Search Documents

By Gopalakrishna B. Prabhu, David L. Bourell

"Three mol% Yttria-Stabilized Tetragonal Zirconia (YSTZ) was prepared by a sol-gel synthesis technique using zirconium tetrachloride and hydrated yttrium chloride precursors. After drying and annealing at 823K, the particle size was in the range 10 to 20 nm. The zirconia powder was sintered using a uniaxial hot press at an applied stress of 20 to 40 MPa. One hour, isothermal sintering was performed in air after initial heating at 50K/min. Theoretical density was obtained at densification temperatures above 1498K. After sintering, grain coarsening characteristics were studied using constant heating rate anneals followed by quenching, based on a model for grain coarsening in a linear heating rate cycle. The microstructural change was studied using SEM and TEM and the phases were determined using x-ray diffraction.IntroductionThe ability to sinter nanocrystalline materials to full density several hundred degrees below the normal sintering temperatures is one reason for their current interest. [1-5] Yttria Stabilized Tetragonal Zirconia (YSTZ) of grain size of about 300 nm has exhibited superplasticity, with elongations as large as 800%.[6-7] Fine grain size is critical for superplasticity. Retention of the fine grain size during sintering of nanocrystalline powder is important if a material is to exhibit superplasticity or to exhibit physical or mechanical properties associated with the ultra fine structure. This paper investigates the sintering behavior and the grain coarsening characteristics ofnanocrystalline YSTZ.Techniques for synthesizing nanocrystalline materials have been studied in great detail earlier. [8-12] The techniques used to synthesize nanocrystalline zirconia include alkoxide synthesis [9], the chloride method [11], the peroxide method [13] and the acetone-toluene method. [13] In this paper the method used in the synthesis of zirconia is the chloride technique. With this precipitation technique, either zirconium chloride or oxychloride and a corresponding yttrium salt or even pure yttria are used."

Jan 1, 1994

By W. G. Davenport

This chapter demonstrates how our matrices can be used for controlling a flash furnace. Specifically, it shows how we can determine the adjustments in industrial oxygen, air, oil and flux input rates that will; (a) correctly alter product temperatures and compositions to newly targeted values (b), maintain set-point product temperatures and compositions with varying feed compositions and feed rates. It also discusses corrective actions that might be taken when furnace temperature and matte grade unexpectedly change.

Jan 1, 2001

By Zhang Chuanfu, Li Shixiong

"In the electrolysis electrodeposition or electroplating of aqueous solution of copper, lead, zinc, nickel, manganese etc, with the increase in cathodic over potential the reducing rate of metal and the cathodic current efficiency increases and the deposit becomes more compact and smooth. According to this principle, a method and equipment of the auto-control of electrolyte quality is invented. The industrial application shows that this method turns the experienced operation into auto-control. The quality and quantity of metal is improved greatly and the consumption of electric energy is reduced.In the electrolysis, electrodeposition or electroplating of aqueous solution of copper, lead, zinc, nickel, manganese etc, usually organic additives are added according to the state of cathodic deposit according to experience. This traditional and experienced operation, often lead to that the quality of additive is not optimum which affects the quality and quantity of metal and increases the consumption of electric energy. To counter the controlling problem of the quantity of additive, the authors have invented a corresponding equipment of the auto-control of electrolyte quality [1], it has found application in industrial practice."

Jan 1, 2000

By Janusz Majta

The aim of this work is to investigate the control of microstructure evolution through variation of particular deformation parameters in the two-phase (intercritical) region. Niobium-microalloyed and low-carbon steels were investigated. A detailed examination of the factors affecting the ferrite microstructures of tested steels indicated that there were distinct advantages of finishing at temperatures in the austenite-ferrite region. The various results of deformation in the two-phase region are presented. Consequently, the influence of the most important process parameters on the microstructure evolution and mechanical response of the material is determined. The prime objective of the realized research work is the determination of relationship between the history of deformation and final product quality i.e. texture and mechanical properties. To reach the objective, the constitutive equations are proposed for modeling the effects of the hot-deformation process occurring in the austenite and austenite-ferrite region of low carbon and microalloyed steels on the mechanical properties of the resulting product. These models link advanced, finite element approaches simulating metal flow and heat transfer during hot-plastic deformation with constitutive equations describing microstructural processes and mechanical properties.

Jan 1, 2003

By Shizhe Liu, Bing Li, Heng Wang, Zuxin Zhao

In this paper, cyclic voltammetry and chronoamperometry have been applied to investigate the effects of Nd2O3 concentration on the anode effects, critical potential for the anode effects and Nd2O3 reduction in LiF-NdF3-Nd2O3 melts at 950℃. The results show that the oxidation peaks in the potential of about 2.7V are attributed to the oxygen ions oxidation and the peak current density increases with Nd2O3 concentration increase from 0 to 0.5wt%. The critical potential caused the anode effects shifts to 0.3V more positive value as Nd2O3 content in the melts decreases from 0.01wt% to 0.5wt%. The cyclic votammograms on W electrodes in the LiF-NdF3-Nd2O3 melts present two pairs of reduction and oxidation peaks, indicating that the reduction of Nd ions in the LiF-NdF3-Nd2O3 melts in two steps rather than one step.

Jan 1, 2014

By G. Scavino

A 0.5 wt.% C, 22 wt.% Mn austenitic steel, recently proposed for fabricating automotive body structures by cold sheet forming, due to favorable overall strength and ductility, exhibits plastic localizations during uniaxial tensile tests, whereas no localization happens during biaxial Erichsen cupping tests. Full-thickness tensile and Erichsen specimens, cut from as-produced sheets, were polished and tested at different strain rates. During the tensile tests, the plastic localization phenomena consist first of macroscopic deformation bands traveling along the tensile axis, and then of series of stationary deformation bands, each adjacent to the preceding ones; both types of bands involve the full specimen width and yield macroscopically observable surface relief. No comparable surface relief was observed during the standard Erichsen tests. The stress state being known to influence plastic localization phenomena, reduced-width Erichsen tests were performed with 10 to 30 mm width polished specimens, in order to explore the transition from biaxial to uniaxial loading.

Jan 1, 2009

By Liu Wei

In order to make clear the dissolving characteristic of the chrysocolla (CuSiO3?H2O) in the ammonia-ammonium chloride solution, a thermodynamic model of the chrysocolla (CuSiO3?H2O)-ammonia- ammonium chloride-water system is established using the exponential computation method based on both mass balance and charge balance equations. The equation group of the thermodynamic model is solved by the MATLAB Soft on PC. The condition which is favorable for dissolving high concentration of copper in solution is making out. The stable area of chrysocolla (CuSiO3?H2O) and the condition of chrysocolla (CuSiO3?H2O) converting to atacamite (Cu(OH)1.5Cl0.5) is also studied. A group of experiments are designed to validate the veracity of the results of the thermodynamic calculation.

Jan 1, 2010

By Xiaowen Liu

The thermal decomposition of diaspore was investigated by thermogravimetry (TG),differential scanning calorimetry (DSC), X-ray power diffraction(XRD),infrared (IR)spectrain this paper. The thermal decomposition mechanism of diaspore was discussed according to Coat-Redfer equation. It was found that the decomposition of diaspore was carried out at 500?,and the peak temperature was 530?. The electrovalent balance of diaspore was destroyed. The previous crystal structure was changed. a- Al2O3 was obtained after thermal decomposition. The activation energy is 287KJ/mol.

Jan 1, 2006

By Shekhar Bhansali, Shyam Aravamudhan

"This paper reports on the design and simulation results of a silicon bulk-micromachined diaphragm-type piezoresistive pressure sensor capable of operating linearly over a wide dynamic range (0-1000 meters of water). The piezoresistor elements of the sensor are arranged in a wheat stone bridge configuration to achieve a higher output response. Simulation results (output voltage and sensitivity analysis) obtained using coupled MemPZR-MemMech module of the CoventorWare2003 Finite Element tool are presented. The effect of diaphragm size, diaphragm thickness and thickness of the piezos on output sensitivity were analyzed and optimized to get a linear response over the wide dynamic range.IntroductionThe physical and biological processes in the ocean are critically influenced by ocean parameters (pressure, salinity and temperature). Thus there is a need to develop inexpensive and reliable sensors to continuously measure large volumes of sea-space over long time spans. A key component in any such system will be a pressure/depth sensor. This sensor is routinely employed in marine applications such as wave and tide gauges, tsunami detection, platform leveling etc. More significantly, pressure measurement is needed for depth determination. Depth sensors are vital for remote operated vehicles (ROVs), profiling instruments and towed arrays.Several techniques have been routinely used in the past to measure pressure in the marine environment [1-3]. In general, the pressure sensor design is based on a flexible membrane as the spring element for the sensing pressure [4]. The deflection of the membrane, induced by the applied pressure, is converted into an electrical output through a component that is sensitive to diaphragm deflection (capacitive coupling) or associated stresses (piezoresistors, strain gauges). The temperature compensated pressure measurement can be readily converted to depth using"

Jan 1, 2004

By Jiangtao Li, Zhongwei Zhao, Xingyu Chen, Xuheng Liu

In tungsten ion-exchange process, excessive sodium impurity enters into ammonium tungstate solution. However, the Na content of the final ammonium paratungstate (APT) product must be strictly controlled. Consequently, it is necessary to remove Na from the ammonium tungstate solution during processing in order to obtain the required purity of APT. In this study, porous Na specific absorbent, Na1+xAlxTi2−x(PO4)3, is used to remove Na from the ammonium tungstate solution. Through experiments, the effect of reagent concentration of Na1+xAlxTi2−x(PO4)3, reaction time, reaction temperature and Na concentration on the Na removal were investigated. The results showed that under optimal reaction conditions of reagent amount of NATP 1.0 times of theoretical amount, reaction temperature 25 °C and reaction time 15 min, the Na removal from commercial (NH4)2WO4 solution can reach 98%. Na1+xAlxTi2−x(PO4)3 has a good applicability to different Na+ concentrations. The obtained APT product reaches the national standard purity of zero level.

Jan 1, 2014

By Jonkion M. Font

An expression for the distribution ratio of arsenic between slag and copper matte or liquid copper was developed by both, an extension of the Reddy-Blander moderl for deriving a priori the arsenic capacity, and by a relationship between the arsenic capacity and the arsenic distribution ratio. In this study, the a priori arsenic capacities in the FeO-SiO2, CaO-SiO2,MgO-SiO2, FeO-CaO-SiO2, FeO1.5-CuO0.5-MgO-SiO2, FeO-FeO1.5-CuO0.5-CaO-Mgo and FeO-FeO1.5-CuO0.5-CaO-Mgo-SiO2, slags were calculated at 1573 K. The a priori arsenic distribution ratio between the FeO-FeO1.5-CuO0.5-CaO-MgO-SiO2 slag and copper matte mn (Lx, )' and between the FeO-FeO1.5-SiO2 or FeO-FeO1.5-CuO0.5*-CaO-Mgo slag and liquid copper (Ls/cua) were calculated. The model calculated data are found to be in good agreement with the reported experimental data. The availability of reliable thermodynamic data for slag components and impurities in the slag-matte- metal system is essential for the accurate prediction of impurity capacities and distribution ratio data. The arsenic distribution ratio model developed here, can be extended for predication in multi-componet slags and mattes or liquid metal, and thereby may lead to the development of new slag systems for the efficient removal of arsenic in the copper smelting, converting and refining processes,

Jan 1, 2003

By Vladimir I. Skorohodov

The technology for copper utilization from circuit boards etching is proposed. The technology is based on combination of electrochemical and sorption methods. The conditions of copper electroextraction from ammonia-chloride solutions with obtaining of cathode copper are defined. The stage of electrolysis is destined for copper recuperation from etching process. Due to the electrochemical processes are unacceptable for cathode precipitation of the copper from diluted solutions such as rinse waters, the concentration on the strong-based cationites are used. After filtration throw the sorption columns solution is directed to the stage of circuit boards washing. It allows organizing close loop water recirculation. After saturation. resin is 'regenerated by chloride ammonium solutions. Obtained eluate directed to the etching stage, Generally. the technology provides copper recuperation and minimize wastes amount.

Jan 1, 2001

By Yong Hack Lee

Nonferrous smelting processes have been through a rapid transformation since the beginning of 1980. The copper smelting technology has changed from the conventional Blast Furnace process to the Flash Smelting and MIB process. In the field of lead smelting, the technology has changed from the Blast Furnace Smelting to the Direct Smelting such as QSL and KIVCET. In 1992, Onsan Refinery successfully commissioned Direct Smelting QSL technology for lead. The QSL could produce more than 160,000 ton per year of lead bullion from lead concentrate and various residues. Moreover, since the year 2000, the TSL (Top Submerged Lance) Technology utilizing the same Direct Smelting process has been successfully commissioned to treat lead concentrate as well as lead sulfate residue produced from a hydrometallurgical zinc plant. This paper presents and compares the energy flows of lead smelting processes such as a conventional process and the Direct Smelting Processes plotted on the Pb-O-S phase diagram. The oxygen potential diagram suggests how to control the oxygen potential in the furnace. Also, it describes the recent operational experience in the TSL plant of Onsan Refinery with necessary mass balance of key elements.

Jan 1, 2003

By Akira Kaneda

Mitsubishi continuous process employs an electric furnace for settling matte from slag. Electrodes are immersed into the slag layer in the slag-cleaning furnace and the temperature of the melt is maintained at a predetermined level by Joule's heat. Electrodes are immersed to the depth where the current of each electrode is kept at a set value, and they are raised or lowered automatically to compensate for the deviation from it. Because electric resistance of the bath is varied with the matte level in the furnace and the composition and temperature of the slag, the immersion depth of the electrodes is affected by them. Therefore by monitoring the immersion depth and its change with time, abnormal situations in the furnace, such a~ rise of matte level or local abnormal state of melt, can be detected. In this paper, relations between state of the furnace and electrode behavior are discussed based on the plant data, and then a new and simple monitoring method of the condition of the furnace is proposed.

Jan 1, 2001

By Zhong g. Shui-ping

A new type Pb-Ag (0.8wt%)-Bi (0~5.0wt %) alloy used as anode in electrowinning of zinc from sulphuric acid electrolytes was prepared. The electrochemical properties of this ternary lead alloys have been tested and compared with those of Pb-Ag (0.8wt %) anodes used in industry. Results show the anodic overpotential decreases with the increasing of Bi content in the alloys. When the content of Bi was 1.0 wt% and 5.0 wt%, the anodic overpotential is about 40?50 mV and 60?80 mV lower than that of Pb-Ag (0.8wt %) alloy, respectively. The formation of oxide layers on the surface of these alloys was traced by LSV methods and the composition of the anodic oxide layers was characterized by XRD and SEM analysis. The surface layer on the two type anodes examined is mainly composed of a?PbO2 and ß?PbO2. But different structure of the surface layer was observed, Pb-Ag (0.8wt%)-Bi (1.0wt %) has a more fine-grained structure as compared to Pb-Ag (0.8wt %). But the film on Pb-Ag (0.8wt%)-Bi (3.0wt %) alloy is rather friable, cracked and not tightly attached to the anode.

Jan 1, 2008

By Stephanie Trant

Montana Tech has been engaged in fundamental research on the processing of critical materials for more than a decade. Efforts include examining novel reagents for the flotation of Rare Earth Minerals (REMs). For this paper, research results on a collector, salicyl hydroxamic acid (SHA), are presented. Various REMs were examined and include the rare earth oxides (REOs), carbonates (RECs), and phosphates (REPs) of a suite of Rare Earth Elements (REEs). Differences are attributed to solution and surface chemistry, coordination number, and ionic diameter. SHA adsorption follows an ion-exchange process that leads to chemisorbed and surface-precipitated states, depending mostly on pH. Many effects are directly attributed to lanthanide contraction. Results should also be applicable to other REM/collector systems and further suggest that REM flotation should consider dual collectors.

By Chen-Ming Kuo, Esher Hsu

"Under the 4-in-1 recycling system, Taiwan producers and importers who using packaging containers have responsibility to pay the recycling fees for recycling the waste packaging containers they produced or imported; while the collectors/recycling plants who collect/sort/recover waste packaging containers receive subsidy for conducting recycling. A reasonable pricing for recycling charge and subsidy is a way for sustainability of the recycling. The objective of this study is to provide an amending mechanism for product charge and recycling subsidy in response to the social economic changes. This study employs a regression analysis and cost adjusting model to link the factors used for calculating product charge and recycling subsidy on recycling waste packaging containers with socio-economic indicators, raw material prices, wholesale prices, and secondary material prices. Study results provide estimated models to EPA in Taiwan for amending product charge and recycling subsidy in response to the social economic changes.IntroductionUnder ""4-in-1"" recycling system in Taiwan, waste packaging containers are officially announced to be recycled. The waste packaging containers announced to be recycled include iron cans, aluminum cans, glass bottles, plastic containers, paper containers, aluminum foiled paper packs. In order to compensate the recycling system, EPA charges associated manufacturers and importers for recycling fee and subsidies recyclers to create the economic incentive for raising recycling performance. Basically, the budget for subsidy recyclers is from the recycling charge. That means if we want to increase recycling efficiency by increasing subsidy to recyclers then the manufacturers and importers have to pay more for reaching financial balance of recycling foundation. The benefit of recyclers and fee payers are always conflicted. The recycling charge and subsidy is thus argued by fee payers and subsidy receivers all the time. A reasonable pricing for recycling charge and subsidy is the only way to keep the recycling system sustainable. Moreover, a suitable mechanism has to be changed along with the changing social economic condition. The recycling performances and effectiveness of this recycling system is also highly dependent on the pricing mechanism. This study intends to provide an amending mechanism for product charge and recycling subsidy in response to the social economic change. Related previous studies about recycling system in Taiwan with its performance include Hsu and Kuo (2002, 2005), Bor, Chien, and Hsu (2004) and Hsu (1999). Hsu and Kuo [1] estimated total production values of recycling and evaluated the performance of recycling performance based upon the estimated production values."

Jan 1, 2011

By Wen-Ming Chien

Keywords: AN-KN Phase Transition, Lattice Parameters of AN-KN, X-ray Diffraction The lattice parameters of the low and high temperature phase of KNO3-rich (in NH4NO3) solid solutions have been determined by the X-ray diffraction method. The low temperature single KNO3 phase (KN II) are from 92%-100% KNO3 in NH4NO3 composition range and from room temperature to 393 K showing in X-ray diffraction patterns. The high temperature KNO3 phase (KN I) showed very broad composition range between 20% to 100% KNO3. The lattice parameters of KNO3-rich (KN II and KN I) solid solutions have been calculated at different temperature range. The volumes of orthorhombic KN II phase decrease from 0.3208(3) to 0.3195(3) nm³ at the room temperature as the compositions increase from 95% to 100% KNO3. The lattice constants of the hexagonal KN I phase show that there is no significant change in a-direction when the temperature increases. Details X-ray results and lattice expansion equations during heating will be presented.

Jan 1, 2005

"Mixing phenomena in a bottom blown air-stirred one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor was studie9-using three different configurations of straight circular nozzles fitted axially at the bottom of the vessel. The mixing time has been determined by pH measurements at various gas flow rates, bath heights and nozzle orientations in the presence and in the absence of a second phase.Experimental results reveal that the mixing time decreases with increasing gas flow rate. For a given gas flow rate the mixing time increases non-linearly with increasing bath height. Off-center configuration gives slightly lower mixing times as compared to center configuration. It is found that the contribution of buoyancy to the total stirring energy density is very small, but its contribution increases with increasing bath height. In the presence of an upper oil layer, the mixing time increases significantly for all configurations.IntroductionIn high temperature metallurgical melts mixing is carried out by injection of a gas either from top or bottom of the vessel in order to accelerate the rates of chemical reactions and to promote bath homogenization. When a gas is injected into a liquid through a submerged lance, porous plug or nozzle, the gas, rising as a two phase plume to the surface, imparts momentum to the surrounding liquid and causes gross circulation in the bath which promotes mixing."

Jan 1, 1997

By Anna Wasilkowska

The study concentrates on the effects exerted by microstructure, deformation history and uniaxial stress conditions (temperature, stress state, strain rate) on the mechanical properties offerritic TRIP-aided steels for automotive applications. In low-alloyed TRIP-steels it is quite difficult to separate the effect of the austenite to martensite phase transformation from the influence of the ferritic matrix contributing to the yield stress and uniform elongation. Investigation of transformation kinetics of retained austenite as a function of the deformation temperature show that using the parameter k to characterize the retained austenite stability allows to identify regious of different temperature sensitivity separated by a transition temperature of 10±5°C. The observed low strain-rate sensitivity of the flow stress is an intrinsic property of the ferritix matrix and points to defomtation governed by slip. The ultimate tensile strength is much stronger affected by temperature than the yield stress. The influence of the temperature on the elongation is complex, because of the heating of the specimens by 60-l20°C at moderate and high strain rates. The increase of the total strain can be understood in terms of thermal softening of the ferrite. On the other hand, the steep increase of the stress during dynamic testing is an effect of accommodated elastic and plastic strains in the matrix. The strain- hardening exponent is dependent on the conditions imposed during testing. The martensite transfomtation rate is lower and the critical stress for martensite nucleation is much higher under compression compared to tensile loading. In secondary tensile tests, the yield stress increases steeply, and the ultimate tensile strength and the total elongation depend linearly on the amount of pre-straining. The results confirm that in the range of 8=10-4 s-l the TRIP-effect governs room temperature plasticity. Keywords: TRIP-steels, mechanical properties, strain rate sensitivity, temperature sensitivity, austenite stability

Jan 1, 2003