Search Documents

By Jhon Cuya

Titanium dioxide is the well-known catalyst for the photodecomposition of water in UV region and its nanoparticles show better performance than its bulk materials. Furthermore, partially sulfurized TiO2 is expected to be chemically stable and have an enhanced photocatalytic activity compared with TiO2. For this purpose, the sulfurization behavior ofTiO2 nanopartic1es was thermogravimetrically (TG) studied by a thermo-balance with a quartz spring using CS2. From the TG curve of TiO2 nanopartic1es, first, the weight decrease appeared down to around 8 wt% and then sulfurization reaction started at around 500°C at a heating rate of 1 C°/min. The weight increase curve showed a maximum of ca 30 wt% at around 750°?C and then gradually decreased to ca 12 wt% at 1000°C. This would be caused by the formation of TiS2 followed by the decomposition ofTiS2 to lower sulfides, such as Tit.0.8S2 and Ti3S4. From the comparison of the sulfurization of TiO2 nanoparticles with that of anatase, rutile and Ti(OH)4, it was found that TiO2 nanoparticles showed a similar behavior to that of Ti(OH)4.

Jan 1, 2003

By M. A. Aziz

The electrochemical performance of a series of carbon materials produced from coconut shells, which are very cheap and readily available in Bangladesh was investigated for their viability as anode materials in rechargeable lithium-ion batteries. X-ray diffraction technique was used to measure the interlayer spacing (d002) of the produced carbon materials. A number of half-cells were prepared with the produced carbon materials from coconut shell as working electrode and metallic lithium as counter electrode with 1MLiPF6 electrolyte in a mixture of ethylene carbonate and dimethyl carbonate. The discharge-charge profiles were measured for the different half-cells by using Arbin 24-channel Cyler. The value of interlayer spacing of the coconut-based carbon material was found to be 0.397 nm at 900°C, which is most suitable for lithium-ion insertion into the carbon structure without any expansion. The specific discharge capacity of carbon material from coconut shell heat treated to 900°C was found to be 1015.65 mAh/g. The coconut carbon material heat treated to 900°C delivered 335.22 mAh/g reversible capacity, which is comparable to the commercial carbon/graphite presently used in lithium-ion battery systems. The irreversible capacity loss and coulombic efficiency in 25th cycle of half-cell made with coconut carbon material were found to be 0.16% and 99.83% respectively. The carbon material produced from coconut shell can, therefore, be used as a potential anode for rechargeable lithium-ion batteries.

Jan 1, 2006

By Vinod K. Sikka, René Cooper

"Cohoes, New York 12047 Intermetallics are an attractive class of advanced materials. The aluminide intermetallics offer advantages including: (1) lower density, (2) oxidation resistance, (3) carburization resistance, and (4) interesting mechanical properties because of their ordered crystal structure. Even though the attractive properties of the aluminides and other intermetallics have been known for nearly four decades, their practical applications have not been developed for two reasons: (1) the poor ductility (in some cases, both ambient and high temperatures) and (2) the lack of processability into meaningful components. Recent advances such as ductilization of Ni3Al by small additions of boron and the knowledge that environmental effects are the major cause of poor ductility in Fe3Al and FeAl systems have brought the intelmetallics into the forefront of research and their commercial applications. This paper has described a method for melting Ni3AI-based alloys that successfully utilize the exotherrn for the formation of NiAl from the elemental materials. The reaction-synthesis method has also been utilized for the production of NiAI and NiAI-based alloy powders from the elemental powders. The reaction-synthesized powders of NiAI and NiAI-based alloys were consolidated by hot extrusion and evaluated for tensile properties over a temperature range from room temperature to 1050ºC. The powder-processing conditions have been found to have more influence on the ductile-to-brittle transition temperature of NiAI than the powder-production method.IntroductionIntermetallics are an attractive class of advanced materials [1-11]. The alum in ide interrnetallics offer advantages including: (1) lower density, (2) oxidation resistance, (3) carburization resistance, and (4) interesting mechanical properties because of their ordered crystal structure. Even though the attractive properties of the aluminides and other interrnetallics have been known for nearly four decades, their practical applications have not been developed for two reasons: (I) the poor ductility (in some cases, both ambient and high temperatures) and (2) the lack of processability into meaningful components. Recent advances such as ductilization of Ni3Al by small additions of boron and the knowledge that environmental effects are the major cause of poor ductility in Fe3Al and FeAl systems have brought the intermetallics into the forefront of research and their commercial applications. The paper will briefly review the processing techniques being pursued for the commercial applications of Ni3Al-based intermetallics. The major emphasis of the paper will deal with synthesis of Ni3Al and NiAI intelmetallics."

Jan 1, 1994

By Hannu Johto

Boliden Harjavalta has operated a flash smelter for nickel sulphide concentrates in Finland since late 1959. The original nickel flash smelting process was modified in 1995 to a novel nickel matte smelting (DON) with semi-low iron where the batchwise operated converting became obsolete. Since that, the process has been applied to multiple chemically variable nickel sulphide concentrates with high environmental performance. In this paper, the status of the current smelter operations is described together with the recent modernizations of the nickel flash smelting furnace and the slag cleaning furnaces.

By Neil Rowlands

Particle liberation studies are commonly used in the determination of the proportion of locked and liberated phases in ground ores at various stages of mineral processing. These studies may range from a qualitative assessment of a polished specimen in an optical microscope to a full quantitative analysis of the liberation characteristics of fine grained complex sulfide ores using scanning electron microscopy and high level image analysis. However, the conversion of quantitative data to meaningful information on a mill operations level is by no means a simple task. This paper reviews the errors inherent in the SEM/Image Analysis technique and looks at the various methods available to minimize errors in data collection.

Jan 1, 1992

By Tianyou Huang, Yuan Lu, Haimin Long, Jinwu Kang, Gang Nie

"The distortion of metal parts during heat treatment process is one of the main obstacles in industry to ensure high-quality work and less or no machining allowance, especially for large but thin steel castings such as heavy turbine blades. In the paper, a method is proposed to control the distortion by adjusting heat transfer coefficient of metal parts during heat treatment process. Required heat transfer coefficients can be realized by getting the metal parts into contact with various media such as water spray, insulation felt or materials with different heat conductivity. The control method based on this idea is set up and achieved. By using insulation felt and water spray to change the heat transfer coefficient during the stages of heat treatment process, the results indicate that the proper control time and vary with materials.IntroductionThe distortion of metal parts during heat treatment process is one of the main obstacles in industry to ensure high-quality work and to realize less or no machining allowance [1]. For example, the Three Gorges turbine blade’s distortion is as large as 50mm during heat treatment process. The uneven heating and cooling during heat treatment process is the main reason for distortion [2]. By adjusting heat transfer coefficient of different areas of metal parts, the heat treatment process could be controlled. The temperature variation, direct cause for distortion, could be under control. Loeser Klaus used high pressure gas to achieve uniform heat transfer during gas quenching and proposed the possibility to use ""Dynamic Quenching"" processes where the quenching severity is varied during quenching by stepwise control of either gas velocity or gas pressure [3]. Li Zhichao also suggested minimizing distortion by marking a component into several areas and imposing different heat transfer coefficients on each area [4]. Heat transfer coefficient can be controlled by getting the metal parts into contact with different media such as water spray, insulation felt, air or different heat conduction materials. In addition, the exact time to adjust the heat transfer coefficient is another factor for distortion. A method is presented in this paper by actively adjusting heat transfer coefficient for different areas of metal parts and different stages of heat treatment process to control their distortion. The corresponding experiments have been made by using different metal materials."

Jan 1, 2012

By Etsuro Shibata

The saturated solubility of chromium oxide and the valence of chromium in the slag are important matters when considering how to effectively utilize chromium-containing slags. The experimental data of various types of slags cited in the literature were arranged according to the optical basicity in order to evaluate the effects of the oxygen potential and the slag composition. The saturated solubility of chromium oxide and the Cr2+/ Cr3+ ratio tend to decrease with the increase of the optical basicity of the slag at an oxygen potential below 10.5 atm. However, at an oxygen potential of 0.21 atm, the saturated solubility and the Cr6+/Cr3+ ratio tend to increase with an increase of the optical basicity. A practical approach was suggested to reduce chromium in the stainless steel slag and simultaneously recover it as a ferroalloy by the direct smelting reduction of chromium oxide in the molten slag using some reductant in a small furnace.

Jan 1, 2003

By Feng Gao

A general unsteady- state model, based on a cracked substrate, has been developed to account for reaction and diffusion within porous substrate during oxidation of Carbon Fiber Reinforced Carbon matrix (CIC) composites. The effects of several parameters, such as diffusion and reaction rate ratio, oxygen concentration, and composite density, on oxidation process are explored. Also, theoretical results for a set of parameter values of the CIC composites are compared with experimental data. It shows that the model predicted values agreed well with the experimental data in weight loss. Based on this model, quantitative predictions of oxidation of a composite with cracked substrate can be made.

Jan 1, 1993

By Z. R. Llanos

This paper presents a review of industrial and experimental processes for the recovery of molybdenum, vanadium, nickel, cobalt and aluminum from spent hydrotreating or hydrodesulfurization catalysts. Numerous processes have been developed in a laboratory and pilot scale. However, worldwide, there are only four well established commercial facilities currently in operation. The installed capacity of these facilities exceeds the availability of spent catalysts and may be sufficient to assimilate future increases of spent catalysts. Despite liability risks; significant quantities of spent catalysts are still being landfilled. Changing regulations that may affect the future handling and disposal of spent catalysts are also reviewed.

Jan 1, 1995

By Tadafumi Adschiri

"Supercritical water can provide an unique reaction atmosphere for synthesizing metal oxide nanoparticles. Due to the drastic change of properties of water around the critical point, including density, dielectric constant and ionic product, the reaction phase with O 2 or H2 gas and the reaction rate and equilibrium can be varied to synthesize new materials or define particle morphologies. In this work, hydrothermal crystallization experiments are performed with several types of flow apparatus that allow convenient manipulation of variables such as temperature, pressure, and residence time. Key features in the flow modes and material preparation are discussed. The proposed supercritical hydrothermal synthesis method has the following desirable features: i) nanoparticles can be produced, ii) morphology of the produced particles can be controlled with small changes in pressure or temperature, and iii) a reducing or oxidizing atmosphere can be applied by introducing oxygen or hydrogen or other gases. An overview of this method is given for functional material synthesis of significant industrial interest including barium hexaferrite magnetic particles, YAO/Tb phosphor fine particles and lithium cobalt fine crystals.IntroductionHydrothermal crystallization, a method of metal oxide formation from metal salt solutions, is typically used at temperatures ranging from 373 K to 473 K. We are developing a new process for hydrothermal crystallizations that uses temperatures in the range of 673 K to 723 K, which is just above the critical temperature of water1 • 8 • In this work, we refer to this process as supercritical hydrothermal synthesis. The supercritical state of water allows one to vary reaction rate and reaction equilibrium by shifting the dielectric constant and solvent density with pressure and temperature. From of our research on material production in supercritical water, we have identified the following specific features of the supercritical hydrothermal synthesis method: (i) ultrafine particles can be produced, (ii) morphology of the produced particles can be controlled to some extent with pressure and/or temperature, and (iii) a homogeneous reducing or oxidizing atmospheres can be provided by introducing gases, such as O 2, H2, H2O 2• and so on.1"

Jan 1, 2000

By N. Menad

. Electronic wastes are heterogeneous mixture, with mainly copper, aluminium and steel attached to or mixed with various types of plastics and ceramics. In general, small amounts of precious metals are incorporated in this mixture. Today, these components constitute an environmentally problematic fraction in disposal. Their physico-chemical characteristics have been investigated through chemical, x-ray diffraction, infrared spectroscopy, scanning electron microscopy and thermal analysis.

Jan 1, 2000

By J. C. Huyhua

The effect or various oxidants on gold and silver dissolution in thiourea solutions (0.05 M in H2SO4) was studied using the rotating disc technique, a.t 2s c and 600 rpm. These studies were carried out at constant (4:1) initial molar ratio or thiourea to oxidant concentrations, to produce 50 % thiourea. oxidation. The initial dissolution rate of gold was approximately four times higher in the presence. of ferric sulfate (5.37 x 10-3mg cm-2 s-1) than in the presence of hydrogen peroxide (H2O2), potassium persultate (K2S2O3), or monopersulfa.te (KHS06). The dissolution rates for silver were considerably lower than gold for the same oxidants. Oxidation of thiourea in the presence of peroxygen and persulta.te compounds is a. fast reaction and it is completed in less than ten minutes. On the other hand, the oxidation or thiourea with? ferric.sulfate is slow, yielding a second-order reaction rate constant k = 6.09 I mol-1 h-1. Sulfur formation in the ferric thiourea system begins when ferric ion reduction approaches to completion. With hydrogen peroxide, sulfur is observed at lower thiourea concentration than ferric. Suifate. The presence of a large excess or free thiourea i.e., s to 20 % thiourea oxidation) retards sulfur formation and maintains favorable dissolution rates. Finally, carbon-in-leach experiments indicate that thiourea solutions a.re stable for several days, with ferric sulfate or hydrogen peroxide. The dissolution rates of gold and silver doubles in the presence or activated carbon when hydrogen peroxide is used as oxidant.

Jan 1, 1989

By A. M. Strachan

The application of submerged electric arc furnace smelting techniques to tin concentrates at the Capper Pass tin smelter in England is discussed. Some experimental data from earlier small scale 50 KVA electric smelting testwork on various low and medium grade tin concentrates is presented. Design considerations for the construction of a 3 MVA electric furnace to treat tin concentrates from the East Kemptville mine in Canada are considered, together with necessary precautions peculiar to the construction of a high grade smelter in close proximity to an existing low grade, complex non-ferrous metal smelting operation<. Slag composition modifications to optimise operational smelting conditions for various concentrates treated are discussed, together with refractory selection. The effect of concentrate impurity levels on the permissible degree of recycle to produce a satisfactory metal product is highlighted.

Jan 1, 1990

By Md. Z. Quadir, M. Ashraf, A. A. H. Ameri, J. P. Escobedo-Diaz

The quasi-static mechanical response of hot rolled lean duplex stainless steel 2101 (LDSS 2101) in rolling, transverse and normal directions under compression loading has been investigated for its perceived anisotropic behaviour. Microstructural characterization is performed by optical microscopy and Electron Back Scatter Diffraction (EBSD) to qualitatively define the influence of the texture by using Taylor factor and grain sizes, and phase boundaries by utilizing the modified Hall-Petch formula. It was observed that LDSS2101 does not show anisotropic behaviour in terms of the mechanical strength but it has a clear anisotropy in the lateral strains; the microstructural explanation of this response may result from the phase boundaries strengthening.

Mar 1, 2017

By Michael Sheedy

Sulfuric acid is widely used as an electrolyte for the electrorefming and electrowinning or metals. Impurities in this electrolyte are controlled by continuously bleeding solution from the tank house. In addition to the contaminant these bleed streams contain high levels of sulfuric acid and the metal being recovered. Subsequent treatment of these bleed streams often requires neutralization which generates large volumes of solid waste. Absorption resin technology employing a novel ion exchange technique known as Recoflo® allows the separation of the mineral acid from dissolved metal salts. The recovered acid is suitable for recycle back to the electrolyte circuit. The metal salt and other contaminants leave the process free .of the sulfuric acid. In this process, known commercially as the APU®, ion exchange resin is used to sorb sulfuric acid while excluding the metal salts. The purified acid is then removed by washing the resin with water. The process has been extensively used for the recovery of waste pickling acids in the steel industry and anodizing solutions in the aluminum industry. In the mining and metallurgical industries the process has been successfully evaluated for the separation of excess sulfuric acid from copper electrolytes, the removal of magnesium and manganese contaminants from zinc electrolytes, and nickel and copper from copper electrolytes. A full scale installation on a copper refinery bleed stream at Palconbridge's Kidd Creek plant in Timmins, Ontario has now been operating successfully for more than 1 year while pilot field trials have been successfully completed on other applications.

Jan 1, 1997

By H. Eccles

BNFL, an internationally acclaimed company noted for its nuclear fuel cycle services and waste management technologies, collaborated with Viridian BioProcessing Ltd, a small company acknowledged for developing environmental biological processes, and an internationally recognised professor of biological sciences, to develop an unique bioremediation process for treating toxic, heavy metal contaminated land. This paper describes the process, with particular reference to the problem and scope of land contamination with toxic, heavy metals and the current available technologies. The process technologies are based on using indigenous, soil micro-organisms which can be stimulated to produce acid or sulphide ions to mobilise or precipitate the heavy metals respectively. Laboratory studies have indicated metal removal efficiencies of greater than 90 % can be achieved, whilst recovery efficiencies from the metal loaded leachate are even higher at approximately 95%.

Jan 1, 1996

By Yuanbo Zhang, Zhixiong You, Zijian Su, Bingbing Liu, Guanghui Li, Guang Yang, Tao Jiang

Sodium stannate is widely used in the electroplating and tin alloy industry. But the traditional processes for sodium stannate production are characterized by long flowsheet, high production cost and strict requirement for the equipments, etc. In this study, a novel process for sodium stannate preparation from cassiterite concentrate and sodium carbonate via roasting in CO/CO2 mixed gas then followed by leaching was developed. The effects of roasting parameters on the Sn leaching efficiency were conducted. A Sn leaching efficiency of 77.2% was obtained under the optimal conditions. Sodium stannate (Na2SnO3·3H2O) with a purity of 95.8% was produced by the new process, which is better than that specified for the industrial first-grade product.

Jan 1, 2014

By Hiroki Kumakura, Kotaro Seki, Takashi Nagai, Masahito Abe, Daiki Noguchi

A large amount of platinum group metals (PGM) are used in automobile catalyst. It is important to recover the metals from wasted catalyst. PGM in the catalyst are supported by ceramics for four-wheel vehicle or metals such as stainless steel for two-wheel ones. The recycling process of PGM from the metal-supported catalyst has not been developed, while the process for ceramic-supported catalyst was developed, such as Rose process. We designed a noble recycling process of PGM from metal-supported catalyst using complex oxides between PbO and PGM oxide. In this study, complex oxides, PbPt2O4, PbPdO2, PbRh2O4 and so on were synthesized at about 773–973 K. And the dissolution behavior of these compounds to hydrochloric acid was investigated. PbPt2O4 and PbPdO2 were dissolved to hydrochloric acid easily, but PbRh2O4 was not.

Mar 1, 2017

By D. B. Dreisinger

The zinc pressure leach process developed by Sherritt Gordon, Ltd. permits the direct leaching of sulphide concentrates according to the overall reaction, ZnS +H,zS04 +402.+ZnS04+H20 +S0 The kinetics of the leach are affected by three rate controlling steps; ( l) oxygen mass transfer from the gas to the leach solution, (2) homogeneous oxidation of ferric ion to ferric ion by dissolved 011.ygen and (3) ferric ion leaching of zinc sulphide in the presence of a sulphur dispersing detergent (lignin sulphonic acid). Fundamental studies have been conducted to identify the factors that influence the kinetics of each individual rate controlling step. Oxygen mass transfer studies have been directed toward optimization of the agitator configuration for solids mixing and gas pumping from the atmosphere above the leach slurry. The rate of ferrous oxidation by molecular oxygen and the rate of zinc sulphide leaching by ferric ion have been studied over a wide range of temperature and solution compositions. The study of zinc sulphide leaching by ferric ion was supplemented by a series of interfacial tension measurements in the liquid sulphur - zinc sulphate solution system. The various kinetic studies have been summarized in terms of the importance of each rate to the performance of the process.

Jan 1, 1990

By D. H. H. Quon

Results of a study conducted to determine the properties of iron ore pellets made from Mount Wright and Carol Lake ore concentrate fines with partial and full substitution of bentonite by several organic binders are presented. Carboxy methyl celluloses 7H and 6TL, hydroxy ethyl cellulose (natrosol) and modified guar gum all produce pellets of acceptable wet, green and dry strength. However, when fully substituted, an inorganic binder such as calcium carbonate is required for satisfactory strength development after induration. Mixing the Carol Lake ore with Mount Wright ore in a 50-50 ratio also achieves the same result. The failure of the Carol Lake ore in the pelletization process is attributed to the low hematite content of the ore. The results are very similar to those from the extrusion studies reported earlier (8).

Jan 1, 1989