Search Documents

By Xiangru Chen, Qijie Zhai, Wei Zhang, Haicheng Li, Chao Yang

In this paper, ductile iron material with different content of niobium was prepared by a scientific melting method. Image Analysis Software was used to studied the effect of niobium microalloying on both pearlite content and pearlite lamellar spacing in ductile iron quantitatively. The results showed that the addition of a small amount of niobium could increase the pearlite content and decrease pearlite lamellar spacing of ductile iron effectively.

Jan 1, 2015

By Payal Bakshi, Sangeeta Tiwari, Mohini Saxena, Anusha Sharma

"Recycling and reuse is perhaps the most favorable and beneficial way to solve the problem of industrial waste disposal. However, the use of industrial wastes like fly ash, tailings etc is in practice for brick manufacturing, land filling, embankments filling etc. These existing practices do not add enough value to the wastes. Moreover, some wastes may have very good potential to be incorporated in valuable products like paints. This study reveals about the value addition of industrial wastes like fly ash, copper tailing and blue dust as an extender in paints. Comparative properties and characteristics of these three wastes for application in paints are discussed. Fly ash, copper tailing and blue dust were characterized for physical, chemical and mineralogical properties and used in different paint formulation based on their potential to the particular application. Fly ash has been found very useful in enamel, primers and flat paints while copper tailing was found suitable in oil based paint formulations. The performance of fly ash and copper tailing paints were evaluated by comparing with those of conventional whiting extender. Blue dust was compared with conventional iron oxide for use in priming coats. The extender properties of these new material and paints prepared out of blue dust, fly ash, copper tailing, were found better than the existing related materials.IntroductionIndustrial development and environmental reforms should run parallel to benefit each other. This is the best policy, which must be adopted by industries for the sustainability of the current modern life. The high degree of industrialization and urbanization adds scads of waste resulting problem of pollution and challenges of their safe disposal. The nature of waste depends on the process that produces waste as its by-product. Therefore, policies/plans are prepared by keeping the view of possible potential hazards. Among the different wastes some are generated in the industries, which have great importance in the country’s economy, like fly ash waste from thermal power industry and mining waste. In India the total contribution of thermal power in the total electricity generation is more than 70% and it produces about 123 million ton of the fly ash annually [1]. On the other hand mining plus extraction of ferrous and nonferrous metals also produce waste in million tonnes of categories [2]. Since the generation of this waste is very high they cover large land area for their disposal and dumping [3]. The storage of this waste in the dumping sites for long time duration may cause problem of land, surface water, ground water and fertile soil contamination [4]. As far as Indian fly ash is concerned it does not contain toxic element over the limits of hazardous waste [5]. However, in general most of the metals deposits are found in the form of pyrite based ores. Mining wastes contain toxic elements e.g. heavy metals in varying amount, which get mobilized when pyrite get oxidized to sulphate producing sulphuric acid [6,7]. These ores contain very less amount of targeted metals in themselves thus they require extensive preprocesses for concentration of the metals [8]."

Jan 1, 2008

By Chen Song

Keywords: Co3O4, Cobalt Compounds, Morphology, Urea, Homogeneous Precipitation Depending on experimental condition, precipitation from cobalt nitrate and chloride solution in the presence of urea yield dispersed cobalt compounds with different chemical compositions and morphologies. The effects of concentration of cobalt solution and urea, agitation, on precipitation morphology were investigated experimentally. Generally in closed systems the particles are identified as cobalt (II) basic carbonate with needle type shape. In open system, spherical and plate-like precipitations of cobalt (II) basic cyanate are formed. The chemical formula of cobalt compounds was confirmed. They are CoII,III(OH)0.83(CO3)0.49 Ay?0.14 H2O (in tightly-capped reactor: A stands for NO3?, Cl?; y[A]molecular weight < 12.9) and CoII,III(OH)0.83(NCO)XAy?0.14 H2O. (in open reactor A stands for: NO3?, Cl?; 42 x + y[A]molecular weight < 44.82). The main reason was that the primary particles had different chemical compositions for the effects of the different kinds of anions and stoichio-chemical compositions of the primary particles. The effect degree of the anions depended on the co-existing anion radius in the reaction solution. According DTA-TG analysis of the cobalt compounds, the latter particles transform to Co3O4 powders on calcining. The shape of the Co3O4 particle with porous character has inheritance with precipitation. In this paper, it concludes that the particle formed by the principle of nucleation-aggregation in aqueous solution. The process of aggregation has played an important role in formation of particles. During calcination, the aggregation would be destroyed partly.

Jan 1, 2005

By Gjergj Dodbiba, Toyohisa Fujita, Takahiro Kikuchi, I-Chen Wu

"In order to separate molybdenum (Mo) from the high-level radioactive liquid waste (HLLW), Pb-Fe based adsorbents were synthesized. The adsorbents were precipitated by adding sodium hydroxide in mixture of 1 mol/L lead nitrate and 1 mol/L ferric nitrate aqueous solutions. Each precipitate was then filtered, dried and ground to obtain a fine powder, which has been used as an adsorbent. Two main parameters were considered when synthesizing the adsorbents, i.e. the pH value at precipitation of adsorbent precursor and the calcination temperature of Pb-Fe based adsorbent. Moreover, the structures of the synthesized adsorbents were investigated by means of an X-ray diffractometer.The experimental results indicated that the calcination temperature of the Pb-Fe based adsorbent has a great influence on adsorption capacity of the adsorbent for Mo. It was found that when the Pb-Fe based adsorbent was calcinated at 500 oC, the sorbed concentration of Mo was the highest.1. IntroductionThe high-level radioactive liquid waste (HLLW), arising from the reprocessing of nuclear fuel are generally immobilized in an alkali borosilicate glass matrix. Broadly speaking, alkali borosilicate glasses are the matrix of choice for the immobilization of the HLLW, since they permit vitrification of waste stream of variable composition, [1]. Within this frame, the incorporation of molybdenum (Mo) is of particular interest in the vitrification of HLLW. Molybdenum is know to have a low solubility in borosilicate glass compositions and its presence in excess results in the phase separation of a complex yellow molten salt during vitrification, [1]. The formation of so-called “yellow phase” material during the vitrification process is undesirable since it leads to the accelerated corrosion of the inconel crucible liners. Furthermore, the “yellow phase”, which is reported to contain also other fission products, is soluble in aqueous solution providing a potential route for the leaching of radionuclides from the vitrified waste, should it come into contact with water, [1]."

Jan 1, 2008

By F. G. Caballero, J. L. Gonzalez-Carrasco, S. Barrius, H. Carreon, M. Lieblich

"The grit blasting is a low-cost technique successfully used to enhance mechanical fixation of the implants through increasing their roughness. As a result of the severe plastic surface deformation, it produces subsurface effects such as grain refinement, hardening and compressive residual stresses which are generally evaluated with destructive techniques. In this research work, non-contacting and contacting thermoelectric power measurements are performed in blasted 316L VM and Ti-6AI-4V specimens using Ah03 and Zr02 particles which yield a coarse and a fine rough surface, respectively. This study correlates the microstructural changes induced by the grit blasting treatment and the limitations and advantages of each of the nondestructive thermoelectric techniques based on the Seebeck effect used to evaluate these biomaterials.IntroductionIt is well known that surface properties play an important role in metallic materials used in bio-medical applications. Since the biological response is correlated directly with surface properties it is comprehensible the intense activity in superficial modification by physics or chemistry methods in this field. Grit blasting, one of the most popular surface modification of metallic biomaterials, enhances the mechanical fixation of the implant through the increase in roughness [1-3]. Roughening is developed by bombarding the surface with a high-velocity jet of ceramic particles, being the final roughness a function of the processing parameters (pressure, distance, time, ... ) and blasting particles (nature, shape, size). As the plastically deformed surface layer tries to expand relatively to the intact interior of the specimen, residual compressive stress gradients develops perpendicular to the surface at shallow depths with a maximum value at a depth in the range of 5 to 60 µm. This surface treatment also may cause subtle variations in the subsurface material properties, such as increased hardness and grain size refinement, which are consequences of the significant plastic deformation through cold work. Blasted affected zones may extend to a depth of up to about 200 µm. The subsurface hardening and the near-surface compressive stress gradient playa beneficial role by retarding fatigue crack nucleation and further growth, ultimately extending the fatigue life of the metallic part [4]. In this work, two non-destructive thermoelectric techniques (NDTT), the non-contacting and contacting thermoelectric power measurements were used to analyze the subsurface induced changes on blasted Ti-6AI-4V and 316L VM specimens using Al2O3 and Zr02 particles. Detailed information on the microstructural induced effects and subsurface mechanical properties were published elsewhere [5-8]. Here the nondestructive evaluation of the involved microstructural changes is used to assess the global subsurface damage. Advantages of using nondestructive techniques during manufacturing are envisaged."

Jan 1, 2012

By Thomas Brynjulfsen, Merete Tangstad

"Manganese ore fines, generated during mining and transportation, can not be added to the submerged arc furnace directly as they will prevent even gas flow through the burden. Low gas permeability in the burden will lower the degree of pre-reduction of ore and subsequently increase the carbon and energy consumption of the process. In order to utilize manganese ore fines in the furnace they are agglomerated into sinter, pellet or briquettes. The agglomeration process will however change the reduction properties of the ore. In this work the melting and reduction properties of sinter has been investigated.The melting temperature and melting mechanisms has been studied. The mineralogy of the raw ores and agglomerated has been found using XRD, and the composition established using EPMA(WDS). The effect of adding fluxes such as dolomite and quartz has also been investigated.IntroductionManganese metal is produced in a submerged electric arc furnace or in blast furnaces. The reduction of manganese oxide in blast furnace has in the recent years become more unusual due to the high consumption of reducing carbon material[5]. Manganese metal for alloying in steel usually contains silicon and iron, and are therefore called ferro manganese and silicomanganese.During mining, transportation and handling the manganese ore is broken up into different size fractions. The larger lump are used directly in the electric arc furnace, but the finer materials can not be added without treatment. The fine ore can disrupt the flow of CO and CO2 gas through the burden, subsequently reducing the degree of pre-reduction. The fine fractions must therefore be agglomerated into larger lumps, in order to promote gas flow. This can be achieved through a number of different processes. The agglomerate used in this work has been sintered, which means that is has been partly molten and reduced, in order to create bigger lumps."

Jan 1, 2012

By Oleg I. Platonov

Method of high-temperature reduction of oxygen-bearing sulfurous gas has been developed at Copper Plant (CP) of MMC ?Norilsk Nickel? Trans-Polar Division (PD) with the aim of producing elemental sulfur from Vanyukov furnace? off-gas. Non-explosive reduction technology of oxygen-bearing sulfurous gas by methane utilized at Copper Plant has been designed to separate the processes of gas heating and sulfur dioxide reduction based on different kinetic of the reactions oxygen fixing and SO2 reduction. First, natural gas promptly reacts with oxygen contained in the process gas to heat a gas mixture up to the temperature of sulfur dioxide reduction (1200C). Then isothermal reduction takes place within 1 sec. Combustion chamber (pre-chamber) design developed based on the above principles is presented. Practical experience of the two reduction reactors operation at CP since 1996 proves high efficiency of the developed reduction process. The volume efficiency rises dramatically thanks to the fact that both fuel and reducing agent are fed into the reactor volume in the form of high-speed turbulent jets providing an intensive mixing of the reacting gases. On condition of equal internal volume of the reactors, the developed process offers higher efficiency of reagent interaction resulting in sulfur conversion exceeding 90%, as compared to the equilibrium one.

Jan 1, 2006

By David Roha, Øyvind Mikkelsen

"Significant resources have been spent throughout the years in the investigation of production of aluminum by carbothermic reduction. Due to the technological challenges involved, the efforts have not yet resulted in a commercial process. An initiative to overcome issues that prevented previous attempts to succeed was taken by Alcoa through the Advanced Reactor Process. The research program has resulted in technical developments which have resolved many of the previous issues. The knowledge about the process has continuously improved through physical and computer modeling as well as by experimentation at various scales. The technical achievements together with improved process understanding have resulted in a reactor design able to continuously operate the process for several weeks at the time, with hundreds of kilograms of alloy in every tap.IntroductionThe Hall-Heroult process has since its invention in the late 19th century, been essentially the only process used for commercial production of primary aluminum. The process has so far proved to be superior to all potential process alternatives and has continuously been improved. Although the Hall-Heroult is a reliable process it also has challenges:"

Jan 1, 2012

By Jin Qiu

Experiments were performed to determine the extent of minor element elimination that occurred when mixtures of copper smelter dust and copper concentrate, were calcined under vacuum. Almost complete removal of the As, Sb, Bi and Pb occurred due to the conversion of the minor element compounds of these elements into their highly volatile sulphides by reaction with sulphur from the concentrate. Heat and mass balance calculations of the slag-blow in a copper converter found that ~30 tonnes of the vacuum calcine could be used to produce 100 tonnes of copper as white metal. The use of dirty concentrate as the sulphidizing agent in the vacuum calcination means that the minor element treatment capacity of the smelter complex could be increased by 60 %. Also the productivity of the converters may be increased by up to 8 % due to the supply of copper values and oxygen in the calcined mixture.

Jan 1, 2005

By M. Pineau, G. A. Monteith, M. Laliberte, G. Houlachi

Conventional physico-chemical treatment methods, either hydroxide or sulfide precipitation, can hardly achieve a high removal of selenium from the liquid effluents which can be generated in some metallurgical operations. In weak acid solutions, selenium exists mainly as anionic species (selenite Se03-2 and selenate SeCV2) which, therefore, cannot precipitate as metal hydroxide or metal sulfide compounds. At the same time, neither selenite nor selenate form stable precipitates with the common cations (Ca, Mg, Fe, etc.) that are typically used in water treatment. At Noranda Inc., CEZinc Division in Valleyfield, Canada, the introduction of new discharge requirements for effluent toxicity initiated a R&D program which resulted in the full-scale implementation of a new treatment method for selenium removal. The goal of this paper is to present this new method which is now being patented by CEZinc. The process chemistry will be presented along with pilot-scale developments and full-scale operational results.

Jan 1, 2000

By Zhong Juya, Wang Yong, Guo Xueyi, Song Yu, Tian qinghua

"In this work, the flow of zinc in China, 2004, was traced within the STAF model, and the situation of production, consumption and recycling of zinc resources in China were introduced. The SFA is performed on zinc flows during its one year life cycle in detail. The result reveals that China produces and utilizes a large amount of zinc, while the efficiency of renewable zinc resources is still relatively lower. As one of the biggest producer and consumer of zinc in the world, China is facing a severe depletion of zinc resources. How to increase the resource efficiency is a significant issue for zinc industry of China. Based on the result, several advices were proposed in the paper, aiming to contribute important reference information for the industrial metabolism and resource management and recycling of zinc industry in China. IntroductionZinc is one of the important metals in national economic development in China; it has good conductivity and corrosion resistance, with high scalability when heated to 100 ~105_. Zinc is mainly used for galvanized zinc industry, as the coating of steel and various parts, and it has also been applied to the manufacture of brass, bronze and corrosion-resistant alloys, which are widely used in machinery manufacturing, printing, national defense and so on. In addition, zinc compounds are utilized in various fields, for example, ZnO is used for infiltration wood, paper, rubber, paints, etc.; ZnSO4 for leather, ceramics, textiles, medicine, etc.; ZnCl2 for infiltration wood; ZnS2O4 and Zn (HSO2 • CH2O) 2 for the paper and textile bleaching, etc. [1]. The extensive use and consumption of zinc in industrial production and social life promot the rapid development of zinc industry, which made zinc the third largest non-ferrous metals in the world."

Jan 1, 2008

By A. D. Neuman, C. C. Davis, M. R. Lopez, A. C. Martinez, T. A. Nothwang, F. G. Hampel, S. L. Voit

"One of the thrust areas for the Global Nuclear Energy Partnership (GNEP) program is the development of actinide bearing fuels for transmutation in a fast reactor. Mixed Oxide (MOX) fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition from which minor actinides can be incorporated for use as a transmutation fuel. The current study involves characterization of precursor powders and pellets destined for the Advanced Test Reactor in Idaho. These pellets will have three compositions: one standard MOX composition, (U0.80Pu0.20)O1.98, and two compositions of minor actinide mixed oxide (MAMOX) with oxygen to metal ratios (O/M) of (U0.75Pu0.20Am0.03Np0.02)O1.98 and (U0.75Pu0.20Am0.03Np0.02)O1.95. The precursor powders were characterized using a field emission gun scanning electron microscope (FEG-SEM) to determine particle morphology, size, and size distribution. An electron probe microanalyzer (EPMA) was used to characterize element distributions in the pellets.IntroductionThe fundamental purpose of GNEP is to enable a fuel recycling partnership between member nations. The customer nations utilize the fuel for electricity generation provided by and subsequently recycled by the supplier nation. The supplier nation recycles the actinide constituents, mainly uranium and plutonium, in advanced nuclear power reactors, and thus reducing waste volumes [1, 2]. Nuclear materials are strictly controlled through the International Atomic Energy Agency. One of the thrust areas supported by the GNEP program is the development of actinide bearing fuels for transmutation in a fast reactor under the U.S. Advanced Fuel Cycle Initiative (AFCI) in order to transmute long-lived transuranic actinide isotopes into shorter-lived fission products [3].MOX fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition into which minor actinides can be incorporated for use as a transmutation fuel [4]. Irradiation performance data on oxide fuels with high concentrations of minor actinides is limited, which has prompted this study. This paper discusses the characterization results of precursor powders and pellets prepared for the Advanced Test Reactor in Idaho to determine the effects of including minor actinides in the fuel, and addresses two fuel test matrices proposed by Hilton et al. [3]. The pellets will have three compositions: one standard MOX composition, (U0.80Pu0.20)O1.98, and two compositions of MA-MOX with O/M of (U0.75Pu0.20Am0.03Np0.02)O1.98 and (U0.75Pu0.20Am0.03Np0.02)O1.95. The precursor powders, uranium oxide (depleted, DUO2 and highly enriched, HEUO2), neptunium oxide, NpO2, americium oxide, AmO2, and plutonium oxide, PuO2, were characterized using a FEG-SEM for particle morphology, size, and size distribution. The morphology of the actinide powders was studied in the areas of flowability and porosity in order to predict manufacturability. The MOX pellets were characterized using an EPMA in order to determine impurity levels and locations."

Jan 1, 2008

By Min Xiaobo

As for treatment of zinc-containing wastewater, traditional SRB (Sulfate Reducing Bacteria) process was used, however, there exist two defects, like toxicity of heavy metal ions and high effluent COD (Chemical Oxygen Demand) value. In this study, a new technique, called ISIS process (Immobilized SRB sludge beads with Inner cohesive carbon Source), in which SRB sludge is embedded in carrier of PVA (Polyvinyl Alcohol) with carbon source that adsorbed on certain material, is put forward for the first time to overcome the two defects existing in traditional SRB process. Furthermore, it has been shown that compared to traditional SRB process, ISIS process increases average zinc removal rate up 30%, average sulfate reduction rate up20%, and decrease average effluent COD value to meet discharge standards. If activated carbon is selected for carbon source adsorption and fixing material, and PVA for immobilization material, the zinc removal rate can reach above 98% under the conditions of 35 and pH 6. Meanwhile, the mechanism of zinc removal has been determinated according to the results from SEM (Scanning Electronic Microscope) and XRD (X-Ray Diffraction).

Jan 1, 2006

By E. Gratz, U. Pal, A. Powell, S. Pati, J. Milshtein

"The solid oxide membrane (SOM) process has been used at 1150 'C to produce magnesium by direct electrolysis of its oxide. Magnesium oxide is dissolved in a molten CaF2-MgF2 ionic flux. An oxygen-ion-conducting yttria-stabilized zirconia (YSZ) SOM membrane separates the cathode and the flux from the anode. During electrolysis, magnesium ions are reduced at the cathode and Mg(g) bubbles out of the flux into a separate condenser. The flux has a small solubility for magnesium which imparts electronic conductivity to the flux. The electronic conductivity decreases current efficiency of the process and also degrades the YSZ membrane. This study investigates different methods for reducing the electronic conductivity of the flux due to magnesium solubility. One effective method shown here is inert gas flushing near the magnesium nucleation site. Potentiodynamic and potentiostatic experiments along with AC impedance spectroscopy are used to characterize the effectiveness of the approach.IntroductionMagnesium is the third most abundant metal in the earth's crust. Since magnesium is the lightest of all metals used for construction alloys, magnesium is the leading candidate to replace steel and aluminum in automobiles. Automobile manufacturers would like to increase magnesium content from 4-5kg per vehicle to 40-IOOkg per vehicle [I]. Using magnesium alloys instead of steel and aluminum can reduce automobile weight and improve fuel efficiency. However, in order for automobile manufactures to make this change, it is generally believed that new cost effective methods of magnesium production must emerge.One approach for magnesium production which has been shown to be effective on a laboratory scale is the direct electrolysis of magnesium oxide utilizing an oxygen-ion-conducting solid oxide membrane (SOM), this is known as the SOM process [2]. A recent study estimated that a commercial SOM plant could produce magnesium from magnesium oxide at a cost that is 40% less than current technologies [3]."

Jan 1, 2012

By R. P. Rao

In rare earth (RE) based phosphors, high luminous efficiency is possible due to their restricted emission limited to specific narrow bands. In general, these phosphor materials consist of RE ions as activators/sensitizers and/or hosts. Development of various phosphor host matrices such as alkaline earth chlorophosphates, aluminates and silicates activated by Eu(2+) as blue component, borates and phosphates of lanthanides and alkaline earth aluminates doped, with Ce/Bi and Tb as green component and Eu(3+) activated yttrium oxide and vanadate as red component has been described. Luminescent characteristics, color coordinates and suitability of these phosphor materials in high efficiency new generation lamps are presented and discussed.

Jan 1, 1989

By Ibrahim Yusufoglu, Cem Kahruman, Sedat Ilhan, Ahmet Orkun Kalpakhi

"Scheelite is the main raw material in tungsten production. In hydrometallurgical processes, extraction of tungstate ions into solution is very important. During the leaching of scheelite in oxalic acid solutions, tungsten dissolves as a chelate complex. Scheelite includes impurities along with calcium tungstate. Determination of the dissolution of these impurities is important in the subsequent tungsten production stages. In this study, scheelite was dissolved in oxalic acid solutions and the dissolution of impurities was investigated. The quantities of dissolved impurities were determined by ICP - OES and characterization of the undissolved impurities in the leach residues was carried out by SEM - EDS analysisIntroductionScheelite and wolframite ores are used for the industrial production of tungsten. Both ores are dissolved in acidic or basic solutions, and ammonium paratungstate is obtained as an intermediate product. Prior to crystallisation of ammonium paratungstate, all the impurities must be removed. Among these, Fe, Si, P, Mn, Mg and Mo are classified as ""harmful"" elements and different methods are used for their removal [1]. During purification, solvent extraction, ion exchange, etc. methods are used.Potashnikov et al. [2] studied the dissolution of scheelite in acidic solutions and the effects of stirring speed, temperature and oxalic acid concentration on the dissolution kinetics.There are no works in the literature about the removal of impurities from scheelite ores in oxalic acid solutions. Therefore, the aim of this work was to investigate the dissolution mechanisms of impurities during the leaching of scheelite in oxalic acid solutions. The effects of temperature and oxalic acid concentration on the dissolution were also investigated. In addition, the characterization of the impurities which were not dissolved was studied."

Jan 1, 2012

By Kiichiro Hayashi

"Indonesia is one of the world leaders in palm oil production. Palm oil industry is an industry to be considered when it comes to environmental impacts. This paper utilizes three step approaches. First, a material flow analysis of palm oil related industry was conducted in Indonesia. Second, a factory visit survey was conducted for getting information on environmental impacts of plantation and CPO mills. Third, a LCA study was made for a model Indonesian CPO mill in several bio-waste treatment options. Main findings were that, first; over 70% of FFB was bio-wastes generated from CPO mills. Second, some mills introduced a zero emission bio-waste policy. However, untreated bio-wastes in the zero emission policy, such as, CH4 from POME ponds, may have potential to reduce more impacts on the environment. Introduction Indonesia is one of the world leaders in palm oil production with approximately 12.4 million tons of crude palm oil (CPO) production in 2005 and with the plantation area 5.6 million ha spreading out in 19 provinces [10]. The expansion of palm oil cultivation in Indonesia and its export oriented industry heavily relies on the strong world market demand for food. Currently, there are 320 CPO industries in Indonesia [10]. These include plantations and palm oil related factories. Among them, there are six biggest players in CPO business in Indonesia: PT. Perkebunan Nusantara (PTPN) consisting of 9 PTPN, Sinar Mas, Raja Garuda Mas, Astra Agro Lestari, Minamas Plantation and Indofood. They are managing more than 50% of plantation estate in Indonesia and are leading the Indonesian palm oil business.Palm oil industry is an industry to be considered when it comes to environmental impacts. Unfortunately, there is not so much available information related to the performance of each CPO on environmental impacts. There are reports which provide information on environmental impacts of CPO mills in South East Asian countries, but are limited to, for instance, Thailand’s cases [4 and 5] and Malaysia’s cases [1, 3, 6, 7, 9, 11 and 12]. On the other hand, similar studies on the Indonesian’s case are not well established in academic literatures. And also there is limitation on Indonesian palm oil industrial information from plantation to consumption and disposal in academic articles. There is no literature related to material flow analysis focusing on the whole Indonesian palm oil related industry. One way to describe and present the environmental impacts is through a life cycle assessment (LCA). The LCA could be used to estimate the impacts of CPO production including the stages of plantation, transportation and milling [5, 8 and 11]. However, studies on Indonesian CPO production process were not well established in academic articles. The purpose of this paper is thus to clarify environmental impacts of palm oil industry in Indonesia especially by focusing on plantation and CPO mills with consideration to various bio-waste treatments."

Jan 1, 2008

By Min Chen, Lei Xu, Weijun Huang, Shuai Zhang

For the purpose of extending the service life of MgO-C bricks used as linings of vanadium-extraction converters, the effect of Fe addition on properties of MgO-C bricks was investigated. The results showed the addition of Fe could effectively improve the sinterability of the oxidized layer of the MgO-C refractory at 1400°C due to the effect of FeO (formed by oxidation of Fe) on formation of MgO-FeOss and modification of the microstructure, and excellent corrosion resistance against vanadium containing slag was also obtained due to the increase of compactness of the oxidized layer and concentration of FeO in the oxidized layer. Consequently, it is considered that MgO-C brick by introducing the new phase of Fe is a favorable substitute of MgO-C refractory to be used as linings of vanadium-extraction converters.

Jan 1, 2015

By Camila Martini Matos, Maria das Graças da Silva Valenzuela, Francisco Rolando Valenzuela Diaz, Lucy Gomes de Sant' Anna, Orley de Oliveira Magalhães, Flavio M. S. Carvalho, Isaac Jamil Sayeg

"Kaolin clays are widely used in various industry segments. Its main properties are fine granulometry, chemical inertness and whiteness. In general, kaolins are not easily organophiilized as a result of its 1: 1 structure. The aim of this paper is to describe the modification of a Brazilian kaolin sample, in order to obtain an organophilic kaolin of high performance. The clay as received was identified by X-ray diffraction and characterized by optical microscopy, cation exchange capacity and swelling tests for observation of their performance in water and organic solvents. Then, the sample was treated with a 10% sodium carbonate solution and with ammonium quaternary, washed several times with distilled water, dried at 60°C, and characterized by XRD and swelling assays. Our results show that the clay was organophiilized and its ability to swell in organic solvents has increased.IntroductionThe kaolin clay, also known as ""china clay"" is chemically a hydrated aluminum silicate characterized as a very fine powder and lamellar structure (1:1), being constituted mainly by kaolinite [l]. Kaolin is a mineral extremely used as raw material. Its properties such as color, softness, small particle size and chemical inertness make it a suitable material for several industrial applications. The desired properties of kaolin varies widely for each application, beginning with its largest use in the paper industry until minor uses in the sectors of cosmetics and pharmaceutics. These two last applications require purified kaolin with defined functionality [2]. To find improvements in the functionality of kaolin for specific applications is important for many industrial uses. Sometimes the way to find these improvements might be modification of the kaolin clay by treatment with a chemical substance as ammonium quaternary, causing surface modifications [3,4]. In this work is described the modification of a Brazilian kaolin sample by treatment with cetyl trimethylammonium chloride (CTAC). The properties of the modified kaolin are being assessed by characterization and essays to understand its functionality and industrial application."

Jan 1, 2013

By Munetaka Iwasaki

Nitrogen strongly affects mechanical properties of steel and therefore we may sometimes modify the various processes for its content. Numerous studies based on the results of chemical analysis of quenched samples were reported with a few exceptions of Hot Sievert method. The technique always poses a risk of uncertainty whether the true content of nitrogen in liquid metal is measured or not. In this study vacuum remelting under relatively low pressure was done to enhance gas phase mass transfer. Total pressure of the melt chamber was about 10-3 pa and electron beam heating was used. Mass spectroscopy was used for the direct observation of the rate of denitrization. Nitrogen molecules or atoms were detected by a mass spectrometer set above the melt. Continuous monitoring of the intensity of the fixed mass number may reflect the transfer of nitrogen from the melt to the vacuum. The results of the new and conventional techniques agree, both technique can be verified.

Jan 1, 1999