Search Documents

By Hector Carreon

During fretting, high points or asperities of the mating surfaces adhere to each other and small particles are pulled out, leaving minute, shallow pits and powdery debris. Sometimes these surface conditions are neglected, but they are important in some application such as the aerospace industry. In this research work, non-contacting and contacting thermoelectric power techniques are performed in fretted 7075-T6 and Ti-6Al-4V samples. It has been found that the contacting and non-contacting thermoelectric power measurements are associated directly with the subtle material variations such as work hardening and residual stresses due to plastic deformation produced in the fretting zone but surface topography. Therefore, both techniques could be used for a global characterization of the most relevant fretting induced effects. Potential of these techniques to monitor subsurface changes in other severe surface plastic deformation processes are clearly envisaged.

Jan 1, 2015

By Khandaker M. Anwar Hossain

This paper presents the development of lightweight concrete (LWC) incorporating pumice aggregate and volcanic ash (VA) based ASTM Type I blended cement (PVAC). Fresh and mechanical properties of LWC mixtures such as slump, air content, compressive strength, tensile strength, density and modulus of elasticity are described. The durability characteristics are investigated by drying shrinkage (DS) and water permeability. The investigation suggests the production of LWCs incorporating blended PVAC and VPA having satisfactory strength/durability characteristics for structural applications. The use of PVAC induces the beneficial effect of reducing drying shrinkage and water permeability. Development of such non- expensive and environmentally friendly LWCs with acceptable strength and durability characteristics is extremely helpful for the sustainable development and rehabilitation of volcanic disaster areas around the world.

Jan 1, 2010

By Marcela Morvová, Mário Janda, Morva Imrich

"The possibilities of greenhouse gas mitigation using various methods are brought out. The special case of utilization of mixture of CO2 with other greenhouse gases in a synergetic way inside non-thermal plasma based system is described in detail.Measurements on pilot system comprising pyrolysis chamber as alternative energy system (production of hydrogen and liquid tar) were made for various biomass and waste as the input material. The exhaust from this system was treated with non-thermal plasma gap suitable for up to 650Nm3/hour of exhaust gas flow. Condensable portion of exhaust is liquefied in distillation unit; produced hydrogen is stored on-line inside nano sized carbon of our own production.The CO2 removal efficiency varies depending on exhaust composition between 45 to 98%. Other oxides as CO, NOx, SOx and several hydrocarbons and VOC are also removed. The main product connected with CO2 removal is a solid powder of proteinoid nature. There exist strong probability, that precursor of the origin of life on the Earth from primary atmosphere were formed in the similar way as it is present in the electric discharge system used. Our system is equipped with on-line as well as ex-post analysis of all forms of products. We have also developed a system for recuperation of all forms of produced heat. It is stored inside as latent heat of waxes.IntroductionNatural greenhouse effect on the Earth is caused mainly by water vapour with the average absolute concentration about 4%. Other gases able to absorb long-wave radiation and thus this causing greenhouse effect are CO2, CH4, N2O, halocarbons and as precursors ozone and NOX. Some of them we produce and introduce into atmosphere in large quantities during production of energy and in transport. This factor leads to permanent increase of average temperature of air, sea and oceans, so called global warming.Nowadays large amount of data exists showing that the temperature of Earth in the last 150 years has been continually increasing. It represents about 03°C per ten years and the most of climatologist believe, that the increased concentration of greenhouse gases in the atmosphere is responsible for this effect.The most important greenhouse gas is carbon dioxide CO2. Majority of CO2 emissions comes from electric power stations working with fossil fuels, cars and industry. Burning of fossil fuels contribute up to 80% to world wide anthropogenetic emissions of CO2."

Jan 1, 2010

By F. A. Myzenkov

The technology developed by the authors uses new methods for raw material smelting in electric furnaces, a new autogenous method and apparatus for subliming smelting for antimony trioxide production and separation of antimony and gold. Concentrate produced from the ore deposits in Yakutia has the following average contents of main constituents, % by weight: 29.4 Sb, 1.2 Fe, 13.1 S, 40.0 SiO2, 0.2 As, 2.6 CaO and 45 g/t of Au. Unlike the technology used abroad a new autogenous method makes it possible to increase considerably specific capacity and reduce gold losses with antimony trioxide by several times. At the same time mineralogical composition of trioxide has improved considerably ? it has mainly a cubic base with prevalence of senarmontite. The content of a main component (Sb2O3) in the final product has increased from 99.0% up to 99.6% which means better quality and makes it suitable for use in special technologies. Despite a lower antimony content of the concentrate (29.4% as compared with over 33% as common in the world practice), an antimony recovery of 85.3% into a commercial-grade product has been achieved, as well as a gold recovery of 96.65% into a gold-antimony alloy. The technology for processing gold-antimony materials developed and introduced at the Ryaztsvetmet plant is unique in the world with respect to gold recoveries.

Jan 1, 2006

By Ruixuan Zhang, Yan Li, Shusen Cheng

The measurement of raceway temperature in the blast furnace is a critical issue, which is very significant for judgment of, prediction and diagnosis of the racewa yburning state. This paper deals with mathematical models by Monte Carlo method to approximately simulate the radiation heat transfer in the race-way and establish matrix equations using CCD cameras, which are solved to obtain the three-dimensional temperature field. Due to the existence of fluctuation error, CCD camera measurement error and others,this is analyzed and random error is added in the measurement data to demonstrate the effectiveness and stability of the reconstructed temperature field. The results show that the reconstructed three-dimensional temperature field of the raceway is very close to the exact temperature.

Mar 1, 2017

By C. E. M. Meskers

End-of-life Electronic and Electrical Equipment, o_cially called WEEE, is unjustly regarded as mainly a waste management problem. What is structurally overlooked is the enormous resource impact of these devices. EEE rep- resents a tremendous metal resource, which should be uti- lized through e_ective recycling, which has a much lower environmental footprint than primary production. The actual amount of end-of-life EEE recycled today is embar- rassingly low since insu_cient EEE is collected and part of the collected EEE is exported to developing countries, where it is largely not entering o_cial recycling systems. To achieve a global recycling society issues like technol- ogy, economics, life cycle structure, stakeholder aware- ness and legislation have to be addressed in a global, co-operative manner so that sustainable closed product cycles can be obtained. Requirements for a "global re- cycling society" are de_ned to address today's reality of global ows of used consumer products, taking into ac- count the likely needs of the future.

Jan 1, 2009

By Lilong Zhu, Shaoda Zhang, Qian Wang, Shengping He

The effects of ZrO2, Y2O3 and Sc2O3, which are transition metal oxides, on the melting temperature, viscosity at 1300 °C, and break temperature of three mold fluxes (two weak-reactive type and one non-reactive type) designed for the high manganese and high aluminum steels, and one another conventional CaO-SiO2 based mold flux is studied. The results indicate that the melting temperature and viscosity increases slightly, and the break temperature increases dramatically with the addition of ZrO2, Y2O3 and Sc2O3 content in the conventional CaO-SiO2 based mold flux system. While, the addition of ZrO2, Y2O3 and Sc2O3 in the weak-reactive or non-reactive mold flux systems has a negligible in fluence on the melting temperature, viscosity and break temperature, suggesting that these transition metal oxides are possible to regulate radiation heat transfer without changing the basic properties of mold fluxes.

Mar 1, 2018

By Pesic. Batric

A novel chitosan-pyridoxal-epichlorohydrin was synthesized and evaluated in our laboratories. The evaluation was achieved by performing kinetic and equilibrium studies of copper sorption. The parameters examined were pH, temperature, concentration of copper, particle size and selectivity of copper sorption against iron, zinc, cadmium and cobalt. It was found that pH was the most important parameter, and sorption of copper increased with pH increase in the range pH 2.5-6.0. The low activation energy of the sorption reaction, 1 1.13 kJ/mole (2.66 Kcal/mole), showed that temperature was not an important parameter. The synthesized chitosan was selective against iron, zinc, cadmium and cobalt. The selectivity with respect to last three metals was achieved by the kinetic difference of sorption, as sorption of copper was much faster than for other metals. Iron (Fe2+) does not adsorb on chitosan. The mechanism governing the sorption of copper is intraparticle diffusion. This finding was supported by the dependance of copper sorption on the square root of time, the low activation energy, and the fit of experimental data in the diffusion through the product layer equation.

Jan 1, 1994

By V. B. Chernyavsky, Ladokhin S. V.

Equipment and continuous casting technology for the production of small diameter copper rods and tubes are described. Industrial copper wastes, such as scrap and shavings, were used as the charge. An electron-beam installation for rod and tube production includes a crucible with an electromagnetic stirring system and a pouring hole in its bottom, a bottomless mold, .and a special cooling system, which includes an oil and water cooling devices. For the first time in the electron-beam technology, rods of 8 mm and 14 mm diameter mm tubes of 14 mm external diameter and 7 mm internal diameter were produced through continuous casting by pulling them out of the vacuum chamder into the atmosphere with depressurizing the vacuum chamber. The production capacity of a single strand continuous casting machine was 200 mm/tnin for rod casting and 150 mm/min for tube casting.

Jan 1, 2000

By Jian Zhang

From the standpoint of quality, surface cracks normally pose more of a problem than internal cracks. Hypo-peritectic (HP) steel grades are well known for their proneness to surface longitudinal cracking (SLC) during continuous casting. This study analyzed the influences of chemical composition, technique parameter and secondary cooling on the surface longitudinal cracks. Based on the optimized the first and secondary cooling zone water distribution in the process of continuous casting, low cooling water distribution at solidification initial stages and uniform cooling at secondary cooling zone were suggested, which can be used to effectively control the surface longitudinal cracks.

Jan 1, 2010

By Bob Drew, Alfred Spanring, Kirschen. Marcus

"Increasing material conversion and energy efficiency, and decreasing carbon dioxide emission levels are crucial for sustainable production processes in the aluminum, cooper, and steel industries. RHI supports these targets by providing a diverse range of solutions including high quality refractory linings, optimum lining maintenance, and process improvements. In this paper examples are provided of process improvements and increased energy efficiency in copper refining, potential energy savings during electric arc furnace and ladle operations in the steel industry, and increased energy efficiency by improved heat transfer in anode baking furnaces in the aluminum industry. In all cases, RHI’s expertise in close collaboration with the customer resulted in an improved performance of the reactor lining and the actual high temperature process with a positive impact on the material conversion and energy efficiency and as a result a decrease in specific carbon dioxide emission levels.IntroductionRefractory linings play an important role in heat transfer during high temperature processes in for example the aluminum, copper, and steel production industries. Due to constantly increasing energy prices worldwide and the increasing demands for environmental and climate protection, improving the energy efficiency and decreasing emission levels of these energy intensive production processes is of significant importance. In this paper, the contribution of modern RHI lining technologies to energy saving measures and the corresponding reduction of specific carbon dioxide emission are described. The type of current refractory solutions for energy intense processes are illustrated with four examples: Optimization and increase of material conversion and energy efficiency in copper refining, energy saving potentials in both electric arc furnace and transport ladle operations in the steel industry, and heat transfer improvements during the carbon anode annealing process in the aluminum industry. These examples focus on particular production processes operating with a high proportion of recycled copper, steel, and carbon anodes. Increased energy efficiency directly decreases the specific energy related carbon emission levels whereas improvements to the metallurgical processes aim to increase material conversion efficiency and, therefore, decrease specific process related carbon emission levels. Significant energy savings can be achieved by maximizing the refractory campaign length through a combination of appropriate refractory material selection, grade zoning, correct installation, careful preheating, and effective maintenance strategies. Besides the efforts to improve the performance and energy efficiency of customer high temperature processes, RHI continuously promotes the development of new low emission carbon-containing refractory bricks and unshaped products."

Jan 1, 2008

By T. K. Mukcherjee

The importance of the processing of secondary resources such as solid industrial wastes and liquid effluents as well as byroducts for the recovery of the associated metal values hardly needs any elaboration. Such processing contributes in no small measure.towards the augmentation of the availability and the supply position of resources. As an added benefit, it leads to a reduction in environmental pollution caused by the undesirable waste materials. As some typical examples of secondary resources in the Indian scenario, mention' can be made of spent catalysts, metal/alloy scrap, ash, consumed batteries, flue dust, slag, sludge and slime, pickling solutions, spent acids; plating rinse solutions, spent etchants, waste water from synthetic fibre manufacture and from tanneries etc. These wastes constitute a source of a variety of non ferrous metals. In the processing of secondary resources like these, the techniques of hydrometallurgy such as solvent extraction play a pivotal role. This paper outlines the efforts made to use solvent extraction to recover(1) base metals. such as copper, zinc, nickel and cobalt from a number of secondary resources like cake, and sludge(2) refractory metals like molybdenum and vanadium from sulphidic byproducts and spent catalyst and (3:) nuclear metal like uranium from phosphoric acid. In the case of base metals, process flowsheet involving the use of acidic extractants such as DEHPA and PC88A have been optimised. The problem of iron removal from the leach liquor, "which influences the metal recovery process significantly, has drawn a special emphasis. hi the case of refractory metals, basic extractants .like Alamine 336 has been pressed into service to produce kilogramme. quantities of pure salts of molybdenum and vanadium, Finally, the paper gives a brief account of plant experience in recovering uranium from phosphoric acid, using 'a solvent system comosed of DEHPA and TOPO.

Jan 1, 1996

By Carlos Frias

The lead-acid battery recycling is a major industrial activity (more than four million tonnes recycled lead per year) that generates large amounts of toxic wastes such as lead slag, mattes and acidic sludge, besides airborne emissions. This is a waste-producer industry that needs a definitive solution to avoid its negative environmental impact and getting a sustainable lead production. That is the principal target of the CLEANLEAD technology, which properly combines both hydrometallurgical and pyrometallurgical routes aiming to get zero-waste production, reducing the use of energy and resources in all phases of battery reprocessing, and consequently, greatly decreasing the operating cost. There will be no toxic emissions to land, water or air, and obtained products are pure lead metal or pure lead oxide, and commercial gypsum instead of waste sludge.

Jan 1, 2006

By M. S. Borges

The need for the waste management industry to reach environmental patterns, technological innovation, and a technological demand of the productive sector is covered by this study. The environmental care and responsibility in the industrial sector and the necessary cultural changes for companies and entities is also emphasized. A collaborative tool was developed to help all partners involved in the environmental administration. This tool focuses on the interaction among residue generators in the productive chain. It was developed for a vehicle assembler company supported by entities or institutions with emphasis in the research, development and innovation, with expertise and capacity for new products creation, as well as reuse, recycling and reduction of by-products generation. The work aims to establish a tool for socio-environmental management, focusing on promotion and interaction between industrial waste generators sectors.

Jan 1, 2010

By V. Ramachandran

In view of the increasing environmental regulations that have been promulgated in the last 30 years, non-ferrous smelters and refineries have learnt to handle effectively the process waste streams that need to be bled from the system for impurities' control The cations of concern are copper, lead, zinc, cadmium, mercury, thallium, nickel, silver, sodium and potassium. Anionic species of arsenic and selenium also need to be addressed, Sulfates and chlorides-not a major concern at present-have come under scrutiny in the recent past. The current paper reviews several treatment options with reference to a) types of waste streams processed b )process chemistry c)discharge options and recovery of treated water and d) sludge disposal The long term goal of any smelter and/lor refinery should be to achieve zero liquid discharge from the plant. Methods to obtain zero discharge are discussed.

Jan 1, 2003

By L. Escudero-Castejon, S. Sanchez-Segado, A. Jha, Y. Hara, S. Parirenyatwa

In a world where declining ore grades are increasingly common, it has become necessary to process low-grade feedstock. Carbothermic reduction in the presence of alkali (Na2CO3) has been adapted to beneficiate waste that contains titaniferous minerals (TiO2 ca. 12 wt%), in order to recover valuable constituents such as TiO2, Fe and V2O5. The waste from vanadium metal processing has environmental legacy as it leaves nearly 1 wt% V2O5 process waste, which is environmentally problematic due to V5+ ions in contact with water and soil. This investigation focuses on the kinetics and mechanism for alkali reduction of mineral waste bearing 10–12 wt% TiO2, which we studied in the 1073–1323 K range. The thermogravimetric analysis (TGA) technique was used to record weight loss data. Two distinct regimes demonstrated mixed-control kinetics: (1) at low temperatures the activation energy was found to be 199 kJ mol−1, which corresponds to the outward diffusion of O2− ions; and (2) at high temperatures the calculated value was 130 kJ mol−1, which is consistent with the activation energy for the outward diffusion of Fe2+ ions. The metallic iron, sodium titanate and sodium aluminosilicate phases that formed were characterised using X-ray powder diffraction (XPRD) and scanning electron microscopy (SEM) techniques, and their significance for metal recovery is explained.

Mar 1, 2017

By Jewel A. Gomes

Keywords: Electrocoagulation, arsenic removal, fuel cell, windmill, energy simulation, combined Fe-Al electrode assembly Arsenic contamination of well-water in different countries has caused signs and symptoms of arsenic poisoning. Although several physicochemical treatments are presently used for the removal of arsenic compounds from drinking water, an electrochemical treatment, electrocoagulation, is a promising processing technology and currently is the most efficient (above 99% removal) and environmentally friendly technique, particularly if combined with alternative energy sources. Wind and fuel cell technologies can be considered the most promising developmental clean power sources. We will discuss new insights into the materials processing mechanisms and show the coupling of electrocoagulation with fuel cells and simulated wind energy sources. Different electrocoagulation plate materials were considered, along varied currents from the fuel cell to produce maximum arsenic removal. Coupling these technologies will remove carcinogenic arsenic from water sources, and will exhibit efficient usage of these energy sources by producing pure water for human and agricultural consumption.

Jan 1, 2005

By Ernt. W. D.

A membrane based mixed extractant process was developed for selective removal of copper from waste acidic cupric chloride etchant solutions found in printed wire board manufacturing. The process uses a mixture of Adogen 381 (tri-isooctylamine), MOC®-45 (ketoxime) and MOC® 55TD (aldoxime) in a kerosene diluent. The mixed extractants recover the copper from a hydrochloric acid medium and transfers it to a sulfuric acid medium. The process also utilizes unique wetted membranes to separate the aqueous and organic phases. The driving force for these membranes is not pressure but the difference in surface tension between the two phases. By using these membranes, complete phase separation results. There is no physical entrainment contamination as found in conventional systems. The only cross contamination is the solubility concentration of one phase in the other. This however is less than 10 mg/l.

Jan 1, 1998

By E. Saez, M. Bellet, T. Coupez, O. Jaouen

"The paper presents a 3D finite element solver for non-steady state fluid flow. The thermomechanical simulation package REM3D® has been initially developed to model Stokes' flow for polymer injection. The mechanical module is based on a Eulerian velocitypressure formulation. The spatial discretization uses P 1+IP1 tetrahedral elements. The front tracking module consists of the resolution of a transport equation, thanks to a space-time discontinuous Galerkin formulation. It includes mesh adaptation, which permits a dynamic refinement at the front, thus controling the numerical diffusion. The same approach is used to solve heat transfer. In this paper, we focus on the specific adaptations done to treat Navier Stokes flow. The treatment of inertia is detailed, as well as the implementation of sliding conditions at mould surface, using conservative normals. Industrial applications are presented.IntroductionThe study of the mould filling stage in casting processes requires the ability to simulate complex non steady-state three-dimensional flows. Most commercial software use the volume of fluid (VOF) method, associated with a Eulerian formulation, see for instance the series of conferences ""Modelling of Casting, Welding and Advanced Solidification Processes"" [1-3]. The VOF method [4] consists in solving the conservation equation dF / dt = 0 for a variable F - the volumic fraction of fluid - whose value is 1 in filled regions and 0 elsewhere. Two fluids are actually considered: the molten alloy and a gas in the empty regions. This method suffers generally from numerical diffusion in the resolution of the free surface tracking equation, which is of pure advective type. The precision of the computation is then strongly dependent on the mesh density. Since the mesh is fixed (Eulerian formulation) this implies that in case of complex flow the user must have a priori a fairly good idea of the flow characteristics in order to capture properly the critical features of the flow. In addition, the method can hardly handle the discontinuity of the material viscosity at the interface. To prevent this difficulty, the viscosity value is smoothed around the interfuce, adding once again some inaccuracy. Since the value F = ½ is supposed to represent the free surface, it results in a smeared fluid surface. An alternative to the fixed mesh methods are the methods in which the mesh covers the fluid domain only, as proposed by Navti and Lewis [5-6], or Gaston and Bellet [7]. Based on updated Lagrangian schemes, they must be associated with an ALE formulation (arbitrary LagrangianEulerian) in order to reduce the number of full remeshing operations."

Jan 1, 2004

By Emma Arakelova

An increase in concentration of a Zn-containing volatile complex for synthesis of ZnO films was investigated when processing their target by ultraviolet radiation emitted by mercury lamp. The experiments were carried out using a flow-type quartz reactor. ZnO tableted target was preliminarily irradiated during 2 to 7 hours. H2O2 (98%) vapor at 25Pa passed through the reactor with ZnO target at 373K. As substrate material, five subsequent quartz cylinders were used at 423K. The experiment lasts 4 hours. H2O2 decomposition on ZnO surface was accompanied by formation of a Zn-containing volatile complex which passed in gas phase and decomposed on the substrates with isolation of final ZnO. The concentration of the Zn-containing volatile complex (N) in gas phase increases with UV pre-irradiation time (t) (without irradiation N = 1.05 1011 particles/cm3; after t=2 hours, N = 5.19 1011 particles/cm3, after t=4 hours, N = 9.95 1011 particles/cm3; after t=7 hours, N = 1.86 1012 particles/cm3.

Jan 1, 2006