Search Documents

By Tetsuro Sakai

Home appliance recycling law was put into force in April 2001 in Japan. Specified kinds of home appliances, such as air conditioners, television sets, refrigerators and washing machines, should be recycled according to the law. Mitsubishi Materials Corporation (MMC) in cooperation with home appliance manufacturers is operating five home appliance recycling plants in Japan. MMC established complete treatment system of recyclable materials generating from home appliance recycling plants, which is formed by unique collaboration among home appliance recycling plants, copper smelter and refinery, and cement plants. Recyclable materials containing copper and precious metals are only handled and treated within the MMC group. By using this lock-in system, safe treatment and traceability of materials are guaranteed as 100% materials recycle.

Jan 1, 2008

By Huaming Yang

The vanadium-doped SnO2 nanoparticle was synthesized by the co-precipitation reaction and subsequent calcination from the vanadium(III) chloride and tin(IV) chloride. The crystal size, pore size distribution, micrograph and properties of the nanocrystalline powders were examined by differential thermal analysis (DTA), thermogravimetric analysis (TGA), X-ray diffraction (XRD), desorption isotherm (Barrett-Joyner-Halenda method) and transmission electron microscopy(TEM). Thermal treatment of the precipitate powder at 600°C led to the formation of V -SnO2 nanoparticle of -10mm in crystal size. Most of the pores in the nanoparticle are about 5~15nm in diameter. Effect of doped vanadium on the crystal size of the nanopartic1e was discussed.

Jan 1, 2003

By Huaming Yang

The vanadium-doped SnO2 nanoparticle was synthesized by the co-precipitation reaction and subsequent calcination from the vanadium(III) chloride and tin(IV) chloride. The crystal size, pore size distribution, micrograph and properties of the nanocrystalline powders were examined by differential thermal analysis (DTA). thermogravimetric analysis (TGA). X-ray diffraction (XRD), desorption isotherm (Barrett-Joyner-Halenda method) and transmission electron microscopy (TEM). Thermal treatment of the precipitate powder at 600'C led to the formation of crystal0nmincrystal size. Most of the pores in the narmparticle are about 5~15nm in diameter. Effect of doped vanadium on the crystal size of the nanoparticle was discussed.

Jan 1, 2003

By W. G. Davenport

Most pre-t 988 Outokumpu flash furnaces were built with blast heaters. Many continue to use them. Blast temperatures in these smelters· are typically 400 to 700 K (Table 2. 1) This chapter: (a) shows how hot blast is included in our calculations (b) evaluates the effects orhot blast onauthothermal65% Cu matte production.

Jan 1, 2001

By Xingming Zhang, Huawei Zhang, Yanxiang Li

"A hybrid porous metal with nano-micro double scale pore size and regular-random bimodal porous structure has been fabricated by unidirectional solidification of a lotus-type alloy followed by dealloying treatment to the base alloy. The base alloy selected is a Cu-Mn binary alloy. The lotus-type porous Cu-Mn alloy with straight pores of several hundred micrometers in diameter was manufactured by unidirectional solidification with a mould casting process. Dealloying treatment was then done to the lotus-type porous structure of Cu-Mn alloy. The solid Cu-Mn alloy wall of the lotus-type porous structure was transformed to random porous structure of dozens to hundreds nanometers. The influence of corrosion parameters, such as the current and time in electrochemical corrosion, temperature and corrosion agent in chemical corrosion, on the nano-porous structure formed has been studied systematically.1. IntroductionA hybrid porous metal is a kind of cellular structure with different porous or cellular forms inside, which possesses special properties and can be applied in many fields as fuel cells, catalysis, sensors, etc. Several means have been developed to fabricate this kind of porous material [1-2]. In this paper, a novel process of Gasar plus dealloying is introduced to fabricate a new form of hybrid porous metal with nano-micro double size and regular-random bimodal structure.The Gasar process, also called the metal-gas eutectic directional solidification, that invented by Shapovalov [3] in Ukraine and now in USA some twenty years ago, is used to fabricate porous metals with regularly aligned pores basing on the solubility difference of a gaseous element in solid and liquid metal. Nakajima and his colleagues [4] in Japan studied this process further and called this kind of structure a lotus-type porous metal. They put more attention to various fabrication techniques and properties of lotus-type porous metals. Li heading a group [5-6] in P.R. China studied the mechanism of Gasar process and process controlling techniques. The Gasar pore structure and porosity can be controlled by processing parameters, and a regular Gasar structure with oriented pores distributing uniformly in the solid matrix can be obtained under optimized processing parameters."

Jan 1, 2014

By T. S. Montgomery

The performance of carbon-magnesia brick in electric arc furnaces (EAF) is interpreted in light of their observed optical microstructures. Features at the bricks' hot faces were protruding periclase grains, metal globules, graphite-metal contacts and linear void patterns. These features were com-pared to similar features previously seen from microstructures of basic oxygen furnace (BOF) refractories. Modes of formation were sought; an attempt was made to interpret their influence related to wear mechanisms.

Jan 1, 1982

Mineralogical and metallurgical scoping testwork were carried out to investigate the production of separate, marketable gold and platinum concentrates. The study utilized a flotation concentrate assaying approximately 5 wt% gold and 5 grams per tonne platinum. The gold-platinum mineralization was recovered from a placer deposit. Optical microscopy and scanning electron microscopy with energy dispersive x-ray analysis identified gold as zoned Au- Ag and Au-Ag-Cu alloys. Platinum primarily occurred as weakly zoned, variably magnetic Pt- Pd-Fe alloys. A combination of gravity and magnetic separations resulted in a gold concentrate grading 86.9 wt% Au (and 9.lwt% Ag) and a separate platinum concentrate grading 400 g/t Pt with recoveries of 94.5% and 96.7%, respectively. Magnetohydrostatic separation (MHS) using the Magstream 200 Separator indicated promising results.

Jan 1, 1994

By Onuralp Yücel, Mehmet Bugdayc, Murat Alkan

"In this study, iron based alloys (Fe-Mo, Fe-Cr-Ni, etc.) were produced by using aluminothermic methods starting from Mill Scales obtained continuous casting processes. Mill scales are an oxidised layer of steel alloys containing iron oxide, which includes + 2, + 3 values, on the surface of slabs and billets occurring during annealing in heating furnace at integrated iron and steel milling plant, and continuous casting unit. In the metallothermic experiments, different ratios of starting mixtures and addition of the oxide powders (Alz03, Si02, CaO, MgO) were examined, and their effects on the metal recovery and alloy compositions were carried out. The samples were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques.IntroductionSelf Propagating High Temperature Synthesis process (SHS) has many favour compared to the furnace applications, such as low energy requirement, low cost, very short processing time and simple operation, [l, 2]. In a SHS process, the ignition starts the combustion and propagates throughout the reactant mixture yielding the desired product. However, the disadvantages of the process such as inhomogeneous or unreacted products due to undesirable reaction rates needs to be overcome by changing some parameters such as ignition temperature, particle size, additive, atmosphere etc. [3, 4]. Mill scale is a layer of iron oxide which forms on ferrous materials cooling after being processed in hot rolling or continuous casting plants. Mill scale contains iron (II) and iron (III) oxides, which result in a 70% total iron content in oxide form. Not being able to reuse this material will prevent the raw material entering the production plant from being fully utilized [5]. This study aimed to produce Fe-based alloys via SHS (Self Propagating High Temperature Synthesis) metallurgy which is attractive process technique regarding fast and low-cost production ability of cast alloys by using high metallic iron content by reducing continuous casting mill scale."

Jan 1, 2013

By Jinfu Xu, Youqing Cao, Yuting Lv, Hang You, Peng Jiang

"In present work, we reported the fabrication of composites consisted of M42 powder metallurgy high speed steel and 45 steel at one step via spark plasma sintering (SPS) technology. The interface microstructure, compositions and microhardness with the interface forming mechanism were investigated. The results show that the morphology and microhardness within the M42/45 steel interfaces exhibit a gradient distribution. The interfaces possessed a transition layer up to 10.2 ?m with few distortions and microcracks. The formation of M42/45 steel interfaces were driven by both fusion and diffusion processes. The former one was primary at the early sintering process, while the later one becomes dominant over the followed sintering process.IntroductionPowder high-speed steels have been widely used in cutting tools, cold-hot tools and dies, as well as in cut materials and structure parts with wear resistance and high-temperature resistance, due to its high hardness, good wear resistance, desirable cutting toughness and favorable hot hardness [1-2]. For materials of some parts in practical production, not only the favorable toughness is required to resist the impact action, but also the high hardness and exceptional wear resistance are demanded. According to the functional requirements and working conditions, bimetal composite materials are prepared in a certain mode, proportion and distribution, by designing two metals with different chemical and physical properties [3-6]. Considering the composites exhibit different properties in different positions of the parts with a combination of the advantages of two metals, they can obtain enhanced properties that the single one can not achieve."

Jan 1, 2012

By Geza Kisvarsanyi

Ore deposits composed of enargite, tennantite, gold, and pyrite have been mined in volcanic rocks of Oligocene age (35 m.y.) at Recsk, Hungary. Vertical and horizontal zoning of the alunitic-argillic alteration and of the ore minerals led to the concept of an intrusive heat source at depth. Subse-quent drilling disclosed a series of ore deposits in a zoned pattern in and around a stock, separated by a barren gap of 1000 meters from the shallow ore. The ore system is in a intracaldera horst-graben structure, formed by collapse and intrusion in a microplate subduction. volcanic-arc tectonic environment.

Jan 1, 1987

By M. Sizgoric

Certain types of mineralogical alteration due either to weathering or serpentinization, and the effects these transformations have on the flotation of nickel sulfide ores are discussed. These effects are generally deleterious due to: (a) the poor flotation properties of the alteration minerals (as in the case of tochilinite), (b) the nature of the alteration texture (as in the case of violarite), or (c) .close association of the alteration products with other undesirable minerals (such as nickeliferous smythite). Several examples from INCO Metals Company's mines and mineral prospects are given as illustration.

Jan 1, 1981

By Baozhong Ma, Qian Li, Yonggang Wei, Shiwei Zhou, Bo Li, Chengyan Wang, Hua Wang

The magnesium-rich nickel oxide ore (w (Ni) =1.09 %, w (MgO)=29.08 %) mixed with 6 % and 8 % anthracite were roasted at different temperatures. XRD and SEM/EDS techniques were utilized to characterize the phase and microstructure transformation of the ores. The results show that lizardite and chrysotile of raw ore were converted into forsterite and enstatite during reduction roasting process. Simultaneously, iron and nickel oxide were reduced and migrated from the initial magnesium silicate. Fe3Si were formed when the roasting temperature went up to 1300 ℃ and 1350 ℃, and a small amount of Ni was observed in it. Temperatures got too high were not benefit to the polymerization of ferronickel.

Jan 1, 2015

By Run Huang, Xuewei Lv, Songli Liu, Chenguang Bai

"Titanium alloy was prepared from titania-bearing blast furnace slag (Ti-BF slag) by aluminothermic process in an induction furnace. The effects of aluminum amount on the titanium silicon yield and titanium recovery ratio were studied. The phase transformation and chemical composition of the prepared alloy were investigated by X-ray diffractometry (XRD) and X-ray fluorescence (XRF) respectively. It was found that the mass fraction of silicon and aluminum increased with increasing the aluminum amount, however, the mass fraction of titanium increased first and then decreased with increasing the aluminum amount. Furthermore, both the titanium alloy yield and titanium recovery ratio increased with the increase of aluminum amount. The main phases of the alloy were TixSiy and AlTi3. The titanium alloy samples prepared in various conditions had a composition (wt.%): 38–50% Ti, 29-34% Si, 4-11 Al%, 1.6-2.2 Mn%.IntroductionPanzhihua and Xichang regions in the southwest of China are rich in vanadium-titanium magnetite containing iron, vanadium, titanium and gangue. According to the characteristics of the resource, iron and vanadium are successfully recovered with a blast furnace process and a converter process. However, most content of titanium are entered in the blast furnace slag with TiO2 22% -26% and metallic Fe 2%–6% called Ti-BF slag. Due to the dispersed distribution of Ti in various fine grained mineral phases with a complex combination between Ca, Al and Si, it is difficult to recover the Ti components[1]. This slag is generated at a current rate of 3.6 million tons per year, which adds to the existing 70 million tons of slag produced so far[2]. The slag has had to be piled as large as the mountains, which not only waste of resources but also cause a pollution of the environment. Therefore, the study of integrated utilizing Ti-BF slag has become very significant."

Jan 1, 2012

By Daojin Cao

Aiming at many controversial reports on Raman spectral pattern of heptamolybdate ion in aqueous solution appearing in the literature and the absence of its standard pattern, the comparative investigations on Raman spectral pattern of saturated solution of ammonium heptamolybdate tetra hydrate were done. The results showed that the main vibrant frequencies of Raman spectral pattern of the saturated solution were in good agreement with those introduced in the literature, and that the intensity ratio (4.4) of the strongest peak to the second strongest peak recorded in Raman spectrum of the saturated solution had three obvious characteristics: it was greater than each of the results (ranging from 3.7 to 1.3) reported in the literature, much closer to that (4.7) of crystal and well conformed to the change rule of Raman spectra occurring in the process of the first-step polymerization of acidified molybdate solution. It was found that Raman spectrum of heptamolybdate ion in aqueous solution was determined by not only the main vibrant frequencies but also the intensity ratio, which is also the crucial result in this study. The comparative investigations indicate that the pattern of Raman spectrum of the saturated solution is the standard pattern of Raman spectrum of heptamolybdate ion in aqueous solution essentially. The affirmed standard pattern is reliable and can be used to the identification of heptamolybdate ion in aqueous solution, applied in the research of the equilibrium of acidified molybdate solution and the exploration of the best technologic condition for the production of high quality heptamolybdates.

Jan 1, 2006

By Pradeep kumar Jha, Manas Mohan Mahapatra, Sabin Kumar Mishra, Satish Kumar Ajmani, Satish C. Sharma

"Due to mechanical/ electrical failure in the C.C. line or inadequate availability of molten steel from coming ladle, sometimes one/two outlets of a multi-strand tundish in continuous casting unit is closed. Closing any of the outlets affects the flow distribution inside the tundish which in turn governs the quality of steel coming out. Hence it is important to study which of the outlets should be closed to have proper results in terms of flow behavior and inclusion removal inside the tundish. Present study aims at finding the effect of closing one or two outlets on flow behavior and inclusion removal in a multi strand tundish. It was found that closing the near outlet (outlet near to the inlet) increases the inclusion removal tendency than closing the other two outlets in a six-strand billet caster tundish (only three outlets are considered because of symmetry).IntroductionContinuous casting process transforms molten metal into solid on a continuous basis. This process is the most efficient way to solidify large volumes of metal into simple shapes for subsequent processing [1]. Molten metal is tapped into the ladle from furnaces. From the ladle, the hot metal is transferred via a refractory shroud (pipe) to a holding bath called a tundish. The tundish allows a reservoir of metal to feed the casting machine while ladles are switched, thus acting as a buffer of hot metal as well as smoothing out flow, regulating metal feed to the moulds and cleaning the metal [2]."

Jan 1, 2012

By M. Radwan

This research reports on the synthesis of advanced silicon-based structural ceramics from mixtures composed of natural sand (Sinai white sand), reclaimed silicon and graphite by the nitriding combustion synthesis method. With pulverized sand (? 40 m), we found that the nitriding combustion can be realized at self-sustaining mode in the SiO2?Si?C system under 3 MPa nitrogen pressure. Depending on the composition of the starting mixtures, single-phase silicon oxynitride (Si2N2O) powder as well as new Si3N4?Si2N2O and Si2N2O?SiC composite powders with controllable chemical compositions were successfully developed. The measured thermograms of various combusted mixtures and the thermodynamic characteristics of possible exothermic reactions in this system were discussed to explain the nitriding combustion behaviour and mechanism. Near-full dense Si2N2O were fabricated from synthesized Si2N2O powder with 5 wt % oxide additive by the spark plasma sintering (SPS) method at 1600 °C. The dense Si2N2O samples had good mechanical properties (18.7 GPa Vickers hardness, 3.3 MPa m1/2 fracture toughness and 363 MPa strength) and excellent chemical and oxidation resistance. The synthesized composite powders were also densified to high densities (> 90 % of theoretical values) by SPS technique. The results obtained in this study can be seen as a new route to prepare important silicon-based structural ceramic powders with various compositions/properties from cheap starting materials which makes them potential for wide range of applications.

Jan 1, 2006

By Peng Peng, Ouo Cheng, Guodong Lai, Lijuan Chu, Zebiao Zhang

"The pressure acid leaching residue of zinc concentrate contains a large quantity of sulfur. The present study attempts to leach sulfur using a mixture of ammonium sulfide and water solution at 25°C. Effects of three leaching variables: ammonium sulfide concentration, leaching time, liquid/solid ratio on the sulfur leaching rate were investigated. The process conditions were optimized using response surface methodology based on the central composite design. From the analysis of variance (ANOVA), the significant factors on response were identified. The optimum conditions for leaching elemental sulfur from pressure acid leaching residue of zinc concentrate were obtained using an ammonium sulfide concentration of 2.5 mol/L, leaching liquid-solid ratio of 6.5:1 and leaching time of 7 min. Under the optimum experimental conditions, a maximum of 98.50% of total sulfur was extracted. The experimental results obtained agreed satisfactorily with the model predictions, with a correlation coefficient (R2) of 0.99.IntroductionSulfur is widely used in agriculture, medicine, rubber, building materials, gunpowder, wine and sugar, and other fields [1]. Currently the world sulfur production is 40Mt, out of which more than 90% is recovered from industrial processes, and 10% is natural [2], This highlights the importance of sulfur recovery. As the pressure leaching technologies [3] continue to mature and are increasingly applied to refining, a large quantity of high-sulfur residue is produced [4-5]. It is desirable to recover sulfur from this residue, so that it is economically advantageous, and reduces environmental pollution [6]."

Jan 1, 2012

By Shadia J. Ikhmayies

"Cadmium sulfide thin films were prepared on glass substrates by the spray pyrolysis technique at a substrate temperature of 490°C. Some of the films were etched by HC1 in distilled water, others were heat treated in nitrogen atmosphere, and another set of films was first etched by HC1 and then annealed. Room temperature impedance spectroscopy measurements on the films were performed using coplanar geometry in the dark and in room light in the frequency range 20 Hz to 1 MHz. The experimental data were represented by complex plane diagrams and showed one well-defined semicircle in the high frequency region. Hence the equivalent circuit that models the CdS: In thin films was found to be a single RC circuit, which indicates the bulk conduction through the grains. The influence of treatments on the electrical properties was investigated.IntroductionCadmium sulfide (CdS) is a brilliant II—VI semiconductor material with a direct band gap of 2.42 eV at room temperature. It has many outstanding physical and chemical properties, which have promising applications in multiple technical fields including photochemical catalysis, gas sensor, detectors for laser and infrared, solar cells, nonlinear optical materials, various luminescence devices, optoelectronic devices and so on [1]. There are different methods to prepare undoped and doped CdS films, such as rf sputtering [2] chemical bath deposition (CBD) [3], pulsed laser deposition (PLD) [4], and spray pyrolysis (SP) [5-11]. Of these methods, spray pyrolysis represents the less expensive option, and can produce large area high-quality low cost thin films [12]."

Jan 1, 2012

By M. E. Ramos Rada

Mexicana de Cobre, which is part of Grupo Mexico, carried out studies for the construction of a copper refinery in the La Caridad Metallurgical Complex located in Nacozari, in the state of Sonora, Mexico. After the studies were concluded, the decision was made to construct a 180,000 t/y refinery using the state of the art permanent cathode Kidd Process. The basic engineering was developed by Fluor Daniel and the detail engineering and the construction were carried out in record time by the Mexican company Bufete Industrial. During the construction phase, Grupo Mexico decided to expand the refinery, and actions were taken to increase its capacity by an additional 120,000 t/y; the final result was a refinery capable of producing 300,000 tonnes of grade A cathode per year. Construction began in January 1996, and the operation of the first stage began on July 1, 1997. The operation of the second stage commenced on January 7, 1998. The capacity of the first stage was reached in November, 1997 and the total capacity of the refinery was achieved in May, 1998. This presentation describes the process and equipment installed in the refinery, the steps leading to the start-up, the operation and the results obtained during the first two years, the handling of anodes with high impurity contents, and the problems confronted and the way they have been solved. It also includes personnel productivity, the control parameters and the most relevant data on the operation of the process.

Jan 1, 1999

By F. Begazo

The most common approach to increase production in copper refineries is to increase current densities. However, if these increases are not well thought out beforehand and are not properly and effectively controlled, the end results could be reduced plant performance and a deterioration in cathode quality. Both of these factors result in lower efficiencies and increased costs. At the Ilo Refinery of Southern Peru Copper Corporation, a modernization and expansion program was implemented shortly after the Refinery was purchased from Minero Peru, in 1994. This program was intended to increase production from 195,200 mtpy of cathode to 227,000 mtpy over a 3-year period. Part of this production increase would come from increasing current density. During the period from 1994 to 1997, current density at the Ilo Refinery was increased from 218 A/m2 to 230 A/m2, while plant efficiencies were maintained at consistently high levels. The current efficiencies were maintained at >97.5% and time efficiencies were maintained at >98%. During 1998, additional increases in current density were implemented while the high plant performance was maintained at the same levels. By the end of 1998, the current density was 241 A/m2, while current efficiency and time efficiency of 98% were maintained. This paper describes the control processes used at the Ilo Refinery to maintain high plant performance levels while increasing the current density. Additionally, expected plant performances from extended test programs at current densities up to 280 A/m2, for future production increases, are reviewed and discussed.

Jan 1, 1999