Search Documents

By He Jing, Wang Changhong, Chen Yongming, Wu Yanzeng, Yang Xiyun, Tang Chaobo, Yang Shenghai

Pitting of Hf in Et4NBr t-butanol and acetonitrile (ACN) solutions was studied by means of cyclic voltammetry, potentiodynamic anodic polarization,galvanostatic, potentiostatic and impedance techniques. The potentiodynamic anodic polarization curves did not exhibit an active dissolution region near corrosion potential due to the presence of an oxide film on the electrode surface, which was followed by pitting corrosion resulting from the passivity breakdown by the aggressive attack of bromide (Br−) ion. The pitting potential (Epit) increased with increasing potential scanning rate but decreased with increasing temperature and Br− concentration. Cyclic voltammetry and galvanostatic measurements allowed the pitting potential (Epit) and the repassivation potential (Ep) to be determined. Analysis of the potential/time transients revealed that the applied anodic current density had a significant influence on the values of Epit. On the other hand, the Ep values were independent on the applied current density. The current/time transients indicated that the incubation time (ti) for passivity breakdown decreased slightly with increasing potential and solution temperature. The impedance spectra showed that the resistance of passive layer decreased with increasing potential.

Mar 1, 2017

By Cledwyn Mangunda

Mining operations generate Acid Mine Drainage (AMD) that poses a significant threat to the natural environment. AMD treatment using Ca(OH)2 leads to the precipitation of a sludge dominated by a mixture of ferri-oxyhydroxides. This sludge has poor dewatering tendencies and is deposited in landfills with potential for metal remobilization. This study investigated the dewatering behaviour of a precipitate formed during elevated temperature treatment of a primary, pre-settled sludge from the neutralisation of aqueous acidic Fe2(SO4)3 and Ca(OH)2 solutions in an MSMPR reactor. The resulting treated precipitates were analysed for micro-properties, with results showing that an increase in the secondary reactor temperature from 25 °C up to 50 °C led to an increase in mean particle size, a decrease in the number of particles and improved dewatering behaviour at a ferric concentration of 300 mg/L. This was ascribed to the attainment of a circum-neutral surface charge that favoured agglomeration and a change in micro and nano-structure that allowed for better water passage.

By Mikiya Tanaka, Mikio Kobayashi, Mansour A. S. A1Ghamdi, Kenji Tatsumi, Yukinori Saiki, Hirotaka Senba

"In order to recover nickel ion in a spent electroless nickel - phosphorus alloy plating bath and, at the same time, to remove impurities such as iron and zinc, the applicability of solvent extraction with LlX84I as the extractant has been investigated using actual spent solution. Although the extraction efficiency of nickel from the spent solution is considerably lower than that from the nickel sulfate-nitrate solution, nickel in the spent solution is selectively extracted with high efficiency at the pH of 6 - 7. The extracted nickel is effectively stripped by sulfuric acid at a pH of less .than· 3. On the basis of these results, a· flowsheet for recovering nickel from the spent solution is proposed Chemical equilibrium calculations of the spent solution has shown that the complex formations of nickel with anions such as lactate and phosphonate ions become predominant in the pH range between 2 and 6. This results in the depression of nickel extraction efficiency from the spent solution as compared with that from the .nickel sulfate-nitrate solution. By combining these aqueous equilibrium calculations with the· extraction model considering the extraction stoichiometry and the aggregation of the extractant in the organic phase, the extraction behavior of nickel is quantitatively predicted.IntroductionElectroless plating is indispensable for the recent advanced industries such as the electronic and mechanical industries. Electroless plating baths are repeatedly used by supplying the metal salts; however, the accumulation of the counter anions of the metal ions, the components formed by the oxidation of the reducing reagents in the plating baths, and the metal ions as impurities dissolved from the surface of the objective materials degrades the· quality of the plating. Thus, the baths are finally treated by a precipitation method to form a large amount of metal sludge, which is disposed in dumping sites. Therefore, from the standpoints of environmental protection and resource preservation, it is highly desired to establish a recycling process of the plating baths with minimum emission. Solvent extraction seems to be one of the 'suitable methods to recover metals from the spent electroless plating baths, because the concentration of the metal ion in the baths is relatively high, which is advantageous to solvent extraction as compared with the ion-exchange and adsorption methods. Some studies about the application of solvent extraction have already been carried out using simulated spe11t electroless plating baths [1-3]."

Jan 1, 2000

By B. G. Thomas

"Mathematical process models can be applied in several different ways to serve industry by inducing beneficial changes to process operation. This paper attempts to summarize the different uses, types, and attributes of these models, and to offer some ideas to consider when developing, using, and reporting on them. Process models range from empirical to mechanistic in nature and vary in complexity from simple analytical solutions to coupled, 3-D transient numerical simulations. They are classified here according to the way in which they are implemented in practice, viz. fully-online models, semi-online models, off-line models, and literature models. The purpose of the model should dictate how choices are made during its development. Ways to validate and compare the model with experiments are suggested. Examples are taken in the context of the author's experience in modeling the continuous casting of steel.IntroductionThe objective of this paper is to provide a partial introduction for this symposium by discussing some basic aspects of the application of mathematical process models in industry. Essentially, the aim is to explore how process models are used to benefit industry, and to offer some general comments and suggestions, based on the experience of the author, on how models can best meet this goal.This work is concerned with process models, which consist of systems of mathematical equations and constants that are solved on a computer to make quantitative predictions about some aspect(s) of the process. The specific variables required as input data and generated as output data are important features of the model. The equations often derive from a numerical solution to one or more differential equations and their boundary conditions. The model also includes the constants, which represent material properties, empirical relationships, and other knowledge about the process, and usually require considerable effort to obtain. Thus, general purpose commercial software packages, (ie. finite-element or finite-difference based codes), are not models in this context. They are useful tools, however, serving as frameworks for the development of process models."

Jan 1, 1994

By Graham J. C. Carpenter, Marc Charest, Jason Lo

"The method of producing magnesium-based composites with silicon carbide (SiC) particulates embedded in the matrix of magnesium AZ9I D alloy by the squeeze-casting technique are described. This method involves the fabrication of a SiC particulate preform and the subsequent squeezing of molten magnesium into the preform. In this study, alumina, aluminum phosphate and a proprietary binder were used for the fabrication of SiC particulate preforms. The procedures employed in the fabrication of SiC! AZ9ID composites are presented, together with the results of characterization of the composites using optical and transmission electron microscopy. Special attention is given to the reaction products in the bulk alloy and at the interfaces between SiC particles and the AZ9ID matrix alloy.1. IntroductionInterfacial, microstructural and metallurgical characteristics play an important role in determining the mechanical properties of a composite. In theory, reinforcing magnesium with SiC particulates should provide an improvement in strength and modulus of the composite over the unreinforced counterpart. However, many factors resulting from the fabrication process can cause degradation rather than improvements to the mechanical properties. In particular, the interfacial characteristics are known to critically influence the properties of composites [1]. Before evaluating the mechanical properties of a composite, it is always useful to examine the microstructure, which is closely related to the mechanical behavior. This helps to reduce the labor-intensive steps of sample preparation for mechanical property evaluation, which can be particularly difficult as a result of the high hardness of composite materials, as well as providing a wealth of information on the microstructural and interfacial characteristics, particularly the reaction products caused by processing. This information is also pertinent in understanding the factors governing the mechanical properties of the composites.There are many factors which determine the nature of the interfacial characteristics of a SiClMg composites. Qualitative estimations of the interfacial bonding have been performed based on thermodynamics, electronic and electrostatic concepts. In addition, the kinetic conditions during the fabrication play an important role. From an interfacial energy standpoint, the driving force for the formation of a metal/ceramic interface is the decrease in free energy that occurs when intimate contact is established between metal and ceramic surfaces. The simple representation of the energy change per unit area of interface formed (~G) is given by Dupre equation [2]:"

Jan 1, 1996

By Bohumir Jelinek, Sergio Felicelli, Mohsen Eshraghi

"We present a parallel lattice Boltzmann - cellular automaton model of the two-dimensional dendritic growth during solidification of binary alloys. The model incorporates effects of solute and energy transport under melt convection. The parallel performance of the algorithm is assessed. A loss in the parallel efficiency is observed when multiple computational cores per processor are utilized. Excellent strong scaling up to thousands of computing cores is obtained across the nodes of a computer cluster, along with the near-perfect weak scaling up to forty thousand cores. The presented solidification model shows a good scalability up to centimeter size domains, including millions of dendrites.IntroductionLattice Boltzmann method (LBM) is an attractive numerical technique for solving fluid dynamics problems. Its advantages are simple formulation and locality, with locality facilitating parallel implementation. In the present model, interface kinetic is driven by the difference between local actual and local equilibrium liquid composition [1]. The cellular automaton (CA) technique is deployed to track the solid-liquid interface [2]. A serial version of the present LBM-CA model with a small number of dendrites was validated against theoretical and experimental results in the previous publications [3, 4]. In this work, it is the first time that simulations with millions of dendrites were performed, something not possible with the computationally much more costly phasefield method [5].This research effort examines a technique for simulations of millions of dendrites in centimeter size domains, including thermal, convection, and solute redistribution effects. Nearly ideal scaling properties of the model are demonstrated. This extensively large landmark was achieved because of• the CA technique being two orders of magnitude faster than alternative, phase-field methods [5]• highly parallelizable LBM method, convenient for simulations of flow within complex and time dependent boundaries• availability of the powerful NSF Extreme Science and Engineering Discovery Environment (XSEDE) supercomputing resources"

Jan 1, 2013

By J. Brent Hiskey

Recently basic concepts of semiconductor electrochemistry and solid-state electronic structure theory have been applied to the dissolution of mineral electrodes. In this paper, fundamental aspects of semiconductor electro- chemistry and interfacial charge-transfer processes are reviewed. Information regarding the electronic and semiconductor properties of chalcopyrite is summarized. The electrochemical response of chalcopyrite in acidic solution is analyzed in terms of initial dissolution processes. The initial charge- transfer reaction involves the consumption of holes. It has been shorn that Fermi level pinning is consistent with observed electrochemical and dissolution behavior. Semiconductor electrochemistry has proved helpful in explaining the formation of intermediate surface films produced during the initial stages of chalcopyrite dissolution

Jan 1, 1993

By Ryo Sasai, Takeshi Itakura, Haruki Imaizumi, Hideaki Itoh

"Emission of industrial wastewater containing harmful oxoanions is one of the serious problems on account of its toxicity and the environmental pollution, especially caused by boric, phosphinic, arsenic and antimonic species. In this study, we developed a novel treatment technique of such polluted-water by hydrothermal mineralization. The treatment is “Geomimetic” method for precipitating oxoanions in aqueous media as natural ore resources by using hydrothermal treatment with calcium salts mineralizer. The treatment made it possible not only to detoxify the polluted-water, but also to recover the calcium minerals such as Ca2B2O5·H2O, Ca5(AsO4)3(OH), etc. Concentration of each ion in treated-water was lower than that of effluent standard in Japan. Moreover, the residual concentration of each ion was independent of the initial concentration, but it depends only on the solubility of the formed mineral under hydrothermal condition. Therefore, the hydrothermal treatment could be recommended as one of the treatment techniques of polluted-water.IntroductionVarious oxoanions such as boron and arsenic oxo-anions have high toxicity against human health and the environment. They are important resources, however, for plating or advanced material manufacturing industries[1-3], from which the wastewater containing these oxoanions is generated every day. An appropriate treatment is often required for industrial wastewaters to attain national effluent standards of Japan (NESJ, B: 10 mg/dm3, As: 0.1 mg/dm3). On the other hand, there is no production of arsenic and boric resources in Japan, and they are expected to be recycled. Therefore, the establishment of a system for the removal and recycling of arsenic and boron from wastewaters is of global significance.Several methods to remove them from aqueous media have been already reported by using adsorption[4], electro-coagulation[5], membrane separation[6-8] and biological techniques[9]. However, these methods have the following problems because of their stability in water. (1) Removal yield is low, especially for tri-valent arsenite ion (AsIIIO3 3-) and borate ion. (2) The applicable concentration range is narrow. In addition, the used adsorbents or collected residues after treatments are sill hazardous wastes, so that they must be treated by a proper method. But, it is very difficult to convert them to recyclable resources at most industrial plants. These problems are caused by the difficulty to recover these oxoanions as stable solid precipitates with low solubility in water. The establishment of recycling system of these hazardous compounds will be one of the world-important issues, especially, in Japan, which is poor in natural resources. On the other hand, compounds that contain high arsenic concentrations and are insoluble in water, are often found in natural minerals, for example, as haidinglite (Ca(AsO3OH)·(H2O) or Johnbaumite (Ca5(AsO4)3(OH)). This fact suggests that nature has an ability to produce insoluble As-bearing minerals. Similar phenomena can be found in case of boron, antimony, etc."

Jan 1, 2008

By Chao Du, Xiaohui Ning, Hongmin Zhu, Qiuyu Wang, Shuqiang Jiao

"TiCxOl-x solid solutions were synthesized by sintering a mixture of titanium carbide and titanium monoxide at 1600 °C. The corresponding structures and morphologies of the TiCxOl-x solid solutions were characterized by XRD and SEM. A series of tests has been performed on the electrochemical dissolution behavior of TiCxOl-x solid solutions in NaCl-KCl molten salt. The influences of synthesis time and electrokinetic parameters on the anodic dissolution behavior were also investigated. The results showed that TiCxOl-x solid solutions can dissolve as Tin+ into alkali chloride melt. Titanium ion species dissolved from TiCxOl-x solid solutions changes between Ti2+ and Ti3+ depending on the applied potential. The tail gas on the anode was monitored by a mass spectrometer. It was found the synthesis time significantly affects the components of the anodic gas.IntroductionTitanium and titanium alloys have been desired greatly because of their many uses. The critical factor that restricts the range of uses for Ti is its high cost of extraction. The primary titanium metal, sponge titanium, is still produced industrially worldwide by a process invented by Dr. Kroll in the 1940s[1] •Since the early 1970s, the research focus of the titanium industry has been directed towards developing a continuous process to produce high purity titanium at low cost. [2-10] Of the many alternative methods that have previously been investigated, the electrolytic process has been considered a promising method for titanium metallurgy [4-10]. Recently, several electrolysis and related methods such as the PFC-Cambridge process[11-15], calciothermic reduction[16-18], USTB [19,20] and MER[21] process were extensively investigated.The USTB process is a new approach where the pure titanium can be directly obtained by the electrolysis with an anode of titanium oxycarbide in molten salts[19, 20]. The titanium oxycarbide was produced by carbothermal reduction of titanium dioxide under vacuum at a temperature"

Jan 1, 2011

By A. M. T. S. Bandara

The solubility of rare earth (RE) salts in aqueous solutions depends on many factors including the type of cations and anions in solution, their concentrations, temperature and the type of solid precipitated. Experiments were conducted using anhydrous La2(SO4)3 and Ce2(SO4)3⋅8H2O as solids and lanthanum(III) perchlorate prepared by dissolving La2O3 in HClO4 solutions as RE-sources. Solutions of H2SO4, H3PO4 and their mixtures in the presence or absence of Na+, Ca2+, Fe(III) or Al(III) as perchlorates served as test solutions. Saturated solutions and precipitated solids were assayed and characterized using standard techniques to show that the La(III) and Ce(III) ions precipitate as hydrated sulphates, phosphates or double salts with sodium, depending upon the solution composition. The change in solubility of RE-salts with solution composition and temperature is the result of the composite effect of changes in solubility products (pKSP) of salts, pKa of acids and other equilibrium constants for ion-association.

By Fathi Habashi

The recovery of uranium from wet process phosphoric acid was applied on industrial scale in the 1940's by using octylpyrophosphoric acid as an extractant. Later, more efficient reagents were used, e.g., di(2-ethylhexyl) phosphoric acid and actylphenyl phosphoric acid. In the 1970's the rare earths in Kola phosphate were recovered in Finland and recently (1997) in Norway using HNO, as a leaching agent and di(2-ethylhexyl) phosphoric acid as solvent. It was demonstrated later on laboratory scale that both uranium and rare earths could be extracted from the rock by tributyl phosphate but at different pH values provided that the rock is leached with nitric or hydrochloric acids instead of the commonly used sulfuric. This new concept opens the way to the possibility of treating phosphate rock by in-situ, dump, or vat leaching for the recovery of phosphate values as well as uranium and the rare earths. Another solvent extraction process is used industrially for the purification of phosphoric acid using butyl and amyl alcohols.

Jan 1, 1998

By Konstantina Chalastara

Mixed phase titanium dioxide (TiO2) nanoparticles synthesized through hydrolysis of TiCl4 solution at different conditions, namely concentration, pH, and residence time are characterized and evaluated as photocatalysts. The process is operated in a continuous stirred-tank reactor, CSTR giving blends of anatase, brookite, and rutile nanoparticles that were further evaluated to find the optimum mixture for a photocatalytic sorption material. The titania nanoparticles are first characterized in terms of photocatalytic activity under UV light illumination using an organic model compound (methyl orange) and after that are tested for removal of toxic selenate and selenite species from simulated effluent waters.

By Gordon D. Jarvinen

Polymer Filtration (PF) Is an innovative, selecthle metal removal technology. Chelating, water-soluble polymers are used to selectively bind the desired metal ions and ultrafiltration is used to concentrate the polymer-metal complex producing a permeate with low levels of the targeted metal ion. When applied to the treatment of, Industrial metal-bearing aqueous process streams, the permeate water can often be reused within the process and the metal ions reclaimed. This technology is applicable to many types of industrial aqueous streams with widely varying chemistries. Application of PF to 'aqueous streams from nuclear materials processing and electroplating operations will be described.

Jan 1, 1999

By Huimin Lu, Qiang Li, Jingbo Xu

"The smelting reduction of V-Ti bearing beach placer by combined rotary hearth furnace and direct current arc furnace was studied in laboratory. It takes the aid of back propagation (BP) neural network theory to build the nonlinear mapping relations between the crucial process variables such as content of carbon, temperature and time and the degree of reduction. Then by the integrating BP neural network and genetic algorithm (GA), the optimized process parameters for the high degree of reduction were searched. The comparisons between experiment results and neural network simulation results show that GA-based on BP method can predict the degree of reduction with higher prediction accuracy. Calculations show that the integrated energy consumption of new technology is 580kgce/tHM, less than the current existing blast furnace.IntroductionThese V-Ti bearing beach placers (VTBBP) are secondary Fe-rich minerals formed by rivers, ocean waves, ocean tides and ocean currents on beach zones, their useful minerals are V-Ti magnetite ores. On Asia Pacific zone, such as Japan, China, Philippines, Indonesia, Australia and New Zealand, the VTBBP have large reserves and wide distribution. But so far, the VTBBP are not still comprehensively utilized. Therefore, in this paper, a combined rotary hearth furnace technology and arc furnace smelting method is studied for comprehensive utilization of the VTBBP. The main objective of this paper is to find optimum operation conditions for the production ofV-bearing iron and titania-rich slag from the VTBBP by means of the laboratory testing.Recently, neural network (NN) expected to be able to provide an effective tool because of its advantages, which describe nonlinear mapping relations. With the characteristics of strong selflearning, self-organization, robust error toleration and accurate nonlinear relation approximation, artificial neural network can be applied to nonlinear process modeling based on sufficient training. Back-propagation (BP) training algorithm is probably the frequently used one in practical application. Genetic algorithm has parallel search strategy and global optimization characteristics, which makes the trained neural network being higher classification accuracy and faster convergence speed. So it is necessary to combine neural network and genetic algorithm. The nonlinear relationship between input and output presented by NN and the global optimal function of GA are abroad applied in the engineering and scientific research [1, 2]. So these methods supply an efficient path to solve the above problems. At present, it is common to study the optimization of process parameters by orthogonal experimental design, the method combining neural network and genetic algorithm is a novel and better method than orthogonal experimental design. Tills study organized the above advantages to optimize the process parameters for comprehensive utilization of the VTBBP."

Jan 1, 2012

By Paponetti B. . A.

Gold is usually recovered by cyanidation, thiourea leaching and amalgamation, however the efficiency of these technologies, in the case of refractory ores, is low ever when fuie grinding is practised. For example, .if the gold particles are included in sulphide minerals, the leachant cannot reach them, so they are often lost in the tailings. Hence .it is first necessary to break the sulphide crystals by preliminary treatment such as roasting, nitric .acid oxidation, pressure leaching and bacterial oxidation and then apply a conventional extractive technique for satisfactory gold recovery. This paper describes the effect of biological pre-treatment with Thiobacillus ferrooxidans) on the? extraction ? and? recovery of gold by conventional cyanidate. leaching from; a refractory arsenopyrite ore from Golcuck (Turkey).

Jan 1, 1991

By Xiao-hui Fan, Xu-ling Chen, Xiao-xian Huang, Gui-ming Yang

Grate-kiln-cooler is a predominant process of producing iron ore pellets in China. Since this process is of multi-variant, strong coupling and large hysteresis characteristics, a reliable performance monitoring is thus essential to ensure product quality and economic benefits. Aiming to efficiently monitor the pellet induration within this process, this study proposed an approach that combines statistical analysis and quality soft-measurement. Soft-measurement of pellet quality was accomplished based on the predicted time-temperature profile, and the soft-measured indices were on-line monitored using statistical control charts. Based on the proposed approach, a monitoring system for grate-kiln-cooler thermal process was developed for a domestic pelletizing plant. Running results demonstrate that our system can assist in the detection or diagnosis of abnormal thermal state and finally helps to stabilize the pellet production.

Jan 1, 2016

By J. T. I. Poijärvi

Outokumpu Harjavalta Metals Oy operates copper and nickel smelters, three sulphuric acid plants and nickel refinery at Harjavalta and copper refinery and precious metal plant at Pori. The by-products of these plants are presented in this paper. The by-products of the smelters include products from slag cleaning of flash smelting furnaces and converters, flue dusts and smelter off-gases. Weak acid and sludges from cleaning of smelter off-gases and acids are the by-products of the acid plants. The by-products out of the copper refinery are crystallized metal sulphates and sludges from electrolyte purification, on which a co-production process of the copper tankhouse is based. The main by-products of the precious metals plant are products from anode slime treatment and platinum metal group concentrates in the recovery of precious metals. Sludges from nickel matte leaching and precipitates from solution purification are the by-products of the nickel refinery. The formation, treatment and processing as well as the research work done for the utilization instead of dumping of the by-products in the production of copper and nickel will also be discussed in this paper.

Jan 1, 1995

By S. M. Copley, M. Yankova, E. Y. Yankov, J. A. Todd

"Nanophased coupled growth structures, with spacings of -10 nm, have been observed in banded microstructures produced by laser melting hypoeutectic Ag-Cu alloys. These coupled growth structures comprised a Cu-rich phase of width - 1 nm and a Ag-rich phase of width - 9 nm. In this paper, microstructural observations of nanophased coupled growth structures in hypo eutectic AgCu alloys are presented. Laser beam velocities for the transition from banded to microsegregation free microstructures are modelled and compared with experimental values. Models are presented to show that, at a critical undercooling, initial growth of a Ag-rich, metastable, extended solid solution is rapid but slows to a halt as copper is partitioned into the liquid at the solid/liquid interface. Following nucleation, the coupled growth structure then grows until the partitioned copper is consumed, at which point growth of the Ag-rich solid solution is again accelerated. This cycle then repeats resulting in banded microstructures comprised of 750 nm of the Ag-rich extended, metastable solid solution, followed by 250 nm of the coupled growth structure.1. Structural Studies of Laser Melted and Resolidified TrailsPresented here are observations of laser melted and resolidified trails in Ag-Cu alloys obtained at beam velocities ranging from 0.7 to 34 cm S·I. When the laser beam is scanned along the surface (positive x-direction) with a velocity Vb a melt pool with the shape given in Fig. 1a moves with the beam. The isotherms move with the velocity, Vi,. = Vb cos.p. Calculations employing the thermal analysis of Kou, Hsu and Mehrabian [1] for the beam velocities of this investigation and for the thermal properties of AgCu alloys, indicated that, .p, the angle between the isotherm velocity and beam velocity should be small at the surface where microstructural studies were made. This prediction was supported by observations of trail cross-sections. Based on these observations, and the calculations which include latent heat effects, the isotherm velocity for observations near the surface in our investigation was taken to be 27 cm S-I."

Jan 1, 1994

By Sandra M. Stash

An integrated copper production complex includes mining, milling and smelting facilities which are usually at or near a common site, and sized to complement one another in capacity. There may also be an electrolytic retlnery serving the complex, but not always totally dedicated to its production. Mines and mills without co-owned smelters are not usually considered integrated. The first marketable product of an integrated complex is blister, or in some cases electrolytically refined copper. The nature of integrated operation brings together all of the environmental issues associated with copper production, but currently operating and newly planned facilities are required to anticipate these issues and meet stringent regulations. Older complexes, however, may have legacies of 50 or more years of operation unencumbered by current levels of environmental strictures: nevertheless, they must be remediated. Using examples from closure and remediation of the mining and mineral processing facilities in the Upper Clark Fork River Basin of Montana, the authors review some of the problems encountered since CERCLA's1 enactment in 1980, and the solutions to those problems, bearing in mind that not all of the problems and solutions were technical. Much has been written about the mines of Butte -the "Richest Hill on Earth" as it was known in its day and the mills, smelters and refineries they spawned. These facilities comprised an archetype of the integrated copper complex: from ore to metal in facilities serving and depending on one another. Many great stories of technological innovations and business triumphs have been told about Butte and Anaconda's mining history and the place The Anaconda Company occupies in that history. However, relatively little has been written about the final days: 25 years during which the once-great complex was closed, and the remnants of past glories were remediated after nearly a century of operation. This paper offers some insights from the real world affecting similar complexes still operating, and, hopefully, lessons for others just starting down the path to final closure.

Jan 1, 2003

By Shengli Wu, Yuandong Pei, Shaoguo Chen, Zhixing Zhao, Haijun Kang, Jiangshan Shi, Wen Pan, Zhengming Cheng, Yaosheng Luo

Grate bar is the key component of the sinter machine used for loading sinter and raw materials. Bar channels are sometimes bonded into blocks, which affects the service life of bar, and more importantly reduces the effective ventilation area of the sintering, affecting the normal production of sintering, resulting in unstable negative pressure, higher electricity consumption, and lower production and quality of sinter. In order to solve this problem, the systematic study was done on bonding materials of bars, based on which bonding mechanism of sinter grate bars was obtained. The KCl is an important characterization of bonding. Control standard of blending ore that prevents bonding is K2O content below 0.06% and Cl content below 0.05%.

Mar 1, 2018