Search Documents

By Yang Xianwan, Zhu Xiaoyun, Guo Zhongcheng, Zheng Yanping, Zhai Dacheng

"Corrosion resistance of RE-Ni-W-P-SiC composite coating and 3 l6L stainless steel in corrosion media of H2SO4, HCl, H3PO4 and FeC13 solutions at different concentrations by means of immersion methods and anodic polarization curves obtained by DHZ-1 electrochemical synthetic tester and HDV-7 transistor constant potentiometer. Immersion experiment results show that corrosion rate of RE-Ni-W-P-SiC composite coating as-deposited in HCl solutions increases with the rise of HCl concentrations, on the contrary, the corrosion rate of the composite coating after heat treatment decreases with increasing the HCl concentrations the corrosion rates of the coatings as-deposited and after heat treatment in H2SO4 and H3PO4 solutions respectively decrease with the rise.of H2SO4 and H3PO4 concentrations the corrosion rate of the deposit as-deposited in FeC13 solutions decreases with increasing FeC13 concentrations, while the rate of the composite coating after heat treatment increases .with the rise of FeC13 concentrations.In addition, the corrosion rate of 3 l 6L stainless steel in the corrosion media of H2SO4, HCl, H3PO4 and FeC13 solutions at different concentrations increases with rising of concentrations. Furthermore, the corrosion rate of 316L stainless steel in the corrosion media of H2SO4, HCl, H3PO4 and FeC13 solutions respectively is much greater than that of the RE-Ni-W-P-SiC composite coating as-deposited and after heat treatment in the same corrosion media.1. IntroductionAll the materials and their products, when processed, stored and used, it is inevitable that the corrosion, wear, fatigue and crack occur owing to the actions of surroundings. Those early failure and abrasion, through all kinds of departments and profession that corrosion consumes one percent of tens of the steel products of the whole world; and two or four percent of the GDP is lost because of the corrosion."

Jan 1, 2000

By J. R. Bhamidipati, Nagy EI-Kaddah

"Over the years, mathematical modeling has been established as a viable tool for design and analysis of melting and solidification processes. Modeling of electromagnetic casting and melting systems involves three coupled problems -- determination of the containment field, the shape of the meniscus, and the temperature field -- which have to be solved simultaneously. One of the difficulties in numerical simulation of these systems is in defining and gridding the solution domain as the meniscus shape of the liquid region is not known a priori. This paper describes a methodology for solving these coupled problems in a two-dimensional electromagnetic containment field. This method is based on the solution of the electromagnetic, free surface dynamic, and heat transfer equations in a fixed domain in computational space by mapping the physical space into an invariant computational space during the search for the equilibrium shape using a variable non-orthogonal coordinate transformation. This approach, also, eliminates the need for regridding the liquid and solid regions during phase change. This methodology is demonstrated for two electromagnetic confinement systems -- the Magnetic Suspension Melting process and the electromagnetic casting of aluminum. The model predictions are in good agreement with available data for these systems. It is suggested that the methodology presented here is likely to provide a useful tool in the design, analysis, and optimization of electromagnetic confinement systems. IntroductionDuring the past decade, mathematical modeling has emerged as a viable tool for the design, analysis, and optimization of casting and melting processes /1-2/. It is generally recognized that the usefulness of modeling to study the interplay between the various process parameters without resorting to extensive experimentation relies heavily on accurate representation of the physical phenomena in these systems. In modeling electromagnetic confinement casting and melting systems, it is important that the model address all aspects of electromagnetic field interaction with the metal, if accurate predictions are to be obtained /3/. The electromagnetic field affects the heat transfer phenomena primarily through joule heating. In addition, the electromagnetic forces play a key role in heat redistribution in the molten pool via melt stirring, and, in confinement systems, support the molten metal pool."

Jan 1, 1994

By Peter Olubambi, Babatunde Obadele, Oluwagbenga Johnson

"The microstructure and corrosion behaviour of titanium carbide (TiC) reinforced duplex stainless steel matrix surface composites synthesized by laser melt injection technique was investigated. The surface melting operation was conducted using a 4.4 kW CW Nd:YAG laser with laser power of 1.5 kW, scanning speed of 0.4 to 1.0 m/min, beam size of 3 mm and argon shield gas flow rate of 4 L/min. The morphologies and microstructures of the coatings examined using field emission gun scanning electron microscope (FEGSEM) revealed homogeneous distribution of fine precipitates of TiC in the matrix, while X-ray diffraction (XRD) analysis confirm no phase change. TiC addition to the steels significantly increased hardness value to about 547 Hv0.1 but slightly decreased the corrosion resistance of the steels in 3.5% NaCl possibly due to the intergranular carbide coating that prevented chromium from forming continuous passive oxide layers.IntroductionComposite materials evolve from the idea of combining two basically dissimilar materials with different physical and mechanical properties to arrive at a product whose final properties are superior to those of the individual components [1]. Metal matrix composites (MMCs) are receiving much attention and are the focus of intense research and development worldwide for aerospace, automotive and other applications because of their excellent combination of ductility and toughness of the metallic matrix with high hardness and strength of carbides reinforced in the matrix [2]. Surface modification techniques such as laser, thermal spray, plasma spray, chemical vapour deposition have been use to fabricate MMCs. Laser melt injection (LMI) is a surface modification technique known since the 1980s [3] has been used to improve surface properties of metallic alloys such as aluminium, titanium and steels [4-6]. It involves the lateral injection of carbides, ceramics and cermets blown by a gas stream into a liquid metallic pool, created by laser irradiation of the top surface of the base material."

Jan 1, 2012

By M. A. Usman, E. I. Akpan, S. O. Adeosun

Preliminary studies on the extraction and characterisation of biodegradable lignin from palm oil fruitbunch (POFB) for carbon fibre production has been conducted. Centra lComposite Design was used to determine the optimum operating conditions for maximum yield and properties of the extracted lignin. Soda concentration (1–3 wt/vol%), temperature (50–90 °C) and reaction time (20–30 min) were analysed using Rcore software. Experimental results show that using reaction temperature of 90 °C, time of 30 min and 3 wt/vol% soda concentration yields 3.3 g of lignin from 30 g of the POFB. The path of steepest ascent from ridge analysis shows that with temperature of 130 °C, time of 40 min. and soda concentration of 3. wt/vol%, 8.7 g of lignin can be extracted from 30 g of POFB. Analysis of FTIR and SEM show that the lignin has the same structure in all cases with minimal impurities.

Mar 1, 2017

By J. M. Tourre

1995 have seen a continuation of a positive trend in the Rare Earth industry The availability of a greater diversity of Raw Material has brought additional flexibility to the Producers permitting better economics China remains the major raw material source; Chinese concentrate producers have increased capacity in 1995 (Baotou, Sichuan, etc) China's role in the Rare Earth industry will continue to evolve; the acquisition of a majority equity position by San Huan/CNNC will have a significant impact on both the Rare Earth and Magnet markets Chinese producers are increasing the quality of their products and realize their true values Chinese market, itself, is also changing as the internal needs for separated rare earth's grow Already already producer of Lamps, Loudspeakers, Magnets, and TV tubes, China is in an unique position where the potential of its internal market might be more promising than the prospects outside China 1995 has also seen the application market become more diverse and complex. There are new applications growing at a very strong pace (such as battery alloy), applications that are now penetrating their target markets with significantly increased growth rates (such as bonded NdFeB), and some applications that became more complex requiring much more sophisticated products (such as catalysis). Rare Earth producers have to spend significant ressources in order to monitor the market trends in order to predict the demand and then adjust their raw material mix. Even though there is a greater diversity of raw material available, there is still some Rare Earth elements that are in excess, while other are just in balance. As a consequence rare earth producers invest heavily in R&D in order to develop new applications for these excess elements.

Jan 1, 1997

By R. C. Hubli

Copper (II) chloride has proven to be an efficient lixiviant for copper sulphide ores and secondary sources of copper such as scrap. Nickel sulphides are generally associated with copper ores and copper-nickel matte is an intermediate product of processing mixed sulphides. While the copper species in aqueous chloride media are present as chlorocomplexes, the presence of nickel as Ni++ offers effective separation between the two by solvent extraction techniques. Oxidation of millerite by cupric chloride in sodium chloride solutions has been studied as a function of rate of agitation, leaching time, temperature, acid concentration and total initial cupric concentration. The reaction has a 1/2 order of dependence on initial cupric concentration in the range of 0.0 to 0.5M. The activation energy for the temperature range 333 -363 K has been found to be 59.2 kJ/mol with chemical reaction at the unreacted mineral surface as the rate controlling step. The rate expression, according to the shrinking-core model, for initial cupric concentrations between 0.0 to O.5M, is evaluated as

Jan 1, 1996

By C. A. Pickles

Microwave processing is a relatively new technology that has been successfully applied in a number of industries. However, in the field of metal extraction, there is a paucity of success, despite considerable hype in the early years. Increased reaction rates, lowered reaction temperatures and higher energy efficiencies were some of the advantages claimed. Even with over almost two decades of research and some pilot plant studies, microwave metal extraction remains essentially a laboratory technique. In this paper, the research performed over the last few decades will be reviewed and some reasons for the lack of success in developing microwave metal extraction processes will be discussed. Based on the knowledge gained from these experiences, a more informed view of microwave heating can lead to the realization that there is still some untapped potential for this heating technique in metal extraction processes.

By Saad Elias Kaskah

"The Box-Behnken Design (BBD) is used to model the sacrificial Cathodic Protection System (SCPS) to find the factors effectiveness behaviour. For protection potential assessment the BBD receives (resistivity of environment, sacrificial anode alloy, distance between anode and cathode and surface area for the structure to be protected) as input and gives the protection potential as output. By applying BBD with their analysis tools we get many results. The important results which are the factors individual effectiveness on the sacrificial cathodic protection (SCP) process are the resistivity which has the greatest effect on the potential protection (rank=l) followed by sacrificial anode alloy type (rank=2), surface area for structure protected required (rank=3) and distance between anode and cathode (rank=4). The interaction of sacrificial anode alloy and cathode area {X2X4 ) has significant effect on CP process with the limits which are used in this work while the other factors interaction (X1X2, X1X3, X1X4,X2X3, X3X4 ) has insignificant effect on the limits which used in this work.IntroductionFor carbon steel in seawater the normal corrosion potential E '°""_is in the range -550 to -600 mV vs. Ag/AgCI [1]. The most effective method to overcome the corrosion is cathodic protection {CP) which represents a control method in the steel wall corrosion. Cathodic protection has been used in several areas including marine and underground structures, storage tanks, and pipelines [2]. Sacrificial anodes system generates protective current which depends upon the inherent potential difference between the anodes and the structure to be protected. If the structure is made of iron or steel, any metal that is more active in the electromotive force series can theoretically be used as anode material [3]. There are many factors influencing on cathodic protection like resistivity (NaCl content), chemical composition of sacrificial anode alloy, distance between anode and cathode, surface area of cathode, temperature, humidity, velocity of solution, dust, impurities, bacteria and etc .. The present work studied four factors: NaCl content, resistivity), chemical composition of sacrificial anode alloy, distance between anode and cathode, surface area of cathode) with different three levels of values for each one. Then this work will find the optimum value from the factors levels that tacked to investigated there influencing on sacrificial cathodic protection system."

Jan 1, 2013

By Mingsheng He, Yunhui Tang

The structure and granularity of biological origin aragonite from abalone shell during wet grinding in a ball mill were studied with X-ray diffractometer, with morphology studied by scanning electron microscope (SEM). It is shown from the results that the particle sizes of aragonite decreased with grinding time, so did the X-ray diffraction (XRD) peak intensities, while the full widths at half maximum increased. A calcite XRD peak with low intensity and great width was observed in nearly all the samples with various grinding time, whereas the intensity of the peak increased obviously after grinding time 300 min. It is shown from the SEM results that the size of aragonite dropped with grinding time until it reached 20 nm and then kept constant, while that of calcite dropped first and then rose at the minimum about 10 nm until to the constant size as in aragonite. It was observed that the mineral content obtained from XRD show an obviously change that the calcite increases while aragonite decreases, which indicated the occurring of a polymorphic transformation of aragonite into calcite.

Mar 1, 2017

By John J. Mortvedt

Application of some by-products of the metals industry which contain plant nutrients to agricultural lands could constitute resource recovery instead of costly disposal. Some industrial by-products contain appreciable concentrations of heavy metal contaminants, such as Cd, Cr, Ni, and Pb. After land application, these metals may be absorbed by plants and enter the human food chain or be leached to groundwaters. Plant uptake of these heavy metals varies with plant species:, soil pH, soil texture, and the particular metal. Certain leafy vegetables can absorb significant amounts of heavy metals, while absorbed metals are usually poorly translocated to cereal grains. Allowable heavy metal concentrations in fertilizers now are not regulated, but EPA is considering such regulations. Heavy metal impurities in animal feed supplements are regulated by the states; so some by-products may not be permitted for this use.

Jan 1, 1992

By C. J. Beyke

Slags and/or mattes from three secondary lead producers were studied as part of an effort to develop treatment methods for these lead-bearing residues. Each company used a somewhat different production process. Company A used a reverberatory furnace followed by a blast furnace. Company B used only a blast furnace. Company C used both a reverberatory and a blast furnace, and the scrap material was desulfurized with sodium carbonate prior to smelting. The slag matrix produced from sulfur-bearing scrap consisted mainly of iron-calcium silicates; the slag from desulfurized material was similar, but also contained sodium. In all the slags most lead was present in metallic form, often alloyed with tin, antimony, arsenic, and/or iron. Slag from Company B contained the most alloying elements, often as discrete subparticles within the lead droplets. Mattes were produced at Companies A and B; predominant phases were pyrrhotite and magnetite, while lead was present in metallic form and as galena.

Jan 1, 1995

By William Petruk

The primary requisite for a successful extractive metallurgy operation is to grind an ore fine enough to liberate the minerals so that they can be concentrated, or to expose mineral surfaces so that the minerals can be leached. The ease or difficulty of liberating or exposing the mineral grains is dependent upon the mineral textures such as grain size, crystallinity and bonding between mineral grains. In particular, mineral grains with straight grain boundaries and a weak bonding to other minerals are easily liberated and readily concentrated into high grade concentrates. In contrast mineral grains that have re-entrant boundaries and are strongly bonded to their neighbours are not easily liberated and will not produce high grade concentrates, even with regrinding. Similarly, inclusions that occur along fractures and grain boundaries can be readily exposed and leached. Whereas minute random inclusions in large grains will not be liberated or exposed unless they occur along planes of weakness.

Jan 1, 1995

By P. K. Jha, M. M. Mahapatra, H. K. Mohanty, Pradeep Kumar

"During friction stir welding, the tool geometries affect the weld together with the process parameters like welding speed, vertical pressure and tool rotational speed. The present investigation deals with the three dimensional computational fluid dynamics modeling of friction stir welding process considering material flow around the tool, welding speed with respect to tool geometries. Friction stir welding tools with different tool geometries were used for the experiments to achieve acceptable aluminum welds. The temperatures near the welds for each tool were experimentally observed. A 3-D computational fluid dynamics (CFD) model was developed. Temperature-dependent material properties of the aluminum alloy were used in the CFD model. Thermal analysis was carried out considering rotational speed, vertical pressure and traverse speed for the tool geometries. The numerically predicted stirring patterns and temperature profiles closely matched with the experimental ones. IntroductionThe friction stir welding (FSW) is a solid state welding process where generally the metallic materials are joined by the combined action of frictional heating and weld zone stirring by a rotating tool [1]. The heat generated in the process is much below the requirement of melting the plates; hence the FSW process is devoid of harmful effects those are observed during arc welding. The FSW process utilizes a tool which has a shoulder and a protruding pin known as the probe. The shoulder is responsible for frictional heating while the pin probe facilitates stirring of the joint material. A schematic of FSW process is shown in Fig. 1."

Jan 1, 2012

By Ari I. Kogut

Impurity minerals in fluorspar ores and concentrates from a deposit in Southern Africa have been studied by reflected light, transmitted light, and cathodoluminescence microscopy. The principal impurities are quartz, calcite, aegirine, apatite, ankerite, magnetite, goethite, and synchysite [Ca(La,Ce,Nd)(C03l2Fj. Cathodoluminescence microscopy was found to be very useful in studying the character of the fluorite and especially for recognizing the presence of apatite and calcite impurities. Fluorite exhibits blue, calcite shows yellow, and apatite has white, light purple, and pink cathodoluminescence. The cathodoluminescent character of apatite varies with its geological environment and position in the orebody. The results of this microscopic study show that phosphorus present in flUorite concentrates occurs principally in binary locked apatite-fluorite particles. Successive fluorite cleaner concentrates contain progressively smaller amounts of locked apatite-fluorite particles. Free apatite has been effectively partitioned to the final tailings.

Jan 1, 1995

By Yongxiang Yang

High temperature processing of raw materials in metals production and recycling often involves complex multi-phase fluid flow and heterogeneous chemical reactions at various scales. Good understanding of the process physics and chemistry is crucial for process operation and process development. The traditional scale-up process through laboratory scale ? pilot scale ? commercial scale route has been more and more complemented and partially replaced by full-scale process simulation. Computational fluid dynamics (CFD) has become a very useful simulation tool in process research and development. At the same time industrial applications challenge the CFD development with its complex transport phenomena, often in large-scale reactors with small-scale physics and chemistry. The current paper discusses the applications of CFD to a number of high temperature metallurgical and materials processing applications. The research was carried out by using commercial CFD codes as the framework, and the emphasis was given to the special efforts for the development and implementations of sub-models with process-dependent physical and chemical characteristics. To illustrate the application of CFD simulation to high temperature metallurgical processes and coupling of sub-models to the general-purpose CFD codes, five examples are given: (1) melting of aluminium scrap in a rotary furnace for recycling, (2) molten hot metal flow in a heterogeneous coke-bed of a blast furnace hearth, (3) gas flow heat and mass transfer in a submerge electric arc furnace for phosphorus production, (4) high temperature incineration of hazardous waste in a rotary kiln, and (5) transient heating of metals in heat treatment furnaces.

Jan 1, 2006

By N. El-Kaddah, A. D. Patel, T. T. Natarajan

The phenomenon of particle migration in a conducting fluid under an applied electromagnetic force field finds its application in selective sorting of minerals and more recently in the removal of inclusion from molten metal. This paper deals with the analysis of the expulsion force and the flow around a spherical particle in crossed uniform electric and magnetic fields in .infinite and in confined medium. Analytical solutions will be presented for the electrk and magnetic fields as well as the induced flow at the limit of zero Hartmann number. The flow around the particle was investigated numerically at low and high values of Hartmann number. It will be shown the magnetic field has almost no effect on the velocity field when Hartmann number is less than 1.0. At higher Hartmann numbers the damping effect of the magnetic field was pronounced in the direction of the applied current. It is concluded that Hartmann number has little effect on the net force on the sphere particle.

Jan 1, 1999

By K. Osseo-Asare

"The molecular structural and solution chemical characteristics that underlie the surface activity of solvent extraction reagents are highlighted, with particular emphasis on the tendency towards reverse micelle and microemulsion formation. The physicochemical factors that lead to microemulsion-enhanced solvent extraction with chelating extractants are elucidated. Membrane-based contactor systems are described which are uniquely suited for enhanced solvent extraction with microemulsions. The possibility of combining solvent extraction with microemulsion-mediated materials synthesis is discussed. IntroductionThe discovery of new selective extractants has resulted in major breakthroughs which have helped to establish solvent extraction as a versatile separation technology (1-3). A complementary strategy towards new process development is to seek new ways of using the available reagents. This paper explores this second approach. From a molecular structural standpoint, an extractant may be viewed in terms of two components: a polar functional group and a hydrocarbon radical. In the conventional view of solvent extraction, this molecular structure serves two main purposes: The polar functional group provides the binding sites for complexation of metal ions, while the organic group is needed to render the resulting metal-extractant complex organic-soluble. But are these the only properties of the organic and the polar groups that are relevant to the solvent extraction process?In this paper, attention is directed to the fact that solvent extraction reagents possess the molecular structures of amphiphiIes; that is, they are characterized by the presence of spatially separated hydrophilic and hydrophobic groups on the same molecule. A case is made for the view that this amphiphilicity offers interesting opportunities to develop new separation processes which collectively may be described as enhanced solvent extraction (4-6)."

Jan 1, 1996

By Yogeshwar Sahai

Submerged gas injection into melts contained in furnaces, ladles, or similar transfer vessels is commonly used in industrial practice. In this review paper, conditions leading to gas bubble formation at the nozzle are first summarized. The increasing gas injection rates and other conditions, such as nozzle size, lead to regimes which are commonly known as "bubbling" and "jetting". These are explained. The gas/melt interactions result in energy transfer to the melt. In recent years, a large number of researchers have investigated the relationships between the energy density and the mixing times. Their work is reviewed, and the mixing mechanisms is described. Finally, computational approaches of modeling submerged gas injection are briefly presented.

Jan 1, 1993

By Jonathan M. Berkoe

Design engineers and metallurgists have long recognized the need for better methods to calculate a wide range of fluid dynamic effects in smelters and hydro- metallurgical facilities. Examples can range from the capture of fume in the secondary hoods of a copper converter, to controlling the thermal effects of heat transfer resulting from metal and slag flows within a furnace. With the advent of relatively low-cost, high- speed computers and user-friendly, commercially available computerized fluid dynamic (CFD) programs, these calculations can now be made. Use of CFD increased the understanding of both hot gas and molten flows in smelter facilities and has already led to design improvements in converter fume control hoods as well as improved management of heat transfer in electric furnaces. This paper will present two representative CFD applications to metals industry facilities. To date, Bechtel has implemented CFD results on four continents.

Jan 1, 1999

By J. W. Holzenthaler

Teams continue to play a major role at the Phelps Dodge Mining Company El Paso Operations, especially during the present time of low copper prices. The El Paso Operations' teams have taken the initiative during this copper market downturn and have helped reduce operating costs significantly. Because of this, Phelps Dodge El Paso Operations has continued to grow within the team process by creating a total, non- exempt salaried workforce. In the last year alone, the El Paso Operations have implemented three major initiatives to accommodate the team process. The first was the creation of "guiding principles", a policies and procedures handbook. Second was the "zero and beyond" safety initiative. Third was team compensation. In addition, the Copper Products Company has now adopted a work-team environment, following the lead of the refinery.

Jan 1, 1999