Search Documents

By Oleksandr Liaskovskiy, Sergey Beringov, Sergiy Yatsuk, Timur Vlasenko, Iryna Buchovska

"Working with solar-grade silicon for solar cells application usually meets some difficulties in comparison to polysilicon produced by Siemens method: higher impurities content leads to lower yield, worse electro-physical parameters and poor performance in solar cells application. However some adjustments in ingot production can show significant improvements in quality of final product: crystalline wafers and cells.Recent investigations have shown that solar-grade silicon is suitable for high effective production process such as mono-like multicrystalline wafer production. Production-scale lots made at Pillar show promising results for solar-grade silicon application: high-quality wafers with significantly big crystalline grains of <100> orientation.IntroductionThe standard technology of producing multicrystalline silicon ingots by directional solidification method in quartz crucibles has a number of disadvantages resulting in limited efficiency of solar cells made of multicrystalline material: crystallites of multicrystalline ingot are relatively small (down to 5 mm size), grain borders of crystallites contain parasitic impurities such as metals, silicon nitride etc., crystallographic orientation of crystallites is random. The listed deficiencies are an integral characteristic of the technology which affects the efficiency of solar cells, such as presence of solar cells with low efficiency even at a high level of average efficiency, problems with shunted cells, silicon nitride inclusions, which adversely affect cell efficiency and are centres for silicon carbide formation, impossibility of application of high effective alkaline texturing etc. Also with regard to the targets set by photovoltaic to reduce the cost per Wp in the nearest future, standard technology of multicrystalline silicon ingots production by directional solidification faces certain challenges some of which are hard to overcome due to rather low efficiency of solar cells made of multicrystalline wafers. Therefore alternative methods of multicrystalline silicon production for photovoltaic application having a number of advantages in comparison to traditional technology are developing rapidly."

Jan 1, 2012

By Neale R. Neelameggham

"Most chemical process plants and metallurgical production facilities have some sort of cogeneration to minimize process energy costs. Use of Alternative Energy Production from sun and wind power with storage can become an integral part of a process plant utility. This will facilitate reduced fossil fuel usage and help minimize thermal emissions. This will be similar to Pollution Control equipment, which have become an essential part of process plants in the past four decades. Conceptual flow sheets of such Process Utility schemes are presented.IntroductionPower is supplied to industries, commercial and residential users. Over the past decade, Electric Utility companies have made major inroads, in introducing alternative energy resources in an attempt to somewhat reduce fossil fuel use in power generation. Now, on a much larger scale than in the early 1980s, residential users, motivated by government provided tax credits, have started installing alternative energy generators such as roof top wind mills or roof-top photovoltaic generators. This will minimize future energy costs, help control thermal emissions etc. This alternative power generation is typically connected to the existing power grid with two way power metering. However, the use of alternative energy generation has not been seen at large industrial sites yet.Paul Scherer Institute, Switzerland and the NREL laboratories in Colorado, are two of the several institutes which have been developing how solar thermal power can be used to supply the endothermic input energy in chemical and metallurgical processes. The theme of this present symposium addresses the above as well as the energy storage needs for such events to become continuous. This paper emphasizes the concept of how alternate energy can be used in the production of materials on a generic sense wherever there is a need for input energy – beyond endothermic process energy - while addressing how to reduce the thermal and carbon emissions.The alternative energy generation using wind or solar source is discontinuous due to the nature of the energy source. They are not only discontinuous but also variable. This necessitates storage of generated power for close to continuous use with variable loads. C Smith, et al pointed out in 2006, that 'the electric power industry has taken notice of the expansion of wind and its potential' in a summary article on integrating wind generation into utility systems.1 In 2009, the 1000 MW wind generation project in Texas had to be postponed to 2013 for lack of transmission.2 There are only a few large MW solar generation units in the US; the projects being slow mainly from lack of adequate storage and redistribution."

Jan 1, 2010

By M. A. S. Siraa

A program of work was undertaken at the Kennecott Smelter and Refinery to model the complex. This effort contributed a total of eight models of the plant: flash smelting furnace, flash converting furnace, slag concentrator, anode furnace, offgas scrubbing system, acid plant, hydrometallurgical dust treatment plant, and the precious metals plant. Some of these models have been used in a variety of investigations ranging from offgas capacities for a steam generation analysis to an examination of impurities. The culmination of this enterprise has resulted in an on-line control scheme for the flash smelting and flash converting furnaces. These two process control schemes incorporate their respective steady-state heat and mass balances that are executed in response to feed changes while a feedback loop calculates when product grade and temperatures deviate from setpoints. This system has been put into place to improve furnace control and on- line time.

Jan 1, 1999

By T. Malvik

Norway is a big producer of ferrosilicon and silicon metal. The raw material is quartz and quartzite and large quantities from both Norwegian and foreign sources are used. The demands maade on both the chemical purity and the thermomechanical qualities of the quartz/quartzite have increased in recent years in an attempt to reduce energy consumption and to improve utilization. Control of the chemical quality of the raw material is relatively easy by means of routine analysis, but it is more difficult to find a suitable method for testing the thermomechanical properties. A rapid test method to define high quality quartzite deposits for use in the metallurgical industry has been developed. The method is based on a combination of chemical analysis, dilatometry, thermosonimetry and cathodoluminiscence.

Jan 1, 1989

By R. P. Tavares, M. Isac, R. I. L. Guthrie

"The configuration of the metal delivery system used in twin-roll casting can play a significant role in determining both internal and surface quality of the strips produced by this process.In the present work, a mathematical model for coupled turbulent fluid flow, heat transfer and solidification was developed and used in the study of metal delivery systems for twin-roll casting of low-carbon steels. This study was applied to a pilot twin-roll caster being investigated in Canada, with a roll radius of 0.3 m, producing strips of thicknesses from 4 to 7 mm, at roll speeds ranging between 4 and 12 m/min. Various configurations of metal delivery systems were simulated and their effects on the advance of the interdendritic solidification front and levels of turbulence and temperature within the caster investigated. According to the predictions of the model, an extended nozzle with inlet flow towards the surface of the rolls seems to be the best alternative for feeding liquid steel into twin-roll casters.A full scale water model of a pilot twin-roll caster was also built and used to qualitatively validate the predictions of the mathematical model.Various techniques for fluid flowvisualization were applied. In general, the predictions of the mathematical model were in reasonable agreement with the experiments with the water model."

Jan 1, 1999

By D. A. Hayman, J. D. Steenkamp, G. M. Denton

Design of furnace containment systems can be based on one of two design philosophies: Insulating or conductive lining designs. In insulating lining designs, management of the compatibility between refractory materials and process materials (typically liquid metal and/or slag) is an important criterion for furnace design, and an important process parameter to control during furnace operation. In conductive lining designs, management of the integrity of the layer of frozen material (freeze lining) on the interface between the liquid process material, and the refractory lining, is important. For example in ferrochromium production, both lining design philosophies are applied. The work presented here discusses the significance of lining design philosophy in the context of ferrochromium production.

Mar 1, 2017

By Nobuyuki Masuda

In Japan, the municipal solid waste, which amounts to 50 million tons, is generated every year and most of it is incinerated. The fly ash from the municipal waste incineration (the primary fly ash) contains heavy metals, such as lead and zinc, etc., and dioxins. In case of melting, the fly ash from the process (the secondary fly ash) contains high concentration of heavy metals (e.g., Zn; 1-20%, Pb, 1-10%). Metal Mining Agency of Japan launched a four-year project in 1999 to establish the integrated technologies to recover the valuable metals from, and to decontaminate, the primary and secondary fly-ashes in the practical scale by utilizing the existing metallurgical processes and facilities, along with the energy saving. The segregation, flotation and chemical treatment are applied to the treatment of the primary fly ash. The secondary fly ash is treated with MY (Mitsui-type blast furnace) Process after the chlorine removal to recover the heavy metals in the ash, In this paper, the segregation and flotation process for primary fly ash and MF process for secondary fly ash are explained. The main results of experiments done from 1999 to the mid of 2001 to design the pilot plants and to optimize the operating conditions are described. The main results of the experiments are as follows: - The segregation reaction of Cu was confirmed by the experiment on the treatment condition of 800 and 900`C with adding oil cokes and water to the primary fly ash, and 99.98% (toxicity equivalent) of the dioxins were decomposed by the treatment. - Washing tests of secondary fly ash to feed MF resulted that more than 70% of chloride were removed, but still lower than expected, and agglomeration tests were successful by the results of the sufficient strength of briquettes produced though a little more binder for the agglomeration is required than usual operation. - Smelting experiment by downsized MF showed that valuable metals, such as zinc and lead, are recoverable in the furnace dust. Recovery ratios, Zn: 58% and 67%, Pb: 74% and 83%, are accomplished.

Jan 1, 2002

By N. Tsuchida

Sumitomo Metal Mining Co. Ltd. (SMMC) is currently developing the flowsheet to treat stockpiled limonite, a type of laterite ore, at Rio Tuba on southern Palawan Island, Philippines. The new plant will be commissioned at the end of 2004. Rio Tuba Nickel Mining Corporation (RTNMC) has been mining saprolite since 1977, and the limonite ore located above the saprolite ore body has been stockpiled separately according to nickel and magnesium content. Ore from these stockpiles will be blended and used for the operation. The annual production of nickel will be 10,000 metric tons for the next twenty years. The proposed process consists of ore preparation, high pressure acid leach (HPAL), counter- current decantation wash, impurity removal and sulfide precipitation. Precipitated mixed sulfide will be processed to electrolytic nickel by the Matte Chlorine Leach Electrowinning (MCLE) process at Niihama, Japan. SMMC has established new technologies during the process development, such as zinc removal and sulfide precipitation. Applying this technology, preferential removal of zinc can be achieved by hydrogen sulfide gas with negligible loss of nickel. Precipitation of nickel by hydrogen sulfide gas is carried out at low temperature. Slow kinetics is selected for control of the particle size of the precipitated mixed sulfide. Keywords: HPAL, Zinc Removal, MS Production

Jan 1, 2004

By N. Tsuneyama

Sumitomo Metal Mining Company has been operating Waelz Kiln at the Shisaka Works for 12 years to recover zinc and lead from electric arc furnace (EAF) dust. To increase the capacity and cut down the operating cost, some improvements have been carried out resulting in the capacity of 60,000 t/ y of EAF dust as compared with 32,000 t/ y in 1977. The current capacity is equivalent to 20% or EAF dust generated in Japan. The number of workers has been decreased by the introduction of an automatic control system, and the productivity per worker is now twice as much as 10 years ago. This paper will describe the progress of the operation at the Shisaka Works after the previous? paper reported in "Zinc&apos; 8 5? and summarize the status or EAF dust recycle in Japan.

Jan 1, 1990

By X. Jay Gao

A fast high-temperature carburizing process integrated with materials design and optimization via a systems design approach was developed to significantly reduce process cycle time. Process experiments were focused on boost cycles to obtain a robust boost process and investigate surface reaction kinetics, primary carbide formation and dissolution. Weight gain and microhardness were measured, all showing evidence of non-monotonic time evolution for longer boost times at higher temperatures. Optical and electron microscopy and other techniques have been used to identify possible carbides, their location and types. These results assist the picking of first boost time with least variation rate in terms of content of case carbon and carbides, dissolvable in subsequent diffuse if any. The results also provide critical information to properly formulate surface reaction kinetics and diffusion and formation kinetics of carbides modeled using DICTRA. Keywords: high temperature vacuum carburizing, partial pressure carburizing, heat treatment, process development, carbide, case hardening, microstructural analysis, over carburizing

Jan 1, 2003

By David K. Melgaard

Electroslag Remelting (ESR) is a complex process used to produce high quality specialty alloy materials. The quality can be directly correlated to variances in melt rate and immersion depth. Conventional ESR furnaces control these quantities using two independent control loops using proportional changes in current for melt rate and driving the electrode up and down to match a voltage set point for immersion depth. However it is well known that the control loops are highly coupled, i.e. changing the current to account for melt rate deviations changes the voltage depth relationship and vice verse. In addition the noise in measurements of the ESR process can be considerable, forcing conventional controllers to use highly damped responses. A new model-based controller has been developed to embody the coupling and improve responsiveness by using estimates from a reduced-order linear ESR model and the typical process measurements to control melt rate and immersion depth simultaneously. Kalman filtering is used to optimally combine the model estimates of eight process states and the measurements of voltage, current, position and mass to estimate the instantaneous melt rate and immersion depth. Several ESR melts under steady state and transient conditions were conducted to evaluate the performance of the new controller. This paper will discuss the design of the new ESR model and controller and will present experimental results demonstrating its much improved control and responsiveness. While this controller was developed for the ESR process, the effectiveness of model-based control in managing such a complex process with relatively simple equations suggests the approach could be employed for many other processes as well.

Jan 1, 2006

By Dinesh Goyal

Industrial fly ash from (electro static precipitator) was mixed with soil at different levels on v/v basis for raising of pulpwood tree species. In field trials conducted on degraded soils increase in the plant growth of Eucalyptus tereticornis, Acacia auriculiformis and Casuarina equisetifolia by 10 %, was observed during the initial six months after plantation at 18-24% (v/v) fly ash concentration which was at par with chemical fertilizer treatment. Level of As, Se and Mo in flyash was 6.2, 3.6 and 4.0 ppm respectively. The radioactivity analyses 40K, soil and 28 fly ash showed that the activity levels of gamma emitting radionuclides K, Ra, Ac were within the permissible limits and mixing of fly ash with soil at tested concentration would have no deleterious effects. Available Co, Cr, Ni and Cd in rhizospheric soils were below detection limit. Fly ash at 10-20 % level (v/v) was also found to be a good potting mix material in forestry nurseries in terms of improving biomass production by 20 %, when tested in nursery seedlings of Eucalyptus tereticornis. Nursery addition of fly ash in soil decreased soil dehydrogenase activity and the soil bacterial population was negatively affected. These results indicate that use of fly ash in forestry sector involving nursery and plantations as a soil amendment agent upto 10-20 % v/v is a gainful utilisation of fly ash.

Jan 1, 2002

By Fumito Tanaka

The Mitsubishi Process is the sole pyrometallurgical process for the continuous production of blister copper from copper concentrates. Continuous converting originates from the application of the proven technology of a lime-ferrite slag (CaO-FeOX-Cu2O) on the Converting Furnace (C-furnace). Recent improvements on the C-furnace operation have included increasing the processing of recycled materials and the investigation of alternative fluxing agents. However, some minor oxides adversely affect C-furnace operation, with respect to magnetite behavior of the slag, with the most significant impact having been observed with the silica content of the slag. This paper will quantify the impact of silica on the lime-based slag, and discusses the controls that have been identified to sustain continuous converting operation.

Jan 1, 2005

By Milton Blander

A review of concepts and theories for predicting thermodynamic solution properties of multi- component high temperature liquid solutions is reviewed. During the last 50 years the ability to predict :such properties for molten salts, silicates and metals based on the generally known properties of the lower order (often binary) systems has been developed and shown to provide predictions which are quite useful in science and technology. There are many gaps in our understanding of these high temperature solutions, especially for metals, and considerably more work is needed.

Jan 1, 1996

By Hua Hou, Xiaofeng Niu, Wei Liang

"The explicit finite difference (EFD) method is used for calculating the casting temperature field during solidification. Because the time step is limited, the computational efficiency of the EFD method is lower. In order to improve the computational efficiency, a fourth-order in space and second-order in time model based on the equivalent specific heat method and the alternating direction implicit (ADI) method is established. The degree of similarity between the simulation results and the experimental results is analyzed. The results show that the simulation results of this high order mathematical model are close to the experimental results.IntroductionThe 3D heat transfer equation of temperature field during solidification process is as the following: [1-3]."

Jan 1, 2013

By N. Kanari

One of the criteria to define the market value of chromite concentrate is its chromium to iron ratio. Changing this ratio for a definite chromite mineral is impossible by physical processing. This study investigated the possibility of increasing this ratio through the carbochlorination and the oxychlorination of chromite concentrates. Experiments are carried out up to 1000 °C. The characteristics of samples and reaction products are determined by SEM, XRD and chemical analysis. The carbochlorination of a chromite concentrate at about 600 °C leads to the . selective partial elimination of iron allowing a higher Cr/Fe ratio of the treated concentrate. Selective extraction of iron could also be achieved at about 950 °C by oxychlorination. In this case, a part of chromium contained in the concentrate is recovered as chromium oxychloride. The obtained residue had high content of Cr, Mg and A1 oxides. Such material has probably better chemical and thermal properties that may. be useful for foundary and refractory applications. Two flow-sheets for the beneficiation of the chromite concentrates using carho- and oxychlorination are suggested.

Jan 1, 1997

By Tuneo Funahashi

Sumitomo Shisaka Works has been treating EAF(Electric Arc Furnace) dust to recover zinc and lead in the Waelz Kiln process. Since its commencement of operation in 1977, many technical improvements have been successfully made to increase the production capacity and the zinc recovery rate. The EAF dust charge to the Waelz Kiln was increased from 35,000tly to 120,00OtIy, and the production of zinc oxide now amounts to 40,000tly. The zinc content in the clinker was decreased from 5% to less than I%, by the optimization of the kiln heat pattern with no accretion trouble. And the clinker has become more a valuable raw material for steel making. This paper describes the above progress ofthe SMM Waelz Kiln process operation at the Shisaka Works.

Jan 1, 1998

By Tan Pengfu

By using computer-aided techniques of equilibrium calculations for multicomponent and multiphase systems, a computer model has been developed to simulate QSL, KIVCET and Outokumpu flash lead smelting processes. A mathematical description is studied using two zones or three zones, namely smelting zone and slag reduction zone for QSL furnace, or offtake shaft zone, smelting shaft zone and electric furnace zone for KIVCET furnace. The amount of each component in lead, slag and gaseous phases under equilibrium is calculated by using the data of free energies of formation and activity coefficients. The predictions by the present computer model are compared with the known data from QSL-Plant at Korea Zinc Co. in Korea, KIVCET-Plant at Nuova Samim Co. in Italy and Outokumpu Co. in Finland. The agreements between the computer predictions and the known data are excellent, so that the present computer model can be used to monitor and optimize the actual industrial operations of direct lead smelting.

Jan 1, 1998

By John R. Howell

"SUMMARYThe process of producing a new cast component requires significant design and development by both the design engineer and the foundry engineer. This effort strives to produce a high quality component at minimum cost. To assist in this development, an analysis system, consisting of several computer programs, has been developed to simulate the metal casting process. This system incorporates analytical geometric solid modeling, finite element analysis, results display, and an innovative technique to model the casting mold with surface boundary conditions.The simulation has produced excellent thermal results and work is in progress to develop techniques to enable use of this data in additional analyses to predict porosity and residual stress. Research is required to produce working parametric formulations of material properties. Software development is required to develop good fluid flow analyses for large. 3D models to simulate filling of and convection in molds.Integrating this system of programs is difficult due to proprietary database structures used by software developers. However, an acceptable means has been accomplished' to move data from one program to another. Further software development is required to facilitate this task. INTRODUCTIONThe process of producing a new cast component requires significant design and development by both the design and foundry engineer. This effort strives to produce a high quality, reliable component at minimum cost in a timely manner. The design engineer needs to know the physical and mechanical properites which can be expected in the actual part at critical areas. This will enable him to design a part with minimum material while fulfilling the performance required. The foundry engineer needs to produce a sound, quality casting with a minimal amount of material In risers, the feeding system and machining stock. This must be done with a minimum· investment in tooling and development time and maximum productivity of labor and capital employed. This task Is continually being made more difficult because of increased competition in the marketplace and the use of castings in more severe service. This has strongly influenced the need for high quality castings.The task of developing a new casting is difficult for both the design and foundry engineer. To assist in this development, Deere & Company has been engaged in the development of an analysis system to simulate material processes. A major portion of this program involves simulation of the metal casting process. This analysis system has evolved into a package of computer programs which simulates casting solidification and subsequent cooling through the finite element method"

Jan 1, 1986

By Wenxian Zhu, Patrick R. Taylor

"The small dimensions of nano-sized materials leads to novel and enhanced mechanical and physical properties. A thermal plasma reactor has been developed to study the formation of nanometer sized metal powders. A supersonic nozzle and a powder filter were designed and built. By vaporizing coarse metal powders in the plasma flame, and quenching the metal vapors through the nozzle at the rate of 107 K/sec, nanometric sized powders have been produced. The powders were collected in an airtight secondary quench-filter system. The particle size of the product power is 5 -20 nanometers, obtained through TEM analysis. The XRD analysis showed that the powder did not oxidize after the filter was handled in an inert atmosphere glove box.IntroductionNanostructured materials have been shown to exhibit improved physical and mechanical properties compared to conventional materials with larger grain sizes (1,2). There have been several methods proposed for preparing nanometer size materials. Thermally induced vapor-phase reactions have been used to produce a variety of powders. A common feature of these processes is the rapid production and cooling of condensable reaction intermediates and products, by gas-phase reactions, leading to the formation of a large number of very small particles. Thermal plasma synthesis of ultra-fine size particles has been attracting increasing interest (3,4,9-11), because it offers many advantages, especially in refractory materials processing, compared to conventional processes: (a) thermal plasma temperatures are very high(> 5000 K); (b) the rates of chemical reaction are much faster than those encountered in conventional processes; (c) high-purity materials may be obtained using fewer processing steps by collecting the product at temperatures where the by-products are in the vapor phase; ( d) the mean particle diameter can be controlled; (e) unifom sized particles may be produced with clean surfaces (these particles are particularly suitable for pressureless sintering); and, (f) high throughput per reactor volume can be achieved. In addition, the process used for generating particles determines the degree of sintering ability of the powders, since the process dictates the morphologies, the purity and its size distribution. In the future, thermal plasma synthesis nanometer size particles may play an important role in vapor phase reaction techniques and might be expected to be one of the first full scale commercial installations in the future."

Jan 1, 1998