Search Documents

By Antonio de Ita, Isaias Hilerio, Miguel Barron

"The influence of an unconventional lance with a central nozzle on the multiphase fluid flow in a steelmaking converter is studied in this work by means of computer simulations. The lance has four peripheral supersonic nozzles and a vertical central nozzle. Besides, the oxygen flow in the central nozzle is considered independent from the main oxygen supply. Transient two-dimensional numerical simulations were carried out considering just molten steel and gaseous oxygen as the existing phases. Numerical results show that bath agitation and droplet generation are enhanced as a result of the central nozzle. However, the performance of this lance strongly depends on the distance of the lance tip to the molten steel surface and the velocity of the oxygen jet.IntroductionCurrently, two thirds of the world crude steel is produced through the steelmaking oxygen converter [1]. Given the unquestionable economic importance of this technology, any improvement or optimization proposal is welcome. In the majority of current oxygen converters a top oxygen supersonic jet is blown onto the molten steel through a water-cooled lance to eliminate by oxidation some impurities such as carbon and phosphorus. Conventional lances have inclined peripheral nozzles whose number depends on the converter capacity. During the process, a large amount of gases evolves, forming metal droplets and a metal-slag-gas emulsion [2]. The droplets and the resultant emulsion increase the reaction interfacial area, promoting in this way carbon removal and dephosphorization of the molten steel bath [3]. However, during the blowing stage, the emulsion rises towards the lance and converter mouth and frequently forms layers which accumulate in the lance, reducing the life of the lance tip [4, 5]. It is possible that some freezing of the molten metal occurs due to the low oxygen injection temperature, however there are no reports on this. Besides, frequently undesirable operating phenomena such as spitting and slopping may arise as a result of inappropriate blowing practices or bad lance design. In the oxygen steelmaking industry, novel lances design are needed in order to enhance the decaburization rate and the slag formation and, at the same time, preventing operating practices that decrease productivity and move away the shop from safety standards."

Jan 1, 2012

By J. E. Sallee

An experimental study has been conducted on the level of arsenic contamination in samples of zinc oxide when the zinc oxide is contacted with gas mixtures containing As4O6(g). This contamination has been determined as a function of A4O6 saturation pressure, temperature, zinc oxide sample surface area, impurities, and oxygen level in the gas mixture. The results indicated a rather clean separation can be achieved between condensed zinc oxide and gaseous arsenic oxide as long as attention is given to temperature control, and the final zinc oxide surface area. For a 300°C operation temperature and an AqOg saturation pressure of 0.38 TORR (or 0.05% As406 by volume), the contamination level is expected to be approximately 100 ppm. This suggests that arsenical dusts can be treated in the HRD flame reactor process and a reasonable purity zinc oxideproduct produced. The results also show no evidence of zinc arsenite or zinc arsenate formation.

Jan 1, 1994

By Geoffrey S. Plumlee

The Summitville gold mine, located in southwestern Colorado, received tremendous publicity in the 1980's and 1990's for leaks of cyanide solutions from its heap leach facility. As is typical with cyanide spills, real time, geochemically rigorous assessments of the environmental effects were not performed. Past United States Geological Survey (USGS) research used simple mixing experiments to model the influx of alkaline cyanide heap leach solutions from Summitville into a nearby stream, whose waters were highly acidic due to severe acid-rock drainage (ARD) from the mine. These experiments indicated WAD cyanide rapidly degraded due to formation of Fe-Cu-CN solids and lesser HCN volatilization. The alkaline heap leach solutions also precipitated hydrous iron-and aluminum, oxides and hydroxysulfates (iron and aluminum 'supplied by the acid. rock drainage (ARD]), which then sorbed copper and other heavy metals from the ARD. These results indicate that mixing of cyanide heap leach solutions with ARD may be a cost-effective remedial method at mine sites where treatment of both is required. New experiments are currently in progress to further refine a potential remedial process.

Jan 1, 1998

By Alan M. Peel

"Over the past years there has been an increasing demand by aluminium cast -house operations to obtain a greater return from their existing installed plant. This has included increasing existing furnace production capacity to match new and higher downstream production requirements, reducing melt losses and more efficient alloying.The paper discusses how Electromagnetic Pumping, which was developed for the combined purpose of;1. Melting light gauge aluminium scrap with a reduced melt loss and; 2. Effective circulation of the aluminium melt,has established its self in recent years, as an effective means of satisfying many of these industry requirements, but how it has also provided many other additional operational benefits to the aluminium cast house.The paper will discuss operational performance of the system with a particular emphasis on its effect on the metal bath quality (alloying, chemical and temperature homogeneity), metal recovery and increased production due to the high circulation.The technology having now been adopted by a variety of industry leaders has a number of prominent references and the paper will discuss the operational benefits and experiences from some of these."

Jan 1, 2000

By G. S. Rao

Levitated drops of Fe-18%Cr-2%C were reacted with oxygen-argon mixtures to study the reactions that occur in the AOD process, where the gases are injected into the melt and form bubbles. In the laboratory an argon-oxygen pulse, followed by pure argon, was flowed past the levitated drop to simulate the transient conditions in the gas phase as the bubbles rise in the melt. Oxide layers formed on the drops immediately when they came into contact with gas pulses containing 75% or more oxygen. Once the oxygen flow had ceased, the oxides reacted with the carbon in the drops to form CO gas and eventually disappeared. The de-carburization reaction occurred without oxide formation when the gas contained 50% oxygen or less. Melts that were sampled after EAF tapping, ready to be charged into the AOD, showed a higher tendency to oxide formation and consequent carbon boil than pure ternary Fe-18%Cr-2%C alloys made in the laboratory. The actual steel samples contained significant impurities, such as 0.25% Si and 0.56% Mn. A similar effect of oxide-forming impurities had been observed previously with binary Fe-C alloys. Movies were taken of the oxide formation and decomposition, and the results will be presented, along with data on the experimental conditions, including temperature and oxide compositions. The results are important because they give an insight into the reaction mechanisms in the AOD, which must be understood in order to improve and model the process.

Jan 1, 2006

By Yuan Zeping

The Guixi smelter is the first Outokumpu flash smelter in China .It was commissioned on December 31, 1985. Originally, the smelter was designed to produce 90,000 tonnes of copper annually. After the implementation of oxygen enrichment and other modifications, the smelter will reach its anticipated annual capacity of 200,000 tonnes of copper in December 1999. This paper describes the performance of the smelter, the first phase modification project and the second phase expansion project which have made Guixi one of the best copper smelters in the word through the use of existing and innovative technologies.

Jan 1, 1999

By Murat Alkan

In this study, a self-propagating high-temperature synthesis (SHS) and following acid leaching techniques were carried out to produce boron carbide (B4C) powder. First, B2O3 was obtained through calcinations of H3BO3 at 1073 K for 2 hours. Then, the glassy B2O3 obtained was crushed and sieved. In the SHS experiments, different amounts of B2O3, Mg and C black were used. The SHS product was obtained in the form of black, spongy solid. In the leaching step, the SHS product was leached in a HCl solution to eliminate the MgO and Mg3B2O6. The effect of acid concentration on the selective leaching was studied at different concentration range, solid/liquid (S/L) ratio, and temperature. The products obtained were characterized by using X-ray diffraction, chemical analysis and SEM techniques.

Jan 1, 2009

By Yavuz Ali Topkaya

Rare earth ferrosilicide is a versatile alloy mainly used to control the detrimental effects of sulfur in steel and to modify graphite structures in cast iron. The aim of this study was to determine the optimum conditions to make rare earth ferrosilicon alloy using a preconcentrate produced from a bastnasite type of ore present in the Beylikahir-Eskisehir region of Turkey. This concentrate contained 23.5%REO, 41.37% CaF2, 10.69% BaSO4, 8.50% CaCO3, 4.18%Fe2O3, 2.83% Al2O3, 2.74% SiO2, 1.20% P2O5 and small amount of other oxides. The initial metallothermic reduction of this concentrate using ferrosilicon and aluminum in a graphite crucible placed in a muffle furnace gave very low recoveries due to the difficulties encountered in adjusting the slag composition, temperature and amount of additives. Therefore, two batches of rare earth oxide concentrate containing 61.1% and 81.7% cerium oxide, respectively, that were procured from a Turkish glass producer, were used to optimize with respect to temperature, duration, slag-making additives and amount of reducers. In these experiments, smelting and reduction was done in an induction furnace with graphite crucible, and, ferrosilicon and aluminum were added after melting the charge. As a result, there was no difficulty in obtaining a rare earth ferrosilicon alloy containing 35-55% RE, 5-25% Fe and 20-40% Si, with about 80% metal recovery. When the optimum conditions were applied to the preconcentrate, alloys of similar compositions were obtained with 70-80% recovery. Experiments were also done with mixtures of preconcentrate and rich concentrate, and, recoveries as high as 95% were obtained. Only in this case, to increase the recovery, mixtures had to be charged to the empty graphite crucible after heating the crucible to the required temperature.

Jan 1, 2006

By Hui Lu

The structural changes in solutionized AA2618 during natural aging and their effects on subsequent artificial aging were investigated by hardness measurements, X-ray diffraction, differential scanning calorimetry and transmission electron microscopy. The changes in lattice parameter and hardness during natural aging indicate that copper-enriched clusters form in the earliest stage, followed by the formation of magnesium-enriched clusters and coppermagnesium co-clusters. Prior natural aging consistently weakened the hardening during subsequent artificial aging at 180, 200 and 230 °C but had no effects on artificial aging at 150 °C. The decreased age hardening was attributed to the reversion of small clusters/zones that formed during prior natural aging. The lattice parameter exhibited erratic changes with increasing artificial aging time, reflecting the complex sequence of the reversion and precipitation.

Jan 1, 2006

By Heric Henrique Souza e Silva, Johne Jesus Mol Peixoto, Natalia Barros Barony, Itavahn Alves da Silva, Weslei Viana Gabriel, Carlos Antonio da Silva, Varadarajan Seshadri

In this work the circulation rates have been determined in a 1:7.5 scale physical model of RH reactor (Ruhrstal Heraeus) and using oil/water and oil/zinc chloride solution to simulate steel melt/slag in the prototype with the objective of evaluating the influence of density and viscosity on the entrainment of oil simulating slag. A technique based on strain gage bridge and particle image velocimetry was developed to assess the circulation rate, as the usual tracer method is not feasible due to the presence of chloride ions in ZnCl2. The critical velocity and critical diameter of oil drops for slag (oil) entrainment in water/oil and ZnCl2/oil systems were estimated using equations from the literature. Due to the difference in density, the ZnCl2/oil system, showed a critical velocity that is 28% higher than the silicone oil/water system while the maximum size of the entrained droplets was about 65% lower than that for water/oil system.

Mar 1, 2017

By Heimo Thalhammer

During the refining of lead, copper or other metals the furnaces used in the process · often produce waste gases. This paper illustrates how these waste gases can be successfully treated and destroyed by CTP 2-bed or multi-bed compact systems, modified for the additional reduction of dioxins and furans. The CTP regenerative thermal oxidizer also destroys voes (organic compounds and odours) using ceramic blocks as a heat exchanging media. The raw gas is forced through the ceramic beds where it is heated up to the oxidation temperature level. The voes, dioxins and furans are destroyed in the combustion chamber, subsequently generating water, eo2 and heat. The hot purified gas heats up a second ceramic bed, which is used to preheat the raw gas after the valves have been switched. This process does not produce any secondary waste such as contaminated water, polluted air or any other products that have to be disposed of.

Jan 1, 2000

By David Norval

Water solidification of mattes, metals, alloys and certain slags with high metal entrainment has customarily not been practiced due to the belief that such processes are too dangerous and unproven in the Pyrometallurgical Industry. Slag granulation on the other hand is extensively applied, although in some cases crudely, with disastrous effects, as a result of not recognising the high heat capacities prevalent in slags. This paper will examine the most common air solidification processes and compare such processes with water solidification, mainly slag and matte granulation processes and design criteria for safe and reliable operation. Finally, purpose designed granulation and solidification processes will be discussed taking into account specific applications and the individual signatures of alloys and slags, emphasising that no slag, matte or alloy responds in similar fashion to a granulation practice.

Jan 1, 2006

By L. R. Verney

About 75% of the market economy countries's supply of cobalt is produced in Central Africa by Zafre and Zambia. Zafre alone accounts for more than 55% and has the resources and capacity to increase output significantly at any time so its dominant position is unlikely to be challenged in the foreseeable future. Other producers from domestic resources are Canada, Australia and South Africa; and Cuba, probably the most important producer outside of the Market Economy countries. Belgium, Norway, France, Japan and Finland produce cobalt from imported materials. While there are "cobalt ores", inMorocco, USA, Canada and the USSR, the mineralisation is complex and cobalt extraction is costly. In ZaPre and Zambia cobalt is a by-product of copper; in Canada, Australia, France, and Cuba it is a by-product of nickel; and in South Africa it is a by-product from the production of Platinum Group Metals. Thus the levels of cobalt production are inevitably related to the production of other primary metals. While some cobalt is produced by predominantly pyrometallurgical methods most of the world's cobalt is produced hydrometallurgically. The existence of large hydro-electric power plants and the mineralogy of the copper and cobalt concentrates encouraged research and development in Zafre of the recovery of copper and cobalt by electrowinning from sulfate solutions; much pioneering work was carried out, which lead to construction of the two largest copperlcobalt hydrometallurgical plants in the world, at Shituru and Luilu. Similar systems were adopted in Zambia. In Canada high pressure hydrometallurgical processes based on the sulfate system were developed and adopted in Australia, the Philippines, Finland and South Africa. Meanwhile developments in chloride hydrometallurgical extraction of nickel and cobalt lead to its use in the extraction of cobalt in Norway, France and Japan.

Jan 1, 1988

By Ramona Prillhofer

Salt slag is a waste product produced by the recycling of aluminum. In most European countries (e.g. Austria, Germany) the landfill disposal of this waste is forbidden because the slag contains soluble salts and these represent a potential source of pollution to the surface and groundwater. Additionally, consisting metal and some compounds in the salt slag can react with water and resulting from this, noxious gases are generated. The recovery of useful materials from these wastes is accordingly both environmentally necessary and economically feasible. This study describes a complete recycling-process for the salt slag, which includes a leaching-cristallization-process to obtain the oxidic residue, a pyrometallurgical-step to clear the oxidic residue and finally an extensive characterization of the achieved products. Due to the increasing price of raw materials, the utilization of the oxidic residue into commercial products has been investigated and application possibilities will be discussed.

Jan 1, 2009

By NRMR Bhargava

With the increasing use of lead-free solder alloys, low melting point alloy is often required due to the heat- sensitive parts or substrates in modern electronic devices. For such demand of low melting point, the nanostructure lead- free solder alloy, having excellent metallurgical characteristics and a melting point of <215oC, were developed by mechanical attrition of conventional lead free solder alloys (Sn-Ag-Cu, Sn-Ag and Sn-Cu). The decrease in melting point due to nanosize effect was calculated theoretically as function of particle size and the theoretical results were compared with experimental values measured by differential scanning calorimetry. The newly developed alloys have eutectic composition of Sn-3.5Ag-0.7Cu, Sn-3.5Ag and Sn-0.7Cu and the melting point depression found to be 5.10C, 4.10C and 6.20C when the bulk alloys reduced to 80 nm, 92nm and 96nm sizes respectively.

Jan 1, 2009

By Sergio N. Monteiro

Polymeric matrix composites with dispersed hard particles are being as wear resistant tools in industrial polishing operations. In the present work, the microstructure of epoxy composites with different amounts of embedded diamond particles, up to 30 wt.%, was investigated for the effect on fracture characteristics. It was found that the introduction of diamond particles promoted an increase the porosity of the epoxy matrix. Moreover, the particle morphology associated with a non-uniform distribution within the matrix was responsible for the nucleation of cracks that caused rupture of the composites.

Jan 1, 2006

By N. V. . Panishev

The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Samples of iron ore and carbon reductant were chemically and physically analyzed. Green pellets were processed via a lab tube furnace to simulate RHF conditions. The nuggets and slag were chemically analyzed. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.

Jan 1, 2010

By Jana Dobrovska

The paper deals with new approach for measurement and evaluation of chemical microheterogeneity of elements in polycomponent metallic systems (i. e. steels, Ni-alloys). The method is based on the original mathematical model for determination of distribution curves of dendritic segregation of selected elements and on the original mathematical model for determination of the effective partition coefficients of these elements in the structure of analyzed alloy. Application of the method at research of chemical heterogeneity of continuously cast steel slab is also presented. The original results of measurement of dendritic microheterogeneity of eight elements (Al, Si, P, S, Ti, Cr, Mn and Fe) in structure of nine zones of a transversal section of slab are given.

Jan 1, 2006

By Linli Wu

During the measurement of contact angle, a misty band was observed near the substrate. Hsien-Nan Ho and Shinn-Tyan Wu thought this was because the oxygen atoms on the interface migrate to the droplet surface to form an oxide band near the substrate. But from our experiments misty band appeared before the drop reach to the substrate. Theoretically speaking, the oxygen partial was the same everywhere in the vacuum furnace. So there was no condition to provide enough oxygen forming oxide. This appearance would be explained more reasonably with the optics principle. Most reflected light would be absorbed by the substrate and the light cannot reach the observation area, so the misty band formed.

Jan 1, 2006

By F. Patisson

One of the major issues with multiparticle reactors is to handle their multiscale aspect. For modeling, it usually comes to coupling a reactor model (describing the phenomena at the macroscopic scale) with a so-called grain model (simulating the behavior of a single grain or a particle). An interesting approach proposed by H.Y. Sohn (1978) is to use the law of additive reaction times in order to calculate, approximately but analytically, the reaction rate of a particle in the reactor model. Its great advantage, compared to a numerical grain model, is to drastically reduce the computation time, particularly in the case of complex reactor models. This is the approach we retained for modeling the moving bed furnace, a counter-current gas-solid reactor used in the nuclear fuel-making route for producing uranium tetrafluoride from uranium trioxide. The numerical model we developed is 2-dimensional, steady-state and based on the finite volume method. It describes solid and gas flow, convective, conductive and radiative heat transfers, and six chemical reactions involved in the process. The law of additive reaction times is used to calculate analytically the rate of the three principal gas-solid reactions at every discrete point in the reactor. We have demonstrated the validity of this approach by comparing its results with those calculated from a numerical grain model. Also detailed in the paper are the main results of the moving bed furnace model itself and the possibilities of optimizing the process revealed by the calculations.

Jan 1, 2006