Search Documents

By P. D. Lee

The effect of strontium on porosity formation in aluminum-silicon alloys is not well understood and there is no consensus upon the cause of the effects observed. This paper describes a series of experiments where the effect of adding strontium on pore formation was observed directly with combination of a traditional temperature gradient stage and real time micro-focus radiography. These in situ observations provide a new insight into the effect of strontium on the nucleation and growth kinetics of porosity. The addition of strontium was found to have a minor effect on the growth of the pores in the mushy zone. However, strontium appeared to alter the nucleation and stability of hydrogen bubbles within the melt. The interaction of strontium with titanium-boride grain refiners produced an even stronger change in the nucleation and stability of the bubbles formed.

Jan 1, 2002

By Hu Long

Pyrite, as the host mineral in refractory gold ores and concentrates, has been treated by pressure oxidation in sulfuric acid solutions at temperatures above 180°C to liberate gold prior to cyanidation since the 1980's. However, no data is available on the kinetics of pyrite during acid pressure oxidation over the temperature range of 180 to 230°C which is the range employed by most commercial plants. The dissolution of pyrite (FeS,) in sulfuric acid solution under oxygen pressure was investigated at temperatures ranging from 170 to 230°C. The effects of temperature, particle size, agitation speed, oxygen partial pressure, and pulp density were evaluated. The effects of foreign ion addition and the concentration of sulfuric acid were also examined. The apparent activation energy was estimated to be 42.6 kJ/mol in the temperature range 170 to 230°C. The reaction orders with respect to particle size and oxygen partial pressure were found to be -1.5 and 0.5 at 210°C, respectively. Experimental evidence suggests that the kinetics are limited by the surface chemical reaction initially, and then also to some extent by the diffusion of ferrous ions away from the particle surface.

Jan 1, 1999

By V. D. Tathavadkar

Chromite ore is of immense importance for the extraction of metallic chromium and chromium chemicals. The mineralogy and crystal structure of chromite phase are therefore important part of our investigation on the extraction chemistry of chromium species. In this investigation, we have studied the effect of the processing parameters, i.e., the temperature and the oxygen potential on the microstructure and composition of mineral phases formed in the Cr2O3 ?Al2O3 -FexOy -MgO system. In particular the importance of the spinodal decomposition reaction is emphasized in the extraction of chromium as sodium chromite and sodium chromate. Experiments were carried out in order to study the differences in the crystallography of different chromite minerals. Phase equilibria in natural chromite minerals were investigated by calcining chromite mineral in air, argon, and 5% hydrogen + argon atmospheres over a temperature range from 200 to 1200 °C. The effect of the oxygen partial pressure and temperature on the phase constituents of the calcined product has been discussed. The microstructural changes were examined using scanning electron microscope (SEM) and the changes in elemental composition in different phases were analysed by electron probe micro analyser (EPMA). The results obtained from EPMA studies were used to calculate lattice parameter of the spinel lattice, and these values were compared with the values obtained from X-Ray powder diffraction data. On the basis of the experimental data, the mechanism of the spinodal decomposition of complex spinel phases is described under the influence of oxygen partial pressure and temperature.

Jan 1, 2000

By Leizhang Gao, Zhengfeng Qu, Pingsheng Lai, Chenguang Bai, Meilong Hu

FFC process could be used to prepare titanium foams. The mixed oxides CaO-TiO2 with mole ratio 1:2 were sintered into CaTiO3-TiO2 mixture. CaTiO3-TiO2 was then used as cathode and electrolyzed in molten CaCl2 to prepare porous titanium. The porous titanium with the porosity of about 72.15% was first fabricated. The internal pores are in the presence of circular cavities and the pore size is in the range of 50–100 lm. Compared with the powder metallurgy technique using the space-holder this method promises to be lower cost and less processing. It is potential to fabricate titanium foams using FFC process.

Mar 1, 2018

By R. S. Celmer

The distributions of cobalt, molybdenum, copper, and selenium between nickel matte and silica-saturated iron silicate slag have been determined in the region of the metallic saturation boundary, at 1523 K. Results are given as a function of the composition of the coexisting Fe-Ni alloy and the activity of iron in the system. Under strongly reducing conditions, these minor elements display a marked preferential accumulation in the sulphide phase. It is shown that the dissolution of cobalt and molybdenum in slag follows an oxidative mechanism, and distribution equilibria are correlated with the oxygen potential. From these data, the thermodynamic properties of cobalt in nickel matte are computed. Further, comparisons of minor element partitions are made between the nickel and copper matte smelting cases under metal saturation conditions.

Jan 1, 1988

By Atsushi Shibayama

The aim of this research was to develop a copper recovery process from mine tailings (0.34%Cu) using flotation followed by high-pressure oxidative leaching (HPOL) and solvent extraction. The results of HPOL using the concentrate of mine tailings obtained by flotation under the optimal conditions of the previous study shown that an efficient copper dissolution of 94.4% was achieved in an H2O media, while the copper concentration of PLS reached to be 2.9 g/L. The solvent extraction of PLS obtained from the optimal HPOL showed that 91.3% copper was recovered in stripped solution under the determined optimum conditions, in which the copper concentration achieved to be 44.8 g/L. Finally, a proposed copper recovery process from the concentrate of mine tailings was developed by combination of HPOL and solvent extraction, while a total copper recovery of 86% was achieved.

By G. Brooks, J. Naser, M. A. Sattar

CFD models have been developed and numerical simulations have been carried out to predict the formation of foam in oxygen steelmaking. Foam was considered as a separate phase comprising a mixture of gas and liquid. Bubble break up and coalescence models have also been incorporated in a CFD model to predict the number density of individual bubble classes. A population balance equation was used to track the number density of each bubble class. Decarburization with heat generation from chemical reactions was integrated in the process. User subroutines were written in FORTRAN to incorporate the foam formation, the bubble break up and coalescence rate and decarburisation in the main program. The model predicted the foam height, bubble number density, velocity of phases, decarburization, and turbulence. The result from the model has been compared with available data from literature and found to be in reasonable agreement with the experimental and plant data.

Jan 1, 2014

By Xuan Cheng

The electrochemistry of sulfide mineral flotation is reviewed with particular emphasis on galvanic interaction among minerals and grinding media, and its relevance to flotation of complex sulfide ores is discussed. Surface alteration due to galvanic interactions among chalcopyrite, pyrrhotite and mild steel is analyzed in terms of voltammetric and chronoamperometric studies on individual minerals and through galvanic current measurements in 2- and 3- electrode combinations. The results are related to laboratory flotation behaviors of chalcopyrite-pyrrhotite mixtures simulating copper-nickel bearing Duluth gabbro.

Jan 1, 1993

By P. T. Velu

Solubility of metal oxides in the molten salt electrblytes is an important parameter in the electrochemical processing of metals and alloys. The efficiency of an electrochemical process primarily depends on the quantity of metal oxide present in the electrolyte in the dissolved form and its thermodynamic properties. The activity of CeO2 was calculated using the free energy of fusion of CeO2,{ AG°m, CeO2. The AGOm,CeO2 }was deduced from the values of enthalpy, heat of fusion and melting point of Ce02. The activity coefficients of CeO2 as a function of temperature and melt composition were calculated. The thermodynamic data such as integral molar enthalpy, entropy and Gibbs energy of formation were calculated as a function of composition and temperature.

Jan 1, 1994

By Shadia J. Ikhmayies

In this work the equilibrium temperature-composition phase diagrams of the Si-O2 system were calculated using Thermo-Calc software in the temperature range 500–3000 K. Constituents of stable phases were obtained, and the amounts of certain phases where investigated with the variations in the composition of oxygen and temperature. It is found that quartz with silicon represent a stable phase in the temperature range 500–1150 K, while tridymite with silicon represent a stable phase in the temperature range 1150–1700 K. A liquid phase is found besides tridymite in the temperature range 1700–1750 K, and a stable phase of cristobalite with liquid appears in the temperature range 1750–2000. The maximum amounts of quartz, tridymite, and cristobalite are found at oxygen mole percent of 67.7%.

Mar 1, 2017

By Toshia Ishii, Jun Kubota, Noriko Kubo

"For steel continuous castings, it is essential to control molten steel velocity at the meniscus, since the velocity is closely related to surface defects on the resultant products. Argon gas is supplied with molten steel into the mold through the submerged entry nozzle to prevent nozzle clogging. In this study, to investigate the influence of argon gas on molten steel flow, a numerical simulation was carried out by a two-phase model. Simulation results indicate that as argon gas bubbles ascend near the nozzle by their buoyancy, they induce the molten steel flow with them and resulted a meniscus molten steel flow from the nozzle to the narrow face of the mold. This flow direction is opposite to the case without argon gas. The calculated data are compared with the experimental data. The comparison shows generally good agreement between the measured and the calculated data. IntroductionIn a steelmaking process, molten steel carried by a ladle is first fed into a buffer vessel called tundish. From the tundish, it is then fed into a continuous casting mold. Molten steel solidifies gradually in the mold (the primary cooling zone) forming a solidified shell. As the solidified shell is just thick enough to support the molten steel at the mold exit, it is withdrawn through the mold by pinch rolls. It is progressively thicken as it is further cooled with water sprays in the secondary cooling zone. At the end of guide roll zone, completely solidified steel is cut into desirable lengths. Schematic view of a typical continuous casting is shown in Figure 1."

Jan 1, 1999

By Alexandra Anderson

A computational fluid dynamic (CFD) model has been developed using ANSYS Fluent 17.0 to help identify areas of high wear within the refractory lining of a secondary lead reverberatory furnace. Once a base case simulation was validated using data from an operational furnace, areas of potentially high refractory wear were determined through the calculation of the temperature and velocity distributions within the furnace and on the hot face of the refractory lining. The CFD model was used to assess whether the predicted areas of high refractory wear could be minimized through changes burden geometry. The results showed that shape of the burden geometry greatly affected the overall flow patterns and heat transfer within the furnace.

By I. Moscoso, R. Padilla, M. C. Ruiz

Antimony and arsenic are impurities in copper concentrates found normally as stibnite (Sb2S3), tetrahedrite (Cu12Sb4S13) and enargite (Cu3AsS4). When copper concentrates contain appreciable amounts of As and Sb, they must be removed before smelting to avoid environmental pollution. Oxidizing volatilization roasting at 500–700 °C has been used to eliminate these impurities. However, only a fraction of Sb volatilizes in those conditions; thus, a more effective process to eliminate antimony from concentrates is needed. In this study, the chloridizing roasting of Sb2S3 using CaCl2–O2 was investigated to remove the antimony from concentrates. XRD analysis of calcines indicated that the overall reaction could be written as: Sb2S3 þ3CaCl2 þ6O2 ¼ 2SbCl3 þ3CaSO4 Temperature and oxygen partial pressure have a significant effect on the rate of reaction. An estimated conversion of about 90% was obtained at 750 °C, 5.4% oxygen in 20 min. High oxygen concentrations arrest the advance of the reaction forming various antimony oxides including Sb6O13, Ca5Sb5O17 and Sb2O4.

Mar 1, 2017

By A. E. Clark

Rare earth compounds are widely known as possessing many extraordinary magnetic properties. In this paper, we focus on the huge magnetically induced displacements (magnetostrictions) which characterize the compounds of terbium with iron (Terfenol). Materials prepared commercially by both free-standing-zone (FSZ) and modified Bridgman (MB) techniques have now become available in large sizes and shapes. Prior to the development of the Terfenol alloys, it was possible to achieve giant magnetostrictions only at cryogenic temperatures. In the cubic Laves phase TbFe2 compound, saturation strains exceed 3000 x 10-6 at room temperature and above. Large magnetization 'jumps' can occur, causing huge spontaneous magnetostrictions with small triggering magnetic fields.

Jan 1, 1992

The results of laboratory, large-scale laboratory and commercial scale investigations regarding the process of slag melts cleaning by oxidizing-reduction gas mixtures with a wide range of Po2 and the use of matte of various compositions as an extracting phase are presented. The copper, nickel and cobalt behavior during the cleaning process has been studied based on SEM and x-ray Microprobe of the quenched slag melts. The general cleaning mechanisms have been found. On the basis of the obtained data the most efficient cleaning methods have been proposed.

Jan 1, 2003

By D. A. Salinas G., A. H. Castillejos E.

Pachuca tanks are commonly used in the hydrometallurgical industry to carry out leaching operations. The fluidynamic characteristics of the liquid phase, resulting from the injection of gas into the draft tube, are important to achieve the complete suspension of the mineral particles and has a decisive influence in the mass transfer processes occurring in this reactor. This study investigated the effect of different design and operating characteristics on the liquid velocity field. using a laboratory-scale Pachuca tank. The transparent model was filled with water, and air was injected through the bottom in the absence of mineral particles. The liquid velocities over the whole reactor were measured under several experimental conditions using particle image velocimetry (PIV). This technique allowed to obtain a very detailed picture of the liquid motion even in the draft tube, as long as bubbles were absent from the measured field of view. The experiments have shown that the liquid velocities increase with increasing the draft tube to tank diameters ratio, the distance from the conical bottom to the draft tube entrance, or the gas superficial velocity. On the other hand, an increase in the water level with respect to the draft tube outlet caused a decrease. A mathematical model, which used the no-slip model, to calculate the variation of axial effective density along the two-phase region, was found to predict liquid velocity fields which agree very satisfactory with the experimental results obtained under all the conditions studied.

Jan 1, 1999

By Richard D. Hagni

An enhanced Interest in pyrometallurgical dusts has recently emerged due to increased world-wide environmental concerns. Mineralogical study of dusts samples from lead sinter plants. lead smelters, and secondary steel mill electric arc furnaces has shown that they can be readily studied by reflected light microscopy. These dusts typically are composed of small particles sufficiently large that their mineralogical identification and characterization can be conducted under the reflecting light microscope. Scanning electron microscope-energy dispersive spectroscopic analysis (SEM-EDS) has been used to confirm optical identifications and chemical compositions. The sinter and blast furnace dusts at the Doe Run Smelter at Herculaneum, Missouri are commonly about 20-150 11m. They consist predominantly of galena, chalcopyrite, sinter. slag. coke. and particles. Dusts from remote sampling sites 112-1 mile from the lead smelter are composed of similar particles and abundant fine-grained particles, less than 10 um. of locally derived calcium-aluminum silicates. Electric arc furnace (EAF) dusts are mostly spherical and less than 10 11m. They consist predominantly of iron oxides (magnetite. franklinite. jacobsite and solid solutions of these spinels), zincite. and calcium-iron silicate glass, together with smaller amounts of hematite. sylvite. coke and metallic iron. Reflected light microscopy is rapid provides mineralogical data on individual grains within dust particles. and allows direct observations of textural intergrowths in pyrometallurgical dust particles.

Jan 1, 1991

By T. T. Chen

Gold in the Twin Creeks ore is primarily associated with arsenian pyrite. During pressure oxidation, the sulphides are solubilized, but part of the dissolved iron reprecipitates as jarosite and as an iron sulphate-arsenate-phosphate phase. The pressure oxidation products are subjected to cyanide leaching. The cyanide leach residues consist of quartz, gypsum, bassanite, anhydrite, small amounts of jarosite, an iron-sulphate-arsenate-phosphate phase, as well as trace amounts of orthoclase, rutile, pyrite, hematite and monazite; all these particles are dispersed in a fine grained matrix of illite-muscovite. The autoclave leach residues contain a small amount of carbonaceous matter. Many gold grains are detected on the surfaces of the carbon particles, and these gold particles are not leached during cyanidation. The gold particles are typically 0.1-0.2/Lm in size and commonly are embedded in the carbon surface or are coated with a K-AI-Si-S-O phase on the surface of the carbon. The gold grains are consistently associated with elevated CI contents (50-300 ppm Cl). The poor gold cyanide leach recoveries, which initially occurred in the Twin Creek developmental circuit under certain operating conditions, are attributed to the presence of chloride in the feed. This results in the formation of soluble gold chlorocomplexes in the autolcave and the subsequent sequestering of the gold on the surfaces of the carbon particles.

Jan 1, 2000

By P. R. Taylor

Titanium carbide and titanium diboride powders have been successfully synthesized by direct treatment of ilmenite concentrates in a non-transferred arc thermal plasma reactor. Methane gas was used as the reducing agent and boron oxide was used as the boron source in these processes. Free energy minimization plots were used to predict the behavior of each system under different molar ratios and operating conditions. Products were characterized by XRD, SEM and chemical analytical techniques. The average size of the ceramic product is in the submicron range. Metallic iron apparently is finely deposited on the surface of the titanium carbide or titanium diboride particles. Minor impurities such as silica, manganese and zircon were converted to the carbide form.

Jan 1, 1995

By Manoj Kumar, Vinay Kumar, Nikhil Dhawan, Manish Wadhwa

"Electronic waste (e-waste) is a collective name given to discarded electronic devices such as Television, Cellular Phones and Personal Computers. Among the heterogeneous metals present in the e-waste are the base metals: copper, aluminium, nickel, tin, zinc, iron and precious metals: gold, silver, palladium, platinum apart from several hazardous and halogens metals. Hence there is a need to recover these metals from electronic scrap by recycling and then re-use, which can meet large amount of metals demand. Hydrometallurgical processing was employed for the recovery of metals from television printed circuit board (TV PCB). Different lixiviants such as hydrochloric acid, Sulphuric acid, and nitric acid were used to understand the dissolution behavior of copper, iron and lead present in the TV PCB. Effect of increasing concentration of nitric acid was also studied. Selective recovery of tin over 95% in the form of tin oxide was precipitated. The precipitated tin oxide was identified by X-ray diffraction technique. Tin oxide of purity more than 99.9% was obtained.IntroductionThe electrical and electronic industries comprising computers, television, mobiles, etc, which are manufactured utilizing printed circuit, boards, capacitors, resistance, soldering material etc. During production, at the end-of service life and degradation due to the advanced version with latest features generate valuable metallic and non-metallic constituents. European Union Council on waste electrical and electronic equipment (WEEE) has classified these into different categories as listed in Table 1 [Streicher-Porte et al., 2005]. Among these the information technology, telecommunications and consumer equipment constitute electronic waste (e-waste) [EC, 2002]. Almost all e-waste consists of an integrated part of printed circuit boards which is a valuable source of several metals such as copper, tin, lead, aluminium, iron, silver, gold, platinum etc. [Relay et al., 1990]."

Jan 1, 2008