Search Documents

By Thais Cristina da Costa Caldas, Alline Sardinha Cordeiro Morais, Carlos Maurício Fontes Vieira, Sergio Neves Monteiro

"This work has as its objective to evaluate the firing behavior of a kaolinitic clayey body from Campos dos Goytacazes-RJ incorporated with flat glass waste (FGW) from civil construction. Incorporations of the waste, with a particle size less than 74 µm (200 mesh), were performed in the red ceramic in the following amounts: 0, 2.5, 5 and 10 wt%. Specimens were prepared by uniaxial press-molding and then fired at 850 and 1050°C. The characterization of FGW was done by X-ray Fluorescence. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural rupture strength. The microstructure of the fired ceramics was evaluated by optical microscopy (OM). The obtained results showed that the flat glass waste can be used as a component of ceramic bodies once it was noticed tolerable modifications of technological behavior.IntroductionBrazil is one of the world’s largest producers and consumers of clayey ceramic. Campos dos Goytacazes is located in the north of the State of Rio de Janeiro, southeast of Brazil, it’s known as a large producer of red ceramics. It is estimated that the production of bricks can reach 1 billion pieces per year [1].Nowadays, recycling processes became more and more important, due the generation of wastes in large scale and the preoccupation with environmental. The amount of glass waste has been exponentially growing with the growth of the population. It is estimated that the amount of discarded glass as bottles, construction windows, packing and other glass waste represented in 2006 an amount of 7.5% of the total weight of the world´s domestic garbage [2]."

Jan 1, 2012

By Kuniaki Murase, Tetsuji Hirato, Yasuhiro Awakura

"Electrodeposition of CdTe was studied using aqueous ammonia-alkaline electrolytic baths in which Cd11-and Te1V-ions are dissolving as Cd11(NH3)/+ and Te1vol-ions, respectively. Ca-thodic polarization curves of the baths suggest the presence of strong interaction between the Cd11-and Te1V-ions; electrodeposition of tellurium is inhibited by the presence of Cd(NH3)/+ ions. The interaction makes it possible to electrodeposit CdTe films with stoichiometric composition. Polycrystalline CdTe thin film of about 1 µm thickness was electrodeposited at 343 K from ammonia-alkaline solutions (pH= 10.7) containing TeO32-(<20 mmol dm-3) and Cd(NH3)/+ ( < 60 mmol dm-3) ions. Increasing Cd(NH3)/42+/TeO32- mole ratio or decreasing total concentration of ammonia/ammonium-ion gave flat and smooth crystalline CdTe deposits at constant cathode potential-0.70 to -0.30 V vs SHE at 343 K.IntroductionCadmium telluride (CdTe) is well-known as a compound semiconductor whose band gap, i.e. 1.44 eV, is suitable for solar energy conversion with a photovoltaic cell. Various methods, such as CVD (chemical vapor deposition) and electrodeposition, of preparing CdTe thin films for solar cells have been investigated.Acidic sulfate solutions with a pH of 1-2 are usually employed for CdTe processing by electrodeposition.1-3) The electrodeposition of compound semiconductors is usually achieved (i) at a higher cathode potential than the redox potential of less-noble species, can in this case, and (ii) under the condition of diffusion-limiting current of a more noble species, Te1Y.4) There-fore, a suitable CdII/TeIV concentration ratio in the acidic electrolytic baths, resulting in the deposition of stoichiometric CdTe, is determined by the diffusion-limiting current density of TeIV- reduction, i.e. the concentration of HTeIVO2+ · Since the solubility ofTe1v species HTeIVO2+ in the acidic solutions is quite low, the rate at which CdTe is deposited from the acidic solutions is extremely slow."

Jan 1, 1998

By E. M. Timoshenko

Autoclave technology can be effectively used for liberation of complex mineral raw materials to transfer valuable constituents into solution for their subsequent recovery or to refine feed material in order to remove deleterious impurities, e.g. arsenic. The high efficiency of autoclave processes is attributed to the fact that they are suitable for processing of refractory raw materials, have low capital costs, high productivity, ensure integrated utilization of the feed materials, produce innovative saleable products, completely eliminate any air emissions, provide low-waste or waste-less technology, mechanization and automation of production processes. In the immediate future, it might be expected that autoclave processes will find use on commercial scale for production of heavy non-ferrous metals in combination with other processes (hydrometallurgical, upgrading, sorption and solvent extraction, electrolytic, etc.) to ensure: - Integrated processing of refractory ores and concentrates (pyrrhotite, zinc, copper-zinc, lead-zinc, nickel-cobalt, copper, pyrite); - Production of metallic powders of base metals as commercial products (copper, cobalt, nickel, etc.), composites on their bases, final products and saleable salts. Processing technologies incorporating autoclave processes, especially at the stage of liberation (chemical upgrading) of raw materials are characterized generally by high overall recoveries of valuable constituents significantly exceeding recoveries common for conventional pyrometallurgical processes (for some elements by several tens of percent).

Jan 1, 2006

By Z. Zhang, Zongshu Zou, Nan Wang

"Thermodynamic calculation is applied to make an investigation on the equilibrium phase relations and liquids of CaO-SiO2-Al2O3-FeOx system for different temperatures. The calculated results with FactSage6.1 show that the effect of temperature on the the equilibrium phase relations and liquidus of CaO-SiO2-Al2O3-FeOx system and its sub-systems is appreciable. The liquid phase regions enlarge with increasing temperature from 1573K to 1873K, while the primary phase fields reduce distinctly.IntroductionThe main oxide components of vitrified bottom ash slag are CaO, Al2O3, SiO2, Fe2O3, MgO, and Na2O, accounting for more than 90% of the bottom ash by weight[1]. During slag processing, the knowledge of thermodynamic properties and liquidus temperature in the related slag systems is highly required [2, 3], which is not yet available. Through literature survey [4-6], it is clear that the systematic information on the concerned complex slag system is scarce. So far the engineers in the field have to make assumptions of the thermodynamic properties of the simplified oxide system, without taking into consideration the interactions of the different oxide components, which hinders the development of the slag valorization and utilization. In order to provide thermodynamic properties for the application of the vitrified bottom ash, the six-component oxide system (CaO-MgO-Al2O3-SiO2-FeOx-Na2O) is highly required. A preliminary phase diagram of the CaO-MgO-Al2O3-SiO2-FeOx-Na2O system can be obtained from extrapolation of the thermodynamic functions of constituent subsystems such as CaO-SiO2-FeOx-MgO, CaO-SiO2-FeOx-Al2O3, CaO-SiO2-Na2O-MgO and CaO-SiO2-Na2O-Al2O3. In this work, the equilibrium phase relation and liquidus of CaO-SiO2-FeOx-Al2O3 system, one subsystem of the concerned complex slag system, are calculated and the effect of temperature is also discussed."

Jan 1, 2012

By Jilai Xue

Experiments with various industrial cathodes ranging from 35 wt.% to 100 wt.% graphitic and fully graphitized carbons were carried out in a laboratory aluminum electrolysis cell. Sodium and cryolite bath penetration into the cathode samples was measured by XRD and SEM-EDS analysis. For a higher cryolite ratio in the bath, the cathodes with lower graphitic carbons exhibited more sodium penetration than the fully graphitized. The increased graphitization in the cathode materials can reduce Na, NaF and Na3AlF6 penetration. SEM-EDS inspection reveals that the sodium and fluorides penetration within the cathode samples has different patterns for varying graphitization of the carbon materials. XRD quantitative analysis indicates that there is a large percentage of Na3AlF6 in the penetrated bath. The results can provide useful information for quality evaluation of the industrial cathode products.

Jan 1, 2010

By Joon H. Jang

At a selected pH, hydrothermal oxidation of chalcopyrite was carried out under controlled F+,, at elevated pressures and temperatures (172-200°C) by balancing the rate of oxygen injection against the rate of consumption. Chalcopyrite was converted to covellite (CuS) and digenite (CU1.8S) with rejection of iron and sulfur to the solution. Covellite forms in the first stage, followed by nucleation and growth of digenite in the second stage. The effects of rapid and slow injection of stoichiometric quantities of oxygen are compared. Both the covellite and digenite form a porous layer occupying the same volume as the original chalcopyrite grain. An electrochemical kinetic model is presented to correlate the observed results.

Jan 1, 1993

By Shoji Taniguchi, Lifeng Zhang

"In this paper, firstly the 3D single-phase turbulent steady fluid flow in a vessel with four baffles stirred by a single impeller is mathematically simulated. Turbulence is modeled by using the standard k - e model. Sliding-grid method is used to model the impeller. The flow domain is divided into two cylindrical, the inner one rotates at the same speed as the impeller, and the outer one is fixed with the baffles. Results indicate that the high-speed zone is near the paddles, and larger stirring speed generates larger fluid flow velocity. The calculated stirring intensity data are used to analyze the experimental results. Secondly the effects, such as filter pore size, gas flow rate and NaCl concentration, on bubble size are studied by experiment. For the particle removal rate by bubble flotation in this vessel, first order kinetics is adopted. The effects of initial number of the particles, gas flow rate, particle and bubble size, stirring speed and surface condition, on the removal rate constant are discussed, and an empirical equation is derived by experimental data. At last, a simple model is developed to study the particle attachment probability on bubble surface under turbulent flow conditions. IntroductionIt is well known that inclusions have a bad effect on steel quality. Trying to remove inclusions from liquid steel as many as possible is one of the main objects for the metallurgical workers. Lots of ways are developed to remove inclusions from liquid steel. Gas injection is an effective one. This technique is used to achieve homogeneity in the temperature and metal composition and to assist in the removal of second phase and dissolved impurities from molten steel. Gas injection is commonly applied to the secondary metallurgy processes and continuous casting, for example the ladle argon gas treatment, RH vacuum degassing, and the gas injection in the Submerged Entry Nozzles (SEN) of continuous casting mold, etc. The development of these processes focuses on achieving two conditions: fine bubbles and good mixing. Fine bubbles provide a large gas/liquid interfacial area and a high attachment probability to inclusions, and good mixing enhances the efficiency of impurity transfer."

Jan 1, 2000

By Yufeng Guo

Mineralogy and physico-chemical characteristics of a nickel hydrometallurgical residue and recovery of iron-bearing minerals by flocculation-magnetic separation were studied. The results show that the nickel residue is super-fine and fraction less than 0.045mm reaches 85.4%. Ferrous minerals are chiefly magnetite and ferruginous glass. Magnetite accounts for 31.7% and exists as free magnetite. Ferruginous glass is of multicomponent amorphous substances with low-iron grade but strong magnetism, and accounts for 39.9% of total iron minerals. Addition of flocculants increases granularity and magnetic force of fine iron-bearing particles and improves iron grade and recovery. The tests with flocculation separation show that a concentrate assaying 56.68% Fe with 81.72% recovery was obtained in a magnetic tube. A concentrate with 56.92% iron grade and 67.96% recovery was obtained by flocculation-magnetic separation with a magnetic cylinder.

Jan 1, 2006

By Sergio N. Monteiro

Natural lignocellulosic fibers are successfully replacing synthetic fibers in many engineering applications. In addition to well-known conventional lignocellulosic fibers, others with promising properties are now being considered. The present work investigated the mechanical and structural characteristics of a relatively high strength fiber, curaua (Ananas erectifolius) from the Amazon region of Brazil. The results obtained from tensile tests confirmed the superior strength while scanning electron microscopy (SEM) analysis displayed features that justify the possibility of using the curaua fiber as an effective reinforcement for polymeric composites.

Jan 1, 2006

By R. Y. Wan, S. L. Chryssoulis

"Gold associations were established in a·biooxidized, chlorinated CIL residue assaying 0.02 oz Ault and in a biooxidized thiosulfate leach residue assaying 0.01 oz Au/t. A detailed mineralogical study involved: assays of screened fractions; light microscopy; ion probe microanalysis to quantify 'invisible' gold in sulfide minerals; proton probe microanalysis to detect and quantify preg-robbed gold. In the CIL residue, most of the gold is preg-robbed (71 %). In the thiosulfate leach residue, gold occurs mainly as submicroscopic disseminations in microcrystalline quartz (chert). In both residues, the 'invisible' gold in pyrite accounts for a minor fraction of the gold assay. Quantitative determination of the gold occurrence in the two residue samples established conclusively that gold adsorption on carbonaceous matter in the thiosulfate leach is of minor importance.Acknowledgement: published with permission of Newmont Gold Company."

Jan 1, 1997

By Junhong Noh, Kug Sun Hong, Jung-Kun Lee, Bo Ding

"The photocatalytic splitting of water into H2 and O2 by oxide nanoparticles has received much attention. However, the full potential of photo-catalysts for efficient hydrogen generation out of water has not been fully realized yet due to unresolved limitations including the low electrical conductivity and ineffective carrier extraction. Here, we report composite oxide materials consisting of 1-dimensional (1-D) transparent conducting oxide (TCO) core and TiO2 shell. Highly conductive ITO nanowires were grown on a flexible SUS mesh as a core component. The photoelectrodes consisting of these 1-D nanocomposites have increased carrier mobility due to the TCO core, while the TiO2 shell provides the photocatalytic functionalities. In addition, the built-in-potential at the interface between TCO core and the TiO2 shell improves the collection of charge carriers from TiO2 to TCO. These factors altogether contribute to increasing the photocurrent of the device under light.I. IntroductionPhotocatalytic behavior of semicondcutors has been extensively explored since it was discovered in TiO2 in 197Os. When TiO2 is exposed to UV light, the light is absorbed and electron/hole pairs are generated in the conduction and valeence bands. Holes in valence band will oxide/mineralize pollutant target directly or indirectly (via mediator hydroxyl radical). If the adsorbed A is O 2, O 2 will react with electron from conduction band to generate hydroxyl radical as described in the second set ofreactions. The photocatalytic reaction is schematically explained in Figure 1.Photoelectrochemical (PEC) cells using the photocatalytic reaction have attracted emerging interest as a potential route to convert solar radiation into useful forms of energy by reaction such as water splitting to generate hydrogen1 or the reduction of carbon dioxide.2 Another application ofphotocatalysis is water splitting and CO2 reduction, both of which utilize the electrons that are optically excited to the conduction band. 3•4 For this purpose, the conduction level of the semiconductor should be higher than hydrogen production level (EHZ1HZO) while the valence band should be lower than water oxidation level (Eo21112O). Electrons and holes will be generated on the semiconductor site, and holes generate O 2 at semiconductor site, while electrons will migrate to counter electrode to execute reduction forming H2. In addition to that, materials should be chemically stable to resist photocorrosion and have long lifetime of electron/hole pairs. TiO2 is a suitable material from the viewpoint of band arrangement and chemical stability requirement"

Jan 1, 2012

By Bryn Harris

Much has been written over the past twenty years on the removal and chemical stabilization of arsenic from metallurgical process solutions. This paper reviews again the latest developments in this field, and concludes as before that the high-iron arsenical ferrihydrites, together with the high temperature arsenic minerals, scorodite and Type II, remain as the best and most viable vehicles for industrial control and disposal. However, a cautionary note is introduced, in that chemical environments cannot be considered in isolation, and that cogniscence has to be taken of microbiological activity in determining the disposal method. Data are also presented on a survey of industrial practice, which shows that arsenical ferrihydrite is by far the most widely-practiced and accepted method used worldwide. Finally, the disaster in Bangladesh is briefly discussed with reference to lessons that the metallurgical community might learn from this.

Jan 1, 2003

Microstructural investigation has shown that grain splitting or deformation banding ( DB ) develops progressively with increasing strains during cold rolling. Of particular significance to simulating texture development in cold rolled BCC polycrystals is the operation of higher order slip systems other than 110 and, the occurrence of DB in the rolling plane since the latter allows a new relaxation of the shears. Deformation banding ( DB ) model includes grain subdivision in the rolling plane and applies the Relaxed Constraints ( RC ) mechanism for the other shears. An energy criterion for deciding whether deformation banding occurs or not has been postulated, referred to as Deformation Banding Criterion ( DBC ). This paper reports the results of the investigations into the effects of different slip systems, i.e., those based on 110, 112 and 123 slip planes and their combinations using RC, DB and DBC models, in developing simulated BCC rolling textures.

Jan 1, 1999

"Mechanical alloying (MA) synthesizing technology and thennohydrogen processing (THP) were utilized to produce nanocrystalline Ti-MMC's reinforced by TiB intermetallic compound by using TiH2-B powder mixtures. Powders MA'ed up to 8 hours were examined by X-ray diffraction and SEM study. All MA'ed powders afterwards were HIP'ed at 700, 800 and 950EC for 1 hour. Detailed XRD, SEM and TEM study of the samples were carried out to determine the structure and micrography of the Ti-TiB MMC material processed by MA+THP approach followed by HIP'ing at high temperatures.IntroductionThe fiber reinforced titanium base composites [1,2] which possess a great resistance to high temperature have been investigated. In these studies fibers of C and SiC were used as reinforcing materials. However, these fibers react with Ti-matrix at elevated temperature resulting in product formation at the interface between the matrix and the fiber. Because of the chemical reactions, strength of the product MMC material diminishes.In conventional techniques of whisker reinforced composite material production, the mixtures of matrix metal powders and dispersed fibers are consolidated by hot pressing, HIP and/or hot extrusion. These techniques, however, have some shortcomings. Hard and brittle fibers could be broken during mixing cycle of the processing. Consolidation techniques could also be the cause for fiber breakdown. Attaining of the uniform dispersion of fibers into the metal matrix is not an easy process. The chemical reactions at elevated temperature exposures in the interface between the matrix material and fiber reinforcement cause product formations leading to poor mechanical properties."

Jan 1, 1998

By Rashmi Ramesh

Zinc oxide nanoparticles and nanostructures form an active area of research in the recent years. It can be doped to modify electronic, optical and other properties. Synthesis and characterization of zinc oxide is of extreme importance in order to understand the structure property relationship in this material which is now being considered of importance next to carbon nanotubes. Microstructure of zinc oxide nanomaterial is extremely sensitive to the preparation conditions. Nanocrystalline pure and Mn and Mg doped zinc oxide samples were prepared by wet-chemical method under different growth conditions. The samples were investigated for crystalline phase, microstructure, morphology and luminescence characteristics. The effect of Mn and Mg doping on the characteristics of ZnO have been discussed.

Jan 1, 2010

By H. Masuda

The lijima Zinc Refinery started operation in 1972, and has today an annual capacity of 200,000t-Zn. The hematite process was employed for the first time and the ideal of waste-free refinery has been pursued for 30 years. In recent years, however, only half of the hematite produced would be sold to the cement industry and hence a reduction of arsenic level has been necessary in order to sell the entire amount produced. The arsenic cementation process with zinc powder, developed through a long time laboratory research was found among some options as the best for the hematite process. The construction work started in 2000 and the facility was put into operation in 2001, As a result in the same year all hematite were sold to the cement industry. The outline of this project, present operations and technical issue are reported in this paper.

Jan 1, 2003

By Wellington Pereira Inácio

This work investigated the toughness behavior of polyester matrix composites reinforced with up to 30% in volume of long, continuous and aligned sisal fibers by means of Charpy impact tests. It was found that the addition of sisal fibers results in a marked increase in the absorbed impact energy of the composites. Macroscopic observation of the post-impact specimens and SEM fracture analysis showed that longitudinal rupture through the sisal fiber interface with the polyester matrix is the main mechanism for the remarkable toughness of these composites.

Jan 1, 2010

By Shenghui Guo, Ying Lei, Wei Li, Jinhui Peng, Libo Zhang, Yu Li

"Abstract: In this work, low temperature carbothermic reduction of Panzhihua low grade ilmenite after ball milling were investigated. The ball milling of ilmenite and graphite were processed in a ball mill. The milling process can attenuate the particle of ilmenite, and the ilmenite characteristic peak were broadened and weakened. The reduction temperature and behaviors are studied on the thermo gravimetric apparatus; lower temperature and higher reaction rate were obtained for the reduction of ilmenite with graphite after milled. The reduction temperature and times of ilmenite decreased to 1000-1025°C and 40-60min via milled for 4 or 8h; Low down the reduction temperature can eliminate the solution of Mg2+ and FeTi03 in a certain degree; the reduced ilmenite has an obvious loose structure, can favored the subsequent procedure such as leaching.1 IntroductionThere is about 9.66 billion tons of Vanadic Titan-magnetite deposited in Panzhihua, China. In this reserve, there is about 8.73x108 t ofTi02, Accounting for 90.54% of the Chinese reserves, and 35.17% of the international reserves and ranking first in the world. [JJ Titanium mineral deposits major classified into Rock type and Placer type. Rock type is the igneous mineral, which have great content of FeO (Relative to Fe20 3) and gangue. The rock textures are compact and almost are complex ore. Rock type Titanium mineral major are ilmenite and titan magnetite ore, difficult to separate the metal ore and gangue. l.21 Thus, the Ti02 grade of Rock type ilmenite much lower than the Placer type (Table land 11). Panzhihua ilmenite are the typical Rock-type, due to the higher contents of MgO, CaO and Si02 and the complex mineralogy in ilmenite in Panzhihua region, making its direct reduction progressively more difficult. Mechanical activation, usually carried out by energetic milling or ball milling, was reported to significantly decreased the reduction temperature and accelerate the reaction rate of reduction of ilmenite with carbon, silicon and Magnesium. f3·(>J It reported that the process temperature were decreased to 600-1000°C and the annealing time were reduced to 30-120min after milled for 50-400 h. Shorter milling time involved was imported for else procedure such as direct leaching. 171 Hardly any research had referred to the carbothermic reduction reactivity of ilmeite milled for a short time as 1-1 Oh. In the present work, the aim is to investigate the reactivity and reaction temperature of carbothermic reduction of Panzhihua ilmenite. The Phase composition and micro morphology of samples are characterized."

Jan 1, 2011

By XING Xiangdong, Zhang Jianliang, MA Jinfang, WANG Zhenyang

The non-equilibrium reflux reaction behavior of phosphorus was studied with synthetic slags formed by using the AR chemical reagents and changing the initial condition of basicity, FeO, MgO and Al2O3. Due to increase of viscosity, the dephosphorization slag with high basicity inhibits the full contact of slag with iron, which leads to the low reaction rate in the early stage. However, since the high basicity improves the activity coefficient of CaO, the dephosphorization rate and phosphorus capacity goes up in late reaction stage. FeO promotes the increase of reaction rate in early dephosphorization stage. But the polarization force of Fe2+ is stronger than Ca2+, which hinders the reaction between phosphate ion and CaO and reduces the stability of PO4 3-. Thus, high content of FeO will adversely impact on dephosphorization reaction. In addition, MgO has a promoting effect to the dephosphorization, whereas Al2O3 has a negative influence.

Jan 1, 2016

By J. M. Skeaff

As much as 100% of the gold and 67% of the silver in a sulphur-bearing hydrometallurgical leach residue have been transferred to copper metal at copper smelting temperatures by dissolving the partially calcined residue in an iron-bearing slag maintained in equilibrium with the liquid copper metal and matte phases. The precious metals can then be recovered by conventional refining techniques. Copper can be recycled at least four times without any detrimental effects on gold and silver transfers and recoveries. Apparent copper recovery in the .process can be over 100% because of the copper content of the residue. Based on slag analys.es, the overal1 recovery of gold in the copper metal and matte phases varies from 94% to 100% under all conditions investigated. On the? same basis, silver recovery varies .from 9S% ?to 99% under optimum conditions, but is only 4S% to 73% under other, less attractive conditions. Unaccounted for silver losses of&apos; about 30% make it difficult to determine the major factors affecting ?silver transfer and recovery. A method for implementing the technology on a commercial scale at a Canadian copper/zinc smelter has been proposed. A preliminary economic assessment and comparison of the proposed pyrometallurgical process with conventional cyanidation indicates that either process is economically attractive for recovering gold and silver from leach residues. Although the capital costs are higher, the pyrometallurgical process is simpler, has higher recoveries, lower operating costs and no .potential environmental problems related to cyanide disposal.

Jan 1, 1989