Search Documents

By Tomás Vargas

The catalytic influence of a pure strain of Thiobacillus ferrooxidans (ATCC 19859) on the dissolution of natural pyrite crystals was studied using electrochemical techniques. The results showed that this microorganism catalyze the leaching of pyrite by both, oxidizing ferrous iron in solution and depolarizing the reduction of ferric ion on this sulfide. In addition, studies of bacterial corrosion under applied potential showed that pitting on the pyrite surface centers on weak sites of the sulfide structure in which bacteria has attached, but occurs only when the ferric iron in solution induces an adequate level of anodic polarization on the mineral.

Jan 1, 1992

By Yongqi Sun, Zuotai Zhang

Our study investigated the influence of P2O5 and B2O3 on the viscosity and crystallization behavior of Ti-bearing blast furnace (Ti-BF) slags for the purpose of Ti extraction. The investigation of the crystallization behaviors were carried out using a single hot thermocouple technique (SHTT) and the viscosity was obtained by rotating cylinder method. For the viscosity, the results showed that P2O5 substantially increased the slag viscosity. P2O5 is a network-forming oxide, which increased the degree of polymerization of slags and accordingly increased the slag viscosity. However, both of slag viscosity and apparent activation energy for viscous flow remarkably decreased with B2O3 addition. As a typical network forming oxide, B2O3 was introduced into the network and existed dominantly as 2-D structure, BO3 triangular, which caused a simpler structure and a decreasing slag viscosity. As for the crystallization behaviors of Ti-BF slags, both P2O5 and B2O3 enhanced the crystallization trend of rod-shape rutile and suppressed the crystallization trend of dendrite CaTiO3. Therefore the added P2O5 and B2O3 caused the primary phase change from CaTiO3 to rutile. Additionally, it was found that the rod-shape rutile showed a 1-D growth, whereas the dendrite CaTiO3 showed a 3-D growth style.

Jan 1, 2015

By Shigem Kuramoto

Pure copper is known to exhibit intermediate temperature embrittlement when it is deformed at a slow strain rate, and a small addition of zinc suppresses this embrittlement. In the present study, the relation between zinc addition and hydrogen behavior was taken into account since the impurity hydrogen is believed to deteriorate the ductility at intermediate temperatures. Pure copper and Cu-l mass % Zn alloy specimens are prepared by melting in argon and in vacuum, so that a comparison can be made between the specimens with normal hydrogen content and those with' less hydrogen content. Tensile tests are performed at temperatures ranging from room temperature to 600 "C, and hydrogen behavior is analyzed using a newly developed testing machine that can detect gas evolution from the specimens during deformation and fracture in ultra high vacuum. The small addition of zinc to pure copper decreases hydrogen content, leading to the improved ductility at intermediate temperatures. In addition, the samples of both pure copper and Cu-1%Zn melted in vacuum exhibited higher ductility at intermediate temperatures than those melted in argon atmosphere, which is attributed to reduced hydrogen content.

Jan 1, 1998

By Patrice Chartrand, Halvor Dalaker, Philippe Ouzilleau

A size-dependant thermodynamical model for the carbon-hydrogen previously developed by Ouzilleau et al. [1] has been expanded here to include chemisorption of methyl groups. Gibbsenergy minimalisation calculations using FACTSAGE software on this model indicates that hydrogen bonding through methyl groups is energetically favoured as an intermediate between bonding as monoatomic hydrogen to edge hexagons (which is more favourable) and as monoatomic hydrogen to corner hexagons (which is less favourable). The model has also been applied to methane decomposition and oxide reduction using natural gas. A C-H solid solution as a thermodynamic description of the solid carbon phase influences calculations of carbon activity in metastable methane, and gives different results than when using graphite.

Jan 1, 2015

By P. G. West-Sells

Recovery of gold from thiosulfate leachates can be accomplished by adsorption of the gold thiosulfate complex by a strong base resin. Two of the most significant impurities that can decrease this gold adsorption are tetrathionate and trithionate, which are produced as oxidation products of thiosulfate during gold leaching. This paper investigates gold adsorption on a strong base resin (Purolite A500C) as a function of the concentration of these impurities. It is shown that concentrations of tetrathionate and trithionate as low as 150 mg/L can decrease gold loading by an order of magnitude, and that of the two ions, tetrathionate has a stronger detrimental effect. The resin and solution gold concentration profiles were successfully fit using a Freundlich isotherm, which further shows the strong effect of tetrathionate. To counteract the decrease in gold adsorption by tetrathionate, a novel process was proposed. Sulfite was added to the solution to oxidize tetrathionate to trithionate, and a nitrogen blanket was added to ensure that no further oxidation of thiosulfate could take place. It is shown that by incorporating this process, gold adsorption was doubled from both synthetic and real gold thiosulfate leachates.

Jan 1, 2003

By Toshiro Kuji, Masakazu Fujita, Tetsuji Saito

"The magnetic properties of the magnetic materials were deeply dependent on the microstructures. In this study, the novel technique to produce the desired microstructures in a controlled manner was proposed. The technique consisted of the production of the amorphous alloys and the control of the crystallization process. The technique was applied to improve the magnetic properties of Nd-Fe-B permanent magnets. The microstructural control of the magnets exhibited the excellently high energy-products of higher than 430 kJm-1. The relationship between the magnetic properties and the microstructures of the Nd-Fe-B permanent magnets was discussed.IntroductionThe intrinsic properties of the materials are basically determined by the properties of the constituent elements or the compounds. However, it is often noticed the difference between the observed properties and the theoretical values expected from the intrinsic properties of the materials. This indicates that the observed properties of the materials are determined not only by the properties of the constituent elements. In other words, the observed properties of the materials are also strongly dependent on the morphology of materials. This means that the microstructural control may creates a great improvement of the properties of materials.In Nd-Fe-B permanent magnets, the superiority arises from the uniaxial intermetallic Nd2Fe14B compound which has a large saturation magnetization and a high anisotropy field [1,2]. The magnetic properties of the Nd-Fe-B permanent magnets are dependent on the microstructure, that is, the size, shape and degree of the crystallographic alignment of the Nd2Fe14B phase. Currently, the Nd-Fe-B permanent magnets have been produced by either sintering or melt-spinning [3,4]. In the sintered magnets, alignment of the Nd2Fe14B phase is achieved by the prior green compaction of the crushed ingot powders in an applied magnetic field [3]. In the melt-spinning approach, alignment of the Nd2Fe14B phase is achieved by hot deformation [5]. Amorphous melt-spun ribbons are comminuted and then are consolidated into bulk form by hot pressing before hot deformation. As-hot-pressed magnets have randomly oriented Nd2Fe1~ grains [6]. Subsequent die upsetting of as-hot-pressed magnets gives rise to the crystallographic alignment of the Nd2Fe14B phase."

Jan 1, 1998

By Juan Ruiz-Ornelas, Yousef Mohassab, Ricardo Morales-Estrella, Hong Yong Sohn, Noemi Ortiz-Lara

The effect of mechanical activation on the reduction kinetics of magnetite concentrate by hydrogen was studied. The magnetite concentrate was milled for 8 h using a planetary mill. After the milling process, the average particle size was reduced from 14 to 4.4 m resulting in a lattice microstrain of 0.30. Thermogravimetric experiments were conducted to focus on the chemical reaction as the rate controlling factor by eliminating external mass transfer effects and using a thin layer of particles to remove interstitial diffusion resistance. The onset temperature of reduction was decreased due to the mechanical activation, and the degree of conversion was decreased by sintering of particles which was confirmed by SEM analyses. In view of the results, a reaction rate expression is discussed from which the activation energy is calculated.

Jan 1, 2016

By T. T. Chen, J. E. Dutrizac

Noranda Inc., CEZinc presently employs a cement-stabilization (jarofix) process to stabilize its jarosite residues for direct disposal. In this process, Portland cement partly decomposes Na-jarosite to form Ca6Fe2(SC>4)3(OH)i2.nH20, ferric hydroxide and sodium sulphate which further reacts to form gypsum; approximately one-third of the Na-jarosite reacts in the current commercial product. The cured jarofix products also contain minor amounts of various Ca-Al-Fe silicate-sulphate-hydrate phases and traces of calcite. Together with gypsum and a Ca-Fe sulphate phase, these species bond the various particles together, imparting mechanical strength and reducing the permeability. Water-soluble Zn and Mg are stabilized in the Ca-Al-Fe silicate-sulphate-hydrate phases. The freshly cured products usually contain small amounts of moisture and traces of residual Portland cement, which provides additional alkalinity for the neutralization of any residual acid species. Jarofix products stored for more than six years in the laboratory, after curing, are usually dry and exhibit the same micro-textures as those of the freshly cured products. However, the stored products are depleted in the Ca6Fe2(S04)3(OH)i2.nH20 and Portland cement phases, and are enriched in gypsum and calcite which reflects the highly alkaline environment of the jarofix products. The aged products also have increased amounts of the Ca-Al-Fe silicate-sulphate-hydrate phases which have elevated Zn and Mg contents. This implies a further immobilization of residual water-soluble Zn and Mg during stora

Jan 1, 2000

By Hidefusa Takahara, Koichi Miyake, Dierk Raabe

"Mechanical properties of copper wires were examined. The copper wires containing 5-10 mass % chromium and 1-3 mass % silver were produced through heavily cold deformation. It was expected that the copper wire was easily fractured during cold deformation because of the existence of brittle chromium phase in the alloy. In fact, the copper wire was fractured due to large work hardening, when the true strain [n] exceeded 5. However, the copper wire annealed at 1273K for 6 ks ·in the middle of deformation process could be smoothly drawn to 11=8. After precipitation treatment for silver phase at 473k for 1.8 ks, the wire was able to further drawn to n=8.4. The final deformed wire showed tensile strength higher than 1200MPa.IntroductionDownsizing of electronic devices has led to the demand of finer and higher strength materials for cables. Conventional copper alloys have about 800MPa in ultimate tensile strength. These strength are mainly obtained by precipitation hardening. Nowadays, a process for higher strength wire has been developed, where dual phase copper alloy is used. When it is drawn heavily, the' second phase is elongated along drawing direction and the wire gets high strength due to fiber reinforcement (1). That alloy is so called in-situ formed fiber reinforced ·alloy. Cu-Ag(2), Cu-Nb(3) and Cu-Cr(4) systems are well known as such alloys. It is also well known that chromium is brittle material except single crystal and high purity of chromium. However, Mihara et al. C5l have achieved 1 GPa in ultimate tensile strength in the Cu-Cr-Zr and Cu-Cr-Ti alloys by appropriate thermo-mechanical processing.In this study, the Cu-Cr-Ag systems were investigated: The alloys contained 10 or 5% chromium and 3 or 1 % silver. It was demonstrated that silver precipitated in copper matrix contributed on further hardening."

Jan 1, 2000

By Peter Forschner

Classical Mixing Theory is based on applying many fundamental correlations to standard baffled dished bottomed vertical cylindrical vessels with high degrees of symmetry. Horizontal autoclaves operating at elevated temperatures and pressures have been used for more than two decades. All compartments and especially the first and last compartments are asymmetrical. To date no comparison of the effects of the asymmetric geometry on mixing system design and scale-up has been published. The results of investigating solids suspension, mixing time, momentum transfer from the impeller to feed slurry and feed inlet location in the first autoclave compartment are presented as influences on residence time distribution. CFD modeling was developed and verified with the test apparatus.

Jan 1, 2003

By Norbert Hort, Karl Ulrich Kainer, Carsten Blawert, Daniel Fechner

"With the development of new heat resistant magnesium alloys, the automotive industry has introduced several parts to the drive train. The rising number of large magnesium components will result in a higher quantity of automotive post consumer scrap and the changing legislation will force car manufacturers to take magnesium recycling into consideration. So far post consumer scrap has not been used for magnesium alloy production. Quite a reasonable amount of automotive scrap is likely to end up in a mixed light metal shredder fraction. The separation of mixed magnesium scrap according to several alloys is complex. Therefore secondary magnesium alloys made from blended post consumer scrap would be useful. For this work a matrix of potential recycling alloys was prepared by chill casting and high pressure die casting. The materials were investigated for their microstructure, mechanical properties, heat resistance and corrosion properties. The results will be presented in this paper.IntroductionWithin the last ten to fifteen years several heavy magnesium parts have been assembled in passenger cars, such as gear box housings and crank cases [1, 2]. Reasons are the lately developed new heat resistant alloys and the increasing responsibility of automotive manufacturers to reduce the vehicles weight and thereby CO2 emissions. The latter is pushed by international legislation [3, 4]. The rising quantity of magnesium in automobiles will result in an increasing amount of so called post consumer scrap at the end of the vehicles life.So far magnesium recycling was done only for clean scrap that is free from impurities, contaminations and sorted according to a chemical composition or a single alloy respectively [5- 15]. The latter is also called class 1 scrap and mainly consists of sprues and runners from magnesium die casters [15, 16]. For the upcoming automotive post consumer scrap the materials quality strongly depends on the way end of life vehicles are treated. By proper dismantling of old cars, the bigger magnesium components could be collected and possibly treated similar to class 1 scrap [15]. Up to date automotive manufacturers have no uniform recycling system for end of live vehicles. Most probably a considerable quantity of old cars will be shredded. The resulting light metal shredder fraction will contain aluminium and magnesium scrap, both from several alloys. A separation of mixed magnesium and aluminium scrap is feasible according to [17]. Other authors claimed that the grade of separation of magnesium from aluminium is still not sufficient for a proper industrial recycling process of magnesium post consumer scrap [15, 16]. If an automatic sorting is possible it will probably be very expensive [18]. Therefore, so far the main use of post consumer scrap has been the steel desulphurisation and aluminium production [15]. The use of post consumer scrap for magnesium alloy production has been considered already by [15] and [16] but some problems have to be approached."

Jan 1, 2008

By Keizo Uematsu, Satoshi Tanaka, Nozomu Uchida, Anze Shui, Joaquin Lira, Cyril Lavelle, Midori Saito, Thierry Poirier

"Dispersed and flocculated alumina (non-spherical particles) slurries were prepared by pH controlling with HCL Spray-drying of these resulted in dimpled granules with a smooth surface and high density, and spherical granules with rough surface and low-density, respectively. Detailed characterization on granules and their compacts includes: SEM observation, density measuring (mercury porosimetry and Archimedes's Principle) and liquid immersion optical microscopy. Compaction of these granules originated a larger particles rearrangement in the samples made with the spherical granules than with the dimpled granules. This was verified through the orientation of alumina particles, which was pronounced in the compact made with the former granules.IntroductionOn immersing a ceramic powder in water, the surface usually acquires a charge by interaction with ionic species in solution. The charge is affected by pH and the electrolyte concentration of the water. 1 The dispersion in a slurry is achieved through the interaction of charges on the particle surface with the media. In the ceramic processing, especially in the process of casting, the dispersion of slurry has been one of the most important topics studied for many years. Recently the attention is paid on its role in the pressing. The granule characteristics are governed by the dispersion state of slurry. Takahashi et al2 , Tsubaki et al3 and Walker et al4 showed that the granules from dispersed slurry were dimpled and of high density, while granules from flocculated slurry were spherical and of low density. This variation in the granules characteristics should have a marked effect on the structure of compact.This paper presents the influence of the dispersion state of alumina slurry on the granules characteristics and also on the internal structure of compacts. Different dispersion states were elaborated by adjusting pH of the slurry. In this method, the particles are dispersed or flocculated only by the effect of surface charging, and thus some secondary effect such as the steric hindrance from an electrolyte dispersant is avoided. The characteristics of granules and compacts are examined with SEM, density measurements by mercury porosimetry and by Archimedes's Principle and liquid immersion optical microscopy. This novel microscopy provides various important information on packing structure of particles, such as their orientation. 5"

Jan 1, 2000

By A. Erçin Ersundu

In the present work, three different domestic iron ores; Sivas Divrigi B Head high grade hematite lump ore, Malatya-Hekimhan-Hasançelebi medium and low grade magnetite lump ores reduced with Soma-Kisrakdere lignite coal to investigate their suitability for sponge iron production. A laboratory scale box furnace was used to carry out the reduction experiments. In the experimental studies different operation parameters were selected being Cfix/Fetot. ratio, temperature in the range of 1100 - 1250 oC and time, to determine their effects on metallization. Metallization degree up to 90 % was found in the reduction experiments realized by using Sivas Divrigi B Head high grade hematite lump ore, whereas for Malatya-Hekimhan-Hasançelebi medium and low grade magnetite lump ores 60 - 65 % metallization degrees were obtained.

Jan 1, 2008

By Xi-Shan Li, Qian Li, Yong-bin Yang, Li-na Cui, Tao Jiang, Jie Ge

"With regard to control environment pollution in the roasting pretreatment of sulfur & arsenic-bearing gold concentrate, roasting of double-layered pellet was proposed. In the paper, the characteristics of double-layered pellet roasting were studied. Removal and solidification rates of sulfur and arsenic were investigated as primary factors. The result indicated that the removal and solidification rates of arsenic reached up to 95.91 % and 98.95% while the sulfur was 97.19% and 97.90% respectively on the premise of adopting slaked lime as solidified agent at temperature of 6000, the package proportion of 2.14 and roasting time of 3h. However, pyrite and arsenopyrite were transformed to hematite and magnetite and product of solidification mainly consisted of calcium sulfate, calcium arsenate and calcium sulfite within optimum roasting parameters.IntroductionUtilization of refractory gold resources has been gradually concentrated on with the depletion of the gold resources which are easy to deal with in the world [1]. Sulfur and arsenic-bearing gold ore is a typical refractory gold one, in which ultrafme gold is encapsulated in the structure of metal sulfide minerals [2,3], so it gives poor recovery through direct cyanide leaching. These refractory ores need pretreatment before the process of cyanide leaching to undermine lattice structure of pyrite and arsenopyrite containing gold [4] so that the gold could touch with cyanide solution [5]. Among various methods of pretreatment, conventional roasting method is most effective, but this process generates gases such as S02 and As203 harmful to environment. Therefore solidification roasting was proposed to solve this problem occurring in the conventional roasting at the end of last century."

Jan 1, 2013

By Marcelo E. Andia

In Chile, a significant amount of mining takes place in varied geographical environments. Mining activity extends from copper and gold deposits located in the Atacama Desert 4.500 meters above sea level to underground coal workings beneath the sea floor. This diversity in location and environment presents many challenges in the development of competitive and environmentally sustainable mining activities. An important future issue will be how to close these mines in an appropriate way once economically exploitable ore reserves have been exhausted. This poses challenges for both the government and companies alike, considering that Chilean law currently lacks legislation specific to mine closure. This paper examines the risks associated with mine closure based on international experience, and identifies those risks specific to Chilean regions. The main regions in Chile where mine closure legislation should be applied are identified.

Jan 1, 1999

By Jiang Feng, Li Chuanhua, Zhang Libo, Peng Jinhui, Ju Shaohua

Solvent extraction of Cu2+ from the leaching liquor contain Cu and Fe use a microfluidic technology. Currently, the conventional copper extraction process has many problems such as long distance and small driving force of mass transfer. In order to solve the problems, studies are carried out on the extraction process of low grade copper leaching liquid using Lix984N as an extractant with a new microfluidic solvent extraction technology. The effects of flow rate on the separation and extraction efficiency between Cu and Fe are studied, and the results show that a steady liquid-liquid interface of laminar flow is form in the micro-extractor, and extraction efficiency is 78 % and 2.5 % for Cu and Fe at the contact times of 0.84s respectively. Besides, the separation coefficient between Cu and Fe is as high as 140.04. The studied microfluidic technology has the advantages like improving extraction efficiency and reducing reaction time and providing the potential application in the hydrometallurgy extraction of Cu.

Jan 1, 2015

By Lv Guozhi, Niu Liping, Shi Guanyong, Liu Yan, He Jicheng, Du Yanjun, Dou Zhihe

"We proposed thermit reduction-electroslag remelting method of preparing the large scale CuCr alloy. But there are pores and oxide inclusions in CuCr alloy prepared by thermit reduction process. This paper studied mainly the effects of ratio of reactant and additive on the inclusion type and their occurrences in CuCr alloy. The alloy prepared in different process conditions was characterized via XRD, SEM, OM and TEM and metallographic microscope, in which the existing state and micro-structural defects of inclusions are analyzed. The results show that there are three distinct regions: copper-rich regions, chromium-rich regions and the inclusion regions. Inclusions are mainly in the form of stomata and Alz03 phase, mainly locating in the copper-rich phase and the interface area of chromium-rich phase and the copper-rich phase. Adding Na3AlF6 and heating agent can effectively reduce the inclusion content in the alloy.1 IntroductionIn recent years, with the development ofhigh power vacuum and high-pressure technology ,the CuCr alloy contact material which has many advantages gradually replaced the traditional W-Cu and Cu-Bi series alloy contact material, and become the first choice of material in high-voltage and high-power vacuum switch contacts['-3l. The traditional powder metallurgy method, infiltration method and vacuum arc melting method[4-SJ are using metal Cu powder and Cr powder as raw material by casting molding, and have disadvantages such as high production costs, complicated process, poor product density and low yield, especially in the large size alloy ingots[9-12l. At present, the world regards CuCr alloy new preparation technologies as the first place, and how to achieve a large size the CuCr alloy ingot preparation has become a hot research of CuCr alloy[3l. Zhang Ting-an and Dou Zhihe[l-3l who are supported by national natural science fundation of china successfully successful developed new technologies and core equipment to prepare large-size copper-chromium alloy through aluminum thermal reduction-secondary refining method, and obtained two national invention patents. The method includes two key steps: one is get CuCr alloy consumable ingot by Thermit-SHS with electromagnetic stirring, the other is to refme the CuCr alloy ingot to remove the pores, inclusions and other defects by electroslag remelting technology to get dense and uniform CuCr contact material. The preliminary study results show that means of electromagnetic stirring evidently inhibit effect of alloy ingot macrosegregation during the electromagnetic casting stage, but there are still microstructure defects such as alumina inclusions and pores in the alloy ingots. Therefore, Zhang Ting-an et al refer new ideas of using the electroslag remelting to refine Cu Cr alloy ingots and effectively remove the defects of the ingots such as pores and inclusions [3l _ At present, there is no report of study on the electroslag remelting refining processes of CuCr alloy (the refining slag, remelting current). This article will research mode of occurrence and distribution law of inclusions in the large-size CuCr alloy ingots by Al Thermit-SHS under magnetic field stirring action and provide a theoretical basis for chosing refining slag to remove inclusions by electroslag refining. Meanwhile the article analyses the effect of reduction conditions of Thermit-SHS on the types of inclusions, mode of occurrence and distribution of regular inclusions in alloy ingot, and refer theory for inclusions regulation in the large-size alloy ingots."

Jan 1, 2013

By Elli Nurminen

Fouling of heat recovery process equipment may significantly decrease their heat transfer efficiency. In Copper Flash Smelting process flue dust tends to form build-ups on the heat recovery boiler walls. Thermal transportation properties of copper flash smelting flue dust and its components have been studied. The effects of porosity and temperature on thermal transportation properties have also been determined. The results indicate that dust and its components are effective thermal insulators and build-up layers on the boiler walls are likely to decrease greatly the heat transfer efficiency of the boiler. Decreasing dust layer porosity has a strong increasing effect on thermal conductivity and increasing temperature has a slight decreasing effect on thermal conductivity. The results may be used in CFD-modelling and optimisation of the process.

Jan 1, 2006

By Henrique Ventura Oliveira

Continuous casting is the most important process for solidification of steels. In this process, the fluid flow pattern in the tundish and in the mould have significant effect on the product quality. Problems associated to fluid flow in the tundish include surface turbulence, ?short-circuits?, formation of dead zones and vortexing. During grade changes, mixing in the tundish plays a significant role in determining the length of the intermixed slab. All these flow aspects can be studied by means of mathematical and physical models. In the last years, numerical simulation of fluid flow has become a very popular tool in the analysis of the performance of continuous casting tundishes. In setting-up these numerical simulations, special care should be taken in choosing the appropriate mesh distribution, the interpolation scheme, the adequate location of the inlet boundary and the turbulence model. In the present paper, turbulent fluid flow in different configurations of tundishes was simulated. Different turbulence models were used in the simulations. Residence time distribution (RTD) and mixing curves during grade changes were predicted and compared to results obtained in physical models. The performances of the different turbulence models were evaluated. For the tundishes that have been studied, the performances of the different turbulence models tested in the present work were similar. There is no evidence that any of the models provided sustained improvement when compared to the well-established standard k- model. All turbulence models tested presented limitations in simulating flows under low turbulent Reynolds numbers.

Jan 1, 2006

By Yuanbo Zhang, Guihong Han, Guanghui Li, Tao Jiang, Zengqing Sun, Yanfang Huang

"Because of small specific surface area and poor ballability, vanadium/titanium-bearing magnetite is difficult for production of oxidized pellet. A novel organic copolymer binder, modified humic acid (MHA), has been authorized recently in China. Effects of the novel MHA binder on the quality of V/Ti-bearing magnetite pellets are studied in this paper. Experimental results show the MHA binder can obviously improve the strength of green pellet. Because of better heat endurance, the MHA binder pellet has a higher strength than Peridur pellet under the same preheating conditions. Moreover, TFe grade of pellet with the MHA binder is much higher than that of the bentonite pellet. The strength of preheated pellet containing MHA binder of 0.25%~1.0% meets the requirements of oxidized pellet production by grate-kiln process. Comparatively, MHA is a promising orgainc binder for iron ore pellets. Its price is only one tenth of Peridur price and about 3 times of bentonite price.IntroductionThe iron-making practices show that the use of pellet is beneficial to blast furnace life, productivity and fuel savings. Therefore, many iron-making plants have expanded the production of oxidized pellets in order to meet the needs of modern large-scale blast furnaces [1]. Presently, bentonite is widely used to improve the quality of iron ore pellets. The negative effects of using bentonite include decreasing total iron (TFe) grade and degrading the metallurgical properties of the final products [2, 3]. Many studies, therefore, have been conducted on the application of organic binders to overcome the weakness of the inorganic bentonite. In comparison with inorganic binders, one of the biggest strengths of organic binders is low residual silica content [4]. However, those studies showed that the economics of foreign organic binder addition into pellets was not attractive. For example, the compression strength of preheated pellets and roasted pellets are both too low, resulting in powder generation and ring formation in the industrial rotary kiln [3, 4]."

Jan 1, 2011