Search Documents

By Xingjian Gao

The mechanical properties of a low carbon low alloy steel in the austenite and _-ferrite regions have been examined by thermal-tensile tests using a Gleeble-1500D system at temperatures in the range 600oC to 1300oC and at a strain rate of 10-3/s; these being the conditions that apply to the unbending operation during the continuous casting of steel. The yield strength and tensile strength of steel decreased with increasing test temperature and the embrittlement zone occurred in the temperature range 800oC to 970oC. In the embrittlement zone, the fracture surfaces and microstructures of the tensile specimens were examined by scanning electron microscope. The results showed that the cause of the embrittlement at 950oC in which the minimum %R of A was around 36% is the second phase particles precipitated along the _ grain boundary during deformation leading to inter-granular brittle fracture.

Jan 1, 2010

By H. Aminian

Copper electrowinning (EW) is an important process in connection with the solvent extraction to produce pure and marketable copper cathodes. A phenomenological model was developed to simulate the copper electrowinning process. The simulator is used to predict the operation of the Mines Gaspe pilot plant electrowinning cells put in operation in 1996. Results confirm the potential of the simulator that would subsequently be used for student training, process optimization and assessing the performances of control strategies.

Jan 1, 1999

By G. Roderick Eggert

Material criticality reflects the degree to which a raw material is both necessary and subject to supply-chain risks. This study compares the criticality of selected raw materials from the differing perspectives of the manufacturing sectors of China, the European Union, Japan and the United States.

By Nobuhiro Shinihara, Makio Naito, Keizo Uematsu, Tadashi Horta, Hiroya Abe, Masataro Okumiya

"A significant variation of strength was noted in silicon nitride ceramics made through the powder compaction processing with minor processing changes. The relevance of the fracture strength to the microstructure was examined in these ceramics. In the examination of microstructure, the ceramics were made into thinned specimens, and their internal structures were observed with an optical microscope in the transmission mode. This technique can distinguish a difference in microstructure associated with the minor processing changes. The strength of all ceramics examined in this experiment was qualitatively correlated with the -pore size distribution in the specimens. Clearly, the elimination of these detrimental defects will enhance the reliability of ceramics.IntroductionIn ceramics made through powder processing, a variation of properties is often encountered [l ,2]. This brings a major problem on producing reliable and cost-effective ceramics. The variation is often ascribed to the changes in the characteristics of defects. However, there is no clear evidence f\)r this explanation due to the lack of an adequate tool for identifying the defects determining the properties. Details of the origin of the variation have still been poorly understood.A new technique is very promising for clarifying the origin of the variation [3,4]. This has very high potential in detecting minor differences in structure for .engineering ceramics. With this technique, ceramics are made transparent with its thinning down to about 50 µ m and their internal structures are observed with various types of optical microscopes in the transmission mode. The characteristics of the defects determined through this approach were found to be directly related to the strength of the ceramics [4-6].The objective of this study is to clarify the ongm of fracture strength of silicon nitride ceramics. This material is representative of high performance ceramics, and the origin is of great practical interest. For this study, silicon nitride ceramics with minor changes in processing condition were prepared. Specific feature focused in this study is the difference of large pore structure determined with the new technique and its relevance to the strength of the silicon nitride ceramics."

Jan 1, 2000

By Dan Adams

A number of gas-liquid processes require high intensity agitation systems to provide uniform blending and dispersion of reactants in order to achieve desired end products. Processes such as hydrogenation, fermentation, and minerals processing have used conventional down pumping or radial agitation systems with some success. In 1996, LIGHTNIN introduced the concept of Up-Pumping to the industrial marketplace as an improved mixing technology for these applications. For processes requiring gas-liquid mass transfer, such as those listed above, conventional mixing technology requires the use of gas introduction devices (sparges) below impellers. These devices can be a maintenance concern due to plugging and erosion in the presence of solids. Up-Pumping impeller systems are able to draw in a significant amount of gas from the headspace, much more so than conventional vortexing impellers designed for headspace gas incorporation. This paper will demonstrate the effectiveness of Up-Pumping impeller systems that have the potential to eliminate need for sparge devices entirely. It demonstrates the ability of Up-Pumpers to re-entrain gas for higher utilization compared with conventional impeller technology. This is significant in applications using costly gases such as enriched oxygen or hydrogen, reducing overall operating costs of production.

Jan 1, 2003

By J. P. Ibáñez

The uptake of copper from extremely dilute aqueous solutions by alginate in the form of protonated dry alginate beads was investigated. Barium was used to cross link the alginate forming the beads. The effect of various experimental parameters such as pH and metal ions concentration on the uptake of copper were studied. The uptake was strongly dependent on the Cu-bearing solution pH up to a value of 4.5. A removal of 100% o was achieved when the initial concentration of copper was as low as 8.0 mg/L. The maximum uptake, i, e., the loading capacity, was found to be 167 mg of copper per g of beads. The mechanism governing the removal of copper was found to be ion exchange between protons of the alginate beads and cupric ions of the solution. For this ion exchange process a molar ratio, d[H+]/d[Cu2+], of 2.0 was determined. EPMA-EDX analysis of the Cu-loaded beads showed a uniform distribution of the ions throughout the structure of the alginate, regardless the solution pH. This may suggest that this sorbent material is a porous ion exchanger having high permeability and capacity. The uptake of copper and of the heavy metals cadmium and zinc by this sorbent is compared.

Jan 1, 1999

By Rolf R. von Oppenfeld

Onsite hazardous waste processors often find obtaining a Treatment Storage and Disposal (TSD) permit one of their first major challenges. Some processors may spend the time and money required by the permitting process, only to find out later that a permit was not necessary. This paper will present and analyze four strategies that processors may use to avoid obtaining a TSD permit. Some facilities will be able to remove their waste streams from RCRA's oversight by ensuring the material is not "hazardous" waste. Parties that treat waste while it is in process may be able to avoid generating "waste" altogether. Certain treatment facilities have been specifically exempted by EPA. Finally, treatment of waste while it is in generator storage tanks may be allowed without a RCRA TSD permit. Hazardous waste point of generation, an important determination relating to these strategies, will also be discussed. Generators and processors will find this paper useful when evaluating their permit exemption potential

Jan 1, 1996

A simulation of a capper concentrate smelter was built with a capacity of 450,000 tons per year. The system's components to simulate were three : a Reverbetory furnace, a Wiente ' s modified converter ( TMC ) and two cranes. The system was classified as dynamic, stochastic and discrete. In the simulation language choice it was concluded that the most advantageous one was GPSS/H. The model verification was done through the interactive Debugger that the language has and the statistical validation was done through the result variables of sane activities, that as a whole characterize the system (charged matte and charged concentrate to the TMC, skimming white metal and skimning slag). The validation was done comparing the simulation results of these variables with the ones obtained for those variables in a specific month in the smelter. The comparison consisted in a difference of means test and in all cases the equality was accepted with a 95% of confidence. The animation tool was PROOF, a general purpose animator, that is used after processing the simulation.

Jan 1, 1994

By M. R. Dahm

The demand for low sulfur steel by steel manufacturers and their customers has been steadily increasing for 25 years. Historically sulfur has been controlled by various means and with various additives but lime-magnesium external desulfurization of hot metal has become established as the dominant method in North America today. Magnesium powder produced from primary magnesium ingot has been the major source or raw material. However, periodic increases in the price of this commodity have encouraged producers to look to secondary magnesium for an alternate source of magnesium. Secondary magnesium from post-consumer scrap can be cleaned, sized, and prepared to produce a high quality magnesium reagent for use in hot metal desulfurization at a lower cost than material processed from primary ingot.

Jan 1, 2000

By Shengli Wu, Wei Huang, Xinliang Liu, Kaifa Zhang

The slagging behavior, the phase of primary blast furnace slag and its transformation law of structure for the single furnace burden were studied in this paper. The results showed that the formation of primary slag was controlled by CaO/SiO2, Al2O3 content, MgO content, reducibility, iron content and porosity of the furnace burden. Fayalite (2FeO•SiO2) was easily formed from acid ferrous furnace burden while kirschsteinite (2(Fe,Ca)O•SiO2) was produced from alkaline ferrous furnace burden

Jan 1, 2015

By Sijun Li, Bingyu Zhang, Haitao Zhou, Zhendong Zhang, Guofei Si, Xianghua Liu

"Hot compression test of Nb microalloyed coiled tubing steel is performed on Gleeble3500 at 1123K—1373K and strain rate from 0.001 to 5s-1. It is found that flow softening occurs and the flow curves exhibit a peak with a characteristic of dynamic recrystallization (DRX) and change with temperature and strain rate significantly. The peak stress and peak strain are dependent on the Zener-Hollomon relationship with activation energy of 390 KJ/mol. On the basis of Avrami equation and the Zener-Hollomon parameter, it is obtained that the dynamic recrystallization kinetics equation with which the calculated and measured recrystallization fraction is very close. On the results of hot compression test, the Nb microalloyed coiled tubing steel is rolled by Thermo-Mechanical-Control-Processing (TMCP), and it is obtained that the yield strength and tensile strength of Nb microalloyed coiled tubing steel are 565MPa and 685MPa respectively, and the elongation percentage is 30.1%.IntroductionCoiled tubing is widely used in oil field for well logging, well completion, drilling, work over and other operation in various fields to solve a number of conventional operating techniques problem which are difficult resolved, and it plays a more and more important part in exploration and production at oil field. [1] It will improve the efficiency of exploration and exploitation, studying, developing and using coiled tubing technology. Therefore, the development of domestic coiled tubing materials and manufacturing technology are great significance. It is well known that Coiled tubing has relatively poor working conditions and complex force state. So, the coiled tubing needs satisfier a kind of high strength, high plasticity, and corrosion resistant under complex oil gas condition. As the coiled tubing technology developed, the level of the coiled tubing steel is from CT55 originally to CT90 and CT100, and the corresponding tensile strength is 483MPa-758MPa. [2, 3]"

Jan 1, 2012

By Matti Hämäläinen

Outokumpu has developed a new chloride leaching process, HydroCopper?, for copper concentrates. The process utilizes the cupric ion as oxidant, which is able to dissolve chalcopyrite. After solution purification monovalent copper is precipitated as cuprous oxide, Cu2O, using sodium hydroxide. Copper product is produced from Cu2O by reduction, melting and casting. An essential part of the new process is chlor-alkali electrolysis, which regenerates the reagents used. All impurity metals are removed before Cu2O precipitation, because otherwise they would report to the copper product, impairing its quality. A multistage solution purification scheme has been developed consisting of firstly, chemical precipitation of impurity metals by pH increase, secondly, cementation of silver and thirdly, removal of trace multivalent ions using ion exchange. This paper describes the characteristics of solution purification in the HydroCopper? process based on the laboratory tests and pilot runs made by Outokumpu Research Oy.

Jan 1, 2003

By Laszlo Kadar, J. D. Lavers

"In the continuous casting of aluminum killed steel, the tundish nozzle often experiences clogging problems. Water model studies have shown that the clogging problem is dependent on the flow pattern in the nozzle entry region. In particular, the flow can separate at the entrance to the nozzle, leading to the development of a recirculation region. Although a nozzle can be designed such that no recirculation develops, even a small misalignment from the vertical positioning of the nozzle may render the design ineffective.To reduce the possibility of nozzle clogging, the recirculation zone must be reduced or eliminated. This may be achieved by moving the fluid downwards or raising the turbulence level in the separation region. In the case of a tundish nozzle, it is proposed that this can be achieved by using electromagnetic forces.To generate the required electromagnetic force, two systems are considered. The first is based on injecting a DC current; the second by using electromagnetic induction. Both methods are described in this paper. Order of magnitude calculations are provided to illustrate that both methods are essentially feasible. The performance of each method in terms of modifying the turbulent flow characteristics in the nozzle entry region is then examined using a numerical model. It is shown that both methods can greatly reduce the recirculation zone. A cylindrical nozzle was chosen for the model studies since it represents a worst case situation.On the basis of the model studies, it can be concluded that whereas both of the proposed methods have the potential to reduce the troublesome recirculation zone, the induction method appears to be simpler in terms of practical implementation."

Jan 1, 1999

By A. K. Kyllo, N. B. Gray, B. N. McCurry

"Dynamic control of the formation of a solidified layer between a pipe wall and a flowing melt enables the flow rate to be adjusted in real time. This solidified layer can be generated by using a coolant on the outside of the pipe wall to remove the required heat. The coolant, and hence the solidified layer, can be controlled remotely. The dynamic behaviour of the solidified layer was investigated by both physical experiments and mathematical modelling. The mathematical model has been developed using a finite difference technique to describe conduction through the pipe wall and solidified layer. Results from the model were consistent with previous steadystate experimental results using molten lead. Experiments are currently being carried out using molten tin in a recirculating circuit with a cooling system that is instrumented for accurate computer control to validate the model. The circuit is designed for flowrates of up to 24 kg/s (86 tph) of molten tin. Steady-state and dynamic predictions were made for the current rig.Industrial SignificanceThe current method of choice for tapping slags, metals and mattes from many metallurgical furnaces is using an oxygen lance to open the taphole and using a clay plug to close it. There are, however, some significant drawbacks in this method. The heat generated by the oxygen lance erodes the refractory lining of the taphole, as well as the clay plug, and the furnace products themselves corrode the taphole. Using an oxygen lance is also a significant safety hazard to the operators as they must work in close proximity to the furnace and be subjected to a shower of sparks while opening the taphole. Also, the flowrate of material through the taphole cannot be controlled online as the diameter of the opening cannot be varied easily. This feature means that the level of product in a furnace cannot be kept constant."

Jan 1, 1999

By G. A. Brooks

Reactive ball milling has been proposed as a new route for producing carbides from oxides through carbothcrmic reduction. It is claimed that through milling oxide and graphite powders to the nanoscale, amorphous materials with very high reactivity are formed, that allows for easy transformation of the starting material to another in a subsequent thermal process. Thermodynamic analysis of this proposed process suggests that unless particle sizes are reduced to below 10nm, then reduction in size alone cannot explain a change in the stability of oxides. Even with nanometer scale powders, the products formed need to have a lower total surface energy than the reactants before a chemical change will occur. A model developed by Bhattacharya and Arzt for predicting localized temperature changes based on milling conditions suggest that temperarure rises less than 400 K will be achieved in laboratory conditions. The present calculations suggest that nanometer scale powders formed through high speed ball milling (>10 mls) may have undergone a process analogous to melting and quenching. Further work is required to fully distinguish these features.

Jan 1, 2003

By Takao Yasugi

The majority of copper in the raw material migrates to the de-copperized dross that forms when the crude lead produced in the blast furnace is treated in the de-copperizing process. The de-copperized dross is treated in the electric furnace producing matte, speiss, and crude lead. The de-copperized dross also contains the silver. Therefore, it is important to improve the rate of silver migration to the crude lead. For this reason, the behavior of silver between the matte, speiss and crude lead phases was examined. At the same time, several tests to improve the percentage of silver migrating to crude lead were conducted.

Jan 1, 2003

By Tadafumi Adschiri

"Supercritical water can provide an unique reaction atmosphere for synthesizing metal oxide nanoparticles. Due to the drastic change of properties of water around the critical point, including density, dielectric constant and ionic product, the reaction phase with O 2 or H2 gas and the reaction rate and equilibrium can be varied to synthesize new materials or define particle morphologies. In this work, hydrothermal crystallization experiments are performed with several types of flow apparatus that allow convenient manipulation of variables such as temperature, pressure, and residence time. Key features in the flow modes and material preparation are discussed. The proposed supercritical hydrothermal synthesis method has the following desirable features: i) nanoparticles can be produced, ii) morphology of the produced particles can be controlled with small changes in pressure or temperature, and iii) a reducing or oxidizing atmosphere can be applied by introducing oxygen or hydrogen or other gases. An overview of this method is given for functional material synthesis of significant industrial interest including barium hexaferrite magnetic particles, YAO/Tb phosphor fine particles and lithium cobalt fine crystals.IntroductionHydrothermal crystallization, a method of metal oxide formation from metal salt solutions, is typically used at temperatures ranging from 373 K to 473 K. We are developing a new process for hydrothermal crystallizations that uses temperatures in the range of 673 K to 723 K, which is just above the critical temperature of water1 • 8 • In this work, we refer to this process as supercritical hydrothermal synthesis. The supercritical state of water allows one to vary reaction rate and reaction equilibrium by shifting the dielectric constant and solvent density with pressure and temperature. From of our research on material production in supercritical water, we have identified the following specific features of the supercritical hydrothermal synthesis method: (i) ultrafine particles can be produced, (ii) morphology of the produced particles can be controlled to some extent with pressure and/or temperature, and (iii) a homogeneous reducing or oxidizing atmospheres can be provided by introducing gases, such as O 2, H2, H2O 2• and so on.1"

Jan 1, 2000

By Guodong Lai, Shixing Wang, Lijuan Chu, Jinhui Peng, Zebiao Zhang

"The beneficiation of poor manganese ores containing phosphate gangue is very difficult by conventional processes, because of the similarities in the physico-chemical properties of the constituent minerals. The shaking table gravity concentration process and concentrated strong acid selective intensified leaching process were used for dephosphorisation of Yunnan manganese ore. The leaching process was effective. The effects of intensified leaching time, solid-liquid ratio and particle size were investigated. The relevant leaching factors were optimized as -0.125+0.088 mm particle size with 68% nitric acid for 24 h when using a solid-liquid ratio of 1:1 at room temperature and atmospheric pressure. Under these conditions, the P/Mn ratio was reduced from 0.0107 to 0.0056, and the grade of manganese was increased from 12.32% to 42.76%. The dissolution of manganese during leaching was negligible.IntroductionManganese and its compounds are widely used in the iron and steel industry as deoxidation and desulfurization agents and as alloying additives [1-2]. Because of the increase in demand, low grade refractory manganese ores are becoming a new source. Many Chinese manganese ores are high in phosphorus, which cannot be used directly for metallurgical purposes. This occurs because phosphorus enters into the metal phase during smelting and its presence sharply deteriorates the mechanical properties of the metal [3-4].Kanungo and Sant [3] investigated the dephosphorization of phosphorus-rich manganese ores by selective leaching with dilute hydrochloric acid. They observed that leaching with dilute hydrochloric acid (0.1-0.6M) could reduce the phosphorus contents to the specified limit of 0.12%. Ye [5] investigated dephosphorization of high-phosphorus manganese ore of the Huayuan type. Using high intensity magnetic separation, roasting and leaching with acid for dephosphorization, as used in the industry, a 40.15% manganese concentrate with a P/Mn ratio of 0.0037 was obtained. Yimin [6] investigated magnetic separation followed by inverse flotation of high-phosphorus manganese ore, and found that the P/Mn ratio could be reduced from 0.046 to 0.002."

Jan 1, 2012

By Marcelo Jimenez Bustos

The Chagres Smelter was the first in Chile to follow environmental regulations to control sulfur dioxide emissions. Because of this, the operation and development plans have had to incorporate environmental planning as part of its policies for almost three decades. The present article shows the development of the environmental standards applied to its operations, investments and operational improvements carried out to meet the regulations and improve competitiveness. Results to-date and future plans are outlined, as well as their impact on operations and the environment.

Jan 1, 1993

By Ryokichi Shimpo

Much amount of sludge is produced from the wastewater treatments in surface finishing industry. There are many problems for the abandonment of the sludge because of the high water content and heavy metals included. It is often observed that hexavalent chromium, which is toxic, is generated in the course of heat treatments of the sludge for reducing its amount by dispersing water. In this study, conditions of the sludge calcinations for reducing water contents have been examined. Maximum hexavalent chromium generation was observed in the temperature range around 773 K, at which most of the crystallization water decomposed from the sludge. When the heating temperature became higher than 1173 K, the amount of the hexavalent chromium extracted from the calcined sludge became as low as 10 mg/kg sludge. When the sludge was heated with iron oxides, FeO or Fe203, iron ferrite has been synthesized which may be used as a magnetic material. The amounts of hexavalent chromium generated in the heat treatment with iron oxides were not much different from those without iron oxides.

Jan 1, 2003