Search Documents

By M. A. Rabah, F. E. Farghaly, M. A. Motaleb

"Wastewater from industrial galvanization industry was reclaimed under current flow stream conditions. Results showed that the raw water contains 0.7 % by weight total suspended solids (TSS) causing turbidity amounting to 30. Measurements of Zeta potential as a function of pH revealed that solid separation takes place at pH 9. Addition of H2O2 to the polmer solution helps to oxdize ions of iron and zinc metals toinsoluble ferric oxide and zinc hydroxide to a higher state of oxidation. Addition of 5 mg/L of cationic magna flocculants polymeric solution helps the rapid separation of the turbidity. Separation of floccules so formed takes place by filtration. Addition of peroxide ions to the turbid wastewater confirms the physical stability of the flocs so formed. Impurity flocculation takes place in few seconds. Maximum temperature for safe solid removal was <30°C. The treated water was pure and safe for recycling or use in domestic purposes.IntroductionStocks and et. al. [1] show that the galvanizing process introduces spent pickling acid waste production, but its major constituent, could be used. Survey of the operational procedures adopted and the acid wastes produced by UK Galvanizers are reported. Various methods to recovery spent acid of suitable composition and to eliminate zinc contamination was considered. Application of the Kleingarn acid management system reduces waste volume, saves hydrochloric acid (HCl) and increases component throughput whilst, in conjunction with zinc elimination, could allow recycling of the majority of galvanizer’s acid wastes.Dahab [2]; Kerney [3] reported recycling of galvanizing products, including pickleliquor. Kerney suggested a mobile treatment plant for recycling pickling acids. Dahab found that pollution reduction could be achieved by relatively simple operational changes to the process that gave fairly short payback times.Rozenblat and et. al.[4] studied the extraction of zinc (II), iron(III) and iron(II) with Tributyl phosphate (TBP) from hydrochloric acid solutions containing high zinc(II) concentration. Two technological approaches for the separation are considered. Firstly, the selective extraction of iron(III) (iron(II) is oxidized to iron(III)) over zinc(II) with TBP deficiency. Secondly, iron(III) reduction to iron(II) followed by zinc(II) selective extraction with an excess of TBP. Prior stripping, the organic phase was washed with small amounts of water. Scrubbing of TBP solutions containing iron(III) contaminated with zinc(II) gives always a mixture of zinc(II) and iron(III) which must be recycled to the extraction step in continuous process. The following technological concept is proposed: reduction of iron(III) to iron(II), extraction of zinc(II) with 5-10 volume excess of TBP, washing of TBP phase contaminated with iron(II) with small volumes of water and recycling of the scrubbings and stripping of zinc with water."

Jan 1, 2008

By Farouk Tedjar

The growth of miniaturization in one hand and energy density need lead to rapid development of new chemistry for batteries as observed during last decade particularly in secondary systems. However dark side of the progress is always in environment impact and scarcity of resources. In the lithium segment a jump from six electrochemical series (all non rechargeable systems) before 1990 to more than 15 systems including new rechargeable systems has been observe during last decade. Lithium battery chemistry was enriched with new electrolytes, conductive salts and new oxide composition. In the same time, lithium ion battery safety was strongly improved during last period. The progress of these technologies was strongly boosted by the substantial growth of the mobile telephone market in the mid 1990&apos;s (+ 1% a month in 2000, and a 71% penetration rate in Europe in 2005 compared to just a few percent in 1996). This market is constantly in search of higher electrochemical performance (mainly energy density in front of increasing miniaturization. Recycling of end of life product could be managed not only in environment aspect, but also under resource conservation and economic aspect of arising technology (mainly on the effect of re-injection recovered materials) The Li-ion segment is a new branch in the cobalt market and impact of LiCoOx will be fitted with the actual increase of the demand for this battery. For this reason all the processes aim to valorize active and packaging material. RECUPYL process project was conducted in this direction to offer a new solution for recycling those lithium systems. The process has been developed at pilot industrial scales using synergy between new equipment (for mechanical pre-treatment step) and existing line at RECUPYL facility (for chemical treatment) and should lead to high valorization rate with a minimum hazardous co-products. The process was also developed in order to be able to recover news cathode materials introduced in electrode like LiFEPO4, LiMxCoyO2 and new anode composition in substitution with former carbon anode.

Jan 1, 2006

By C. Lupi

Zinc chloride electrowinning presents difficulties in obtaining smooth, compact and dendrite free deposits with a high current efficiency due to the presence of undesirable metal ions. However, it is hard to define a level of impurities tolerable in zinc deposition, and despite a lot of research in this field, the reaction mechanisms of the undesired metal ions are still not clearly understood. In this study, the influence of Fe, Cd, Co, Ni and Cu additions were investigated, as well as their synergic effect on the zinc electrodeposition process from chloride electrolytes and on the obtained deposit morphology. The tests were all performed in presence of TBACl which reduces the harmful effect of such impurities on the zinc reduction.

Jan 1, 2003

By Jiang Feng, Zhang Libo, Peng Jinhui, Guo Zhanyong, Ju Shaohua, Lei Ting

The clean utilization of the residue containing chloride, CuCl residue, produced from zinc hydrometallurgy is very important for the recycle of valuable metals. And drying is the main process in recycling. In this study, response surface methodology was used to optimize operating conditions of the drying of CuCl residue in a convection oven and desirability function used as the methodology for the optimization. Optimization factors were air temperature (80–100°C), material thickness (10–25mm) and process time (80–120min) while investigated responses was final moisture content. The optimum conditions were found to be the temperature of 95.48°C with the material thickness of 13.47mm for the process time of 89.48 min. Under optimum conditions, the predicted moisture content of CuCl residue was 4.11% while the experimental date was 4.13%. The experimental value after process optimization was found to agree satisfactory with the predicted value. After drying, XRD was used to analyze the main phases of CuCl residue. The CuCl residue is made up of CuCl,Cu2O, ZnS and other compounds.

Jan 1, 2015

By Andre L. De Vegt

Hydrogen sulfide is an expensive chemical used in nickel, zinc and copper mining and metallurgical operations for selective recovery and concentration of metals, from leach water streams, acid plant blow down streams, refinery electrolyte bleeds and precious metal, plant bleeds. Hydrogen sulfide is either produced on site by catalytic reduction of elemental sulfur or transported to the site as liquefied hydrogen sulfide (H2S) or as a sodium sulfide solution (NaHS) Biologically produced hydrogen sulfide has economically very interesting, application possibilities in the mining and metallurgical industry. Converting sulfates from waste streams into usable hydrogen sulfide by biological reduction results in operational cost savings in existing lime treatment systems. H2S can be produced biologically for less-than $500/ton S. For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove sulfate and heavy metals. The hydrogen sulfide produced is used for recovery of metals,, mainly zinc, from the ground water stream. The system has been operating since May 1992 treating a flow of 5000 m3/d. At Kennecott&apos;s Bingham Canyon Utah copper mine, a pilot plant started operation in November 1995 to develop the process for selective recovery of copper from leach water using biologically produced hydrogen sulfide from sulfate containing groundwater. Other pilot plants are operated at DOE&apos;s Pittsburgh Research Center and at Cominco Research focusing on selective recovery of metals.

Jan 1, 1998

By C. L. Lin

Transformation of linear grade distribution to volumetric grade distribution has been used to estimate the actual mineral liberation during wet, batch, ball mill grinding of a copper ore. The degree of liberation based on the multicomponent-multisize grinding liberation model using volumetric grade is lower than the apparent degree of liberation estimated from using King&apos;s linear intercept model.

Jan 1, 1987

By Jeffrey Shepherd, Scott R. Smith, Eduard Guerra

"Electrochemical and spectroscopic evidence for the dissolution of a Au electrode by meso-2,3- dimercaptosuccinic acid (DMSA) from an acidic LiCl04 electrolyte is presented. Near the potential of zero charge, DMSA was determined to form a stable layer on the metal surface but at more anodic polarizations, DMSA was displaced from the metal through an oxidative process. The anodic displacement of the layer from the electrode resulted in a small amount of Au that was detected in the electrolyte using atomic absorption analysis. The extent of Au dissolution, was monitored while holding the potential of the electrode for 24 hours at the thermodynamic Eo/H,O in LiCl04 electrolytes containing 10 mM DMSA. This routine resulted in detectable quantities of a soluble Au-DMSA complex in the electrolyte and the greatest leaching was observed at a pH = 2.0. At room temperature, the leaching rate was stable at 10.9 µg cm·2 hr·' however, upon increasing the temperature to 50.0°C, the rate of Au dissolution increased yielding an average rate of extraction of 40.1 µg cm·2 hr- 1. Interestingly, after the first 12 hours of leaching at 50.0°C, the leaching current decreased dramatically suggesting surface passivation which prevented further Au extraction. The implications of this process in the industrial leaching of Au will be discussed.IntroductionThe use of cyanide in the industrial process of leaching Au from ores has raised concerns regarding both operational safety and environmental issues surrounding the disposal of spent leaching eftluents in tailings ponds. Depending on the chemical nature of the processed ore, the spent solutions that are released into the tailings ponds can contain toxic cyanide, either dissolved or complexed with different metals and may pose serious risk to wildlife as well as freshwater contamination to nearby water systems. Because of these issues, some recent studies have focused on the exploration of more environmentally-friendly molecules to selectively leach Au with appropriate kinetics. However, to effectively leach Au into an aqueous solution, a suitable ligand that reacts to form a stable chemical bond with Au is needed to form soluble Au complexes that can be later recovered [I]. Recently several sulfur bearing alternatives have been shown to leach significant quantities of Au in aqueous solutions. These include thiourea [2], thiocyanate [3], and thiosulphate [4]. However, alkylthiols are also known to quickly form a stable covalent Au-S bond [5], but have been relatively understudied in term of their ability to leach Au in solution, even though some short chain thiols are water soluble and relatively nontoxic."

Jan 1, 2012

By Bora Derin, Sertac Yazici, M. Seref Sonmez

"In this study, the recycling conditions of waste liquor obtained after the production of tungsten boride powder from calcium tungstate by self-propagating high temperature synthesis (SHS) and the following hydrochloric acid leaching were investigated in detail. Environmentally unfriendly and extremely acidic (pH~ -0.3) liquor consisting of calcium, magnesium, and boron ions was treated with 1 M sodium carbonate solution to precipitate magnesium carbonate and calcium carbonate phases. The obtained amorphous precipitates were heated up to the temperature of 400°C for re-crystallization. As a result, MgO, CaC03 and CaMg(C03)z phases were obtained, while sodium, boron, chlorine ions were remain in the solution. The present study is still in progress.IntroductionSelf-propagating high temperature synthesis (SHS) is one of the techniques used in the production of a variety of advanced ceramics, inter-metallic, organic and inorganic compounds, oxygen free single crystals, and polymers [ 1, 2]. The reaction becomes selfsustaining and propagates in the reactant mixture, after initiation in SHS process. SHS products may contain the mixture of several unwanted compounds and elements. Therefore following acidic leaching process may be needed to purify the target product. In the previous study, calcium tungstate (Ca W04), magnesium (Mg) and boric acid (B20 3) mixture were reacted to produce tungsten boride powder by SHS process according to the Reaction 1. Then, magnesium and calcium containing byproducts (i.e. MgO, Mg3B206 and Ca3B206) found in the SHS product were leached out by using concentrated hydrochloric acid (HCl) solution to obtain pure tungsten boride powder [3].Ca W04 + 0.5B203 + 4.5Mg = WB + 4.5Mg0 + Cao (1)After the leaching, filtrate solution consisting of different amounts of magnesium, calcium, and boron requires additional treatment for the environmentally acceptable disposal.Several works were carried out about magnesium precipitation conditions and kinetics from brines. Rabadzhieva et al. investigated the precipitation of Mg(OH)z from brines by using NaOH as well as caustic soda [ 4]. Turek ve Gnot investigated the precipitation efficiency of Mg(OH)z for the temperature range between 10-40°C, while the reaction was kinetically experimented by Alamdiri et al [5, 6]. Homogeneous precipitation of nesquehonite (MgC03.3H20) by the reaction of MgCli with (NH4)2C03 in supersaturated solutions and factors that influence the precipitation of MgC03.3H20, such as reaction temperature, initial concentration, stirring speed, titration speed, equilibration time, have been studied by Wang et al [7]. The precipitation of Mg(OH)z by calcium hydroxide from aqueous solutions was studied by Baird et al. [8]. Stratful et al. focused on conditions influencing the precipitation of magnesium ammonium phosphate from wastewaters [9]. 1031"

Jan 1, 2011

By M. Nilmani, H. Pham

"A mathematical model was developed for the dissolution of particles in gas-stirred liquid baths, linking the hydrodynamic flow field of the bath, the average particle trajectory and liquid-side mass transfer controlled dissolution kinetics. The model was validated by comparison with experimental data for the dissolution rates of urea particles in gas-stirred aqueous CaCl2 solutions measured during this study. The dissolution rates of urea. particles were measured using an image analysis system.The effects of operating conditions on the dissolution rates of urea particles were investigated. It was found that the key operating parameters influencing the utilisation efficiency of particles were the gas flowrate, particle diameter and lance submergence. An optimisation of the operating conditions for the model urea-aqueous CaCl2 system indicated that the utilisation efficiency increased with decreasing gas flowrate and decreasing particle size for a given lance submergence.IntroductionThe utilisation solid reagents in molten baths varies from one process to another, depending upon the rates and mechanisms of the reactions between the particles and melts, as well as the trajectory and residence time of the particles in the melts. Previous studies have not attempted to predict the utilisation efficiency of injected solids by coupling the motion of the particle with its dissolution rate. Instead, the particles have usually been assumed to remain suspended in the bath until completely dissolved, and the mass transfer coefficients were based on the average specific mechanical energy dissipation rates in the bath. Investigations of this nature relevant to the present study have been undertaken by Apelian et al. [1], Brucato et al. [2] and Langberg and Nilmani[3]. The objective of the present study was to develop a mathematical model, incorporating both the reaction kinetics between the particles and liquid and the particle motion simultaneously, to predict the dissolution rates and times of the particles. The mathematical model was validated by comparison with experimental dissolution rates of a cold model analogue system measured using an image analysis technique, and then applied to optimise the operating conditions in the model system."

Jan 1, 1996

Sm-Co alloy is a kind of magnetic material with high power and has been applied in modern industry widely. In this study, the wet chemical co-precipitation was developed for synthesis of the Sm-Co alloy oxide precursor. The thermodynamic analysis of the studied system was done to clarify the solution behavior theoretically based on the thermodynamic equilibrium and simultaneous equilibrium. Then, the experiments were done to address the various effects on the wet chemical process, including solution pH, reactant concentration, dispersant, reaction temperature and time, etc. It is found that by precise control of the process, the Sm-Co alloy oxide precursor was synthesized with fine crystallization and special size & size distribution.

Jan 1, 2005

By Sasa Djokic

In developed countries, the difference between demanded and produced quantities of non-ferrous and rare metals are compensated by secondary raw materials recycling and reprocessing of by-products from both ferrous and non-ferrous extractive metallurgy. Utilization of non-ferrous and rare metals from the metallic secondary raw materials is very significant, both for recovery of the metal value and contribution to the environment protection. Similar to all non-developed countries, the extractive metallurgy in Serbia was based on available natural resources and not so strict environment protection regulations, which was either insufficient or completely absent. Today, Serbia is at the beginning of development of efficient and economical technical and technological solutions in order to ?ecologize? technogenic systems by waste materials, secondary raw materials and degraded soils regeneration (by recycling and revitalization). Several metallurgical technogenic systems in Serbia, together with secondary raw materials classification according to their potentiality for metal extraction by using the existing technologies and expected economical and ecological effects of recycling, are discussed in this paper.

Jan 1, 2005

By Zenjiro Asaki

The copper concentrate particles dissolve quickly into the molten matte in the smelting furnace of Mitsubishi Process, which indicates that the sulfide smelting is essentially a gas/liquid reaction. In this paper, theoretical calculation has been made on the rate of oxidation of FeS component in the matte to form FeO by rising gas bubbles using the penetration theory. The results showed that all the oxygen in the bubble of 1.2 cm in diameter, which is the maximum stable diameter, is consumed in 3 ms. This time required is sufficiently short, and it results in the actual operation of smelting furnace of 1100% oxygen-efficiency. These calculations indicate that most smelting reactions are completed just under the lance, except slag formation.

Jan 1, 2002

By Zhongming Ren

"A new process of near net shape continuous casting of metal pipe has been put out. The specialty of the process is that no inner core is used. The principle of the process has been presented, and the effect of several factors on the thickness of the pipe has been investigated experimentally and numerically. It is shown that the temperature and the level of the molten metal, cooling intensity of the mold, and the velocity of casting influenced the thickness of the pipe apparently. In order to improve evenness of the thickness of the pipe, the mold was dedicatedly designed, and special methods were taken. By this process, a metallic material like ""bamboo"" was fabricated.IntroductionMetal pipe is a widely used material. Up to now, many processes have been put out to produce the pipe. However, the processes are usually expensive and inefficient. For instance, the welding pipe, which is most widely used, is produced through continuous casting of slab, rolling of the slab into sheet, and welding, with several times of heating and processing. Continuous casting of pipe can not produce small diameter of pipe, which is mostly needed, due to the inner core. Even though. OCC process is novel in fabricating the pipe with small diameter, it is inefficient. In this paper, the no-inner core continuous casting of pipe was proposed. With this process, pipe with small diameter can be produced efficiently. The influence of several parameters on the thickness and evenness of piper wall. With this process, a ""bamboolike"" pipe was fabricated.ExperimentThe experimental apparatus is shown in Fig. I. It is composed of mold, furnace, melt level adjuster, and dummy pipe. In the process, the level of the melt was adjusted at a proper position, then the mold along with the dummy pipe was inserted into the melt in a certain depth. The melt in the mold began solidifying, forming a solid shell. After that, the dummy pipe was pulled upward in a certain speed, drawing the solid shell out of the mold. Thus, a pipe was continuously cast."

Jan 1, 2000

By N. Kanari

Reactivity of MgO towards C12+air, C12+N2 and C12+CO gas mixtures was studied up to 1000 °C. Carbochlorination of MgO occurs at temperatures lower than that of its oxychlorination. Effects of gas flow rate, temperature and partial pressure of the carbochlorinating gas mixture on the reaction rate were investigated. The apparent activation energy of MgO carbochlorination is 49 kJ1 mol between 425°C and 600°C. At 550 °C, the apparent reaction orders with respect to C12+CO, C12 and CO, are 2.37, 1.47 and 0.89, respectively. At this temperature, the maximum reaction rate was obtained using a C12+CO gas mixture having a Cl2lCO molar ratio equal to about 0.6.

Jan 1, 1998

By A. V. Tarasov, V. M. Paretsky

"A mathematical model of the low-temperature (soft) nickel oxide reduction (SNOR) in a tubular kiln has been developed including an equation describing changes in the nickel oxide content of the solid material along the length of the kiln; an equation describing the changes in the content of reagents ensuring nickel reduction (i.e., hydrogen and carbon monoxide) in the gas phase along the kiln length; as well as the temperature along the kiln length. The kinetic relationships used for the development of the model had been determined based on experiments conducted specially for this purpose. Model investigations were conducted to determine the distribution of such parameters along the length of the kiln as the contents of metals oxides in the solids, partial pressure of hydrogen and carbon monoxide, variations of the temperature depending on the SNOR process conditions, including the kiln rotation speed. Based on the data obtained, a simplified regression model of the reducing roasting process was developed.IntroductionAt the SeveroNickel complex (Russia) a technology has been developed and is being introduced on a commercial scale for low-temperature (soft) nickel oxide reduction (SNOR) in tubular kilns.The SNOR process has a number of advantages, the main of which are the higher degree of metallization and higher chemical activity of reduced nickel oxide attributable to the lower fusion of the surface of the grains of reduced material due to lower process temperature (800-1000°C) and improved reducing ability of the gaseous phase. However, the fact that the process is conducted in a gaseous phase sets higher requirements to the consistency of its composition necessitating careful continuous monitoring and control of the main process parameters."

Jan 1, 2001

By Tsisana Gagnidze

A processing of technogenous wastes, which involve a gold-containing sulphide minerals, is a potential source to supplement the gold reserves. Hence, searching of ecologically safe and economically reasonable methods for processing of gold-containing technogenous wastes is a topical problem. To increase a parameters of gold extraction and to simplify a technology of the processing of above-mentioned wastes of sulphide minerals, an investigations have been carried out in the direction of the use of the method of electrochemical leaching without any preliminary processing of the mineral. It was established experimentally that an introduction of nitrogen containing organic additive into chloride solution favours to reduce a Red/Ox potential of the solution from 0,8÷1,2 V to 0,35÷0,5V, which permits to conduct the process of direct electrochemical leaching at ?soft? oxidation regimes at temperatures 20-300C C without an environmental contamination by molecular chlorine and with a high degree of a gold extraction up to 80-90%.

Jan 1, 2008

By Akira Yazawa

In the field of pyrometallurgy, the equilibrium evaluation has recently become easy by use of thermodynamic software, but it is strongly desired to estimate the amounts of non-equilibrium minor components to simulate practical processes. However, simple physico-chemical technique can not be applied to evaluate practical non-equilibrium components for many reasons. As an engineering solution for postulated equilibrium system, the activity coefficient is modified and introduced as the simulation parameter referred to as the "adjustment coefficient." This modified thermodynamic calculations were adopted to various sulfide roasting processes where many solid phases are participating and the system is not necessarily in equilibrium. Successful simulation was realized by assigning suitable adjustment coefficients for minor components which form a pseudo solid solution in the calcine. Some examples from sulfation roasting and dearsenizing roasting were discussed. In the smelting system, the loss of copper in slag is caused by equilibrium and non- equilibrium reasons, that is, chemical dissolution and entrainment of copper in slag. The total copper content of slag was simulated by use of the adjustment coefficient for entrained copper.

Jan 1, 1998

By Jenq-Gong Duh, Jyh-Wei Lee

"Hard chromizing process is a method for developing a surface modified coating providing wear, corrosion resistance and high temperature surface protection. Two carbon steels with 0.45 wt% and 0.95 wt% carbon contents, respectively, were chromized with pack cementation process at 950'C for 4 and 9 hours, respectively. The phase transformation and microstructure phenomena of chromized coating layer and matrix of two steels were studied with X-ray diffractometer and electron probe microanalyzer. (Cr,Fe)23C6 and (Cr,Fe)7C3 carbides and (Cr,Fe)2N1-x nitride phases were observed on the chromized surfaces. The thickness of chromized layers obeyed the parabolic rate law. The mechanism and diffusional kinetics of the chromizing process were proposed. The diffusivity of chromium in the (Cr,Fe)7C3 carbide phase was calculated using the moving boundary method.IntroductionChromizing process is one of the surface treatment technologies that can produce a chromium contained surface layer with sufficient corrosion and wear resistance on the steel matrix [1-7]. The relatively low cost and no ""line-of-sight"" restrictions are main advantages of chromizing. Adequate bonding strength of these coatings to the substrate was reported [7]. Chromizing process can be classified into soft chromizing and hard chromizing [2]. Soft chromizing is applied to steels containing less than 0.1wt% carbon through which chromium will be diffused. High temperature oxidation resistance improvement is the main purpose of soft chromizing process. On the contrary, the hard chromizing can be applied to steel containing more than 0.3wt% carbon, and very hard chromium nitride and carbide layers will be formed on the surface, which are very resistant to wear, corrosion and temperature [5-7]. In the previous studies on the Fe-Mn-Al-Cr alloy [5,7] and carbon steels [6], the thickness (X) of chromizing layers was analyzed and found the parabolic rate Jaw prevailed:"

Jan 1, 2004

By V. M. Lsoitko

Statistical methods of technological mineralogy are used to model processing flowsheets in order to improve ore dressing efficiencies. The procedure involves determining geological and mineralogical characteristics of ores, classifying ore types and metallurgical procedures, and developing computer programs to interpret essential mineralogical parameters from on-stream analysis data. The on-stream analysis data include magnetism, radioactivity, luminescence and assays. The data are interpreted by computer and appropriate adjustments are made automatically in the plant.

Jan 1, 1989

By F. Leclerc, V. Rebeyrolle, M. Revil-Baudard, A. Jardy, M. Založnik, H. Combeau

"Since the quality of Vacuum Arc Remelted ingots is linked to their chemical homogeneity and metallurgical structure, a modeling study of the solidification during VAR has been undertaken. It is based on the solution of the coupled transient heat, momentum and solute transport equations during the remelting of a cylindrical ingot. Solidification mechanisms implemented in the model include a full coupling between energy and solute transport in the mushy zone, and accounting for nucleation and finite diffusion of solutes at the microscopic scale, in both solid and liquid phases. This modeling can be applied to actual multi-component alloys. In this paper, the macrosegregation in Zircaloy 4 ingots is investigated. To validate the model, one single melt of a homogeneous electrode has been specifically performed. The comparison between the predicted macrosegregation and the experimental results shows the importance of accounting for solutal convection to forecast properly the macrosegregation in remelted ingots.IntroductionVacuum Arc Remelting of zirconium alloy ingots is a key step in the manufacturing process of fuel assembly components in nuclear reactors. The control of the chemical homogeneity is indeed fundamental to ensure the quality and the in-reactor performance of the final products. Despite the use of electromagnetic stirring to homogenize the liquid melt composition, chemical heterogeneities develop in the mushy zone during the solidification stage. One of the main challenges for zirconium producers, as well as titanium producers, is to master the VAR process in order to control the macrosegregation in remelted ingots. Macrosegregation results from the association of microsegregation and transport phenomena. The latter are primarily due to the flow in the liquid and mushy parts. It is now well established [1-4] that the hydrodynamics of the melt pool in a VAR ingot depends on the combined action of the followings: thermal and solutal buoyancy, self-induced electromagnetic force and the periodic centrifugal force caused by the angular movement generated by the stirring. However, for zirconium alloy ingots, the effects of thermal and solutal buoyancy forces on macrosegregation through their influence on the flow in the mushy zone have not been clearly identified."

Jan 1, 2012