Search Documents

By Daniel Bennett

There are few methods currently applied towards on-line bulk mineralogical analysis. Yet on-line knowledge of process mineralogy could potentially provide large benefits, such as increased extraction efficiency or resource optimization. The work described in this paper involves the development of radio frequency methods for bulk mineralogical analysis. Some resonances that occur in the radio frequency spectrum are mineral specific, and potentially allow quantitative estimation of mineralogy in an ore stream. Results will be presented on the specific detection of chalcopyrite. Initial quantitative measurements investigating matrix effects have indicated the feasibility of on-line mineralogical estimation using radio frequency techniques.

Jan 1, 2006

By Tsutomu Yamamura

The electrolytic reduction mechanism of rare-earth chlorides such as LaCl3, CeCl3, NdCl3, ` SmCl3 and DyCl3 in alkali chloride baths has been investigated in NaCl, KCI and eutectic LiCI- KCI by means of electrochemical transient methods. The thermodynamic behaviors of rare-earth containing species have been discussed in the frame of Electrode potential - P02- diagram. Low current efficiency found in the case of Nd electro-winning has been attributed to the dissolution of Nd into the bath. The analyses of electrochemical measurement required the elucidation of the effects of the factors such as under-potential deposition, metal dissolution, moisture and oxygen partial pressure.

Jan 1, 2003

By C. W. Whitten

Solis from an abandoned Pb battery processing facility were characterized prior to the selection of the extraction technique. Reflected light microscopy and electron beam methods were used to locate Pb-bearing phases and to quantify the compositions of the phases. It was found that the soils are composed primarily of quartz and feldspars with minor amounts of iron and titanium oxides. Lead is primarily present as an oxide or sulfate that is associated with the silicate minerals. Specific phases identified were PbO; Pb02; cerrusite, PbCO3; angleslte, PbSO4; galena, PbS; and magnetoplumbite, 2PbO3Fe2O3; or plumboferrite PbO2Fe2O3?

Jan 1, 1989

"EAF dust is categorized as a hazardous solid waste. EPA approves only two treatment methods: either sending the dust to zinc recycling facility, or stabilizing it first and then disposing it to a specially-lined landfill. Both treatment methods are costly to EAF steelmakers. In order to reduce the cost and even better to make profit from the dust, EAF steelmakers need to find a costeffective technology to separate zinc from EAF dust. This paper is dedicated to discussion of a novel recycling strategy: in-process separation of zinc from EAF dust. The concept of in-process separation of zinc from EAF dust is first defined, and then a simple Zn concentration model is developed. From this model, two approaches of in-process separation of zinc from EAF dust are derived: (1) prematurely capturing dust at very high temperature when zinc is still in vapor status, (2) prematurely collecting dust immediately after quickly cooling EAF off-gas from high temperature to low temperature. Next, thermodynamic analysis is conducted to understand zinc behavior in EAF off-gas. It is demonstrated in theory that zinc is in vapor status while it exits from electric arc furnaces. At last, recycling routes and economics of in-process separation of zinc from EAF dust are discussed.IntroductionElectric arc furnace (EAF) plays an increasingly important role in steel production. According to USGS, steel production from electric arc furnaces has long exceeded that from basic oxygen furnaces [JJ. In 2009, electric arc furnaces produced 64% of total steel in the United States.Along with the fast growth of EAF steel production, generation of EAF dust is also rapidly increasing. A survey by AIM Market Research showed that 10 - 20 kg EAF dust was generated for every ton of EAF steel produced [2] In 1999, the United States alone produced 770,000 metric tons of EAF dust [3] In Europe, annual generation rate of EAF dust is more than one million tons [4-5]. In Japan, about 450,000 tons of EAF dust is produced each year [6] Globally, total generation of EAF dust was estimated to be more than 5 million tons per year [5] EAF dust is categorized as a hazardous solid waste since it often contains heavy metals, such as lead, chromium and cadmium. US Environmental Protection Agency (EPA) approves only two methods for treating EAF dust: (1) recycling the dust by EAF-dust recyclers, and (2) specially landfilling the dust for disposal after it is chemically stabilized. These two methods of treating EAF dust are both very costly to EAF steelmakers. It was estimated that a fee of $150 to $200 per ton of EAF dust was paid for various treatment options, which added approximately $2 - 3 cost for every ton of liquid steel produced by electric arc furnaces [?J."

Jan 1, 2011

By Shi Yuan

Molten copper was deoxidized using a one-end-closed yttria-stabilized zirconia (YSZ) tube. A thin layer of porous Ni-Zr02 cermet electrode was deposited on the inner wall of the YSZ tube. The outer surface of the tube was in contact with the melt and the inner surface with a flowing reducing gas. Without applying external EMF, the melt was deoxidized by short-circuiting the melt with the cermet electrode. The deoxidation process was analyzed and the rate controlling steps were identified. These experiments were also conducted at different temperatures to evaluate the effect of temperature on the deoxidation kinetics.

Jan 1, 1994

By Vijaya Thangavelu

Biological leaching of low-grade nickel laterite is based on a non-traditional leaching of oxide minerals using heterotrophic micro-organisms. The organisms solubilise metals by excreting organic acids; these acids then form complexes with heavy metals. High salinity of water supplies and soils in the vicinity of nickel laterite ore bodies is a major abiotic stress to fungi and represents a major challenge in the application of bioleaching process in-situ. Salinity exposes fungi cells to Na+ toxicity and osmotic stress. This study examined the salt tolerance development of Aspergillus foetidus based on gradual acclimatization of organism, its salt threshold and the salinity effect on its metabolism. The biological leaching of weathered saprolite ore with the resulting halotolerant organism under saline conditions was assessed. It was observed that salinity stress affected the organism?s growth and energy utilization

Jan 1, 2006

By R. David Prenganan

RSR has developed a new environmentally superior process to recover lead as high purity electn:1o'i0!1 cathode from battery scrap. The process involves crushing the batteries, separating the lead bearing material from the plastic, ebonite and separators, and separating the active material (paste) from the metallic lead fraction. The paste is desulfurized using Na2C03 to convert the PbS04 to PbC03 and produce a sodium sulfate solution. The paste is further treated to decompose the PbO2 and PbC03 to Pbo. The PbO from the treated paste is easily leached, using H2SiF6 and electrown from solution using Pbo2?coated graphite anodes. The electrown lead has a purity exceeding 99.99%. RSR is in the final design stages of a plant to produce 36,000 tons per year of electrcwon cathode from battery paste in a new plant adjacent to the present Indianapolis refinery. This paper describes the work of a pilot facility operated in the early 1980's. The paper describes the patented process in detail and compares the newly designed environmentally clean electrolytic plant to present recycling plants.

Jan 1, 1990

By D. R. Spink

A partial desulfurization roasting (PDR) technique has been developed for use on zinc concentrates whereby the sulfide sulfur associated with the iron content is selectively removed over a very short residence ?time in the roaster. The resulting PDR product is then leached for the selective removal of the iron. The resulting leach restdite is an upgraded zinc sulfide concentrate which has a very low iron content. The up-graded zinc concentrate can be subjected to a conventional dead roast without formation of deleterious zinc ferrite so that hot acid leaching and jarosite (or other) iron precipitation steps are obviated. Examples are presented for the treatment of three very different types of zinc concentrates.

Jan 1, 1990

By Alexandra Anderson

A computational fluid dynamic (CFD) model has been developed using ANSYS Fluent 17.0 to help identify areas of high wear within the refractory lining of a secondary lead reverberatory furnace. Once a base case simulation was validated using data from an operational furnace, areas of potentially high refractory wear were determined through the calculation of the temperature and velocity distributions within the furnace and on the hot face of the refractory lining. The CFD model was used to assess whether the predicted areas of high refractory wear could be minimized through changes burden geometry. The results showed that shape of the burden geometry greatly affected the overall flow patterns and heat transfer within the furnace.

By P. N. Anyalebechi

The effects of application of steady and pulsed electric current on the cast microstructures of ingots of a 7050 type aluminum alloy have been experimentally investigated over a solidification rate range of 0.1-10 K/s. This involved the application of an electric current of 465-930 mA/cm2 of melt surface area to laboratory-size ingots solidified in a unidirectional manner. Within the ranges of electric current density and solidification rate investigated, the applied electric current reduced the average dendrite, grain, and second-phase particle size. It also made the size distribution of the second-phase particles more uniform. The mechanism for the observed refinement of the cast microstructure by the applied electric current is not well understood. The potential effects of heat-induced local convections, shear stress-induced fragmentation of dendrites, increased temperature gradient due to Joule heating and the thermal and constitutional supercooling engendered by Peltier, Thompson, and Joule heating are discussed.

Jan 1, 2009

By Xin Li, Hai-Xing Fang, Bing Xie, Hong-Yi Li

Chromium-containing vanadium slag (V-Cr slag) was obtained by an industrial smelting process of Hongge Ore, which is valuable vanadium-titanium magnetite to extract V and Cr in China. Sodium roasting thermodynamics of V-Cr slag in presence of oxygen were calculated to evaluate the reactivity of chemical compounds. Results showed that the oxidation of FeV2O4 was intensified in presence of Na2CO3 while the oxidation tendency of FeCr2O4 was far lower than that of FeV2O4. It was probably that reactions of impurities including Al2O3, SiO2 and Fe2O3 with Na2CO3 happened and the products can promote the oxidation of vanadium or chromium compounds in lower valence. Based on thermodynamic analysis, a two-step selective extraction process of vanadium and chromium was proposed. Extraction rate of vanadium was 88.6% while 7.0% for chromium in the first extraction step; extraction rate of 90.7% and 95.4% for vanadium and chromium, respectively, were obtained in the second step.

Jan 1, 2014

By Kwong. Kyei-Sing

Gasification is a process that converts a carbon feedstock into synthesis gas (CO+H2). Slagging gasifiers operate at high temperature and pressure and in a corrosive-wear environment from the slag. Cr2O3-based refractory linings are used to protect the steel vessel that comprises the gasifier from the aggressive gasification environment. Increasing service life of the gasifier is one of the keys for wide spread development of this technology. In support of the goals, research on the gasifier atmosphere, the slag chemistry, the interaction of Cr2O3 refractory with different feedstock mixtures (e.g., coal and petcoke) were characterized by post mortem analysis of bricks from service in gasifiers and thermodynamics simulation of the environment. Examples demonstrating how thermodynamic calculations can explain the post mortem results and make predictions of material interactions will be given. Attention is placed on the possibility of Cr+6 in different feedstock mixtures and operating conditions.

Jan 1, 2010

By John J. Moore

This paper discusses the application of a video technique to construct stability diagrams for the combustion synthesis of ceramic-metal composites. Several model exothermic combustion synthesis reactions have been used to investigate the effect of the reaction parameters, eg. stoichiometry, green density, etc, on the stability of the propagating combustion reaction front and subsequent product morphology. The effect of varying the reactants and their stoichiometry to provide a range of reactant and product species ie. solids, liquids and gases, in the synthesis of both dense and expanded (foamed) ceramic and ceramic-metal composites was also investigated with respect to their corresponding combustion front stabilities.

Jan 1, 1993

By Wenming Wang

Recycling of retired cadmium telluride (CdTe) photovoltaic (PV) modules has attracted attention due to new European environmental regulations. Recycling tellurium from CdTe PV modules is becoming more important because of the low availability of this metal. We investigated several treatment paths for reclaiming tellurium from solutions obtained from leaching fragments of CdTe PV modules. Our experiments showed that conventional soda ash neutralization/hydrolysis methods recovered only 50~60% of tellurium. However, by appropriately combining neutralization and sulfide precipitation, almost all the tellurium present in the leaching solution was precipitated and recovered; the concentration of tellurium in the processed solution was reduced from 900-1000 mg/L to less than 1 mg/L, yielding a tellurium recovery greater than 99%. This method can be incorporated in the scheme of recycling spent CdTe PV modules and manufacturing wastes. It may be also an alternative to the current operations for removing tellurium from copper anode slime leaching solutions.

Jan 1, 2006

By Bart Blanpain, Tom Peter Jones, Muxing Guo, Liugang Chen, Huayue Shi

Fayalite based slag is formed during the smelting process of secondary copper resources. It was found that with the presence of high ZnO, the slag became viscous, causing a slag tapping problem. In the present paper, the phase relations of the slag system ZnO-“FeO”-SiO2-Al2O3- CaO (ZnO = 0-12 wt%, Al2O3% = 0-15 wt%, CaO = 0-1.5 wt%, with iron saturation) at 1150 °C is studied by using quenching technique followed by phase identification and compositional analysis of equilibrated samples. The dependence of FeO and Al2O3 solubility in the liquid slag on the chemical composition of slag is characterized. Based on the experimental data, the solid fraction of the slag, which may considerably, influences the slag viscosity, at the tapping temperature can be reasonably estimated and, therefore an appropriate modification of the slag composition can be made.

Jan 1, 2016

By Maria D. Salazar-Villalpando, Anthony Cugini, Bryan Reyes

"The electrochemical reduction of CO2 was performed in a laboratory-made, divided Htype cell. A copper electrode was used as the cathode. An Aldrich Nafion 117-type ion exchange membrane (0.18mm thickness) was used as the diaphragm. NaHCO3 and KHCO3 were studied as the catholytes. Hydrogen evolution from water reduction and products from CO2 electrochemical conversion were recorded. Higher CO2 reduction enhancement was observed by KHCO3 as compared to NaHCO3. The main conclusion of this work is that in fact CO2 can be electrochemically reduced with copper electrodes.1.-INTRODUCTIONThe direct electrochemical reduction of CO2 may allow for a simple process and, by avoiding high temperature reactors, would enable the process production rate to be quickly varied to follow the time of day availability of surplus electricity [1]. Temperature has a major effect on the electrochemical conversion of CO2 since its solubility increases when temperature decreases [2]. The electrical potential applied to the electrochemical reacting system will have an influence on the product distribution, as well. For example, a narrow potential range during cyclo-voltagraphic studies will determine the detection of a lower number of products. A recommended potential range to study the electrochemical reduction of CO2 is -2V to 2V. Moreover, the reaction rate on the electrode is governed by various processes, such as the kinetics of electron transfer, adsorption/desorption at the electrode surface, and diffusion of CO2 to the Cu electrode. The availability of active species, CO2 for electro-reduction, is extremely low at the vicinity of the electrode surface and it seriously interferes with the rate of mass transfer. In batch type electrolytic reactors, depletion of CO2 at the surface takes place first. CO2 from the bulk then has to diffuse to the electrode surface, resulting in mass transfer controlled kinetic phenomena. During the above process, several other competitive side reactions could suppress the primary reaction even though the cathode has good electro catalytic properties for reduction of carbon dioxide. When the dynamic supply of specific active species is ensured to electrode surface, the mass transfer effects are minimized to certain extent. Hence it is envisaged that a continuous flow reactor is more efficient for the electro-reduction of CO2 in CO2 saturated aqueous electrolytes. The primary reactions that occur at the copper electrode during the reduction of CO2 are listed below (with the standard potentials calculated using formation energies [1] :"

Jan 1, 2010

By Gábor Csicsovszki

We have developed a novel method - at the laboratory scale - comprising an ion-exchange separation and a membrane-electrolysis step for the purpose of zero-waste regeneration of spent HCl pickling liquors originating from hot-dip galvanizing of common steels. It is aimed at the parallel regeneration of HCl and iron. Experiments revealed that iron can be electrodeposited at high current efficiencies by maintaining the following conditions: 0.04-0.08 M HCl, 500-1000 A/m2, 20°C and stationary electrolyte in a conventional cell. Zinc in the solution did not disturb the deposition of iron, however it contaminated the product and it poisons the anion-exchange membrane required to tackle acidity during electrolysis. For a preliminary separation, anion-exchange tests were carried out to produce pure iron solutions. Beyond the equilibrium studies, column experiments were carried out showing that low flow rates of the loading solution and the ~1.5 M HCl eluent are essential for separation.

Jan 1, 2006

By Jr. Robison

"Aluminothermic (""thermite"") smelting became commercial with the development of tonnage aluminum, and prospered producing metals and alloys with higher cleanliness, consistency and elemental control than competing technologies. We explore the scope of thermite smelting, and metallothermic smelting in general; the thermochemistry of the process; and its advantages and limitations as applied to industrial production. We review currently-produced products of thermite smelting in several forms and a wide range of heat sizes. As these products serve several industries, we relate the demands of those industries to the requirements imposed on the thermite process, leading to process dynamics and mechanisms to control/alter those dynamics. We review ways to lower the process costs by altering process stoichiometry, using other energy sources and utilizing less costly materials while considering effects on product quality and customer requirements. Finally, we examine overall emissions control and waste disposal.IntroductionAluminothermic smelting is the reduction of various oxides by aluminum to produce metals or alloys with varying levels of residual aluminum. One of the earliest uses of the process was the production of liquid iron to weld railroad rails, later modified in ""thermite grenades"" used to ""spike"" artillery pieces in World War II. Then during the 50's, 60's and 70's the growth of jet aircraft created a demand for new superalloys and titanium alloys, both requiring master alloys for efficient production. Aluminothermic smelting grew with the aerospace industry and with the expansion of microalloyed steels. It is very much a niche industry, dependent on the specialized demands of the specialty steel, superalloy and titanium industries. In this paper we introduce the characteristics of aluminothermic smelting, the scope of smelting operations, the markets served, and the environmental aspects of the process, as seen through the eyes of a company using aluminothermic smelting for over fifty years"

Jan 1, 2012

By K. Dzieciol

The paper presents a study about three image correlation methods ?common cross-correlation, mutual information and phase-correlation ? applied to characterize microstructures reconstructed with X-ray tomography. It is shown that phase correlation is not only the fastest, but also the most sensitive method for detection of similar microstructure features, cavities in the present case. A new image correlation indicator is proposed, which takes into account both the phase shift and the amplitude of similar features in compared images. Some preprocessing aspects related to the tomographic reconstruction and filtering out of characteristic noise are also discussed.

Jan 1, 2009

By Stig Petersson

Slag from the converting of copper matte is usually recirculated to the smelting furnace. This recirculation generally causes disadvantages as magnetite-build-up in the furnace, accumalation of impurities as antimony, lead, nickel etc in the process. The treatment of converter slag in a separate furnace in order to recover the copper and nickel content would be of advantage from several points of view. At the Mining and Metals Division, Boliden, testwork has been carried out to treat converter slag from the PS-converters in a separate furnace. The tests have been performed in laboratory and pilot plant scale. The pilot plant tests have been carried out in a TBRC with charges of 5 tons. Based on these tests a full scale TBRC has been projected in order to treat the slag from the PS-converters. This slag will be reduced with copper concentrates to give a matte and a final slag low in copper and nickel. The background and data from the testwork are presented. Also the lay out, technical data and flowsheets for the projected process are shown as well as some production data from the Rönnskär smelter.

Jan 1, 1976