Search Documents

By Ross R. Bhappu

Anticipating a major power cost increase in 1990, Cyprus Copper Company decided to modernize the Miami Smelter at a cost of $92.5 million. The modernization project included the addition of an Isasmelt vessel for use as the primary copper smelter and the modification of the existing electric furnace to a slaglmatte separating vessel. The project was completed in June of 1992 and is currently operating at close to its design capacity. This paper provides a summary of the decision making process, a description of the project, a summary of start-up problems and solutions and the current status of the smelter operation.

Jan 1, 1994

By Rick Honaker

Rare earth elements (REEs) contained in coal and associated mineral matter exist in several forms including micro-dispersed minerals, ion adsorption onto clay surfaces, and chemically bound. Tests found that REEs can be effectively recovered from certain components of three coal sources by leaching under mild conditions followed by solvent extraction. A range of pH values were evaluated at solution temperatures of 25 and 75 °C. When using 1.2 M of sulfuric acid, nearly 85% recovery of the REEs was extracted from the middlings material collected from an operating plant. Acid leaching of a second middling source from another plant resulted in 60% of the total REEs being recovered under the same leaching conditions. Solvent extraction treatment of the leachate produced from six different coal sources resulted in products containing up to 50% total REEs from feedstocks starting with around 300 ppm.

By W. Drummond

The cooling of smelter gases by air dilution, adiabatic evaporative cooling and indirect heat exchange is discussed with reference to the ,process, to the subsequent cleaning of the gas and to the use of the heat extracted from the gas. The method of reducing the effect of acidic ,sulphide formation on the corrosive properties of the gas and the dust and the development of surface cleaning mechanisms are discussed. The development of indirect recuperators using air, water or steam cooling, made 'possible by the control of surface fouling is traced. The application of the modern Waste Heat Boiler to the new sulphide smelting processes is discussed with respect to the natural and forced circulation concepts. Case histories are presented to illustrate mistakes made with respect to designs produced without recourse to sensitivity analysis and without an appreciation of "worst process conditions".

Jan 1, 1992

By Hans Korfmacher

Product take-back regulations implemented in Europe have presented significant challenges to the consumer electronic product and battery industries. Initially companies established single compliance organizations within individual Member States. These programs met business needs but were inefficient and costly. They were protected from pressures of marketplace competition and could not leverage economies of scale. In order to address these problems P&G, Hewlett Packard, Sony and Electrolux conceived a pan-European compliance organization to collect waste electronic equipment Europe-wide. This organization, called the European Recycling Platform (ERP), operates in competition with existing national compliance systems. Since 2005 ERP has collected 800,000+ tons of waste electronic products and delivered millions of dollars in cost savings. This presentation reviews the steps needed to establish successful competitive collection organizations that provide sustainable recycling at the lowest cost.

Jan 1, 2010

By Marcello M. Veiga

Informal gold mining operations in the Amazon emit about 100 tonnes of mercury annually because of poor amalgamation practice. Lack of information and the complexity of mercury transformations hinder effective action to prevent such pollution and/or monitor its extent. In the past, mathematical equations have been formulated to deal with the correlation of natural variables and mercury in biota but often, the error range is too great to provide useful models. Projection of physico-chemical variations in an environment subjected to mercury emissions onto the extent of bioaccumulation is fraught with many uncertainties and unknowns such as internal correlations between variables and the site-specific nature of biota contamination. Often assumptions about closed systems are invalid when applied to natural environments. This work presents a heuristic approach to this problem in which amalgamation methods and natural variables are dealt with using an IF-THEN rule-based system that concludes about levels of emission and risk of bioaccumulation. The system is able to handle uncertain or vague data and yet still provide useful output. Belief in mercury oxidation or dangerous conditions are examined using Fuzzy Logic techniques and Inference Equations. These belief levels are derived from thermodynamic equilibrium data together with field observations of natural variables. This procedure can reduce the need for sophisticated analytical equipment and can provide information and diagnosis to non-technical people.

Jan 1, 1994

By Reinhard Bott

The Companhia Mineira de Metais (Brazil) runs a Zn-recovery plant in Tres Marias, federal state Minas Gerais, Brazil. The Zn-production is about 65,000 t/a, This corresponds to a concentrate throughput of about 255,000 t/a with a Zncontent of about 29.5 % at an output of 85 %, The plant is run continuously 360 d/a and 24 h/d, respectively. From this it can be concluded that: Input: approx. 650 - 700 t/d ore-concentrate and approx. 29 t/h ore-concentrate, respectively.

Jan 1, 1990

"Hematite pellets were electro-deoxidized to iron in molten sodium hydroxide to produce iron containing about 10-wt % oxygen. The anodic reaction was the evolution of oxygen on an inert nickel anode. Before the electrochemical reaction, there is a reaction between sodium hydroxide and ferric oxide to form sodium ferrite and, in order to compensate for the reduction in sodium oxide content, 1 wt % sodium oxide is added to the melt. In a laboratory cell, the cell voltage was 1.7 V with a current density of 5000 A m-2, a current efficiency of 90% and an energy consumption of 2.8 kWh kg-1.Introduction The iron and steel industry contributes about 2.3 bn tonnes/annum of the carbon dioxide to the atmosphere, which is about 10% of the total, and some believe that, in order to prevent a catastrophic rise in the earth’s temperature, carbon dioxide emissions must be reduced by 50% come 2050. However, by 2050, it is likely that the iron and steel industry would have grown significantly so that the production may have risen to 2 or 3 bn tonnes/year so in order to meet the 50 % reduction on today’s figure, the carbon dioxide may have to be reduced to 25% or less, which is a very demanding requirement. There are probably three ways of reducing the carbon dioxide output:1. By capture and sequestration, but this may be technically very demanding.2. Reduction using hydrogen in place of carbon."

Jan 1, 2009

By E. I. Gedgagov, A. V. Tarasov, V. M. Paretsky, A. D. Besser

"Hydrometallurgical technology and equipment have been developed in the Gintsvetmet Institute (Moscow, Russia) for processing of rhenium-containing alloys waste to produce commercial- grade metal products with recovery of all valuable components. The technology is based on waste treatment with hydrofluoric acid with subsequent decomposition with nitric acid at pH = 1 to 1.5 to ensure maximum degree of rhenium conversion to the liquid phase of pulp. Some experimental lots of ammonium rhenate and ammonium molybdate were produced at a pilot plant. The following main techno-economic performance values have been achieved when processing grinding residues (balance-based tests were conducted with a lot of SP-2 alloy waste) to produce ammonium rhenate of high purity, as well as tantalum-niobium, nickel-cobalt and tungsten-molybdenum concentrates: rhenium recovery of 92.3% into a commercial product from grinding waste; production cost of 170-210 US Dollars per 1 kg of rhenium in commercial-grade ammonium perrhenate taking into account its recovery; tantalum and niobium recovery of 75- 77% into bulk concentrate; nickel and cobalt recovery of 88-89% into a mixed concentrate; tungsten and molybdenum recovery of 88% to 91% into concentrate. Introduction During the recent years the use of rhenium has been increasing at a fast pace worldwide [1]. The growing prices for this refractory metal are an essential factor encouraging collection and processing of rhenium-containing wastes. Double-component waste, such as molybdenum- rhenium or tungsten-rhenium alloys can be readily decomposed and the process of rhenium recovery does not cause, therefore, any difficulties. The main separation of metals takes place at the stage of waste digestion with acid, because molybdenum and especially tungsten remain in precipitate in the form of hydrated oxides and rhenium reports in the liquid phase, from which it can be easily extracted by solid ion-exchange or solvent extraction techniques. However, most of rhenium is contained in super-alloy waste [2]. Such waste has different contents of valuable components, such as tantalum, niobium, molybdenum, tungsten, cobalt, nickel, chromium and other metals. The basis of all such super-alloy waste is nickel. Refractory metals in the super- alloy composition are in the form of metallized target-oriented eutectics, and due to this reason hydrometallurgical decomposition of such alloys is a difficult technological task."

Jan 1, 2008

By Mark Tjerkstra

In ,1993, the WMC Resources Ltd.-owned Kalgoorlie Nickel Smelter, underwent a capacity upgrade. This capacity increase was offset by .air quality control restrictions limiting the smelter's availability to 80%. As the direct. result of this limitation, WMC Resources Ltd commissioned a double absorption contact ,acid ,plant for the desulphurisation of furnace waste gas in August 1996. The history and the impact of the acid plant on S02 emissions and air quality is reviewed. General descriptions of the other aspects of the Kalgoorlie Nickel Smelter's Environmental Project are also included in the paper. Information on 'the design features? and operating practices that relate to or contrast with practices at operations visited by KNS personnel prior to acid plant commissioning provide the paper's focus. Smelter operation has changed markedly from unstable operation prior to 1997 to continuous" operation with little down time due to mechanical or process failures resulting in increased smelter availability to more than 90%

Jan 1, 1998

The U.S. Bureau of Mines investigated CaF2-assisted H2SO4 leaching to extract Mn from domestic silicate manganese resources. A pyroxmangite ((Mn,Fe)Sio3) ore containing, in pct, 34 Mn, 23 Si, 3 Ca, and 1 Fe was leached at 90° C for 3 h in a solution containing, in g/L, 12 Mn, 140 H2SO4, 130 (NH4)2SO4, and 5 CaFz. Manganese extraction of 92 pct was achieved. Manganese of greater than 99 pct purity was prepared by electrolyzing the purified pregnant solution at a current density of 50 mA/cm2. The current efficiency was 65 pct.

Jan 1, 1991

By John M. Boyle

The use of high vacuum mercury retort recovery as a safe and effective means of removing mercury from mercury hazardous waste solids rendering them non-hazardous and recovering mercury suitable for recycling.

Jan 1, 1995

By P. N. Anyalebechi

"The effects of solidification rate, initial melt hydrogen concentration, and grain refining on porosity formation in aluminum alloy 2024 have been investigated with unidirectionally cooled laboratory-size ingots. The ingots were prepared from melts containing hydrogen concentration of 0.059-0.27 cm3/100 g and solidified at 0.2-37 °C/s. As expected, the amount of porosity, average pore size, and pore number density increased with increase in melt hydrogen concentration and decrease in solidification rate. However, the effect of solidification rate was greater at the very low melt hydrogen concentration (0.059 cm3/100 g). These results are consistent with reported effects of solidification rate and melt hydrogen content on porosity formation in other aluminum alloys. Interestingly, addition of grain refiner slightly increased the amount of porosity and the average pore size, especially at solidification rates above 1°C/s. IntroductionIn shaped castings and wrought products fabricated from ingots, billets, bars, or slabs of aluminum and its alloys porosity formation is a problem. This is because it compromises their tensile strength, fracture toughness, and fatigue properties [ 1-18]. The pores are usually the crack initiation and propagation sites [6,8,9] and the largest pores tend to dictate the fatigue life of the aluminum products [9,10,14]. Porous regions within an aluminum product probably yield first due to the reduced tensile load bearing capacity, causing the concentration of the strain near the voids which subsequently results in premature fracture. In aluminum alloy ingots, billets, bars and slabs porosity formation is particularly problematic because of its persistence through fabrication and potential for reappearance or exacerbation during subsequent thermal treatment processes before and/or after fabrication [19]. In fact, persistence of microporosity is a serious problem in large thick plates of wrought aluminum alloy products that must be rolled from correspondingly large direct-chill or electromagnetic cast ingots. Some of these thick plate products are machined into large aircraft components that are required in service to withstand multi-directional stresses and to possess high fatigue strength, fracture toughness, resistance to stress corrosion cracking, and strength in the short-transverse direction [1,20]."

Jan 1, 2011

By Noriaki Kurita, Norihiko Fulcatsu, Teruo Ohashi

"An electrochemical sensing device for hydrogen in molten metal has now been available owing to the development of the proton conducting solid electrolyte made of ceramics of metal oxide. The structure of the sensor and the theoretical limitations of its applications are discussed based on the electrochemical properties of the electrolyte used. The practical performance of the sensor is reviewed from the results of test measurements at the plants of aluminum and copper melting industries. The effectiveness of the sensor to the process control of continuous casting of copper is also discussed.IntroductionSince the in-line monitoring of the amount of oxygen dissolved in molten metal was realized by using the oxygen concentration cell based on zirconia solid electrolyte a similar method has been expected to be developed for sensing of hydrogen, which is a very important element of gas species in liquid metals, especially, in aluminum and copper. In 1981; Iwahara and coworkers found the dominant proton conduction at a high temperature in some perovskite-type oxide (1). Since then, the effort has been made to apply this proton conducting material as the electrolyte of the hydrogen concentration cell for high temperature use. The hydrogen sensor for liquid aluminum of this kind was first produced in 1991 (2) and released commercially from TYK Co., Ltd. Recently, we have developed the mother one usable at higher temperature such as copper and silver melting processes (3). In this note we discuss their structure, design and applicable limitations based on the electrochemical properties of this new type electrolyte. The performance of the sensor and benefit to use it to control the melting process is also discussed"

Jan 1, 2000

By Peter Hayes, Evgueni Jak, Ata Fallah Mehrjardi

Modern analytical tools, such as electron probe X-ray microanalysis (EPMA), are used in experimental characterization of phase equilibria and microstructures of complex slags. Integrated thermodynamic computer packages, such as FactSage, are used to provide more accurate descriptions of complex slag systems. These advanced methodologies have been applied to characterize dynamic steady state freeze linings in slag systems using submerged cold finger probes at controlled laboratory conditions, establishing the effects of bath chemistry, temperature, heat extraction rate and bulk fluid flow. It has been found that stationary freeze lining deposit interface temperatures at steady state conditions can be lower than the bulk slag liquidus temperature, and that stable operation below the liquidus is possible. A conceptual framework has been developed to explain the phenomenon and the range of interface temperatures that can be obtained in dynamic steady state conditions. These findings have important implications for the design of freeze linings and possible improvements to high-temperature metallurgical operations.

Jan 1, 2014

By C. J. Newman

Production levels at the Kidd Creek copper operation increased during the 1980's by expansion of both the smelter and refinery and by major modifications to equipment which was causing bottlenecks. As a result, there was a significant reduction in the unit cost, some manpower reductions and hence a significant increase in productivity. In the last two or three years, there have been no major expansion projects leading to unit cost reductions and yet these have still been attained. This has been achieved by the development and implementation of various techniques designed to maximize the inherent potential of the operators and maintenance employees. This paper will initially describe the operation but will then place emphasis on employee involvement through such methods as idea awards, incentive schemes, loss control and continuous improvement programs. Organizational changes are discussed, particularly with reference to changes from the traditional operator role to one which encompasses maintenance skills and to cross-training of maintenance employees into multi-discipline fields. The effect of these changes are discussed by a review of the salient plant parameters of safety, production levels, cost and quality.

Jan 1, 1993

By Jim Hardy, Tim McKnight

"The thermal mass flow controller, or MFC, has become an instrument of choice for the monitoring and controlling of process gas flow throughout the materials processing industry. In the semiconductor industry, these MFCs are used on over 70% of the processing tools. Reliability and accuracy are major concerns for the users of the MFCs. Calibration and characterization technologies for the development and implementation of mass flow devices are described. Sources of inaccuracy in process gas handling are described, and a model to correct for these inaccuracies is outlined. A gravimetric calibrator is described that allows flow sensors to be calibrated in corrosive, reactive gases to an accuracy of 0.3% of reading, at least an order of magnitude better than previously possible. All described capabilities are implemented in a Department of Energy User Facility which is available to industry and universities to test and develop gas flow sensors and controllers and evaluate their performance related to environmental effects, reliability, reproducibility, and accuracy.IntroductionMaterials processing is at the heart of semiconductor manufacturing. To make today's advanced integrated circuits, silicon wafers are subjected to over 200 process steps. Most of these steps involve processes such as etching, implanting, diffusion, annealing, deposition, and lithography (resist deposition and hardening). Often one or more process gases are used to complete the process step. To achieve the quality and performance required in the micro devices, accurate measurement and control of these gases is essential. The Oak Ridge National Laboratory (ORNL), in conjunction with the semiconductor industry, has been working to improve process gas measurement and control accuracy and reliability. Standardized test methods have been developed to characterize and benchmark the performance of mass flow controllers (MFCs), the method of choice for monitoring and controlling gas delivery. Testbeds have been designed and fabricated to produce repeatable and accurate data using these standards. Baseline testing was performed along with development of a unique mass flow instrument, the gravimetric calibrator."

Jan 1, 1997

By Marco V. Ginatta

Current world production, 60'000 ton/y, is exceedingly too small for titanium's extraordinary combination of favorable properties; it should be 1,000,000 ton/y (7% of stainless-steel). Prices that competitively sustain that sales volume are achievable only with electrolytic production, as it is for all other commercial nonferrous metals. But titanium does not have its commercial electrolytic plants yet, because of producers decisions and strategies, scientists works, industrial problems with chloride process, lack of consumers sponsors. Fluoride high temperature process has the advantages of aluminum electrolysis, plus other favorable characteristics specific to titanium and its feed material. One electrolytic titanium potroom replaces several different plants used for sponge production. Production of titanium ingots with zero defect is achieved. The solidified cathode rectangular slabs are suitable for direct rolling.

Jan 1, 2001

By Roderick Guthrie

Gas injection into liquid steel baths is widely practiced, ever since the early days of Bessemer’s pneumatic steelmaking process. What has not been fully appreciated is the critical role of bubble sizes for delivering higher quality commercial steels than is presently possible. This was first proposed by Prof P. Hayes and his research group. Using a full-scale water model of a typical 4-strand Ladle-Tundish-Mold system, we demonstrate the potential advantages of modifying a typical ladle shroud, to generate microbubbles within the water flowing into the tundish. This is possible by taking advantage of high shear rates and turbulence kinetic energy available in that region. These microbubbles enhanced the removal of “micro-inclusions” (hollow glass microspheres) in the 5–50 micron size range, to the upper surface of the tundish. There, they were absorbed into an overlaying “slag” phase. Accompanying CFD studies confirmed that no microbubbles in the size range generated (500–900 μm), pass through the submerged entry nozzles into the moulds.

By C. J. Beyke

In recent years recycling of household batteries has received increasing attention, primarily for environmental reasons. This article reviews the major battery types and some of the technologies available to recycle them. It also discusses issues such as collection and sorting which are related to battery recycling in the United States. Finally, results from research being conducted by the U.S. Bureau of Mines on the reclamation of nickel-metal hydride, alkaline, and zinc-carbon batteries are presented.

Jan 1, 1995

By T. H. Eyde

Several hundred natural zeolite deposits occur in Tertiary and Cretaceous age formations of the western United States. Most of the large deposits are altered vitroclastic tuffs. Many of these deposits consist of a matrix of a high purity zeolite mineral or minerals in which fragments of unaltered rock are imbedded. These deposits represent an extensive resource of zeolite minerals which can be beneficiated to a consistently uniform, high quality product. The beneficiated natural zeolite products will possess many advantages over the selectively mined, unbeneficiated natural products currently being produced. These advantages will include: uniform particle size, high purity, consistent quality, high brightness, low iron content, high attrition resistence, uniform cation exchange and adsorption capacities, and low price.

Jan 1, 1981