Search Documents

By Takeshi Yoshikawa, Kazuki Morita, Kunitoshi Matsunaga

"In metallurgical grade silicon (MG-Si), most impurities mainly exist at the grain boundaries and distribute in silicon grains at extremely small contents. Grain boundary phases in MG-Si transform into liquid above the eutectic temperature, and migrate towards high temperature regions when heated under a temperature gradient. With the migration of all liquid phases in MG-Si to the surface, the impurity contents will be decreased less than their solubilities in principle.In the present work, the fundamental research was conducted to discuss the possibility for purification using the liquid phase migration technique. The purification limit was estimated by thermodynamic calculations, and metallic impurities were estimated to be effectively removed except for Fe and Al. The migration behavior of the liquid phase in the synthesized silicon substrate was investigated by unidirectional heating under infrared radiation at 1523-1548 K, and the proceeding of migration was confirmed. The migration velocity was 1.4--2.0xl0-7 mis, and found to be controlled by the liquid phase diffusion.IntroductionPhotovoltaic energy is one of promising energy resources in a sustainable society because of its inexhaustibility and cleanliness. Although the production and installation of solar cells have increased significantly during the last decade, the cost of solar cell installation is still high. To enable the widespread use of photovoltaics and for the photovoltaic electricity price to reach grid parity, a low-cost and abundant feedstock of solar grade silicon (SOG-Si) is essential. Recently, a modified Siemens process and a fluidized bed reactor process were developed to address the cost and energy issues associated with the conventional Siemens process. However, their cost reduction potential is limited because of the large energy consumption needed to convert silicon into gaseous compounds. Purification of silicon through metallurgical routes offers a promising way for producing SOG-Si from metallurgical grade silicon (MG-Si), because it enhances productivity and can also lower the process costs. Although several metallurgical processes such as directional solidification [l ], vacuum refining [2-4] and plasma oxidation [5-7], have been developed, processing times and refining efficiencies still have to be optimized."

Jan 1, 2013

By Tseng. B. H.

Samples of unchlorinated and chlorinated carbonaceous concentrate from a carbonaceous gold ore were analyzed by transmission electron microscopy (TEM) for organically bonded sulfur and chlorine. The concentrate assayed 1.53 oz/t gold and 6.01% organic carbon. Much of the organic carbon occurred as sizable coarse particles up to several hundred microns in size, which showed no visible evidence of reaction with chlorine after chlorination treatment. Both the untreated and chlorinated fractions of the carbonaceous concentrate were analyzed by the TEM method, which detected organically bonded sulfur in all of the carbon particles examined in the untreated sample, ranging from about 1 to 5% organic sulfur, and averaging near 3.1%. TEM analysis of 40 carbon particles in the chlorinated sample indicated that organic sulfur was reduced significantly in the carbon and replaced in part by the chlorine, as the result of chlorination.

Jan 1, 1987

By K. Krishnapisharody

A mathematical model has been developed to predict the interface dynamics and droplet generation of the buoyant phase in a two-fluid system. The model employs the well-known SIMPLE algorithm for obtaining flow fields and the Volume of Fluid (VOF) method, for interface tracking. The implementation of the model in water-oil systems, where the oil layer is placed above a recirculating water bath, is discussed. The evolution of the water-oil interface leading to the formation of oil droplets is computed realistically.

Jan 1, 2008

By Christine P. Viecelli

As Phelps Dodge Corporation addresses the environmental challenges of the 1990's, water management has become a key element in an overall waste minimization strategy. The Phelps Dodge Hidalgo copper smelter has implemented a comprehensive water management program that includes management of both fresh and process water utilized by its pyrometallurgical operation. Two major technological strategies are being implemented. They are the design, construction and operation of a raw water pre-treatment facility to allow increased evaporation within cooling towers thereby minimizing blow down, and the use of a brine concentrator to treat and recycle significant quantities of process water. The end result of this program is a significant reduction in raw water pumped from the underlying aquifer into the facility as well as a decrease in process water which must be impounded or otherwise treated.

Jan 1, 1992

By Samson Adeosun, Sanmbo Balogun, David Esezobor

"Iron and steel making processes give rise to large amounts of usable and unusable materials, the latter generally being termed wastes. It is sometimes difficult to distinguish between re-usable by-products and wastes which cannot be sold or land-filled. Much depends on circumstances such as the local market for the material. This can itself vary from time to time with by-products which cannot be used or sold becoming wastes and vice versa. This paper defines the concept of “waste-free technology”, discusses its development in the steel industry and highlights the benefits of the technology to the manufacturing sector and the environment. The paper also articulates how the “waste-free” technology could be applied in the proposed Ajaokuta integrated steel plant in Nigeria.IntroductionIn the past, nature was considered an inexhaustible store. Its resources were consequently exploited and waste products therefrom were discarded. Today, attitudes have not changed appreciably even as raw materials cost rise by the year to pose a series of socio-economic problems, which, among others, may include the rational and optimum utilization of resources, environmental protection and reduction of waste formation. Consequently, industrialists now face unexpected regulatory pressure in areas of pollution prevention, waste minimization and hazardous waste disposal.Iron and steel making processes give rise to significant amounts of usable and un-usable materials, the latter generally being termed waste. It is sometimes difficult to distinguish between re-usable by-products and wastes which cannot be sold or land-filled. Much depends on circumstances such as the local market for the material. This can itself vary from time to time with by-products which cannot be used or sold becoming wastes and vice versa. In this paper, the term waste refers to those materials that are either irrationally utilized or, land-filled and part of the byproducts that are not utilized. It includes that part of used materials which is not incorporated into the products manufactured during a process stage and which in contrast to reuseable materials, is considered not suitable for any further use, owing to technical or economic factors. In general, these materials are inorganic and parts of them are either utilized or passed to the other processes; the other part should be disposed of using well-established waste disposal practices to avoid any environmental threat.Thus, creative methods must be developed to modify the manufacturing processes to reduce emissions and process wastes by fully utilizing all resources. One method of eliminating the negative effect of waste formation is the use of purification and cleaning structures (pollution control system, PCS). These are, however, quite expensive."

Jan 1, 2008

By S. I. Sobol

Completeness of cobalt recovery from slag requires decomposition of maggemite and non - ferrous metal desorption with polymerized silicon-acid. Cobalt losses are reduced in leaching tai1s up to 200 g/t of iron.

Jan 1, 1993

By Merete Tangstad, Fei Li

This paper studies the quartz and carbon black pellets at elevated temperature with varying temperature and gas atmosphere. High-purity quartz and commercial ultra-pure carbon black was mixed (carbon content wt.15%), and then pelletized into particles of 1-3mm in diameter. The stoichiometric analysis of the pellet during heating is studied in thermogravimetric analysis (TGA) furnace at different temperature in CO and Ar atmosphere. The microstructure, phase changes and element content of sample before/after heating is characterized by X-ray diffraction, scanning electron microscope, X-ray fluorescence and LECO analyzer. The reaction process can be divided into two stages. Higher temperature and argon atmosphere are the positive parameters for SiC formation.

Jan 1, 2016

By Richard D. Hagni

Microscopic examination of selected, representative, unweathered samples of Birmingham, Alabama, Silurian, sedimentary iron ores has fully revealed the nature of the phosphorous-bearing mineral grains. The grains are composed of carbonate-fluorapatite (collophane), range in size from 1 um to 2.25 mm, and exhibit varied types of intergrowth with hematite. Modal analyses conducted under cathodolumi-nescence have provided quantitative data on the a3undance of each of 15 types of phosphorous-bearing mineral grains and made it possible to assess the potential phosphorous liberation from four types of iron ore. The results indicate that 27% of the total phosphorous contained in the iron ores in the western part of the Birmingham district can be expected to be liberated by fine grinding; 60% for ores in the eastern part of the district.

Jan 1, 1982

By P. Louis

Gécamines is the world largest cobalt producer with about 60 % of the Western World production. During the last ten years, its annual production varied from 5,400 to 14,600 t/year. The actual cobalt production capacity of Gécarnines is 18,000 t/year and could be increased in the near future if necessary. Cobalt is presently produced at the Shituru plant by an old in-pulp electrolysis process and in Luilu, by electrolysis of a clear weakly acidic solution. The Shituru Cobalt quality is lower than the Luilu one. For that reason, part of the Shituru Cobalt is fire refined and cast into granules. Large efforts have been succesfully accomplished to improve the cobalt quality. This has been made possible by a better knowledge of the purification processes and of the electrolysis parameters.

Jan 1, 1988

By Mark H. Hashiguchi

Examination of tensile bar surfaces shortly after destructive testing was conducted to search for clues that would aid in optimization of mechanical properties, especially tensile strength, yield strength and elongation to fracture. Cu-Ni-Si-Cr alloy bars in the as-cast, forged, rolled and extruded conditions were examined. Low ductility bars (<4% Elongation) showed dramatically different features than the fracture surfaces of high strength - high ductility bars (7 to 10% Elongation). Analysis of the fracture surfaces at 15X to 2000X and use of Energy-Dispersive X-Ray Spectroscopy (EDS) identified Ni-Si and Ni-Si-Cr precipitates of varying sizes and morphologies. Thermo-mechanical processing techniques to control the size and distribution of these precipitates show promise in improving the properties and performance of this alloy system and appear to correlate with improvements in the fracture surface morphology.

Jan 1, 2008

By W. G. Davenport

Flash smelting is used. mainly for making molten Cu-rich matte* from fine Cu-Fe-S** flotation concentrates. It blows dried concentrate particles into a hot fumace, surrounds them with 01-rich gas and allows them to react. The results are: (a) partial oxidation of Fe and S from the concentrate (b) generation of heat (c) melting of the oxidized particles to form molten Cu-rich matte, ~65% Cu and Cu-barren slag, ~1 % Cu. The melted particles fall to the hearth of the flash furnace where they fonn matte and slag layers, The matte is tapped from the furnace and oxidation-converted to metallic copper. The slag is skimmed, treated for Cu recovery then stockpiled or sold. Figures 1.1 and 1.2 show industrial flash furnaces and the position of flash smelting in the coppermaking flowsheet. ,Fig. 1.3 shows the locations of flash furnaces around the world.

Jan 1, 2001

By Billy W. Osborne

The use or primary dross as a source for aluminum ion in the manufacture of aluminum sulfate offers opportunities for an inexpensive raw material. The aluminum sulfate industry in the US is a mature market with numerous small plants operating close to major users. The majority of manufacturers use either bauxite or aluminum oxide trihydrate as a source for the alum¬inum ion.. However, using process technology developed and patented by IWC, the oxides are removed from primary dross for use in manufacturing aluminum sulfate prior to metal recovery. This process offers the benefit of reducing costs for metal recovery. This paper discusses some of the methodology used in this process.

Jan 1, 1995

By Reza Kamali, Mohsen Bashiri, Hadi Fanisalek

"Half of the input energy to aluminum reduction cell will be lost as waste heat which could be studied for possible recovery. Since price of energy is increasing and the main production cost in primary aluminum industry is energy, so waste heat recovery consideration will be interesting. One of the possible choices for recovering is from aluminum exhaust gases that needs minimum modifications for reduction cell and has no influence on cell heat balance which is vital for the operation. By using heat exchangers with in-line and staggered tube arrangements which placed before fume treatment plant (FTP) we will be able to recover enough amount of heat. The main challenging problem which is necessary to overcome will be the heat exchanger material and its design because of corrosive and dusty exhaust gases from potroom. In this paper, a desalination system with six effects of evaporator is proposed for producing distilled water by using recovered heat from hot exhaust gases. The calculated amount of produced distilled water is around 27,000 / in this specific suggested desalination plant. The suggested desalination plant is based on Hormozgan Aluminum Company data (Hormozal) in Bandar Abbas, Iran which is constructed by the Persian Gulf.IntroductionWaste heat losses arise both from equipment inefficiencies and from thermodynamic limitations on processes. The exact quantity of industrial waste heat is poorly quantified, but various studies have estimated that as much as 20 to 50% of industrial energy consumption is ultimately discharged as waste heat [1]. In order to achieve a final decision for establishing the waste heat recovery plant in any type of industry, a strong feasibility study is mandatory. Also, we need to remember that the possible amounts of energy and suggested process plant for recovery have to be investigated before starting any feasibility study. This kind of study which is important to be finished before moving to feasibility step is mainly a theoretical study, and was done for the Hormozgan Aluminum Company (Hormozal). In addition to the exhaust gases from the potroom, the exhaust gases from anode baking plant appear to have a better potential for waste heat recovery compared to potroom exhaust gases. The average temperature of exhaust gases from anode baking kiln is 120°C higher than the exhaust gases temperature in the potroom. This needs further investigation in a different study, because this study is just focusing on potroom exhaust gases."

Jan 1, 2011

By Napisporn Memongkol

Syntheses of Al-TiC-Al2O3 and Al-SiC-Al2O3 composites were obtained in situ by carbothermal reduction of mixtures of Al powder, TiO2 powder and activated carbon powders and Al powder, SiO2 powder and activated carbon powders. The reductions were carried out in a horizontal tube furnace under flow of inert gas. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The synthesized products were mixtures of aluminum reinforce with titanium carbide and alumina and aluminum reinforce with silicon carbide and alumina. The effect of the reaction temperature (1000 o C ? 1200 o C) and condition of precursors on the Al powder, TiO2 powder and activated carbon powders and Al powder, SiO2 powder and activated carbon powders were investigated using XRD and SEM method. The synthesized products showed those composites with aluminum matrix and titanium carbide and alumina as reinforced phases and aluminum matrix and silicon carbide and alumina as a reinforced phase was formed.

Jan 1, 2006

By Dao-Wu Yang, Ju-Lan Zeng, Li-Xian Sun, Yan Yao

"The hydration heat of the pure cement, the fly ash single-dopped cement, as well as the fly ash and fluorgypsum co-dopped cement were investigated by means of micro-calorimety with an eight-channel micro-calorimeter (TAM Air). The results showed that the hydration heat and the hydration rate could be reduced significantly by fly ash and fluorgypsum. However, the reduction was not proportional to the loading of dopant. The exothermic peak of the fly ash and fluorgypsum co-doped cement was appeared earlier than the fly ash single-doped cement. As the temperature decreased, the hydration heat and the hydration rate of the doped cement were reduced, and the exothermic peak appeared later. The effects of fly ash and fluorgypsum on the compressive strength of cement were also investigated. The results revealed that the early compressive strength of concrete made up of the co-doped cement was largely higher than that of the fly ash single-doped cement. Based on the experiment results obtained in this paper, we could conclude that fluorgypsum is a suitable additive for fly ash-doped cement.IntroductionFly ash and fluorgypsum are industrial waste. In 2008, nearly 400 million tons of fly ash has been produced by coal-burning power plants in China. And it is estimated that this number would exceed 500 million at the year of 2015. Besides, every year the fluoride salt factories in China discharge more than 100 million tons of fluorgypsum. Tremendous of fly ash and fluorgypsum occupy considerable land and contaminate air and water sources [1]. As a result, comprehensive utilization of this two industrial waste has draw great attention from all over the world.Cement is the most-used construction material on earth. But the production of cement consumes huge energy and destroys the environment. This problem might can be partly solved by applying fly ash and fluorgypsum as additive for cement [2-4]. During the last decade, some papers that focused on applying fly ash and fluorgypsum as additive for cement have been published [5, 6]. However, to the best of our knowledge, none of these papers investigated the hydration heat of the fly ash and fluorgypsum co-doped cement.The hydration of cement is an exothermic reaction, which can result in serious problem for mass concrete: The interior of the concrete could reach very high temperature as the hydration proceeded [7-9]. As a result, the great temperature difference between the interior and the outer of the concrete would exist and cause serious thermal stresses. Thus, the concrete would be destroyed by the cracks which in tum are resulted from the thermal stresses [10, 11]. The heat released by the cement hydration and the hydration rate is commonly regulated by adding mixed materials or transferring additive such as fly ash and fluorgypsum [12-14]."

Jan 1, 2011

By H. Forrest

Lead smelting at Cookson Industrial Materials was formerly carried out using a combination of Blast and Reverberatory Furnaces. In the late 70&apos; s these furnaces were replaced by two 20 tonne capacity Rotary Furnaces. This furnace type has proved to be more flexible in the range of feedstock that can be processed, including lead drosses, battery plate and even whole batteries. High rates of production have been achieved whilst attaining a good level of environmental control. The majority of the sulphur in the feedstock can be fixed by use of appropriate fluxes.

Jan 1, 1990

By S. Abe

Various copper anodes to be electrorefined were subjected to a heat treatment comprising annealing at a temperature in the range of 700 °c to 1,000 °c followed by a slow cooling preferably on the order of about 150 °c, and using these heat treated anodes , a series of dissolution experiments were conducted under conventional electrorefining conditions. The results obtained have indicated that the above annealing/slow cooling process dramatically improves the dissolution activity regardless of the type of anodes. As an example, passivation times of l to 3 minutes in a standard test have been increased to more than 80 minutes by this innovated heat treatment. Other advantages sterning from the improved anodic activity include reduced electrical short circuiting which results in substantial labor effort in the tankhouse, reduced energy requirement, and reduced cost of processing anode slimes because the amount of anode slimes is reduced. In addition, this process gives rise to a dramatic change in the nature of anode slime layer formed in such a way that a comparable final cathode copper product can be achieved even from high-impurity copper starting material.

Jan 1, 1987

By Alexandre Chagnes

The extraction properties of two synthesized cationic exchangers, i.e. bis (1,3-dibutoxypropan-2-yl) phosphoric acid (BiDiBoPP) and bis(1,3-diisobutoxypropan- 2-yl) phosphoric acid (IPA), have been studied for the liquid-liquid extraction of Co(II), Ni(II) and Mn(II) contained in 1 M HCl. A comparison of the extraction properties of these extractants diluted in kerosene with Cyanex® 272 shows BiDiBoPP and IPA extract advantageously at lower pH than Cyanex® 272 and a better Co(II)-Mn(II) separation is achieved using BiDiBoPP or IPA than with Cyanex® 272.

By Ricardo A. Valls

The Sechol Nickel-Cobalt Laterite Project is located in East-Central Guatemala, 140 km northeast from Guatemala City. In-situ resources in the immediate Sechol area, including those on other mining concessions contain 133 million tonnes of mineralization, grading 1.5 1% nickel. Considering the ever-increasing market for these metals, and the potential quick return on the initial investment, Jaguar Nickel Inc. is confident that by late 2006, it will be producing the first nickeltcobalt hydroxides from Guatemala. The path from now until the production stage passes through a pre-feasibility study, scheduled for completion by mid 2004, and bankable feasibility by mid 2005. Jaguar&apos;s objective, however, is not only to have a producing nickel-cobalt mine by late 2006, but also to continue with the exploration work in order to make Guatemala one of the world&apos;s leading nickel-cobalt producers. The Sechol group of deposits is conformed of several lateritic pockets, delimited by tectonic faults, and hosted by ultramafic rocks of the Sierra de Santa CW. ophiolitic belt that intruded the Maya Continental Block during the Early Tertiary age. The intrusive is mainly represented by a layered sequence of dunites, peridotites, and pyroxenites, usually strongly serpentinized. Existing data indicate that these rocks underwent fractional crystallization, and probably some degree of magma mixing and contamination previous to their main tectonic event. The most complete profiles are usually present over weathered dunites and serpentinites, while on top of the less altered pyroxenites, there is usually the formation of only a limonitic zone. The relative complexity of the ophiolitic belt explains the variety of mineral resources in the area, which include Ni-Co-Fe laterite, chromite, bauxite, magnesia, and also has the potential for gold, PGMs, and precious and semi-precious stones such as jade, nephrite, and chrysoprase. Metal recovery from the Sechol deposit will be based on an atmospheric chloride process, followed by solution purification, production of an intermediate nickellcobalt hydroxide suitable for sale, and finally acid and magnesia recovery by standard spray roasting technology. The chloride process will allow exploitation of the whole lateritic profile to produce 20,000 Mt of nickel hydroxide and 800 Mt of cobalt hydroxide per year. The exploration work completed to date has concentrated mostly on the Sechol group of deposits, representing less than 5% of the current land position of Jaguar in Guatemala. Within Sechol, the company has identified a large pocket of more than 5 Mt of laterites grading 2.1% nickel and 0.08 % cobalt as a startup pit "El Inicio". Including the work previously completed Keywords: Laterite deposits, Ophiolitic Belts, Central Guatemala, Nickel, Cobalt

Jan 1, 2004

By Emil H. Geus

A process has been developed to recover aluminum from dross which does not require the use of salt flux as commonly employed, This results in a salt-free residue which has potential industrial uses or alternatively can be safely land-filled. The dross is first heated by an air-fuel or oxy-fuel burner in a sealable rotary furnace. At a suitable temperature the burner is turned off and the temperature of the dross thereafter controlled by means of an atmosphere of oxidative and inert gases. When the free metal has agglomerated it is first discharged from the furnace, followed by the residues.

Jan 1, 1995