, S. Petersen, C. Robelin, K. Hack, J. Melançon, G. Eriksson, A. D. Pelton, P. Chartrand, S. A. Decterov, I. H. Jung, A. Gheribi

The FactSage® package consists of a series of information, database and calculation modules that enable one to access pure substances and solution databases and perform thermochemical equilibrium calculations. FactSage was originally founded by process pyrometallurgists and has since expanded its applications to include hydrometallurgy, electrometallurgy, corrosion, glass technology, combustion, ceramics, geology, environmental studies, etc. With the various modules one can perform a wide variety of thermochemical calculations and generate tables and graphs of complex chemical equilibria and phase diagrams for multicomponent systems. This paper presents examples of recent and current developments in FactSage in areas of particular interest to Dr. David Robertson. These include both ferrous and non-ferrous processing, as well as solidification and refining simulation. The paper also includes reference to the Internet Fact-Web education package.

Jan 1, 2014

By A. Niedbalska

A technique was developed for low pressure diamond synthesis using a specially prepared glassy carbon. The glassy carbon is produced in the form of solid plates by slow carbonization process of phenol formaldehyde resin interrupted at temperatures of 1273° K, 1073° K, and 923° K. The diamond synthesis is performed using cobalt plates as a catalyst-solvent. Synthesis was carried out at applied pressures of 6.0 and 3.8 GPa and a temperature of 1970° K and 2170° K. The products were analyzed by the x-ray powder dyffraction method and by microprobe to identify the diamond crystallites. The samples were taken from the place of contact between the glassy carbon and the cobalt catalyst. They were separated from the charge by a chemical method. Diamonds of the best form and the largest size were obtained at pressures that were much lower than those used in the traditional graphite method of diamond synthesis.

Jan 1, 1989

By Wan Entong, Xie Junlin, Jiann YangHwang, Yang Chengwei, Chen Junfu, Zhang Jianjun, Cao Tongyou, He Feng, Peng Zhugang, Fang De

During the solidification process of peritectic steel (PS), the peritectic reaction often causes volume contraction which associated with surface longitudinal cracks, and using mould flux with low heat flux density help for alleviating surface longitudinal cracks. New peritectic steel mold flux with Co2O3 doping reduced the heat flux density, and the optimal content was found to be 2.0 wt %. Furthermore, basicity and Na2O addition were designed, and the minimum heat flux density required basicity of 1.4 and 10.0 wt %. Na2O content. As a result, the optimal peritectic composition was CaO(35.67wt% ), SiO2(25.48 wt %)，Al2O3(3.7 wt %)， MgO(2.53 wt %)，Na2O(10 wt %)，CaF2(14 wt %)，Co2O3(2 wt %).

Jan 1, 2015

By Lin Li, Wen Shi, Hua Wang

"Specimens of the ultra-low carbon bake hardening steel were soaked for 1 min to 5 min, and then cooled by water quenching. The internal friction experiments were carried out to detect the spectra of the specimens. Results show that Snoek peaks are present in all the specimens, however, an obvious Snoek-Koster peak is found only in the 5 min-annealed specimen. Besides, tensile results indicate that the bake hardening values increase with the annealing time prolonging from 1 min to 3 min, but decrease as the annealing time prolongs further to 5 min. The solute distributions in the specimens were characterized by three dimensional atom probe. Some segregated C and V are found in the 1 min-annealed specimen, and the C and V contents decrease as annealing time prolongs to 5 min.1. IntroductionAs an excellent member of automotive body panel materials, various types of bake hardening (BH) steels have been developed since 1980s. Bake hardening property, as one of the most important mechanical properties, has been studied by many researchers [ 1-5]. As is known, BH phenomenon is generally controlled by the interaction between solute C and dislocations. The Snoek peak of internal friction (IF) is very popular in the investigation of solute C [6-9]. However, result of internal friction cannot suggest the distribution pattern of solute C as well as its influence on BH phenomenon.Three dimensional atom probe (3DAP) can diagnose solute element atoms as well as nano-sized precipitates, and it is the only instrument that currently can identify the identities of individual atoms in a material and measure their spatial coordinates with the resolution close to 0.3 nm [10]. There have been a number of studies about using 3DAP to detect solute elements as well as nanometer sized precipitates [11-19]. For example, Hono et al. [16] used 3DAP to determine the solute elements in an age-hardened Mg-Ca-Zn alloy, and they also obtained the distribution patterns of the observed elements."

Jan 1, 2011

By D. C. Azubike

Wolframite (FeWO4) usually having cassiterite (SnO2) as a major impurity is a primary source of tungsten. Its direct reduction/carburisation with carbon in the temperature range 1000-1400°C, and with hydrogen at 600-900°C followed by carburisation with CO at 900°C are described. Depending on the conditions and reactants employed, Fe, Fe2W, B-Sn,WC, W2C, Fe3W3C and Fe6W6C are the products. Tin was found to inhibit the overall reduction and carburisation reactions significantly. The potential for either efficient separation of iron and tungsten or a one-stage production of an iron-based metal carbide composite is discussed.

Jan 1, 1992

By Viviane Tavares

The liquid crystal display (LCD) are currently known by its vast application in electro ? electronic devices, amongst them can be detached the devices of TV, laptops, electronic date, calculators and even though the mobile telephones (mobiles). The mobiles are changed more frequent of the TV for example, this happens due to the technology advance. With the constantly mobile exchange, the batteries, printed circuit board and liquid crystal display accumulation its become an environmental problem. To minimize the environmental impacts caused by mobile telephones residues are considered the segregation process of the LCDs main components, to goal to recover the recycle material. This process involves the use of treatment ore techniques with disc, hammers and balls mills. The process with best efficiency (about 98%) of LCD glass release was the hammers mill. The glass recovered can be used in the glass recycling and the sand substitution in the production of concrete blocks.

Jan 1, 2009

By Bowen Li

Copper vermiculite is a special nanomaterial with excellent antibacterial and antifungal performance. By means of ion exchange, copper vermiculite containing up to 5.8wt% copper was prepared. The chemical and mineralogical characterization of the material was investigated in this study based on the XRD, AAS, TEM and EDS analysis, as well as the calculation of crystalline parameters and crystal chemical formula. Cu2+ and Mg2+ have similar atom radius and same electrovalence. Correspondingly, the structure character of copper vermiculite is very close to that of standard Mg-vermiculite. Most of the CU21 may have occupied the interlayer cationic positions in the form of hydrate in vermiculite. However, some may have entered into octahedral coordinate positions. The values of au and bo of the copper vermiculite crystal cell have no obvious change compared to that of original vermiculite micropowder, but the Co value decreased slightly, which is desirable for the stabilization of the Cu2+ in copper vermiculite.

Jan 1, 2003

By Joseph Hamuyuni, Pekka Taskinen

We present experimental results for the liquidus in the system Cu2O - CaO -Al2O3 at 1250 oC. In this study, we quantified the liquidus by the equilibration/quench/analysis technique, with Cu2O, Al2O3, and CaO as primary materials exclusively. Experiments were conducted in air at an at oxygen pressure (p) = 21.3 kPa). Equilibrated specimens were quenched in brine solution of 10 wt% NaCl. We then quantified the liquid chemical compositions by means of Energy-Dispersive X-Ray Spectroscopy (EDS) and Electron probe micro-analyzer (EPMA). This study reveals inconsistences in liquidus surface of the present ternary diagram of the system here in mentioned. Differences of up to 10 wt % compositions of the species have been observed.

Jan 1, 2015

By Metehan Erdogan, Furkan Özdemir, Ishak Karakaya, Mustafa Elmadaglı

Tungsten is mainly produced by H2 reduction of WO3 which makes its production difficult and costly. A promising method was recently reported for direct electrochemical production of tungsten from CaWO4 (scheelite) which is estimated as the seventy percent of the all tungsten reserves of the world. This paper investigates the application of pulse current in the electrochemical reduction of CaWO4 pellets attached to a current collector. The electrolyte was composed of calcium chloride and sodium chloride salts at eutectic composition (48 pct mol NaCl at 873 K). The reduced samples were cleaned with dilute hydrochloric acid solutions and characterized by X-ray diffraction and scanning electron microscopy. Examination of the results revealed that metallic tungsten was obtained by pulse current reduction.

Jan 1, 2016

By Patricia Negrini Siqueira Poveda, Leonardo G. A. Silva

Thermoplastic materials are sensitive to ultraviolet radiation (UV), which can cause structural changes, causing variation in mechanical properties and appearance. UV range between 250 and 400 nm is considered the most aggressive to polymers, and prolonged exposure to it results in breakage and/or crosslinking chains. Light stabilizer additives, blockers or absorbers are added to the polymers for protection in order to extend the life of the final product. The choice of the adequate light stabilizer additive system depends on factors such as resin final application, thickness, geographic location of exposure, presence of fillers in the composition, contact with chemicals, among others. This study evaluates different additive systems: conventional organic, inorganic nanotechnologyc base and the synergy between them when applied to polyethylene considering carbonyl index and UV/VIS results after aging by QUV chamber.

Mar 1, 2017

By J. Kevin Cotchen

The results of "submerged arc" electric furnace processing of a variety of materials is discussed with respect to the process and products, including the characteristics of the products (e.g. TCLP or Toxicity Characteristics Leaching Procedure). The materials melted include slags and wastes containing various metal oxides including copper, tin, lead, zinc, chrome, nickel and other associated elements. The findings of these tests are compared to those reported in the literature for other operations treating similar "wastes".

Jan 1, 1992

By A. F. Usov

"The use of the Electric Pulse Discharge method of materials destruction (EP) for disintegration of materials in an industrial-waste processing are examined. The principles and Experience of the development device of EP-disintegration have been described, the technological efficiency of disintegration of industrial minerals estimated.IntroductionThe Russian scientists have proposed and comprehensively studied the electric pulse (EP) technique which is applied in ores and materials disintegration [1, 2 ]. The different aspects of the problem have been presented by the authors in papers at many international congresses [3-6]. Recently the technique is intensively developed in many countries, and various disintegration installations are exhibited.Crashing and disintegration of ores by EP-method is characterized by high selectiveness of destruction. It provides better disclosure of mineral grains and prevent it from destruction. EPmethod reduces slurry formation. All this provides better mineral extraction at ore beneficiation and improves concentrate quality. It also prevents the product from polluting with equipment metal, inwall and grinding equipment material. The possibility to change the character of dynamic loading allows controlling grain-size composition and getting small-size product in contrast to mechanical method of crashing.The product of EP-crashing is characterized by less toughness and greater specific surface area of grains since the new surface is formed at splitting and chinks extension. The product is of high sorption and reactivity in chemical changes. Open grains of mineral spots correspond to their natural condition and it is of great importance for studying mineral.The principles of the development deviceLong-term studies of the technique carried out by research institutes such as Research Institute of High Voltages (Tomsk), Kola Science Centre of RAS (Apatity), Institute ""Mekhanobr"" (S.Pertersburg), made it possible to substantiate principles of the disintegration installations design, make exploratory stands and technological installations to carry out pilot tests and operations under production conditions. The construction design of disintegrating installations depends on many technological and physical factors. Of all the technological factors, the most significant one is to preserve the liberated product because it is the peculiarity of the EPdisintegration to have high selectivity of disintegration. The preservation of the mono-mineral product liberated from the rock mass means that this product is not overgrinding, which causes the loss of the product with slime in processing, and that the initial natural form of the mineral inclusion is also preserved because it is the size and the integrity of crystals that determines its cost value (precious minerals). On the one hand, it is provided by a stage disintegration technique, with the product classified after each stage, and, on the other hand, by selection of specific conditions of electric breakdown, which ensure high performance of electric breakdown and effective disintegration of material fragments, with the useful mineral inclusions preserved intact, with its size considerably exceeding the discharge gap. These conditions are provided by the appropriate geometry of electrodes, the discharge gap and the screen size due to the material’s nature and grain size."

Jan 1, 2008

By Gen Kamimura, Hiroyuki Matsuura, Wonjin Choi

Control of non-metallic inclusions in terms of morphology, number density or composition is essential to produce steel products having the desired mechanical properties.Though many studies have been conducted to clarify various properties and evolution mechanisms of inclusions at steelmaking temperature, it has been reported that the states of inclusions in final products are significantly different from those in crude steels for some steel grades. The present study has focused on the evolution of oxide and nitride inclusions in solid Fe–Al–Ti–N alloys during heating to increase the understanding of inclusion evolution in a simplified metal system. Compositional and morphological change of initial inclusions, as well as precipitation and growth of new inclusions have been observed even when the alloy was in a solid state.This behavior has been observed due to the change of thermodynamic stability and solubility of existing phases in inclusions.

Mar 1, 2017

By Miguel Barron

Recently, a new lance design for BOF steelmaking has been proposed in the literature. This lance, in addition to six peripheral inclined supersonic nozzles, contains a vertical centered nozzle whose oxygen flow is independent from the main oxygen supply. The above authors affirm that their lance maximizes the droplet generation without causing spitting. In this work, the performance of a lance with four peripheral nozzles and one vertical centered nozzle is numerically modeled by means of Computational Fluid Dynamics software. Transient two dimensional computer simulations were carried out considering two phases, namely molten steel and gaseous oxygen. Numerical results confirm that bath agitation and droplet generation are enhanced as a result of the vertical centered nozzle, however a proper performance of this lance, related to a conventional one, strongly depends on the Mach number of the oxygen jets and the lance height.

Jan 1, 2008

By Ningchuan Feng

A biosorbent, the chemically modified orange peel, was prepared from hydrolysis of the grafted copolymer, which was synthesized by interacting methyl acrylate with cross-linking orange peel, and FT-IR spectroscopy was used for determining the structure of the biosorbent. Adsorption characteristics and effects of various factors of the biosorbent on Cu (II) were investigated including pH, adsorption time and initial concentration of Cu (II). Experiment results show that when pH was 6.0 and the initial concentration of Cu (II) was 50mg·L-1, the removal rate was 91.7% after 3 h adsorption. After four cycles being reused, 85.3% removal rate could be obtained by the biosorbent.

Jan 1, 2008

By I. H. Gundiler

Sandia National Laboratories (SNL) is tasked to support The Department of Energy in the dismantlement and disposal of SNL designed weapon components. These components are sealed in a potting compound, and contain heavy metals, explosive, radioactive, and toxic materials. SNL developed a process to identify and remove the hazardous sub-components utilizing real-time radiography and abrasive water-jet cutting. The components were then crushed, granulated, screened, and separated into an aluminum and a precious-and-base-metals fraction using air-tables. Plastics were further cleaned for disposal as non-hazardous waste. New Mexico Bureau of Mines & Mineral Resources assisted SNL in investigation of size- reduction and separation technologies.

Jan 1, 1995

By Linfeng Zhou, Rong Sun, Guanghui Li, Zhiwei Peng, Tao Jiang

The effects of microwave roasting on separation of rhenium (Re) and molybdenum (Mo) from a molybdenite concentrate have been investigated based on evaluation of the heating characteristics of the concentrate in the microwave field. The results show that a variety of operating variables, namely microwave power, sample weight, sample geometry, roasting temperature, roasting time and atmosphere significantly impact on the volatilization rates of Re and Mo. The optimum conditions for Re-Mo separation are microwave power 1300 W, sample weight 20 g, sample geometry pellets, temperature 600 oC, time 1.5 h, and atmosphere 20%O2. Under these experimental conditions, the volatilization rate of Re reaches 88.12%, while that of Mo is just 5.15%. Microwave-assisted roasting provides an alternative route to separating Re and Mo from molybdenite concentrate.

Jan 1, 2016