Search Documents

By J. Phillip Mackey

A whole new group of non-ferrous pyrometallurgical processes with the ability to utilize tonnage oxygen and capture sulphur dioxide were developed and commercialized over the period 1940s–1980s. Many of these earlier process developments were undertaken with limited knowledge of the process chemistry and influence of key process variables; in many cases, piloting helped provide much new physico-chemical data, but gaps remained. The second generation versions of these technologies of today provide all the primary copper, nickel and lead produced worldwide by pyro-metallurgical smelting. Further, process development has continued and a new generation of copper and lead smelting technologies have also been developed in China since the 1990s. The older reverberatory and blast furnaces have been progressively replaced by the newer technologies—a good example being the introduction in 1992 of the copper IsaSmelt technology at the Mt. Isa smelter in Australia where the former fluid bed roaster and reverberatory furnaces were replaced by a single new smelting unit, together with an acid plant for sulphur dioxide collection. The development of these new technologies was made possible by investment in fundamental and applied research. The lesson for the future is, in order to sustain these improvements, continued investment in research and development capability is required—to do otherwise is to risk obsolescence and lack of competiveness in the world market. Dr. Peter Hayes at The University of Queensland is one of the many researchers and process engineers who have contributed to the fundamental understanding of metallurgical processes over this period of rapid change in technologies. The present paper briefly outlines some of the many contributions Peter Hayes has made to the understanding of kinetics, mechanisms and phase equilibria in metallurgical systems, and metallurgical process development.

By M. O. Lai

"Metal matrix composite (MMC) with composition of Al-4.Swt.%Cu reinforced by IOwt.%TiB2 or ISwt.%SiC particulate has been successfully fabricated using powder metallurgy technique. Disk, compression and beam specimens were prepared with (a) layered structure containing ductile Al-4.Swt.%Cu with brittle Al-4.Swt.%Cu/TiB2 or Al-4.Swt.%Cu/SiC layers, and (b) homogenous constituent with composition of Al-4.Swt.%Cu/lOwt.%TiB2' The specimens for the fracture toughness measurement were built through three ductile-brittle-ductile alternating layers. For the beam specimens, the layers were built through brittle-ductile-brittle sequence. The brittle layer consisted of Al-4.S%Cu with fixed amount of reinforcement. Fracture toughness testing revealed an increase for layered composites although the total amount of the reinforcement was the same for all disk specimens. The increase in fracture toughness is due to the existence of ductile layers which manifests a strong influence on delaying the occurrence of fracture. It acts as a barrier to resist the propagation of crack and hence increases the fracture toughness of the layered MMC specimens, Delamination in the beam specimens was observed to be due to shear stresses. Fracture surfaces of both disk, compress and beam specimens were characterized using the SEM. IntroductionMechanical and thermal properties can be achieved by the incorporation of refractory secondary phases to constrain the plastic flow of the matrix in a metal matrix composite (MMC). The size of the reinforcement particulate incorporated must be in the range larger than the dislocation cell size and strongly bonded to the matrix (I). Particulate reinforced metal matrix composites hence provide high modulus, improved wear resistance and strength (2-4). Because of the incorporation of refractory phases which are generally brittle, the major limitation in the mechanical properties of MMCs is their limited ductility in comparison to their base metals. Cracks normally initiate from the reinforcement and voids (4, 5). Due to the lack of ductility, cracks propagate rapidly with increase in load. As a result, the interactions between reinforcement particles and propagating cracks have recently been of great research interest (6). In addition, volume fraction of reinforcement and aging condition of the matrix significantly affect the mechanical behaviour of MMCs. In the case of AI-3.5%Cu reinforced with varying volume fractions of SiC particulate, it has been found that the probability of particle fracture increased with increasing volume fraction of reinforcement (7)."

Jan 1, 1996

By Jiangwei Shen, Cong Wang, Haibin Zuo

The research on the formation of Silico-Ferrite of Calcium and Aluminium (SFCA) in the process of cooling and solidification is rarely reported. The crystallization process was observed by using scanning electron microscopy (SEM) and optical microscope in this paper. The effect of different cooling system on the microstructure and phase composition of the sinters was investigated to obtain the appropriate cooling rate to improve the metallurgical properties of sinters. The experimental results show that the crystallization of calcium ferrite is getting better when the cooling rate is decreased from water quenching to cooling in the air. There are a large number of hematite phases with interconnected crystal structure in the sample cooled in the air. In the case of the compressive strength, it was determined by the mineral composition and pore structure, higher SFCA and hematite contents in sinter cooling in the air lead to a higher strength. Glass phase in the water quenching sinter was the major reason for the lowest strength. High porosity contributes to a decrease in compressive strength for the sinter cooling in the furnace. Therefore the air cooling was the appropriate cooling rate to achieve high quality sinter under this experimental condition.

Jan 1, 2016

By James Vaughan

Australia is a major miner of ore that requires hydrometallurgical processing. According to the 2016 US Geological Survey Minerals Commodities Summaries, the country is 1st for aluminium (bauxite) and lithium, 2nd for gold, zinc and cobalt, 4th for nickel and silver, and 6th for copper mining, not to mention its wealth in coal and iron ore. In this paper, examples of recent Australian hydrometallurgical activities are summarised. Then, selected research projects from the University of Queensland hydrometallurgy research group are profiled. The projects profiled are related to fundamental aspects of processing bauxite with organics and reactive silica as well as the development of a synergistic hydro- and pyrometallurgical process for copper. The process context and motivation for the research is introduced, key results are highlighted with the associated relevant references.

By S. A. Platias

Large amounts of dunile tailings can be recycled for olivine produdion from the existing beneficiation adivity of chromite ore in northern Greece. This olivine production aims at the preparation of a material suitable for the substitution of the environmental hazardous quartz sand in the foundries of Europe In smelting of chromite ore the losses that occur ore usually of the order of 6-8% Cr that report in the slag. Most of this is in the form of oxides that cannot be recovered, but usually 30-35% is in the form of FeCr alloy that can be recovered by gravity methods. About 90% of the produced slag is sold for road construdion after crushing to a desired grain size. Finally, recycling of chromites sludges from the ferrochrome produdion plant, through the preparation of pellets, improved the total chromite yield by 2%.

Jan 1, 1996

By Giacobbe Braccio, Alessandro Blasi, Assunta Romanelli, Massimo Morgana, Corradino Sposato

Yttrium is a strategical material for its several usages in a wide range of industrial production. For this reason, improving the recovery of Yttrium has become a crucial focus for international research. In this scientific activity, the utilization of two extractants, 2-ethylhexyl-mono 2-ethylhexyl ester phosphonic acid (P-507) and sec-octylphenoxy acetic acid (CA-12), working in a synergistic extracting system, has been tested. A series of trials have been carried out to optimize the experimental conditions in order to separate yttrium from a mix of heavy rare earths in chloride media. Tests with different relative concentrations of extractants and a phase modifier (TPB, trybutyl phosphate), with different presaponification rate, have been performed to evaluate the behavior of the synergistic system. Results are very promising to recover and separate yttrium with a high purity.

Mar 1, 2017

By Matthew John M. Krane, Patrick E. Krane

This study examines the operations of the Cowper stoves attached to an iron blast furnace from a Second Law perspective. The exergetic efficiency of a 3-stove system operating at cyclic steady state is determined using a model accounting for the thermal, mechanical, and chemical flow exergies of the top gas and blast air, as well as the thermal exergy stored and released in the stoves. The analysis covers the heating and mixing of blast gas in one on-blast stove, and the combustion of top gas and its use to heat two on-gas stoves. The effect of different cycle times, and blast furnace operating conditions on the exergetic efficiency of the cycle is examined, and the optimal cycle time for different blast temperatures found. In addition, a study of the combustion parameters quantifies the advantages of using enriched oxygen in the combustors.

Mar 1, 2018

By C. Landolt

Inco's Copper Cliff Smelter Complex produces some 11 5,000 tonnes per year of nickel and 120,000 tonnes per year of copper. The Smelter flowsheet has changed a number of times over the years. The most recent changes were effected in the mid-1980's in response to new realities in metal markets and heightened awareness about the workplace environment. By 1994, the flowsheet will undergo yet another metamorphosis as part of Inco's SO2 Abatement Program. The paper discusses the improvements implemented during the 1980's and projects the processing in the Smelter through 1994.

Jan 1, 1993

By Mario Sanchez, Jose Palacios, Fernando Parada

Carbon steels have less than 0.02% copper and have low atmospheric corrosion resistance. The addition of at least 0.20 wt% Cu improves this property. Also, 0.8 wt% Cu in steel shows a hardening potential for developing high strength corrosion resistant steels. Copper slags containing 42–45% of iron, silica and minor amounts of copper were used for producing Fe–Cu alloys by reducing the oxides contained in the slag to obtain a Fe-0.84 wt% Cu alloy, which could be suitable as feeding material to manufacture a corrosion resistance steel, and also would be an alternative for minimizing the copper industry ’s environmental impact, and to introduce the application of the Circular Economy concept to the natural resources exploitation, especially in countries where their economy is strongly based in mining and metallurgical extraction.

Mar 1, 2018

By D. Gregurek

In non-ferrous metal furnaces the installed magnesia-chromite refractory lining is exposed to several stresses, rather complex in their interaction. Therefore, a detailed investigation and understanding of wear mechanisms through “post mortem studies” is an important prerequisite for refractory producer. Additionally, in order to determine the most suitable refractory products and to improve the lining life of refractories, practical corrosion testing with processing slags is performed. For this purpose the test-facilities, such as induction furnace, rotary kiln but also cup test and drip slag test, allow the best possible understanding of chemothermal brick wear on pilot scale. Prior to testing a complete mineralogical investigation, thermo-chemical calculation via FactSageTM of the slag was carried out. Based on such research results, combined with specific process knowledge RHI Magnesita can recommend appropriate brick lining solutions for non-ferrous metal furnaces.

By Edgar Peek

Lixiviant regeneration is by definition a precondition for any hydrometallurgical process. In chloride hydrometallurgy either HCl or Cl2 has to be regenerated in order to establish an economically viable metallurgical process. One such regeneration process is widely used with steel pickling where HC1 is regenerated through the thermal decomposition of ferrous chloride in either spray roasters or fluid bed pyrohydrolyzers. This standard HC1 regeneration process deserves to be considered as a potential separation process, since thermodynamic calculations show that a fluid bed pyrohydrolyzer can function as a ferrous-nonferrous separator. Several nonferrous,metals such as zinc, lead and cadmium can be volatilized as a chloride under ferrous chloride pyrohydrolysis conditions. If such a nonferrous metal volatilization could be achieved in the case of slurry feeding of "contaminated" iron oxides, then this would increase the Fe/H2O ratio of the (process) feed and thus save on fuel per ton of iron, while yielding a marketable iron oxide product. Previous test work on synthetic materials revealed that the near-complete separation of zinc, lead and cadmium from iron oxide was possible in a pyrohydrolytic atmosphere, even if zinc was present as zinc ferrite (more than 99.5%). This investigation, which was carried out in a tube furnace at 1100 K has now been extended to treat synthetic zinc minerals and also franklinite ore. For the latter, it was found that 85% zinc volatilization could be achieved in 4 hours at 1300 K. It is postulated that complete zinc volatilization could not be attained due to the formation and/or presence of gahnite and hardystonite, which might be stable in HCl/H2O atmospheres at 1100 K. The effect of adding small amounts of calcium chloride to react with gahnite and hardystonite to give zinc chloride and both calcium aluminates and silicates is being discussed. Test work on slurry feeding of this complex ore in a recently constructed 4-inch diameter fluid bed pilot unit has been planned for the near future.

Jan 1, 1995

By W. Riekehof

The paper explains required practice and equipment for capturing airborne fumes and particulates in hot-dip zinc galvanizing plants. An economic and technical comparison of enclosure and tank rim suction options is presented. The paper also compares the performance of various filter media in filtering fumes, to determine the effect of changes in flux as well as changes in filter finishlcoating methods. This includes a recommendation for how to achieve the best result with respect to pressure loss and cleaning behavior of the filter.

Jan 1, 1992

By Matthew C. Binsfield

The simultaneous electro winning of zinc and manganese from waste water treatment plant sludge was studied as a part of the overall research program, which was conducted to develop the methods for removal of environmentally hazardous metals from the Bunker Hill Superfund Site. This paper discusses the electrolytic method for recovery of zinc and manganese from the solution produced by leaching of sludge with S02 + H2S04. After three stage purification of the leaching solution, zinc and manganese were electro won simultaneously in an undivided electrolytic cell. Zinc was deposited on an aluminum cathode, while manganese was simultaneously produced (as Mn02) on a lead silver anode. The electrowinning parameters studied were the effects of: temperature, current density, electrode material, spacing of electrodes, composition of electrolyte, and electrolyte additives. Anodic and cathodic efficiencies were 30 and 91%, respectively. In light of the process design parameters discussed in the paper, which are affecting the electrowinning, these efficiencies were found as acceptable with regard to the quality and marketability of the products.

Jan 1, 1996

By Rolando Campos

Until 1970, the Caletones Smelter of CODELCO-CHILE, División El Teniente, operated under the conventional pyrometallurgical process used by most of copper smelters. The annual copper production varied around 165.000 tons. The failure in the commissioning of the "oxygen smelting" technology in Peirce- Smith converters (1970-1972), forced further introduction of transcendental changes in the Caletones smelter operating scheme. Implemented technological innovations were based on wide studies and research works performed by División El Teniente. This paper presents a summary of technological modifications introduced, their impact on production and energetic performances, and short and medium terms improvement plans.

Jan 1, 1993

By Theo Lehner

The Rönnskär smelter has wide experience in the field of recycling of non-ferrous metals. Today, smelting and refining from primary and secondary raw materials are integrated in a complex flow sheet. Boliden operates a lead flash smelter, a lead refinery, a copper smelter and refinery, a sulphuric acid and sulphur dioxide plant, a slag fuming plant and precious metal plant at its Rönnskär smelter in the North of Sweden. The Business Area Smelter Operations also incorporates Boliden Bergsöe, Sweden's lead-acid battery recycler, and Norzink, Norway, where recycled zinc accounts for more than 20% of it's production. Raw materials for the Rönnskär smelter include concentrates, ashes, slags, metallic scrap, electronic scrap and electric arc furnace (EAF) steel-making dust. This paper briefly describes current operations and illustrates current measures to improve productivity. Limits to recycling as experienced by a non-ferrous smelter are, illustrated. The deportment of critical elements contained in raw materials is also discussed.

Jan 1, 1998

By Hsing Kuang Lin

Ferric chloride leaching w.as applied to a complex sulfide ore from Tok, Alaska to dissolve zinc, lead, silver and copper. Gold in the leaching residue, as well as in the ore, is found to be refractory to the conventional cyanidation process. Roasting, pressure oxidation and elemental sulfur removal followed by cyanidation were tested to improve gold dissolution. Also tested were thiourea leaching and high-pressure cyanidation. The readsorption of dissolved gold by carbonaceous matter in the chloride leaching residue was analyzed. Based on the experimental results, factors causing difficulty of gold dissolution from the leaching residue are discussed.

Jan 1, 1989

By Reza Ghomashchi

Casting is the most economical route to transfer raw materials into readily usable components. The economics of casting would be more pronounced and better realized, if there are no or limited necessary post fabrication treatments. Therefore, there is an urge towards near or net-shaped casting as there are significant advantages over conventional casting including reduction of component weight, excellent surface finish, higher strength and integrity of the as-cast parts, closer tolerance, and the ability to produce pore-free parts by controlling the solidification shrinkage. The concept of near or net-shaped casting is currently employed for both semi-finished products such as strip-casting and finished shaped casting, as in case of high pressure die casting or squeeze casting. The full potential of this process yet to be explored and is expected to be realized within the next 10 years, especially in case of strip casting. The current article discusses different near or net-shaped casting routes currently employed for fabrication of high integrity finished products with main emphasis on aluminum-silicon alloys. In this regard, attempts will be made to identify the key parameters during fabrication and highlight the importance of process control and optimization in fabricating premium quality cast products. Keywords: Near Net Shape casting, Solidification, die casting, squeeze casting, rheocasting, thixocasting

Jan 1, 2003

By Chengyi Ding, Xuewei Lv, Changyang Ji, Rende Zhang, Xiangwei Zheng

Inexpensive and high-quality sinter has an extraordinary position in iron making, and there are many factors influencing the sintering. This research takes the basicity and coal dosage as research subjects to do the experiments based on cost analysis with sinter pot experiment system. Linear program is taken to make the schemes of ore blending. During the experiments of changing basicity from 1.6 to 2.3, the properties and microstructures of the sinter are studied. It comes to a conclusion that increasing the basicity is beneficial to sinter quality but leads to higher cost. To further ascertain the cost of sinter and the potential of saving coke, the work of improving coal dosage is taken on the basis of experiments of changing basicity. Through analyzing the results, a formula (Y=1849+261.1R-130.6C) is proposed which indicates the relation among the cost, basicity and fixed carbon content. And it works well for actual production.

Jan 1, 2015

By C. Damiani

The Chuquicamata smelter, operating since 1952, has gone through several developing stages which have been characterized by the addition of peak technology for copper concentrate smelting (Teniente converter and Outokumpu flash furnace) with an intensive use of technical oxygen, which has permit-ted to partially discontinue the reverberatory furnace utilization. This paper shows the main indicators and operational practices at present, as well as those concerning maintenance aspects. Finally, the most relevant topics related to the future development of the smelter are mentioned with special remarks on the Decontamination Plan, which allows US to keep the high level of production, reducing the emission of contaminants according to the legal requirements in force.

Jan 1, 1993

By Biao Zhou, Qian Li, Kuo-Chih Chou, Yi-Long Liang, Jie-Yu Zhang, Qun Luo

"In this work, the phase transformational behaviors and microstructural characteristics of 60Si2CrVAT spring steel were systematically investigated as a function of applied cooling rates in the range of 0.l-10°C/s. A quenching deformation dilatometer was used to austenize and quench. The dilatometric curves between length changes and temperature of samples suggest three characteristic stages could be identified as different ranges of cooling rates, which meets well with metallographic examination and the measured hardness results. As the cooling rate increases, the structure transformed from pearlite, granular bainite to finally martensite. The F + P and B zones are completely overlapping in continuous cooling transformation (CCI) curve, which indicates that this steel is difficult to become single bainite and shows good hardenability.IntroductionThe 60Si2CrVAT, a high-carbon low ally super-high strength steel developed from the ?OCT 60C2XFA and 60Si2MnA, is often used for coil spring of heavy vehicles and high-speed railway by hot deformation or cold deformation [1-3]. The addition of Si improves relaxation resistance significantly, through the refinement of tempered carbides as the result of the retardation of E -carbide conversion to cementite during tempering. Due to its deleterious effects on decarburization and toughness, the maxinJum content of Si has limited to 1.5 or 2.0% [4-5]. Additionally, V and Cr can improve sag resistance due to the precipitation of fine carbonitrides during hot rolling [6-7]. To best of our knowledge, the strengthening by precipitation of alloy carbides of Cr and V often referred to secondary hardening [8]."

Jan 1, 2013