Search Documents

By E. S. Geskin

"This paper is concerned with the construction of a formal technique for the selection of a metallurgical technology. Exergy consumption is used as the criterion of process efficiency. Different items of the exergy balance are considered and techniques for the reduction of exergy consumption are determined. The selected techniques of exergy saving enable us to identify processes which should be used at different stages of steelmaking. The combination of the selected processes enables us to suggest a technology for conversion of iron ore into steel products. The selection of this technology narrows the range of further search of metallurgical processes. The paper shows that qualitative thermodynamic analysis can be used as the first step in the design of metallurgical processes. IntroductionThe existing processes for making, shaping and treating of steel enable us to convert the available iron bearing ores into marketable steel products. However, the energy cost of metal production is much higher than thermodynamically required, while the metal properties are much lower than thermodynamically available. Increasing cost and declining availability of energy and raw meterials make the creation of new steelmaking technologies imperative. In recent years, the number of novel processes for the making, refining, and shaping of steel have been suggested and tested. Some found a practical application. However, the tested technologies make up a small portion of the physically available routes for the conversion of iron ore into a marketable product. It is also not evident that the optimal routes have been tested and that the selected technologies are the best among those tested.Although the development of new metallurgical technologies must be based on the experimental and practical information, the number of the alternative routes for the making, shaping and treating of steel, as well as the cost of examining each single route, make necessary the use of analytical techniques for the evaluation of the possible ways of process development."

Jan 1, 1988

By M. R. Baren

Unpublished results obtained by Baren on thermodynamic properties of sulfur in liquid Fe. Co. Ni. Fe-Co. Fe-Ni. and Co-Ni are reevaluated. correlated. and interpreted on the basis of recent developments in thermodynamics of alloys:. Existing reliable data are reviewed and compared with the? present results. Sulfur obeys Henry's law up to 0.04 mol fraction. and in this range the standard Gibbs energy of solution of sulfur is expressed as a linear function of temperature for each pure metal. The activity coefficient of sulfur in each binary metal solvent 1s correlated with the composition of alloy.

Jan 1, 1983

By Joerg Hammerschmidt, Marcus Runkel, Andreas Wirtz, Kent Pope

"Fluidized bed reactor systems in the minerals industry have been progressively developed and widely implemented over a period of more than sixty years for a multitude of process applications. Their versatility is manifested in calcining, roasting and combustion treatment of minerals including solid fuels. Experiences from metallurgical processes have expanded to new applications in the oil shale processing, biomass combustion and renewable energy sector. This paper focuses on the most important aspects of fluidized bed technology for a variety of Outotec processes. Energy recovery is a major topic for all applications and will be addressed, as well as environmental aspects, particularly regarding the off-gas treatment. Outotec is one of the pioneers of roasting and the fluidized bed process including gas cleaning and sulphuric acid production where applicable. Process development is strongly supported by significant investment in R&D, thus enabling process adaptation and scale-up to meet specific customer/market requirements.Introduction to Fluidized Bed TechnologyThe early days of fluidized bed technology were characterized by the use of bubbling fluidized bed reactors (BFB). This technology was popular for roasting zinc and copper ores. The introduction of circulating fluidized bed technology led to increased plant capacities and improved process control for the traditional processes. Furthermore, the technology has been applied in many other industries, including the renewable energy industry, which will be part of this design and process comparison. The paper starts out with the fundamentals on particle fluidization as the main common design parameter, leading to the importance of heat recovery and offgas treatment.In fluidized reactor systems, the particle concentrations can reach several hundred kilograms per cubic meter of fluidization gas. This high solid concentration leads to large surface areas and enables direct contact of gas molecules with particle surface molecules. Excellent conditions for enhanced heat and mass transfer thus provide nearly ""ideal"" heat exchange conditions and better reaction kinetics. The bubbling bed exhibits a better heat transfer coefficient within the bed in comparison to the circulating fluidized bed (CFB). The different conditions of gas velocities and solid concentrations allowing the classification of fluidization reaction regimes are shown in the Reh diagram in Figure 1."

Jan 1, 2014

By John J. J. Chen, Barry J. Welch

"The production of primary aluminium can potentially lead to metal that, with minimum treatment, meets a high purity standard. Smelters that can achieve a significant proportion of their production in this manner have a competitive edge which is of growing importance as the use grows for such items as compact discs and the like. Superimposed on the desire to produce high quality metal are stringent environmental requirements that the industry must adhere to. The environmental legislation focuses on fluoride emissions and the approach adopted is towards a zero waste management philosophy. The fluoride recycling process does, however, result in volatile impurities being captured and recycled to the cell. Aluminium has an extremely high reduction potential and this results in a significant proportion of the recycled impurities being reduced at the electrolyte metal interface and thus contaminating the metal. This paper reviews sources of impurities and the impact of the operating procedures adopted on metal treatment.IntroductionSeveral factors have contributed to the immense growth in the aluminium smelting industry. Initially the ready availability of hydro electricity provided a primary reduction energy source for the production of the light-weight metal. Because of its unique properties and innovation in the industry there has been a continued exploitation of its unique properties, especially at the high purity end of the metal. The industry has shown considerably versatility and innovation in adapting to the ever increasing demands of quality and purity. It is however a competitive industry and the ability to produce high purity grade metal (>99.9% pure) gives a competitive edge. Emerging markets such as for CD ROM disc production etc, will keep the quality demand stringent.While the industry has met the continuing demands for metal quality, it has also had to respond to stringent environmental requirements for emissions from the production plant. Like all extractive metallurgical processes carbon dioxide is an inevitable reaction byproduct. However, the volatilization and hydrolysis of the solvent electrolyte leads to fluoride emissions that are potentially harmful. Accordingly, the industry has adopted essentially a zero non-process waste management approach. All cell emissions, including reducible impurities, are recycled back to the cell. This has had a significant influence on the metal treatment processes."

Jan 1, 1996

By Frank A. Stephens

The process of converting iron ore (principally Fe,03 or Fe30,) into iron carbide (Fe,C) to be used as feedstock for steel-making yields complex mixtures of several Fe-containing compounds as a function of processing conditions. In addition to the above compounds (hematite, magnetite and cementite), the mixtures typically contain wustite (FeO) and metallic iron(Fe). Mossbauer spectroscopy has been developed into aquantitative analytical method for monitoring the degree of conversion to carbide from samples periodically extracted from a fluidized bed reactor type of pilot plant. Calibration of absolute quantities of the above five compounds is based on standards prepared from known mixtures of the high purity individual phases. The PC-based spectrometer allows fitting of the well-known spectral components of each of the five phases, the resulting spectral areas then being compared with the calibration curves via PC software to yield the weight fraction of each. Emphasis has been placed on standardizing and simplifying the analysis procedure for routine use in an industrial environment.

Jan 1, 1993

By Robert R. Beebe

On the night of August 1'9-20, 1995, seepage was seen at the toe of the Omai tailings dam in Guyana. The mill was immediately shut down, and within two hours the flow, then mostly water, was diverted into an inactive mining pit nearby. At about the same time a second more serious break occurred at a point where water and solids could flow directly into the Omai River. By the time Ii coffer dam could be completed in the early morning of August 24, some 4.2 million cubic meters of tailings water and solids had escaped from the dam, of which nearly2.9 million cubic meters had reached the Omai River. This paper outlines some initial Process considerations and operational decisions which might have contributed to the dam's failure, describes how the Government of Guyana and the operator, Omai Gold Mines Limited, cooperated in dealing with immediate problems and shows how the Government set about investigating the accident. In particular, the paper details the work of a Process Review Committee comprising Guyanese and foreign experts convened to assess the gold processing and effluent management systems at Omai, and to recommend actions where appropriate.

Jan 1, 1998

By Sandra M. Stash

An integrated copper production complex includes mining, milling and smelting facilities which are usually at or near a common site, and sized to complement one another in capacity. There may also be an electrolytic retlnery serving the complex, but not always totally dedicated to its production. Mines and mills without co-owned smelters are not usually considered integrated. The first marketable product of an integrated complex is blister, or in some cases electrolytically refined copper. The nature of integrated operation brings together all of the environmental issues associated with copper production, but currently operating and newly planned facilities are required to anticipate these issues and meet stringent regulations. Older complexes, however, may have legacies of 50 or more years of operation unencumbered by current levels of environmental strictures: nevertheless, they must be remediated. Using examples from closure and remediation of the mining and mineral processing facilities in the Upper Clark Fork River Basin of Montana, the authors review some of the problems encountered since CERCLA's1 enactment in 1980, and the solutions to those problems, bearing in mind that not all of the problems and solutions were technical. Much has been written about the mines of Butte -the "Richest Hill on Earth" as it was known in its day and the mills, smelters and refineries they spawned. These facilities comprised an archetype of the integrated copper complex: from ore to metal in facilities serving and depending on one another. Many great stories of technological innovations and business triumphs have been told about Butte and Anaconda's mining history and the place The Anaconda Company occupies in that history. However, relatively little has been written about the final days: 25 years during which the once-great complex was closed, and the remnants of past glories were remediated after nearly a century of operation. This paper offers some insights from the real world affecting similar complexes still operating, and, hopefully, lessons for others just starting down the path to final closure.

Jan 1, 2003

By Edwin de Jesús Deveaux

After 32 years of operations beneficiating lateritic nickel ore in a fully integrated pyrometallurgical complex, Falconbridge Dominicana (FALCONDO), situated at Bonao and La Vega Provinces, Dominican Republic, has become profitable with one of the lowest nickel grade content processing plants in the world, and literally without any by-product (granulated slag, will be utilized in the future as a post-processing subproduct). To December 2002, mineral reserves were 64.1 million tonnes containing laterite grading as low as 1.15 % Ni when full dilution is applied. At a cut-off grade of 1.20% Ni, the reserves will provide 15-20 years of production. The mineralized thickness over the seven active deposits averages 6 m. Development of very selective and unique mining practices, together with improvements in the process plant, are key to achieving the production goal (30 kt Ni/yr) and to meet the quality standards for the ferronickel produced. Keywords: Laterites, grade control, mining methods, environment

Jan 1, 2004

Gas flow and heat transfer phenomena in two industrial-scale waste-heat boilers of the Outokumpu copper flash smelting process were analyzed with a commercial computational fluid-dynamics (CFD) package Phoenics. Various operating conditions were simulated for the first boiler and particularly for the second boiler. The gas flow pattern was compared qualitatively with the physical laboratory models, and the general flow pattern was consistent with the laboratory visualization. The heat transfer simulation was validated with, temperature measurements for both boilers, and good agreement was reached between the computed temperature profiles and the measured data. The computational results indicate that gas flow in both boilers is of three-dimensional and recirculating nature. The numerical tracer experiments indicate that some dead volume is present in both boilers, and the boiler modification reduced the dead volume from 38% to 15% under basic operating conditions. Radiative heat transfer accounts for 65-90% of the total 'heat transported in the radiation sections of both boilers under different operating conditions. The modified boiler is very efficient for cooling the off-gases at almost doubled volume flow rate. The CFD modeling proved to be a useful tool for numerical experiments and analysis of boiler performance for process: optimization.

Jan 1, 1998

By Rodney Clary

Building on work completed in earlier papers, the current paper presents a techno-economic evaluation of two recently demonstrated technologies for treatment of arsenic containing refractory gold concentrates. Using defined project parameters and inputs, the authors compare capital and operating cost estimates for pressure oxidation (POx), and the Albion Process™. The paper incorporates data now publicly available from the Albion Process™ plant, which has operated at the GeoProMining Gold (GPM Gold) project in Armenia since 2014, as well as recent POx circuits.

By Gang Qi

The solubility of nitrogen in pure molybdenum was measured over the temperature range 2173 to 2473 K and up to one atmosphere (101 kPa) of nitrogen gas pressure. Both thermochemical and kinetic aspects of this phenomenon were considered in this study. The solution of nitrogen in molybdenum may be expressed by the reaction 1/2N2(g) = {N} (Mo,s), for which the standard Gibbs energy is given by the expression {A}G° = 78,500 + 27.36T Joules/g atom N. The formation of molybdenum nitrides, specifically Mo2N, was considered. Attention was also focused on the mechanism of nitrogen solution in molybdenum. Estimates of the diffusivity of nitrogen atoms in solid molybdenum were derived from the kinetic data.

Jan 1, 1991

By Dean Ilievski

Mathematical modelling of the precipitation process requires that the kinetics of crystal growth, nucleation and agglomeration be known: This paper reviews the current state of knowledge on these precipitation sub-processes (ie. growth, nucleation and agglomeration) and describes a number of experimental techniques for estimating their kinetics. The experimental methods used to generate the precipitation data and the data analysis techniques used to extract the kinetics information from the data are discussed separately. There is no universal "best" technique for determining the kinetics. However, studies on multi-crystal systems are more reliable for modelling purposes than are single crystal studies. The selection of a technique will depend on which sub-processes are present. A problem with all kinetics studies is that there is generally a large uncertainty in the estimated kinetic parameters. This stems from the scatter in the experimental data being further propagated by the mathematical techniques used to extract the kinetic parameters.

Jan 1, 1996

By Ram V. Ramachandran

As an industry with major potential impacts (both good and bad) on water resources and due to the rising costs of process water, the mining and metallurgical processing industry has a key responsibility to contribute to the overall goal of preserving both the quantity and quality of water available within the watersheds they operate in. As we plan for new and existing mining and metallurgical projects, we need to consider a hierarchy of options to minimize our impact within the watersheds we operate; keeping clean water clean by diverting around our operations; reduction in the amount of water we use; reuse of water wherever possible, and improvements to water quality for recycling and/or release to environment. Technology is needed to treat water to improve its quality for reuse or release to the original watershed. While lime precipitation followed by sulfide polishing is effective for removal of most of the metals, it does little or nothing to remove ammonium ions and anions such as chloride, nitrate, molybdate, arsenate and selenite/selenite. Regulations on sulfate limits in treated discharge water has drawn close attention to the treatment of acid mine drainage (AMD). Management of brine and salt disposal is also posing a problem due to strict regulations and cost of disposal. This paper will: (a) address issues associated with managing water with the objective of maintaining water sheds—status quo-during and after operation (b) discuss potential technologies for advanced water treatment plants.

By M. Olper, M. Maccagni

"The crude zinc oxides (CZO) produced in any thennal process dealing with EAF dust also contain lead, cadmium, and a considerable amount of halides (chlorides and fluorides). The high halide contents make these crude zinc oxides less and less attractive, both technically and economically, and a further refining procedure is nece'ssary to meet the zinc and zinc oxide market requirements.Hydrometallurgical techniques commercially used to dehalogenate the crude zinc oxides are not effective enough to upgrade the crude zinc oxides to the required specification for their direct use in the traditional sulphuric electrolysis by primary zinc producers.The EZINEX® PROCESS has solved the problem of the halides contained in the crude zinc oxides. This process is the only proven technology electrowinning zinc from a chloridebased electrolyte in a conventional cell house. This paper discusses the process economics taking the data from feasibility studies of different size commercial plants."

Jan 1, 2000

By D. J. Adams

Cyanide heap leaching is the predominant technology used in processing low-grade gold ores. During closure ora heap leach operation, residual cyanide must be removed from the process and waste solutions, as well as the heap. Biological cyanide oxidation is a proven, economical technology for destroying cyanide in process and waste waters and spent heaps; The use of biological cyanide degradation eliminates the need for toxic or corrosive chemical oxidizers and has- been implemented at full scale at treatment costs usually <$0.50/1,000 gal. The Applied Biosciences biological cyanide destruction (BCND?) process has been demonstrated to effectively treat cyanide, concentrations up to 350 mg/L. Treated process solutions and wastewaters also contained other contaminants such as arsenic, copper, iron, silver. selenium, mercury, nitrate and zinc, much of which was removed in the cyanide degradation process. Under optimal conditions, microorganisms can rapidly oxidize free cyanide in some process solutions from over 250 mg/L down to 0.1 mg/L in 4 to 5 hr. Cyanide is degraded to ammonia and carbon dioxide, with 50%ofthe cyanide carbon liberated as C02. In general, carbon tank based bioreactors degrade cyanide at significantly higher rates than process or wastewater pond configured treatments, which usually degrade cyanide-more rapidly than in heap treatments. Investigation of cell-free enzyme preparations as an alternative to live microbial cyanide degradation shows promise. Advantages of enzymes over live microbes for cyanide degradation include: (I) the ability to tolerate and degrade higher cyanide concentrations (> I ;000 mg/L), (2) nutrients to support live microbial cells are not required, (3) the effects of other toxic contaminants, such as metals, found in mining waters-are eliminated and (4) the potential for greatly increased kinetics.

Jan 1, 1998

By D. M. Wyslouzil

The fundamentals of dissolving silver and silver minerals are discussed in the following sections: 1) Basic chemical reactions in the silver system 2) Leaching of pure silver minerals 3) Leaching of silver-bearing ores 4) Description of processes The basic chemical reactions of silver are an important guide to the mineral processor or the extractive metallurgist, particularly for systems in which complex formations are balanced against solubilities. The competition of other cations for free ligands can shift the equilibrium to the detriment of silver. Solubilities of pure silver minerals in specific solvents may not be a good indication of the solubility of silver minerals in ores. The abundance of silver minerals which usually appear in a typical ore precludes the selection of a single method that would result in the best extraction of silver from all minerals in the ore. Frequently, the recovery of silver from host minerals requires a destructive pretreatment such as intensive leaching, oxidation with or without elevated temperature and oxygen pressure, or roasting. The transformation of the host or the silver minerals does not always result in a leachable species? and this requires additional treatment before the precious metal can be recovered.

Jan 1, 1990

By James P. Bennett

EAF slag chemistry and its control have been recognized as important in producing quality steel at a low price for a number of decades_ EAF steel producers make lime and dolomite additions to furnaces, controlling the CIS ratios and sulfur pickup from the steel. Existing phase diagram data at 1600°C for CaO, MgO, FeO, SiO2, and Al2O3 was used to write a computer model optimizing slag chemistry for slag foaming and reduced refractory wear. The model, its development, and its use in an industrial steelmaking environment will be discussed along with how the model can improve energy efficiency. The importance of EAF mass balance to account for critical materials like Si in scrap and refractory wear using the model will also be emphasized_

Jan 1, 2003

By Malti Goel

"Ferrous and non-ferrous metals industries are source of both direct and indirect greenhouse gas (GHG) emissions. Metal industry accounted for 29.7% of the total GHG emitted from the Indian industry sector in 2007. Aluminum is second largest contributor after steel. Indian Aluminum industry has been growing and is adopting several effective measures for better efficiencies through process change and waste utilization. Improvement in the energy efficiency can form the basis of monitoring reduction in emissions. Under the National Action Plan on Climate Change 2008, National Mission for Enhanced Energy Efficiency (NMEEE) aims to upscale the efforts to unlock the market for energy efficiency improvement on a public private partnership (PPP) basis. For a transition to low carbon economy industry is undertaking voluntary measures through scientific and technological innovations both in upstream and downstream sectors. In this paper an attempt is made to overview recent developments in Indian Aluminum industry as well as summarize scientific & technological challenges and prospects.IntroductionAluminum plays a vital role in industrial development. It is a substitute for different type of materials ranging from wood to copper and steel. The aluminum industry has high energy consumption and high contribution to greenhouse gases from carbon dioxide and perfluorocarbons (PFCs) emissions. It is estimated that CO2 equivalent burden of aluminum industry is about 1% of total anthropogenic emissions. The anticipated world growth rate is 3.5% for aluminum demand. Through measures to reduce both direct and indirect CO2 emissions, electricity consumption was reduced from 25 kWh / kg of Aluminum in 1998 to 15 kWh / kg of Aluminum produced in 2008. It is targeted to further reduce it to 10.8 kWh. Aluminum industry is also responsible to about 60% of all PFC emissions. The PFC emissions are harmful to environment, accumulate in surrounding vegetation and contaminate. Efforts to reduce PFC emissions from aluminum industry started early and reduced to 0.5-1 kg / tonne in 1990 [1] from 12-15 kg / tonne in 1940. Since 1990s to 2000 it further reduced to 0.2 -0.4 kg / tonne as seen in Fig. 1. The Global Aluminum Sustainable Development Initiative (GADSI), targets perfluorocarbon (PFC) specific emissions reduction of 80% for 2010 relative to 1990."

Jan 1, 2011

By John L. Sundstrom

Complete systems were designed -and are in operation to recycle the effluent streams and to remove impurities from tankhouse. electrolyte, Heavy em¬phasis was placed on making usable products from as many streams as poss¬ible at minimum capital and operating costs. Almost complete recycling: and reuse of water and sulfuric acid were paramount. Techniques used in-clude solvent extraction - electrowinning, evaporation - crystallization and filtration.

Jan 1, 1992

By Yutaka Shiraishi

Two methods were developed to measure the viscosity of the slag from the glassy to the liquid states in an ascending temperature process. The first method employs rotating parallel plates within which is placed a solid cylindrical sample in line with a sphere. The second method uses a tube which is pushed into a sample held in a rotating crucible. Both methods were tested using standard glasses, including boron trioxide and NBS standard glass #711. The main difference between these two methods is in sample preparation. Comparative measurements between two methods were performed using a sodium boro-disilicate glass containing 5%mol of alumina. The results showed good agreement in the mid-range of glassy viscosities, 105 to to7 Pa.s. In the liquid state, there were no significant differences between the two methods.

Jan 1, 2003