Search Documents

By Kazuyuki Kakegawa

"Sintered body of lead zirconate titanate (PZT) was prepared through the spark plasma sintering (SPS) technique. When the mixture of raw materials was calcined at 800°C and sintered at 900°C for 10 min. with SPS technique, the sintered body had almost theoretical density but was a mixture of lead titanate (PT) and PZT. When a calcining temperature of 1100°C was employed, sintered body had a single PZT phase but a lower density. High dielectric constant was obtained for a sample calcined at 800°C, sintered with SPS tecbriique and fired again in the air at 1100°C.IntroductionSpark plasma sintering (SPS) is a recently developed technique for sintering metals and ceramics1. The scheme of SPS is shown in Fig. 1. Sample is put in a graphite die in a vacuum chamber. It is pressed and pulse voltage is applied. The electric current heats the die. It is said that the pulse causes a spark-plasma between particles in the sample. Because of the spark- plasma, sample can be sintered at temperatures lower than that in the ordinary sintering by several hundred degrees of Celsius. The sintering period is also very short2Low sintering temperature and short sintering period in SPS technique cause low reaction rate. It is both disadvantage and advantage. In some cases, the reaction cannot be completed under the SPS conditions. If a mixture of several compositions having different properties can be sintered without a compositional change by the diffusion during the sintering, combination of properties, and therefore a design of property will be possible3. The low reaction rate of SPS may enable such combination."

Jan 1, 2000

By Maria Kuttig, Christian Ruback, Gerhard Tober, Petra Maier

"It has been demonstrated that there is a strong relationship between work hardening with various post heat treatment and cyclic deformation behavior of structural steel S275. This study contributes to a project developing a process for the complex forming of steel, which combines rolling and bending. Due to the complex geometry of the final work piece, the deformation degree varies greatly. The forming temperature, as well as post heat treatruent, influences recrystallization processes in dependence of the local deformation degree, resulting in inhomogeneous microstructure of the work piece, which affects the quasi-static and dynamic properties. Cyclic creep and hardening or softening has been monitored during constant amplitude loading at stresses near fatigue strength in normalized condition. Work hardening, stress relief or recrystallization influence the cyclic deformation behavior and produces cyclic creep effects. Cyclic softening or hardening and creep were observed to occur in parallel. To what extent these properties are noted depends on the deformation degree.IntroductionThis work is part of a research project developing a new process for the three dimensional forming of steel. For the final product the fatigue strength influenced by the forming parameters is very important. Due to its complex geometry, the formed final plate has different deformation degrees. This leads to different recrystallization behavior and heat treatruent will have different effects on the microstructure. The peak deformation degree cp of the plate will be around -0.5 what leads to the analysis using rolling from 22 mm to 13 mm of thickness. The quasi-static material properties are very important for calculating the preliminary design. However, work pieces which are cyclic loaded need fatigue tests to describe the in-service material behavior. [l] For the prediction and to guarantee the wanted life-time of the part cyclic deformation tests are important. [2, p.23-32] When it is assumed that the work piece will only loaded in cyclic tension, fatigue testing will be done from zero to a maximum force value. In preliminary tests this value is the tensile fatigue strength from a Smith diagram. During processing, here forming, work hardening takes place resulting in strengthening. Therefore, in further tests maximum load can be increased to monitor cyclic deformation mechanism in more detail. However, to study cyclic creep and hardening and softening data should be evaluate over sufficient life time and should not fracture too soon."

Jan 1, 2013

By James C. Barker

Near Rainbow Mountain in the east-central Alaska Range an ultramafic complex forms a sill-like intrusion composed of dismembered bodies exposed along the south side of the Denali Fault and Broxson Gulch Thrust. The complex comprises dunite and peridotite with lesser gabbro, which together exhibit poorly defined, steeply-dipping compositional layering. The complex hosts four types of copper-nickel occurrences which have characteristic platinum-group elements (PGE), gold, and cobalt distributions. Three of the occurrence-types are considered to have formed as a result of primary mineral segregations which developed during intrusion of the complex. The fourth type of copper-nickel occurrence formed as a result of post-magmatic hydrothermal fluids at intrusive contacts. Scanning electron microscope examination indicates that PGE occur as micron-size telluride and arsenide minerals.

Jan 1, 1987

The oxidation of ferrous ions by oxygen in sulphate solutions is a very slow process, but it tills long been known that the addition of sulphur dioxide increases the rate of reaction very significantly. The kinetics and mechanism of the process were investigated in the laboratory and the results confirmed the advantage of adding small amounts of sulphur dioxide to the oxygen stream for the removal of iron from solutions. The effect of various parameters on the overall rate of iron oxidation and precipitation was studied. In particular, temperature, acidity and composition of the gas mixture were considered and the optimum conditions for the precipitation of goethite were determined.

Jan 1, 1991

By Peter Forschner

Classical Mixing Theory is based on applying many fundamental correlations to standard baffled dished bottomed vertical cylindrical vessels with high degrees of symmetry. Horizontal autoclaves operating at elevated temperatures and pressures have been used for more than two decades. All compartments and especially the first and last compartments are asymmetrical. To date no comparison of the effects of the asymmetric geometry on mixing system design and scale-up has been published. The results of investigating solids suspension, mixing time, momentum transfer from the impeller to feed slurry and feed inlet location in the first autoclave compartment are presented as influences on residence time distribution. CFD modeling was developed and verified with the test apparatus.

Jan 1, 2003

By Justin Karl, Ali Gordon, James DeMarco, Yongho Sohn

"Aluminum metal-matrix composites are lightweight materials that have the potential to supplant steel in many applications. The current work helps to identify the parameters that confer maximal strength and ductility. Torsion tests were performed on the as-cast aluminum metal-matrix composite A359-SiCp-30% at a variety of temperatures and twist rates. Dependence of material properties on temperature and strain rate were identified from equivalent stress-strain curves constructed from the reduced data. Examination of the microstructure was performed on the as-cast material and on fracture surfaces. A temperature-and strain rate-dependent constitutive model was applied to simulation of the mechanical response of the torsion specimen. Trends in material properties corroborate and extend trends identified previously under tensile loading with regard to temperature and strain rate dependence. Shear properties of simulated specimens agree with properties obtained through experimentation.IntroductionAluminum metal-matrix composites (A1-MMCs) have become increasingly popu1ar in recent years. While unreinforced aluminum alloys have low densities and high ductilities, they are not suitable for many applications due to their lack of strength and stiffness. To provide added strength and stiffness while maintaining favorable densities, it has become common to reinforce aluminum alloys with silicon carbide in various forms, although usually the inclusions are in the form of whiskers or particles. The result is a composite material with superior specific strength and stiffness. While whisker-reinforced composites are expensive due to the necessity of processing by nonstandard techniques and have low transverse properties when rolled, particle reinforced Al-MMCs have transverse material property values almost as high as the longitudinal properties and are not as expensive to process as whisker-reinforced Al-MMCs [1]."

Jan 1, 2012

By Sung-Joo Lee, Gi-Chon Han, Nam-Il Um, Hee-Chan Cho

"In Korea, almost all of bottom ash produced by coal power plants is disposed of in ash ponds. Ash storage areas comprise more than 80% of most coal power plant sites. This disposal method is causing environmental problems and a managerial burden for plant operators. In this study, investigations to develop a beneficiation process for separating coal pond ash into various products were undertaken. To improve efficiency of the separation, coal ash was separated by sizes and each size fraction was subject to various beneficiation processes. The separation process used were flotation (-200 mesh size), hindered settling (16x200) and tabling (16x200 and 8x16 mesh). The results showed that various marketable products, such as lightweight aggregate, sand, high-carbon fuel, could be recovered from coal pond ash using simple physical separation techniques.IntroductionDue to the increased use of coals every year, about fifty million ton of coals were used in 2007 alone. As a result, about 6 million tons of coal ash were generated. In Korea, the coal bottom ash is classified as a general industrial waste and is usually disposed of in ash ponds. The costs for this disposal method continue to increase due to rising costs of site management and development and more strict environmental regulation. Therefore, utilities are constantly looking for ways to increase utilization of coal ash. In this study, various beneficiation processes were evaluated to examine the possibility of separating coal pond ash into various products which can be used as aggregates and high-carbon fuel."

Jan 1, 2008

By Tracy T. Morris, Luis G. Navaro

"Anodic copper slimes produced during the electrolytic refining of copper are routinely batch leached to remove copper. At the Amarillo Copper Refinery, an atmospheric leaching process was converted to an autoclave pressure leaching system to improve the removal of copper, reduce the consumption of oxygen, improve leaching times and enhance tellurium recovery. The benefits of pressurized versus atmospheric leaching of slimes were soon realized by obtaining the desired level of decopperization in a shorter time and with lesser quantities of reagents. The autoclave was designed and constructed with a unique oxygen injection system that enables good control of the leaching process and with no plug-ups. Other features include a mass measuring system that balances the quantity of slimes to be leached to the desired final solution concentration based on initial feed concentrations. The end result was a more efficient and controllable leaching process for removing copper from anode slimes.IntroductionThe electrolytic refining of copper consists of an electrolytic cell filled with a sulfiiric acid based electrolyte and pairs of copper anodes and cathodes. When a current is applied, copper in the anode dissolves and is plated onto the cathode. Impurities within the anode that are more noble than copper do not dissolve and end up at the bottom of the cell and are referred to as slimes. Gold and silver are the main slimes constituents of interest because of their monetary value, but there typically are significant quantities of selenium, tellurium, lead, antimony, arsenic, bismuth, nickel, silica and tin. Copper is also present, usually as a metallic or as a reactant with tellurium, selenium, oxygen or sulfur and can range from 10 to 30% of the slimes fall."

Jan 1, 2012

By Zan Yao, Sha Lv, Geoff Wang, Baojun Zhao, Zongze Huang, Jin Zou, Xiaodong Ma, Zhouhua Jiang

55SiCr steel is one of the important spring steels widely used in automobile manufacturing. The presence of micro inclusions in the steel can significantly influence a number of spring properties such as fatigue strength. It is important to understand the mechanism of the inclusion formation so that size and proportion of the inclusions can be controlled. Inclusions in Si-killed 55SiCr spring steel have been analysed by scanning electronic microscopy and electron probe X-ray microanalysis. The chemistry of the inclusions observed in 55SiCr steels can be represented by the SiO2–Al2O3–CaO–MgO system. It was found that the compositions of the inclusions cover a wide composition range, which indicates that these inclusions were formed from different reactions. The possible mechanisms of the inclusion formation are discussed. It would be possible to characterize and manage the inclusions in the spring steels deoxidized by Si.

Mar 1, 2017

By Brian Patrick, Norman Bell, Mark Schoenfield, Thomas Weber, Dietrich Gross

"The reduction of carbon dioxide emissions and the resultant greenhouse gas affect is hampered by the fact that all fossil fuels contain copious quantities of carbon. Process tweaking can keep the amount of carbon dioxide to a minimum but cannot significantly reduce the amount of carbon dioxide generated. The very nature of utilizing fuels requires that they be burned to release the heat required for the various processes. Reduction of metal oxides to manufacture or modify pure metals, generation of power, transportation and many other forms of fuel usage result in much of the generation of man made carbon dioxide. Oxyfuel is a unique contributor to carbon dioxide emissions. While creating higher concentrations of carbon dioxide the total volume of carbon dioxide generated is reduced. This paper will examine the unique characteristics and potential of oxyfuel that make the generation of lower volumes of carbon dioxide possible.Nearly ten years ago a commercial application of oxy-fuel was installed at Jupiter Aluminum Company in Hammond, Indiana. This process was funded and developed by Dietrich Gross CEO. This aluminum remelt facility now runs completely on oxy-fuel and has continuously for over ten years. This has reduced the melt rates to as low as 750 BTU per pound in continuous melting periods."

Jan 1, 2009

By Helfried Nafe

"For about a century thermodynamically absurd facts have been propagated in conjunction with the iron-carbon phase diagram. These facts concern fundamental relationships of chemical thermodynamics. Attention is turned here to the discussion of only one of the relevant aspects of the subject, i.e. the definition of the thermodynamic activity of the solute and its implications for the iron-carbon solution.IntroductionThe view on the iron-carbon solution is characterized by the assumption that the solute may appear in two different forms, i.e. graphite and cementite. Accordingly, two carbon solubilities are differentiated, on the one hand for graphite and, on the other hand, for cementite. As a consequence, two versions of the phase diagram exist simultaneously, the application of which depends on the prevailing conditions, (i) the so-called stable phase diagram with graphite as solute and (ii) the metastable one that is based on the cementite-in-iron solution. These diagrams are joined together in the double phase diagram that originates from Heyn [l ], with the first ideas mainly going back to Stansfield [2] and Charpy [3].Thermodynamically, the most inadequate implication of the Fe-C double phase diagram is that the carbon activity may take values larger than unity. With the standard state of the activity being that of the pure substance, i.e. the Raoultian one, such a value implies the nonsensical existence ofa state purer than pure. The explanation of this physical state, ifthere is any, vaguely refers to supersaturation and, in the wider sense, to the physico-chemical phenomenon of metastability. Other aspects of chemical thermodynamics are likewise involved. Therefore, the comprehensive investigation into the present subject requires more topics to be considered than only one separate issue. Not only should the criticism of the present view be in the focus but also the discussion of new ideas capable of reconciling the experimental facts, known about the F e-C system, with the fundaments of chemical thermodynamics. All this, however, cannot be provided here because of the limited space available. As a consequence, in what follows only a part of the whole problem is under scrutiny, i.e. the definition of the thermodynamic activity and its role for the interpretation ofrelevant experimental facts."

Jan 1, 2014

By M. E. Ramos Rada

Mexicana de Cobre, which is part of Grupo Mexico, carried out studies for the construction of a copper refinery in the La Caridad Metallurgical Complex located in Nacozari, in the state of Sonora, Mexico. After the studies were concluded, the decision was made to construct a 180,000 t/y refinery using the state of the art permanent cathode Kidd Process. The basic engineering was developed by Fluor Daniel and the detail engineering and the construction were carried out in record time by the Mexican company Bufete Industrial. During the construction phase, Grupo Mexico decided to expand the refinery, and actions were taken to increase its capacity by an additional 120,000 t/y; the final result was a refinery capable of producing 300,000 tonnes of grade A cathode per year. Construction began in January 1996, and the operation of the first stage began on July 1, 1997. The operation of the second stage commenced on January 7, 1998. The capacity of the first stage was reached in November, 1997 and the total capacity of the refinery was achieved in May, 1998. This presentation describes the process and equipment installed in the refinery, the steps leading to the start-up, the operation and the results obtained during the first two years, the handling of anodes with high impurity contents, and the problems confronted and the way they have been solved. It also includes personnel productivity, the control parameters and the most relevant data on the operation of the process.

Jan 1, 1999

By Garry W. Warren

The brass foundry industry produces a significant amount of waste sand containing Cu, Zn and Pb which is often classified as a hazardous waste due to Pb content. The potential application of a hydrometallurgical process to treat the sand by extracting metal values and thus detoxifying the material has been investigated. The process involves leaching of metal values followed by cementation. The emphasis of this investigation was on the leaching step, although some preliminary cementation experiments have been performed. In order for any alternative treatment scheme to be successful, the smaller size fractions of the sand must be addressed. Experiments have been performed on five individual size fractions using various lixiviants HCI, acetic acid and HCI/NaCI. Cu extraction was found to be slower than either Zn or Pb. Results obtained in this investigation indicate that copper is present in two forms, an oxide form which dissolves rapidly and is insensitive to the level of oxygen, and a less soluble form, probably metallic which dissolves more slowly and requires an oxidizing agent. The presence or absence of oxygen had no influence on the rate of Zn dissolution indicating that zinc is present mostly in oxide form. Toxicity Characteristic Leaching Procedure (TCLP) tests showed that residues could be produced which meet the toxicity limit for lead. Preliminary cementation experiments have also demonstrated the feasibility of Cu and Pb recovery.

Jan 1, 1991

By Saeid Pournaderi, Ahmet Geveci, Ender Keskinkilic, Yavuz A. Topkaya

There are mainly three commercial nickel laterites in Turkey: Gordes, Caldag and Sivrihisar. The first two appear in Western Anatolia. The third one, Sivrihisar (Yunusemre) laterites have been found in the first decade of the millennium, in the Central Anatolia region of Turkey. Since then, mining facilities have been continued in Yunusemre. Calcination, prereduction and smelting of Sivrihisar laterites have been extensively studied and published. In the current work, some results of the studies related to characterization of Sivrihisar laterites will be presented.

Jan 1, 2016

By Mingchun Lu, Zhe Wang, Mingming Cao, Xiangdong Xing, Shan Ren, Jianliang Zhang, Zhengjian Liu

"The effect of reduction temperature on the vanadium titano-magnetite carbon composite pellets was investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM), and the discussion has put emphasis upon the enhanced reduction mechanism of additives containing CaF2 and NaF in this paper. The results showed that the reduction temperature of 1350°C was needed for the generation, mergence and growing up of metallic iron as well as monomer dissociation between metallic iron particles and slag phase in the vanadium titano-magnetite metallization pellets. The iron compound was completely reduced into metal iron, and Fe2Ti04 was mainly transformed into metal iron, (Fe,Mg)Ti205 and FeTi03 at 1350°C. The maximum metallization ratio was only 88.5% at 13500 for 30 min without any additive. However, with the addition of 3.0% CaF2 or NaF, the metallization degree of pellets could reach up to 94.8% and 92.5%, respectively.IntroductionVanadium titano-magnetite which is mainly distributed in the area of Panxi, Chengde and Maanshan in China is a kind of complex iron ore which contains various valuable metal elements such as iron, vanadium, titanium, etc. Among the above areas, Panzhihua (Sichuan Province in China) area possesses the largest deposits of vanadium titano-magnetite and the future reserves are more than 100x108t, and the reserves of Ti existing as Ti02 reach to 8.7x108t which occupy over 91% of the whole nation and ranked No.1 in the world[1]. Lots of researches on the comprehensive utilization of vanadium titano-magnetite have been conducted in the world. And many technological processes have been applied successfully in industrial production. Among these processes, the process of rotary kiln-electric furnace is employed to recover iron and vanadium in South-Africa, while the process of blast furnace-rotary furnace is widely used in Russia and China. Besides, many researchers have made efforts on employing new direct reduction process to realize the effective comprehensive utilization of vanadium titano-magnetite[2-4]. However, the direct reduction process is only researched in laboratory and it has not been used in industry."

Jan 1, 2013

By Christine Wenzl, Andreas Filzwieser, Stefan Konetschnik

"The METTOP-BRX-Technology is a novel manifold electrolyte inlet, which allows improved productivity and production in new and existing tankhouses by achieving higher current efficiency and cathode quality, as well as using current densities higher than 400 A/m2. Two installation examples are shown: Montanwerke Brixlegg AG, Brixlegg, Austria (upgrade of existing tankhouse) and Xiangguang Copper, Yanggu, China (new tank house). Montanwerke Brixlegg AG has been using the METTOP-BRX-Technology since 2005, and converted half of the whole tankhouse to METTOP-BRX in 2011 in order to use a current density of more than 400 A/m2. Xiangguang Copper started up their second tankhouse in May 2011. This tankhouse was constructed in the same way as the existing tankhouse, but was designed for 292,000 t/a cathode copper (existing tankhouse: 200,000 t/a) by using the METTOP-BRX-Technology. This production increase is a consequence of a much higher current density, namely 410 A/m2, compared to 280 A/m2 in the old tankhouse.IntroductionCopper electrorefining has been practised for more than hundred years, the last big change being the implementation of stainless steel cathodes in the 1980s [1], In 2005, the METTOP-BRXTechnology was first introduced. This technology was developed jointly by METTOP and Montanwerke Brixlegg, Austria, and allows improvements in productivity and production in new and existing tankhouses in an economic way. The METTOP-BRX-Technology is a novel manifold inlet that allows improved tankhouse productivity by increasing current density and/or current efficiency while maintaining or improving cathode quality [2]."

Jan 1, 2012

By G Hope, C Young, R. N. Gow

"The presence of enargite (Cu3AsS4) is problematic in gold processing as it is refractory, increasing cyanide and oxygen consumption, and enviromnentally hazardous. Selective leaching and treatment of the arsenic would prove advantageous to conventional gold leaching methods. The reactivity of enargite samples from Montana, US and Quiruvilca, Peru were studied under alkaline conditions, pH range of 8-13, using a cyclic voltammetry corrosion cell setup. Raman spectra of the surface were taken during and after cycling to compare surface species against theoretical predominance diagrams. Under slightly oxidizing conditions, covellite (CuS) peaks were found on the surface in a short matter of time, above - 200m V vs SHE for pH 9-13, suggesting arsenic leaching, but for longer conditioning times, elemental sulfur peaks were also found, which created a passivating surface layer. By operating above pH 12, under reducing conditions, ~-500mV vs SHE, arsenic can be leached as a thioarsenate (AsS4-xOx3-), without sulfur formation.IntroductionEnviromnental limitations on pyrometallurgical processing of arsenic has pushed the desire to process enargite-, Cu3AsS4, bearing concentrates towards a hydrometallurgical solution. Attempts to process can be broken down into two categories - the co-dissolution of arsenic and copper under acidic conditions or the selective leaching of arsenic under basic conditions. The selective leaching of arsenic would preferably leave behind a chalcocite, Cu2S, or covellite, CuS, phase that would be more amenable to conventional processing methods of the copper and gold industries. These methods employ bi- or poly-sulfides to leach arsenic as Assl· [1-4], hypochlorite leaching [5-7], ammoniacal leaching [8] or fine grinding to mechanically activate the enargite surface and increase normally slow reaction kinetics[9]. This study looked into the surface formations of an enargite electrode under alkaline conditions, in a pH range from 8-13, as it cycled from -1000 mV to 1000 mV vs SHE. The understanding of the formations and under what conditions they form will be helpful in further development of any of the aforementioned processes."

Jan 1, 2012

By H. H. Kellogg

The thermochemical properties of molten solutions in the binaries Cu-Bi, Cu-Sb and Bi-Sb, as well as the ternary Cu-Bi-Sb, have been correlated and described in mathematical form by use of the associated species concept combined with the three-suffix Margules equations to account for the non-idea 1 behavior of the solution species. Agreement of the correlations with experimental data is excellent (relative deviation of less than 2.5% in the values of the activity coefficients) in most cases. The correlations are applicable over the entire composition range of each system, and in the temperature range 700°-1250°C.

Jan 1, 1985

By Yun Guo, Min-Min Lin, Bing Xie, Hong-Yi Li

The extraction of vanadium from vanadium-containing APV-precipitated wastewater by W/O microemulsion system was studied. In the N263/n-heptane/isoamyl alcohol/NaCl microemulsion system, N263 played double functions of cationic surfactant and extractant to form microemulsion in n-heptane, and isoamyl alcohol was added in the microemulsion as a cosurfactant. The extraction of vanadium by W/O microemulsion systems effectively accelerated the extraction and improved the extractatability because of the enormous increase in the micro-interfacial surface area. Due to ion association with extractant, vanadium was extracted into the microemulsion phase. The influence of different parameters on the extraction ratio (E%) were investigated, including the volume ratio of aqueous phase to microemulsion, surfactant concentration, pH value of the feed solutions, cosurfactant concentration, extraction time as well as temperature. In optimum conditions, the extraction ratio (E%) can reach 97.2%.

Mar 1, 2018

By M. K. Mohan

During the processing of metals like Cu, Ni, Co, large quantities of solutions, which contain co- products such as Sb, Cd, Pb etc. are generated. These solutions if processed to recover the metals help in conservation of metals as well as environment preservation. The present study was taken up to recover antimony from process solutions using zeolites. The effect of pH of the solution, time and type of zeolite viz., chabazite, mordenite, erionite and clinoptilolite on the sorption of antimony was investigated. Rate of sorption increases with pH and about 77-pct. antimony sorption was observed with chabazite at a pH of 6. Optimal conditions were established for the maximum recovery of antimony fiom process solutions. The mechanism of sorption for Sb was proposed in terms of adsorption and intraparticle diffusion. The calculated adsorption constants from Langmuir and Freundlich equations indicated that the adsorption of antimony on chabazite was strong.

Jan 1, 1999