Search Documents

By R. R. Odle

A laboratory and pilot-scale investigation of direct smelting of copper concentrates was conducted to determine the effect of concentrate analysis and the degree of roasting on the yield and quality of copper produced in a subsequent smelting step. A stoichiometric :mOdel of direct smelting is presented which predicts the? quantity of copper; slag, and white metal' prOduced'and the distribution of copper in these phases as a function? of the concentrate '(calcine) analysis.

Jan 1, 1983

By P. M. Swash

The paper describes the use of mineralogical methods in the exploration and evaluation of primary diamond occurrences. The most common methods that are used include the systematic search for kimberlitic indicator minerals, surface textural study of the indicator minerals, (garnet, spinel, ilmenite and chrome diopside) and alluvial macrodiamond studies so as to understand their provenance and guide exploration towards diamondiferous targets. The mineral chemistry of the indicator is used to positively assess the origin of the mineral grains and is also pivotal in the determination of the diamond potential of a deposit. Petrography of the primary deposit is able to identify the body to be kimberlitic and is also a support to the mineral chemistry findings. Unambiguous proof of a prospects potential to contain macrodiamond is proven by the occurrence of microdiamonds in the residues from the rock. The presence of a sufficient number of microdiamonds in the rock is enough to determine a semiquantitative grade estimate and warrant further metallurgical evaluation so as to determine its actual macrodiamond content.

Jan 1, 1991

The standard procedure of fire refining consists of sulphur removal via air injected through tuyeres, arsenic slagging via soda-lime flux and oxygen reduction by air or oxygen deficient air or a steam fuel mixtures. The use of porous plugs to stir with an inert gas has been mainly considered as a surface renewing agent that increases the product quality and shorten the refining cycle. In the present study the effect of the bottom stirring by nitrogen gas injection through porous plugs for the treatment of the crude copper in the range of 400-150 ppm sulphur, 3,000-2,000 ppm arsenic and 14,000-7,000 ppm oxygen content was investigated. The combined effect stirring-reducing, by the use of air or a steam fuel mixtures through tuyeres for oxygen removal, follows a kinetics of first order where the constant, K, can be represented by the following polynomial expression: K = A * R2 + B * R + C Where A, Band C are constants that depend on the nitrogen flow rate and R is the air-fuel ratio or the steam-fuel used in the reducing step. Depending on the optimization of the flow of nitrogen and the air-fuel or steam-fuel mixture and only if just the oxidation, complexing and reducing steps are considered, the process cycle might be shortened by 45%.

Jan 1, 2003

By M. S. Borges

The need for the waste management industry to reach environmental patterns, technological innovation, and a technological demand of the productive sector is covered by this study. The environmental care and responsibility in the industrial sector and the necessary cultural changes for companies and entities is also emphasized. A collaborative tool was developed to help all partners involved in the environmental administration. This tool focuses on the interaction among residue generators in the productive chain. It was developed for a vehicle assembler company supported by entities or institutions with emphasis in the research, development and innovation, with expertise and capacity for new products creation, as well as reuse, recycling and reduction of by-products generation. The work aims to establish a tool for socio-environmental management, focusing on promotion and interaction between industrial waste generators sectors.

Jan 1, 2010

By Chuanfu Zhang, Liwei Liang, Yanxin Wu, Jinliang Wang

"According to the reaction shaft operation characteristics during the flash smelting process, 15 groups of slag samples containing high Fe3O4 were prepared by some chemical reagents, and then the slag viscosities were measured using a RTW-10 type synthetic test instrument for melt physical property by the rotating cylinder method. The effects of Fe/SiO2 ratio (mFe/mSiO2), Fe3O4 content (wFe3O4), Cu2o), MgO content (WMgO) and Cao content (wCaO) on the slag viscosity were also studied. Results show that slag viscosity is decreased with the increase of temperature, mFe/mSiO2, wCu2o, wMgO and wCao, and with the decrease of wFe3O4, under the range of slag contents: mFe/mSiO2 1.36~1.78, wFe3O4 17.83%~21.18%, wCu2o 3.51%~8.34%m wNgI 2.21%~6.57%m w/caI 6.22%~9.387% and temperature range if 1250 o/c~1450 oC. Only wFe3O4m and w/caO have great influence on the slag viscosity when temperatures as high as 1400 oC. Only wFe3O4 and wCaO have great influence on the slag viscosity when temperatures as high as 1400 oC or so. To form a freeze slag with higher viscosity inside the reaction shaft, wFe3O4 should be more than 20% and wCaO should be less then 6%.IntroductionSince its appearance in 1949, Outokumpu flash smelting technology has making continuous innovation and has become the most competitive intensified smelting technology [1], widely considered to be the standard clean smelting process [2]. At present, flash smelting technology is adopted to newly build or reconstruct most of the world's copper or nickel smelting enterprise [3]. Reaction shaft is the most important part of the flash smelting furnace. During the flash smelting process, reaction shaft must be able to withstand the following harsh conditions at the same time: 1) high temperature varying from 1400 °C to 1500 °C. 2) strong oxidative atmosphere containing 50% - 80% oxygen. 3) solid particles and melt with speed up to l00 m/s. 4) high acidic or basic slag with strong chemical corrosiveness. 5) smelting gas containing 50% - 80% SO2. 6) matte with strong dissolution."

Jan 1, 2012

By R. F. Hammen

Copper is one of the most widely used metals in industrial processes and is also present in most mining operations. Extraction of copper from solutions often proves difficult due to the presence of complexing agents. ChromatoChem, Inc. has developed a Solid Phase Extraction (SPE) support (HiPAC) for removal and recovery of metals from wastewater. The HiPAC SPE support employs chelating agents covalently coupled to a long linker molecule. Several solutions containing copper and complexing agents were tested including 1) copper and carbonate, pH 9.8, 2) mixed metals and anions with copper and cyanide, pH 11, and 3) copper and the chelating agent EDTA, pH 11. The copper was extracted from solutions one and two at high pH, but the EDTA containing solution needed the pH lowered to make the copper available for capture. In each example, the copper concentration was significantly reduced by HiPAC SPE treatment.

Jan 1, 1994

By M. M. Coleman

An investigation of the behaviour of sphalerite, chalcopyrite, galena and pyrite during flotation was conducted on selected circuits in the Brunswick Mining and Smelting Corporation Ltd. concentrator in Bathurst, NB. Samples were collected from 59 locations and analyzed for Zn, Pb, Cu, Ag, Fe, As, Sb, Sn, Bi and S. Metal balances were computed using the CAMP Material Balance Program (MATBAL 5) and the metal recoveries for each cell and circuit were calculated. An automated image analyzer interfaced with an electron microprobe was programmed to measure the size of sphalerite, chalcopyrite, galena and pyrite grains in each sample. The percentage of each mineral occurring as free grains and the relative amount of each mineral present in binary and ternary particles was calculated. The recoveries and losses of Pb, Zn and Cu are compared with the amount of liberated and unliberated galena, sphalerite and chalcopyrite present in the concentrates and tailings.

Jan 1, 1989

By Charles H. Rawlins

Reported is work done on processing of steel mill effluents in the areas of dewatering and separation. Much of the waste from these operations is in the form of sludges from scrubbers, in which the primary constituent is iron oxide. Recycling of the sludge&apos;s magnetic fraction has become economically attractive in order to reduce the overall volume placed in landfills. The objective of this research is to determine the effectiveness of combining magnetic and cyclonic forces, to recover iron oxide particles from waste water stream, while decreasing the volume to be disposed. Three different size hydrocyclones, operating within the field of a quadripole magnet, were tested using varying feed pulp densities of magnetite, magnetite/dolomite, blast furnace (BF), and basic oxygen furnace (BOF) slurries. In the first three cases, the percentage of magnetics recovered increased to greater than 95%. The limiting operational factors are; high pulp density for small cyclones, which can cause flow blockage within the magnet field, and extremely fine particle sizes (<2 microns), which cannot be recovered. The results indicate this technique can remove virtually all the magnetic particles from some steel effluents to a 40-50% weight percent solids pulp, on an in line continuous basis.

Jan 1, 1994

By Herman Wotruba

Mercury emissions and other environmental impacts in small-scale gold mining are a world-wide problem. "Clean" or better: "Cleaner" technologies have -apart from being environmentally sound -to guarantee a higher income and better working conditions for the miners in order to have a chance for long-term acceptance. In small scale primary gold mining in several South American countries, a number of techniques have been adapted and improved so that they not only were accepted due to their efficiency and easy handling, but they could also significantly lower mercury emissions.

Jan 1, 2003

By Cheryl S. Lim

New technologies such as direct reduction and smelting reduction processes are increasingly being used in iron-making and steel-making in addition to conventional blast furnace technology. Critical parameters for control of these processes include the degree of metallization, degree of pre-reduction, and carbon and silica levels. On-line monitoring of these parameters is difficult because measurements often need to be made on hot ores (at or higher than -1000&apos;C) in circumstances where representative sample streams are not readily accessible. A nuclear analyser has been developed which provides continuous, non¬intrusive, real-time measurements of iron, oxygen, carbon and silicon levels in hot ores undergoing reduction. The analyser has been tested in a plant using a direct smelting process on pre-reduced feed to the smelting vessel-, accuracies of 1% relative, 0.5 w&apos;.96 (25% relative) and 1.0 wt.% (9% relative) were obtained for the degree of pre-reduction, carbon and silica respectively. The underlying method, capabilities and potential applications of the analyser will be discussed.

Jan 1, 2001

By U. Lauwers

The influence of different waste materials in sinter blends on the quality and mineralogical composition of a sinter is described. As a result of partial preservation of the original textures of waste materials in the final product the degree of assimilation of the original material in the sinter product can be ascertained. Recycling of waste materials such as dolo char , arc-furnace slag, scrap fmes, mill scale and BOF-mud via the sintering process a saving on costs of raw materials such as flux and fuels, and a reduction on pollution can be achieved. A comparison of a typical sinter with a sinter produced through the utilization of waste materials showed a distinct correlation between certain types of waste material and some metallurgical properties. Dolochar in a sinter blend acts as part of the fuel and flux that are normally added to a sinter mix. Generally dolochar improves the quality of the sinter and decreases the consumption of coke. Other waste materials adversely influence the quality of the sinter. The glass and calcium ferrite content of a sinter when dolochar is used in the blend is similar to that of a sinter produced with only coke as a fuel in the sinter mix. The glass content is lower and the calcium ferrite content is higher, in a sinter produced from dolo char in the blend compared to a sinter produced with additions of other waste materials. Changes in the mineralogical composition are related directly to the metallurgical properties of the sinter product.

Jan 1, 1991

By Jr. Loper, M. H. Kim, H. H. Jo, C. S. Kang, T. S. Song

"An investigation has been conducted to describe the effect of grain refiner (e.g.,Ti) or modifier (e.g., Sr) on the microstructure of an Al-11.3wt%Si alloy produced by the Ohno horizontal continuous casting process using a heated mold so as to obtain directional solidification at high cooling rate of 300 to 2000°C/s. Experimental results demonstrated that the directionality of the primary a grain was promoted by the addition of0.2 to 0.4%Ti or by the addition of0.02%Sr, whereas the addition of0.6%Ti suppressed this directionality. Feathery a grains were promoted by the addition of 0.2%Ti, while these feathery a grains were suppressed when over 0.4%Ti (grain refinement) or when 0.02%Sr was added. The addition of Ti also resulted in increased coarsening of the eutectic Si in these Al-1 l.3wt%Si alloys.IntroductionThe mechanical properties of conventionally cast Al-Si alloys can be enhanced through judicious control of the casting parameters, by the addition of grain refiners (e.g., Ti) and by the addition of eutectic modifiers (e.g., Sr).[1-3] The Ohno continuous casting process[4-5] uses a heated mold (maintained at a temperature above the alloy liquidus temperature) to produce a casting with a mirror surface free of shrinkage defects. The process is especially suitable for the production of high quality and non-deformable rods of small diameter. This study was conducted at investigate the effects of Ti and Sr on the microstructure of Al-1 l .3wt%Si rods cast by the 01).no process."

Jan 1, 1998

By V. Kamavaram

Keywords: Recycling, Aluminum Metal Matrix Composite, Ionic Liquids, BMIC Recycling of aluminum metal matrix composites (MMC) via electrolysis in ionic liquids at near room temperature was investigated. The electrolytic melt comprised of 1-butyl-3-methylimidazolium chloride (BMIC) and anhydrous AlCl3. Impure aluminum composite (Duralcan MMC Al-380, 20 vol % SiC) was electrochemically dissolved at the anode and pure aluminum (>98%) was deposited on a copper cathode. The deposits were characterized by scanning electron microscope, X-ray diffractrometer, and mass spectrometer. The influence of various process parameters such as concentration of electrolyte, and applied cell voltage on the recycling process was studied. The recycling process yielded current densities in the range of 200-500 A/m2, and cathode current efficiency of about 85%. The results indicated that impurities such as Cu, Si, Ni, Fe, Mg, Mn, and SiC particles were removed as anode residue. Energy consumption of about 3.7-6.3 kWh/kg-Al was obtained at a cell voltage of 1.0-2.0 V and cell temperature of 100 ± 5°C. Low energy consumption and no emission of pollutants are the two main advantages of this process compared to present recycling processes.

Jan 1, 2005

By Pengfu Tan

A thermodynamic model and computer program, CuModel, has been developed to model the distribution behaviors of Cu, Fe, S, O, Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag, copper loss in the slag, and heat balance in copper smelting process, matte converting process and copper con-tinuous smelting process. It can be predicted for any set of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxy-gen-enriched air. This model accounts for physical entrainment between matte and slag phases. It can be used in Isasmelt process, copper flash smelting process, Mitsubishi process, P-S con-verting process and Noranda process. The predictions by the present computer model are com-pared with the known commercial data from Guixi Smelter in China, PASAR Corporation in Philippines, Horne Smelter in Canada, MIM Limited in Australia and Naoshima Smelter in Ja-pan. The agreements between the computer predictions and the commercial data are excellent. In this paper, the applications of CuModel in the copper metallurgical industries have been pre-sented. CuModel has been used by Daye Smelter and Guixi Smelter in China, and by PASAR in Philippines as well.

Jan 1, 2004

By Zhou Aiping, Lv Guozhi, Niu Liping, Wang Wenbo, Zhang Ting’an, Jiang Xiaoli

The current method used to produce sponge titanium utilizes a process cycle of magnesium metal and chlorine gas via the electrolysis of magnesium chloride. The primary issues are the high capital cost of the electrolysis process and the environmental regulations limiting high chloride concentrations. Thus, the authors have developed a conceptual method involving theelectrolysis of magnesium chloride as well as a reduction process which allows for a cycle of magnesium and chloride. In the new method, MgCl2 which was distilled during the titanium extracting process as raw material was directly pyrolyzed at elevated temperatures yielding high purity magnesium oxide and chlorine. The resulting magnesium oxide can be used in the production of magnesium metal. This work examines and compares the energy consumption and economic benefits of the Kroll method as well as the new proposed method. The results from the study demonstrated that in comparison to the traditional Kroll method, the new method provided considerable economic and environmental benefits.

Jan 1, 2014

By Xuling Chen, Yi Wang, Xiaohui Fan

"The current control method of grate-kiln iron ore oxide pellet production is lack of accuracy and normalization due to the limited detection conditions. Therefore, mathematical models of grate-kiln temperature field are presented. With calculation of gas-particle heat transfer as well as enthalpy changes of moisture evaporation and magnetite oxidation, the thermal history of pellets throughout grate-kiln process can be acquired and used for production status estimation. Taking the calculated results as well as detected data in production as inputs, process parameters such as running speed, fan opening and coal injection rate as adjusting objects, expert system for grate-kiln pellet production is outlined. And the preheating section dominated control strategy is explained. Results of production application show that the stability rate of gas temperature in gas hood of preheating section is increased from 91.0% to 94.2%, compressive strength and first grade rate of pellet are increased by 3.62% and 2.36%, respectively, while FeO content is 18.18% lower. Control guidance of this expert system can solve production anomalies effectively, stabilize grate-kiln iron ore oxide pellet production and improve pellet quality.IntroductionSteel industry in China has developed rapidly in recent years. China’s crude steel production in 2010 is nearly 627 million, which is 44.2% of the world total production. Burden with higher quality is demanded by enlargement and modernization of blast furnaces. And oxide pellet production has become a growing concern. In 2010, the total production of pellet in China is 110 million, and about 60% is produced by grate-kiln process."

Jan 1, 2012

By Hongbo Zhu, Kun Yang, Jingyan Jia, Jinhui Peng, Libo Zhang, Yi Xia

"Titanium dioxide is broadly considered as the most potential useful photocatalytic material. In this work, titanium dioxide was synthetized by microwave solid-state method and characterized by thermogravimetry-differential scanning calorimetry (TG-DSC), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The result demonstrates that through microwave solid-state synthesis, we can obtain uniform size and anatase TiO2 photocatalyst, with the precursor being Ti(C2O4)2·2H2O. And its degradation kinetic parameter of MO can reach to 0.21232.IntroductionSince Fujishima and Honda found the photovoltaic property of titanium dioxide TiO2 [l], it has been widely used in the field of pollutant degradation, virus killer and environment protection [2-5]. Compared to other semiconductors, TiO2 has the advantage of low toxicity/cost, chemical stability, excellent photocatalytic activity, and long lifetime of electron/hole pairs, thus it is considered to be a most potential useful photocatalyst material [ 6]. Solid-state synthesis of oxide nanoparticle is a new method developed in recent years, which not only overcomes the shortcomings of easily aggregation existing in traditional hydrometallurgical process, but also fully demonstrates the unique technologic advantages of without solvents, high yield, easy control, less environmental pollution in solid-state reaction [7-11]. Researches show that the new method of microwave synthesis shows a lot of advantages such as fast reaction rate, efficient, high purity of product, uniform morphology, energy-efficient, and nonpolluting [12-15].In this work, we associated microwave heating and solid-state synthesis to prepare TiO2 photocatalyst material. Its photocatalytic activity was studied in the degradation of MO queous solution. Meanwhile, the formation process as well as the crystal structure and morphology of the synthesized powders were characterized by means of chermogravimetrydifferential scanning calorimetry (TG-DSC), X-ray diffractometry (XRD) and scanning electron microscopy (SEM) techniques."

Jan 1, 2014

By Khalid Hattar, Alexander McGinnis, Buchheitm Thomas, Paul Kotula, Luke Brewer

"Understanding the effects of extensive radiation damage in structural metals provides necessary insight for predicting the performance of those metals considered for application in the extreme radiation environment. Predicting mechanical performance after long term radiation exposure is of great importance to extending the life of current nuclear reactors and for developing future materials for the next generation of reactors. A combination of finite element modeling, nanoindentation, and TEM characterization were used to rapidly determine the microstructure and mechanical properties influences of ion irradiation on a standard 3 l 6L stainless steel sample. The results of this study found that ion irradiation and small scale mechanical property testing can be used to characterize extensive levels of radiation damage structure, only when significant consideration is given to ion irradiation depth, surface roughness and polishing condition, the irradiation temperature, and many other experimental parameters.IntroductionFor either the success of next generation nuclear reactors or the extension of current nuclear reactors significantly beyond their designed lifetimes, research is needed into the degradation of the microstructure and mechanical properties governing the performance of the reactor alloys exposed to extreme environments. Although the exact dose and temperature of these nuclear reactor plans may vary, the cladding and other structural components will be exposed to greater dose and at elevated temperatures. To acco=odate these severe exposures, established cladding materials are being testing to longer exposure and new alloy compositions are being considered. [1-3] For neutron test facilities to reach 100 dpa level, exposure times often span several years, significantly limiting the down-select process of potential new materials for extreme radiation environments. Ion irradiation has been used as a technique to provide a look at the effect of irradiation damage on materials in a significantly shorter time frame. Previous work using proton irradiation provides a deep, broad, and relatively uniform defect profile compared to heavy ion irradiation; however, using this type of radiation still requires weeks to months to reach the 100 dpa level. [4] In this research, we investigated the feasibility of using heavy ion (nickel) irradiation and small scale mechanical testing to provide in a few days a first order screening technique for potential alloys that are being considered for advanced testing."

Jan 1, 2012

By Oszkar Bíró, Peter Mittag, Bernhard Aigner, Stefan Pirkeri, Philipp Glttleri

"This paper considers CFD modeling of processing and melting of small metallic particles by means of electrical heating. The particles fall continuously onto a liquid metal bath which is heated by an electric arc. After melting of the particles liquid metal is tapped.The charging behavior of the particles in the supply unit as well as in the reactor freeboard is studied by means of Euler-Euler granular simulations. The flow situation in the metal bath due to gas injection and magnetic fields is calculated by combining Navier-Stokes and Maxwell solvers. The macroscopic melting process occurring during the continuous charging of the particles is studied by kinetic laws for melting reactions. The temperature field is evaluated by balancing heat sources due to Joule's heating and heat losses due to latent heat of melting as well as convection and radiation.As a result of these simulations the fully three-dimensional flow fields of particles and gas in the atmosphere is obtained. Furthermore the flow field as well as the magnetic field in the metal bath can be studied. As a main result the three-dimensional concentration field of the still unsolved particles in the liquid metal can be evaluated.IntroductionIn this paper a metallurgical process for melting small iron particles is investigated by means of CFD-simulations. In a first process step the preheated and already mostly reduced iron particles fall continuously into the reactor through a vertical tube mounted at the lid of the furnace. In a second step the particles are melted in the liquid metal bath. Meanwhile the melt is heated by electric arcs to provide the heat needed for melting the incoming particles.In Figure I a sketch of the geometry setup considered in this paper is provided. The particles fall from a height of approximately 12 meters onto the bath surface in the center of the furnace. The melt is heated by electric arcs that are placed symmetrically around the center axis."

Jan 1, 2001

By Naixiang Feng, Shaohu Tao, Zhihui Wang, Yuezhong Di

"A novel vacuum aluminothermic reduction lithium process was developed in present work which used lithium carbonate, alumina and calcium oxide as raw material. The process mainly contained three steps. The first step is that LiA102 clinker is prepared in ambient environment, then metal lithium is vacuum extracted from LiAl02 clinker with aluminum power as reducing agent, and the last step is that alumina is leached from the reduction residue with a mixture of sodium hydroxide and sodium carbonate. The results show that the lithium reduction ratio can be over 95% under the conditions of reduction temperature 1423K, reduction time 3h, and aluminum excess 20%. The main components of reduction residue are CaO· Al203 and 12Ca0·7Alz03. The alumina leaching rate of calcium aluminate in residue is over 80%. High-whiteness aluminum hydroxide can be obtained by carbonation precipitation of the reduction slag leaching solution.IntroductionWith a density about half of water, lithium is with the lowest density of all solids, mere 0.5 g/cm3 at 20 °C [l]. Lithium is widely used in aerospace, aviation, nuclear-generated power and electric battery industry. Nowadays, over 90 % of the world's primary lithium is produced by molten salt electrolysis [2-4]. But the development of molten salt electrolysis will be effected by some factors: cost, environment, and so on. Vacuum thermal reduction may be used extensively in future because of its low-energy consumption, high-purity and short-cycle."

Jan 1, 2013