Search Documents

By S. P. Marsh, D. Banerjee

"Casting processes involve phenomena that occur on widely disparate length-scales. Simulation of macroscopic effects, such as heat transfer and convection, are generally addressed by solving the appropriate equations in discretized form on a finite-element mesh. Microscopic phenomena are described by micromodels that may be empirical or analytical in form. Coupling of phenomena in these two regimes is a critical issue in predicting microstructure and defect formation resulting from macroscopic process conditions. A formalism has been developed for expressing micromodels in a consistent manner using stereological parameters to quantify the geometric characteristics of the developing microstructure. This approach provides a robust and physically consistent method for coupling local micromodels with the macroscopic fields. The macroscopic state variables at each node serve as global constraints on the micromodels that are applied to a local unit volume. An outline of an equiaxed solidification model based on this approach is presented, along with preliminary simulation results. Coupling of convection and enthalpy effects between the micro and macro regimes is also discussed. IntroductionThe primary goal of casting simulations is to improve the reliability of cast parts while minimizing cost and development time. Effective simulations can speed up the mold design process and reduce the likelihood of defective parts by refining a particular casting process on a computer, reducing the dependence on cost- and time-intensive prototype castings. The challenge in developing effective simulations stems from the need to address physical processes that occur over a wide range of length-scales, from microscopic (atomic) and mesoscopic (microstructural) scales to macroscopic distances comparable to the size of the casting itself. Overviews of the various thermophysical phenomena and computational factors that are important in solidification modeling are provided in the literature by Rappaz [1] and Tseng et al. [2].Macroscopically, the solidification process is largely governed by the rate of heat flow from the alloy through the mold wall. Another important effect that occurs on the scale of the casting size is convective flow of the melt, which is driven by density-variations in the melt. Macroscopic calculations employ finite-element or finite-difference methods to solve the sets of equations that govern these effects, and the spatial resolution is determined by the grid spacings used for the calculations. Typical spatial resolutions are on the order of 10-2 to 10-3"" meters. This represents a compromise between the resolution required to simulate the continuum transport processes accurately, and the computational time required to model the entire solidification and cooling process."

Jan 1, 1994

By A. J. Paul, K. O. Yu

"Today, foundries are moving towards the use of models and design tools to gain a competitive advantage in producing castings of high desired quality. This leads to a growing alliance between foundries, software developers and researchers seeking to model, visualize and understand the phenomena taking place during the casting process. In addition, there is a need to develop affordable techniques to produce parts in small lot sizes. This leads to the development of a Flexible Manufacturing System consisting of: (1) up-front computer-aided engineering; (2) computer integrated proto typing with solid freeform fabrication; and (3) fabrication of the actual mold and related equipment to cast the part.This paper discusses some of the developments that are taking place today in the areas of modeling the physical phenomena during the casting process as well as towards developing a Flexible Manufacturing System for producing cast parts. Areas that require most work involve prediction of defects and mechanical properties using simplified analyses. In addition, electronic data sharing for collaborative engineering between geographically dispersed team members is also discussed. Case studies are presented showing successes as well as failures.IntroductionCasting, one of the oldest forms of metalworking, has recently seen a flurry of developments in the area of solidification modeling. These developments have come about after the realization that, in order to stay competitive, foundries need to reduce their scrap rate and production costs, and increase casting quality. Even though this is not new knowledge for foundry engineers, the tools to help them achieve this goal are just being developed and put in place for use by foundries. Several state-of-the-art software packages are currently available to analyze the solidification behavior in complex shaped castings. These packages make use of several different approaches for solving the various problems associated with casting processes. The overall architecture of a comprehensive solidification modeling system is shown in Figure 1."

Jan 1, 1994

By D. H. Rubisov

The neural networks modelling approach is one of the most elegant black-box type methods to model industrial processes. In this paper, this approach is applied to model the performance of the CEZ zinc electrowinning plant. The model that was built was found to exhibit an excellent predictive ability for voltage and current density. The model was also used to investigate the sensitivity of the process to various key variables such as temperature, current density, zinc and sulphuric acid concentration, etc. Optimal regimes for zinc production were identified from the power consumption standpoint.

Jan 1, 1996

By Zhao Guangwen, Wu Tan, Qiuzhan Tian, Duan Shuzhen

"A thorough study of lost currents in bipolar cells has been made for the development of the great potential of bipolar cells in energy saving. A proper equivalent circuit for bipolar cells has been found, and mathematic methods for computing lost currents at all kinds of polarization have been developed.At linear polarization, the lost currents can be computed by solving either a tridiagonal matrix or an ordinary differential equation of second order. This kind of values can be used to evaluate the minimal lost currents at given conditions. At other kinds of polarization, the lost currents can be computed by the same methods as above if the necessary experiments of measuring the cell voltages of every electrolytic compartment have been made. This kind of values can be used to design bipolar cells at practical conditions.Extensive experiments have been made to evaluate the effects of electrode polarization, emf of galvanic cell for the formation of electrolyzed substance, gaseous products, geometric dimensions of electrolytic cells, special resistance of electrolyte used, and the total and ordinal number of electrolytic compartments on lost currents. It is the first time to make such a systematic research by experiments in the world. Experiments showed that theoretic models were in good agreement with measured data. Experiments also showed that D.C. energy consumption of 0.45 kwh/kg of Pb for lead electrolysis from molten chlorides could be achieved in a cell with 7 bipolar electrodes.IntroductionIt is very promising to apply bipolar electrolytic cells to electrolysis of aluminum, magnesium, lead, zinc and perchlorinates for their great potential of energy saving for example, bipolar cells had been used in the production of magnesium and saved more than 30% of energy, being one of the three main techniques of energy saving in the production of titanium sponge (1)."

Jan 1, 1988

By S. Malinov, J. J. McKeown, W. Sha, S. McShane

"A model is developed for prediction of fatigue stress life S-N diagrams for Ti-6Al-4V alloy at different conditions, using Artificial Neural Network (ANN). Different factors which have influence on the S-N diagram are involved as input parameters of the NN, namely microstructure, environment, texture, test/work temperature, surface treatment and stress amplitude. As the output the S-N fatigue diagram is simulated and plotted.The model is based on standard multilayer feedforward neural network. The NN is trained with a comprehensive data set collected from the literature, using Levenberg-Marquardt training algorithm in combination with Bayesian regularisation. A very good performance of the trained Neural Network is achieved. Good correspondence between ANN"" prediction and experimental S-N diagrams is observed. Using the model S-N diagrams for different conditions are predicted and analysed. Graphical User Interface is developed for use of the model. We believe that the model will be important for practical applications in solving various problems on fatigue behaviour of the titanium alloy.IntroductionTitanium and its alloys have an increasing range of applications due to their very good combination of mechanical properties, corrosion and erosion resistance. They are currently finding widespread applications in many industries due to their desirable and versatile properties. Most important among the alloys is Ti-6AI-4Y. Jet aircraft manufacturers are the principal 'consumers of Ti-6Al-4V and it is often specified for critical parts, the failure of which could result in the loss of an entire system. A generic class of Ti-6AI-4V has been developed over the past years and it has become the best understood of all the titanium alloys. The advantages of titanium alloys include: (i) low densities, giving very attractive strength to weight ratios allowing lighter and stronger structures; (ii) superior corrosion and erosion resistance in many environments; (iii) high temperature capability. Although the titanium materials are still considered as expensive materials, for many applications the cost of titanium alloys can be justified on the basis of their desirable properties."

Jan 1, 2001

By G. R. Waters

NMR360 is developing a suite of chloride-based metals extraction processes, with the first commercial operation scheduled for commissioning late in 2018. It is critical, therefore, that with the introduction of any new technology, that the circuits do not suffer from mechanical failures which will compromise the operation. Although chloride leaching is at atmospheric pressure and relatively low temperature, the main challenge is preventing corrosion, since the high proton activity makes even a small amount of acid behaves as though it were concentrated. An additional challenge in concentrated chloride circuits is the potential for solids precipitation. In this context, therefore, correct valve selection is crucial, and NMR360 has partnered with CGIS to ensure that the Severe Service Valves (SSVs) needed will perform over and above the definitions of the Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry. This paper outlines what the minimum requirements are for SSVs in chloride leaching applications, drawing on five decades of industry experience from one of Canada’s leading valve experts.

By T. Plikas, L. H. Gunnewiek, L. Oshinowo

"Electric furnace smelting is one of the principal unit operations for ferroalloy production, and increased process intensity, improved availability, minimal maintenance and a longer campaign life are common objectives for electric furnace operation in order to obtain favourable economics of production. Furnace designers have continued to develop innovative solutions, e.g., furnace cooling systems, that have allowed these objectives to be realised and CFD modelling plays a key role in the design process. Enhanced understanding of the energy transfer process in the furnace and the ability to develop, evaluate and optimize components of the crucible design to match process requirements are the key motivators for modelling.This paper provides an overview of recent applications of CFD to the design of electric furnaces. The aim is to illustrate what can be done, and identify areas where further work is needed in this field. Examples include furnace bath simulation, crucible cooling system design, taphole design, baking of Soderberg electrodes, off-gas systems, and fume control and building ventilation. It is argued that the trend is for numerical models to become more encompassing while at the same time more accessible, and therefore further improvements in furnace design will be realised with continued and well validated modelling efforts.IntroductionOne of the main processing steps in ferroalloy production is the smelting of ore in electric furnaces. The three-electrode, AC submerged arc furnace is most prevalent method for smelting in the industry, with shielded-arc and DC plasma arc furnaces achieving limited application (1,2). Commercial furnaces range in size from a few megawatts to more than eighty megawatts of supplied power, and operate with the objective of maximising the return on capital invested. Maximising productivity and energy efficiency are two pathways to achieving this objective, through process intensification, increased availability, minimal maintenance, and increased campaign life for the furnace and associated equipment. Concurrently, the need to reduce the environmental impact of metal production by controlling the emission of particulate emissions, greenhouse gases, and other harmful by-products must also be met."

Jan 1, 2004

By Michele L. Bustamante, Gabrielle Gaustad

In recent years, t h e future supply of tellurium has been called into question due to the anticipated rapidly increasing demand from thin film cadmium telluride photovoltaics. Since tellurium is produced as a byproduct of other extractive processes – principally, the electrolytic refining of primary copper sulfide ore – it is important to explore the dynamics of the parent metal extraction and processing – in this case copper – when attempting to answer this question. This research explores the changing landscape of global copper production; introducing system diagramming and the concept of byproduct intensity (BPI) to illustrate concerning downward trends in tellurium supply potential. Upon closer inspection, it is concluding that, while a likely contributor to these downward trends, the increased use of non- traditional copper production techniques alone are not responsible; other factors include market substitution and incomplete data reporting. Additionally, a review of literature on tellurium recovery processing reveals a promising outlook for future supplies; highlighting potential for improvements in yield, which allow producers to make better use of what is available, even in the face of suppressed BPI.

Jan 1, 2014

By C. J. Newman

Prior to 1995, the smelting process at the Kennecott Utah Copper Corporation (KUCC) smelter consisted of Noranda reactors and Pierce-Smith converters. In the consideration of expansion opportunities, the existing process did not lend itself to a program geared towards processing the total output of KUCC mining and milling operations. During 1989 and 1990, a number of smelting options were evaluated. The final selection was the Outokumpu flash smelting process, coupled with the new Kennecott-Outokumpu flash converting technology. Facilities were designed and installed to process 1:0 million tonnes per year of copper concentrate, with the ability to expand to 1.2 million tonnes per year. Following the shutdown of the smelter facility utilizing the Noranda technology in May 1995, the flash smelting, furnace commenced operation in June with the flash converting furnace startup following a few weeks later. The smelter has achieved design production targets and environmental goals. Current operating rates are at or above design rates for concentrate and matte processing. Emissions are lower than the permit levels and equate to less than 3.5 kg of SO2 per tonne of copper. This paper outlines the design, construction, startup and the first two years of operation of the modernized KUCC smelter.

Jan 1, 1998

By Demaerel. J. P.

Arsenic plays a major role during electroreflning of copper. Both the arsenic content in the anode and the arsenic concentration of the electrolyte have, in conjunction with other impurities such as lead, antimony, bismuth and oxygen, a direct influence on the quality of the cathode. The mechanisms are currently slime. inclusion and precipitation of insoluble compounds in the bulk of the electrolyte. Arsenic has also been reported to have a depassivating effect on the anode. An influence on the anode slime adhesion has also been found. A literature survey is given and these data are compared with and completed by our own results based on lab and pilot scale experiments as well as on Olen tank.house practice.

Jan 1, 1987

By Leiting Shen

The thermodynamics of tungsten ore decomposition in mineral acid and alkaline solutions were studied. The published thermodynamic data of tungsten minerals were collected and assessed. The Gibbs energies of CaWO4 (−1538.43 kJ/mol), FeWO4 (−1053.91 kJ/mol), MnWO4 (−1206.08 kJ/mol), H2WO4 (−1003.92 kJ/ mol), and Na2WO4 (−1455.58 kJ/mol, aq) at 25 °C were adopted in the calculation using HSC software. The results show that CaWO4 is decomposed more readily in Na2CO3 solution than in NaOH,while FeWO4 andMnWO4 aremore reactive inNaOH solutions. Froma thermodynamic point of view, tungsten ore decomposes easily in acid solutions despite most ΔGo T increasing slightly with temperature. Oxidizing Fe2+ to Fe3+ in acidic solutions facilitates decomposition of FeWO4, and the reaction of CaWO4 in H2SO4 solution occurs more easily than in other mineral acids, due to the formation of sparsely soluble CaSO4. The results fit well with the experimental data and industrial experience previously reported in the literature.

By A. Dutta, B. Devulapalli, A. Mukhopadhyay, E. W. Grald

"Computational Fluid Dynamics (CFO) has matured over the past two decades as an analysis tool for conducting virtual experiments with significant time and cost savings. It complements and reduces physical testing. CFO has penetrated the diverse materials industry in much the same way as Computer Aided Design (CAD) did more than a decade ago. As the basic numerical algorithms used in CFO have steadily improved, so have the reliability, consistency and user-friendliness improved significantly, too. Other recent trends have also contributed to the rapid growth and widespread adoption of CFO. In this presentation, CFO applications from several materials processing industries will be presented using case studies. Emphasis will be on metals, glass and semiconductor applications.IntroductionThe term materials processing covers a diverse array of industrial applications and products today. From the continuous casting of steel, to the deposition of semiconductor materials atom by atom, to the extrusion of molten polymers, materials processing applications span an incredible range of length scale, process times, pressures, temperatures and velocities. The properties of the materials themselves, in terms of density, viscosity, thermal conductivity, etc., can be complex functions of temperature, shear rate, chemical composition and time. And the processing equipment may be very complicated in geometric shape.Computational fluid dynamics (CFD), the technique of solving the governing equations of fluid motion and other related phenomena using a computer, has enjoyed widespread and rapid growth, which started in the aerospace and automotive industries. More recently, CFD has also been successfully applied to a great many materials processing problems, in spite of the challenges described in the previous paragraph. The reasons for the growing usage of CFD in materials processing are many. Using CFD to test design options and reduce the number of physical prototypes can decrease the time and cost associated with new product and process development. CFD gives insight and provides detailed predictions of operating conditions in lieu of difficult, intrusive and often expensive experimental methods. CFD can be used as an aid to scale-up processes from lab or pilot scale to full production. Troubleshooting the performance of existing equipment is often carried out with the help of CFD. Determining how an existing piece of process equipment will operate under new conditions, or with new input ,materials, is also a common task for CFD."

Jan 1, 2004

By Neng-Wen Yu, Shau-Jun Zhu, Ji-He Wei

The desulfurization process by powder injection and blowing in the RH refining of molten steel and its mechanism have been considered and analyzed. Based on the two-resistance mass transfer theory and the mass balance of sulfur in the system, a kinetic model for the process has been developed. The related parameters of the model, including the mass transfer coefficients and the effective amount of powder in the molten steel being treated for desulfurization, have been more reasonably determined. Modeling and predictions of the process of injecting and blowing the lime-based powder flux under assumed operating modes with the different initial contents of sulfur and amounts of powder injected and blown in a RH degasser of 300 t capacity have been carried out using the model. The relevant circulation rate of the liquid steel and the powder injection and blowing rate were taken to be 100 t/min and 150 kg/min, respectively. The initial contents of sulfur in the liquid steel to be treated and the amounts of powder injection and blowing were respectively assumed to be 0.007, 0.006, 0.005, 0.004, 0.003, 0.002 mass-% and 10, 8, 6, 5, 4, 3 kg/t-steel. The total treatment time for desulfurization under each mode was set up at 24 min, equivalent to eight circulation cycles of the liquid steel to be treated. The results indicated that the predictions made with this model are in good agreement with some data of the industrial experiments and practice. Injecting and blowing the lime-based powder flux with the composition of 85 mass-% lime (CaO) + 15 mass-% fluorspar (CaF2) of 3-5 kg/t-steel, it is possible to decrease the sulfur content in the molten steel to ultralow level below (5-10)x10·4 mass-% from (60-80)x 10·4 mass-%. The total treatment time needed will appropriately be 12-20 min. Intensifying the powder injection and blowing operation and increasing the circulation rate of the liquid steel may effectively' raise the rate of the process in RH refining. The model may be expected to offer some useful information and a reliable basis for determining the reasonable process parameters and help in optimizing the technology of desulfurization by powder injection and blowing in the RH refining of molten steel.

Jan 1, 2000

By A. C. Mollison

In November of 1983 a fire inside the autoclave caused the curtailment of operation of the Kidd Creek pressure leaching facility. Subsequent repairs and recommissioning of the autoclave in 1984 allowed Kidd Creek to increase its production of zinc as originally planned. This paper describes the operation of this process from 1984 to 1988 and details major mechanical work carried out on the vessel in 1.988:

Jan 1, 1990

By Michael J. Marinigh

"Increased safety requirements, higher operational costs, greater environmental restrictions, and new competitive processing techniques are the challenges smelter operators must confront in order to remain economically viable.In converting furnaces which have tuyères such as the Noranda Reactor and the Teniente, Peirce- Smith and Hoboken converters, efficient tuyère line management is critical to optimizing blowing rates, increasing refractory life, and improving safety.This paper will describe recent improvements made to equipment used for tuyère punching, tuyère silencing, tuyère pyrometry and refractory drilling of tuyères and how the proper application of the equipment can lead to operational and safety improvements."

Jan 1, 2009

By Qinmeng Wang

The oxygen bottom blown copper smelting process is a new technology which has been widely applied to the copper production in China. In this work, a computational thermodynamics model for this technology has been established, based on smelting mechanism and theory of Gibbs free energy minimization. The calculated results from the model agree well with the actual industrial data, indicating that the model can be used for the predictions under different operating conditions. The tendencies of the key parameters (such as Cu losses and Fe3O4 content in slag) and the distribution ratios of the minor elements (such as Pb, Zn, As, Sb and Bi) can be predicted by adjusting the oxygen/ore ratio charged into the bottom blown copper smelting furnace. The model can be used to monitor and optimize the industrial operations of the oxygen bottom blown copper smelting process.

By Ram V. Ramachandran

As an industry with major potential impacts (both good and bad) on water resources and due to the rising costs of process water, the mining and metallurgical processing industry has a key responsibility to contribute to the overall goal of preserving both the quantity and quality of water available within the watersheds they operate in. As we plan for new and existing mining and metallurgical projects, we need to consider a hierarchy of options to minimize our impact within the watersheds we operate; keeping clean water clean by diverting around our operations; reduction in the amount of water we use; reuse of water wherever possible, and improvements to water quality for recycling and/or release to environment. Technology is needed to treat water to improve its quality for reuse or release to the original watershed. While lime precipitation followed by sulfide polishing is effective for removal of most of the metals, it does little or nothing to remove ammonium ions and anions such as chloride, nitrate, molybdate, arsenate and selenite/selenite. Regulations on sulfate limits in treated discharge water has drawn close attention to the treatment of acid mine drainage (AMD). Management of brine and salt disposal is also posing a problem due to strict regulations and cost of disposal. This paper will: (a) address issues associated with managing water with the objective of maintaining water sheds—status quo-during and after operation (b) discuss potential technologies for advanced water treatment plants.

By Michael G. Mayer

Since its invention in 1859 various designs of lead batteries have evolved to meet commercial needs for traction applications and standby power. In recent years major developments have taken place in lead alloys and the chemistry and mechanical design of industrial lead batteries. These are reviewed in relation to their commercial application together with the new type of maintenance free gas re-combination lead-acid batteries which are opening so many new markets for lead.

Jan 1, 1990

By G. Sterzik, W. A. Jankola, T. L. Salway, D. J. McKay

At Trail, British Columbia, Cominco's zinc leaching and solution purification processes include direct pressure leaching of zinc concentrates, leaching of fume from the lead smelter, leaching of calcine and electrolyte purification. These processes have been adapted to match the unique characteristics of Cominco's integrated zinc and lead operations. Recent modifications include changes to the purification process and iron-residue handling circuits. In 1997, a new five-compartment autoclave, complete with ancillary equipment, was installed in the pressure leaching plant. This paper discusses these changes, the current flowsheet and further improvements.

Jan 1, 2000

By Gerald M. Rich

Magma Copper Company, a subsidiary of Newmont Mining Corporation, has initiated many changes in the continuous casting of 5/16 inch diameter copper rod since startup of the San Manuel rod plant in early 1972. With rod production at forty percent over design capacity, many production records have been established including a record cast of 761 tons of salable rod in a twenty-four hour period. The most challenging and rewarding introduction was the continued utilization of an alloyed copper casting wheel in lieu of the conventional steel wheel. With proper cooling and careful control of the mold release agents. as much as 58.000 tons of copper were cast on a single copper wheel. Other advantages are: 1) Fifteen percent increase in available casting time 2) Reject rod from steel inclusions was reduced by nearly one-hundred percent 3) Wheel cost was decreased by ninety-one percent 4) Natural gas consumption dropped approximately fifteen percent 5) Large increase in refractory component life 6) Reduction of manhours/ton. Many other modifications have contributed to excellent rod quality and high operating efficiency. A two-piece launder was replaced with a single castable launder which reduced oxygen pickup and provided better slag removal. Modifications to the bar preparation unit, pickling system, and coiler resulted in considerably higher milling efficiency.

Jan 1, 1976