Search Documents

By S. Yokoya

With increasing requirement of steel productivity and quality in continuous casting in the conventional casting system using an immersion nozzle, it is very difficult to establish a reasonable molten flow pattern. In order to overcome this difficulty, we propose a new method of imparting swirling motion onto the flow in the immersion nozzle and to control the flow pattern in the mold. Following results have been obtained during the studies. For the case of slab continuous casting mold: High amplitudes of oscillation with a period of 10 to 15 seconds are observed in the outlet flow of the immersion nozzle and meniscus flow in the conventional casting system, while these phenomena are remarkably suppressed using swirling motion in the immersion nozzle, which leads to very calm and uniform flow pattern at the outlets of the immersion nozzle, in the mold and on the meniscus in the mold; For the case of billet continuous casting mold: (1) heat and mass transfer near the meniscus can be remarkably activated compared with a conventional straight type immersion nozzle without swirl, and (2) Quite different mold flow patterns are observed between the divergent and straight immersion nozzles. Heat and mass transport in the mold using the divergent nozzle is much more reasonable compared to that of straight nozzle. The findings, mentioned above, are very useful to control the flow pattern in the slab, and billet continuous casters. Such effectiveness of swirling flow in the SEN on the mold flow has been put into practical use. As a result, remarkable progress on the quality and production of continuous casting products has been observed in practical application.

Jan 1, 2006

By Cheng Gong-jin, Chu Man-sheng, Liu Zheng-gen, Zhang Yong, Liu Jian-xing, Xue Xiang-xin

"High chromium vanadium-titanium magnetite is one kind of Fe-V-Ti-Cr composite ore resources, which owes high utilization value. Owing to lacking systematic study on the sintering of this ore home and abroad, effects of carbon addition and basicity on sintering process and sinter metallurgical properties, such as sinter yield, vertical sintering speed, tumbler strength, sinter machine utilization coefficient, and low temperature reduction degradation were investigated systematically under laboratory conditions in the paper. The results shows that, when high chromium vanadium-titanium magnetite proportion is kept unchanged as 13% in sintering feeds, sintering process index and metallurgical properties are the optimum under carbon addition 5.0% and basicity 2.70, which meets the requirements of blast furnace burdens. This research provides technical parameters for practical sintering production of high chromium vanadium-titanium magnetite.IntroductionHigh chromium vanadium-titanium magnetite (hereinafter abbreviated as hi§h-Cr V-Ti magnetite), in which Fe is closely symbiotic with Ti and isomorphous with V and Cr1'- l, is one kind of typical vanadium-titanium magnetite resources with high comprehensive utilization value but the difficulties are extremely high due to complex chemical composition and mineral structure. At present, the feasible and mainstream utilization process of high-Cr V-Ti magnetite should be the route of agglomeration-blast furnace smelting. Thus, sintering production is the foundation for high-Cr V-Ti magnetite utilization. However, till now there are few research documentations on high-Cr V-Ti magnetite sintering home and abroad. Under the above background, this study focused on detailed researches of high-Cr V-Ti magnetite sintering. Sintering process uses the powders or fine iron ores to produce artificial rich ore with good metallurgical properties 4l Solid fuel provides 90% heat requirement during sintering15J. The appropriate amount of fuel and flux should be added during sintering in order to provide necessary heat and maintain the desired basicity16l. That is to say, carbon addition and basicity are two key factors affecting metallurgical properties of sintering products17J. Therefore, the effects of carbon addition and basicity on sintering process and metallurgical properties, including sinter yield, vertical sintering speed, tumbler strength, sinter machine utilization coefficient, and low temperature reduction degradation, are systemically investigated under laboratory conditions in the study, on purpose to achieve the optimization of sintering process for high-Cr V-Ti magnetite."

Jan 1, 2013

By Naoki Hiroyoshi

It is generally accepted that ferric ions are effective for leaching chalcopyrite as an oxidant and ferrous ions contribute to the leaching only as a source of the oxidant ferric ions. However, this paper shows that ferrous ions are more useful for leaching chalcopyrite than oxidant ferric ions in sulfuric acid solutions in air at ambient temperatures. Leaching experiments and dissolved oxygen consumption measurements were carried out with a very pure chalcopyrite and 0.001 - 1 mol dm-3 sulfuric acid solutions containing 0 - 0.1 mol dm-3 ferric or ferrous ions at 303 K. Chalcopyrite oxidation with dissolved oxygen was promoted by ferrous ions but suppressed by ferric ions. As a result, the amount of extracted copper was larger with ferrous ions than with ferric ions. Effects of Thiobacillus ferrooxidans on the ferrous promoted chalcopyrite leaching were also investigated and discussed based on the experimental data.

Jan 1, 1999

By Paul-Dominique Oudenne

This paper reviews the experience gained by CMI NESA over the last thirty years for the treatment of arsenical and antimonical bearing concentrates and other complex metallurgical by-products. The importance of preliminary mineralogical characterization is emphasized as a preliminary step for the success of the roasting. Stage selective roasting appears as an attractive and efficient route for the treatment of complex concentrates. Numerous examples will be given for confirmation of such thermal treatment.

Jan 1, 2006

By Russell James Hewertson

Since 1989 Air Products and Chemicals, Inc. has converted over 40 air fuel fired furnaces to oxy-fuel and air-oxy-fuel. Advances in burner design, flow control technology and operating experience have lead to improved performance with quicker melt times and lower costs. Metal recoveries are improved by faster melting and better furnace atmosphere control, allowing lower grade materials to be processed economically. The presentation will discuss the improvements made in recent years and review data from state of the art installations.

Jan 1, 2000

By Robert F. Jenkins

This document addresses the use of practical and basic engineering principles to develop a computer model for the analysis of the various issues which affect heat transfer in aluminum sidewell furnaces. These issues include furnace charge conditions, furnace operating conditions, furnace general arrangement, furnace combustion conditions, and furnace ambient heat loss. The engineering principles applied to this model were first put to test over 20 years ago. A prototype computer model developed 12 years ago has been in continuous use by Thorpe Technologies to determine the performance of sidewell furnaces for the aluminum industry. A new computer model has enhanced capabilities for more detailed performance analysis including regenerative and oxygen enriched combustion.

Jan 1, 2000

By Haotian Xue

A new process to extracted antimony directly from stibnite concentrate by reductive sulfur-fixation smelting in sodium molten salt has been presented. The influences of sodium salt content and composition, ferric oxide addition, temperature and time was investigated, respectively. The optimum conditions was determined as follows: W????: ??concentrate=40%, W??alt: ????concentrate =88.75%, WFe2O3 :Wconcentrate =55.13%, W??aCl: ????alt=40%, 1123K, 1h. Under above-mentioned optimum conditions, the average direct recovery ratio of antimony can reach 91.48%, and the main chemical composition of obtained crude antimony is Sb 94.31%, Fe 4.436%, Pb 0.502%, Au 0.0236%. In comparison to traditional antimony pyrometallurgical process, the smelting temperature of present process is reduced from 1423~1473K to 1123~1173K. During the smelting operation, SO2 emision can be avoided completely due to sulfur-fixation as FeS. Furthermore , S0 can be obtained when the molten slag is handled by water leaching with conditions of 323K, L/S=5/1, 2h.

Jan 1, 2014

By Bob Drew, Alfred Spanring, Kirschen. Marcus

"Increasing material conversion and energy efficiency, and decreasing carbon dioxide emission levels are crucial for sustainable production processes in the aluminum, cooper, and steel industries. RHI supports these targets by providing a diverse range of solutions including high quality refractory linings, optimum lining maintenance, and process improvements. In this paper examples are provided of process improvements and increased energy efficiency in copper refining, potential energy savings during electric arc furnace and ladle operations in the steel industry, and increased energy efficiency by improved heat transfer in anode baking furnaces in the aluminum industry. In all cases, RHI’s expertise in close collaboration with the customer resulted in an improved performance of the reactor lining and the actual high temperature process with a positive impact on the material conversion and energy efficiency and as a result a decrease in specific carbon dioxide emission levels.IntroductionRefractory linings play an important role in heat transfer during high temperature processes in for example the aluminum, copper, and steel production industries. Due to constantly increasing energy prices worldwide and the increasing demands for environmental and climate protection, improving the energy efficiency and decreasing emission levels of these energy intensive production processes is of significant importance. In this paper, the contribution of modern RHI lining technologies to energy saving measures and the corresponding reduction of specific carbon dioxide emission are described. The type of current refractory solutions for energy intense processes are illustrated with four examples: Optimization and increase of material conversion and energy efficiency in copper refining, energy saving potentials in both electric arc furnace and transport ladle operations in the steel industry, and heat transfer improvements during the carbon anode annealing process in the aluminum industry. These examples focus on particular production processes operating with a high proportion of recycled copper, steel, and carbon anodes. Increased energy efficiency directly decreases the specific energy related carbon emission levels whereas improvements to the metallurgical processes aim to increase material conversion efficiency and, therefore, decrease specific process related carbon emission levels. Significant energy savings can be achieved by maximizing the refractory campaign length through a combination of appropriate refractory material selection, grade zoning, correct installation, careful preheating, and effective maintenance strategies. Besides the efforts to improve the performance and energy efficiency of customer high temperature processes, RHI continuously promotes the development of new low emission carbon-containing refractory bricks and unshaped products."

Jan 1, 2008

By Hugo Cabrera-Real

This work investigated the chemical and mineralogical properties of CaO-SiO2-CrOx-CaF2- MgO slags. Synthetic slags were prepared and the effect of the slag basicity (CaO/SiO2) and MgO contents on the stability of the mineralogical species formed was analyzed. The morphology and composition of the slags were analyzed by XRD and SEM-EDS, whilst their chemical stability was evaluated by leaching with an aqueous acetic acid solution. It was found that in slags with CaO/SiO2 = 1, the main Cr-compound was MgCr2O4 spinel, which forms octahedron crystals. Small amounts of CaCr2O4 and CaCrO4 were also observed. It was found that increasing the slag basicity from 1 to 2 the compounds MgCr2O4 and CaCr2O4 were formed together with the Cr(V)-containing compound complex Ca5(CrO4)3F which forms hexagonal crystals. The results showed that the highest chromium concentration levels in the leaching liquors corresponded to slags with CaO/SiO2 = 2, probably owing to the formation of Ca5(CrO4)3F.

Jan 1, 2010

By Bowen Li

Copper vermiculite is a special nanomaterial with excellent antibacterial and antifungal performance. By means of ion exchange, copper vermiculite containing up to 5.8wt% copper was prepared. The chemical and mineralogical characterization of the material was investigated in this study based on the XRD, AAS, TEM and EDS analysis, as well as the calculation of crystalline parameters and crystal chemical formula. Cu2+ and Mg2+ have similar atom radius and same electrovalence. Correspondingly, the structure character of copper vermiculite is very close to that of standard Mg-vermiculite. Most of the CU21 may have occupied the interlayer cationic positions in the form of hydrate in vermiculite. However, some may have entered into octahedral coordinate positions. The values of au and bo of the copper vermiculite crystal cell have no obvious change compared to that of original vermiculite micropowder, but the Co value decreased slightly, which is desirable for the stabilization of the Cu2+ in copper vermiculite.

Jan 1, 2003

By Katsumi Ogi, Hiroto Uchida, Masamitsu Sato, Atsushi Itsuki

"(BTMSE)Ag(hfac) (BTMSE = trans-bis(trimethylsilyl)ethene) was chosen as a suitable precursor for the XeCl laser (308nm) MOCVD of Ag. Iso-propanol solution of (BTMSE)Ag(hfac) was used as a liquid source for the liquid delivery method, high deposition rate 9nm/min at substrate temperatures of 100°C and 120°C were obtained at the vaporizer temperature of 90°C. This deposition rate is three times faster than by conventional bubbling method and life of the source and reproducibility of the deposition were also improved. Electric resistivities of the laser deposited film shows significantly low resistivity of 10-6Q-cm compared to 1 o-3Q-cm of thermal MOCVD film. These results indicates that the laser MOCVD is one of the effective method for the preparation of the high quality silver film.IntroductionSilver films are a potentially important metallization material in electronic and photonic devises due to their lowest resistivity (1.6µ0-cm) among the metals, high optical reflectance and chemical stability. The MOCVD technique has advantages to sputtering or evaporation in the point of conformal growth and better coverage on sharp steps and narrow gaps[l-2]. For MOCVD application, silver precursors must have sufficient vapor pressure without decomposition at their evaporation temperature. To achieve stable precursor gas supply, liquid delivery of precursor material is promising[3-4] especially for materials that have not enough heat stability and high vapor pressure like silver complexes[S-10]. Several new silver complexes for MOCVD and UV irradiation effect to their MOCVD silver film quality were reported by same authors[5]. In this paper new solvent system for liquid delivery system of silver MOCVD were investigated to suite XeCl(308nm) laser MOCVD application."

Jan 1, 1998

By Sung Wng Kim

The binary antimonide compounds with the skutterudite structure have a potential for thermoelectric applications because of the high carrier mobility, high thermoelectric power, and relatively low thermal conductivity due to the complex crystal structure. However, the room temperature thermal conductivity of these skutterudite materials is as high as about IOW/mK with an estimated 80-90% contribution from the lattice thermal conductivity. Because the lattice thermal conductivity of related ternary skutterudite compounds can be substantially reduced due to the additional phonon scattering, a study of thermoelectric properties of these compounds is of interest. The binary IrSb3, ternary Ir1.xRuxSb3 and Ir(MxSb1.x)3(M=Ge, Sn) compounds were prepared by hot pressing of pre-reacted powders. We have measured the electrical resistivity, thermoelectric power, and thermal conductivity, in a temperature range from room temperature to 973K. The binary IrSb3 compound is found to have P-type electrical properties exhibiting a good Seebeck coefficient (up to 225µV/K around 773K), electrical resistivity(5x10-5Ohm M around 933K), and relatively low thermal conductivity(6W/mK around 950K). The lattice thermal conductivity, K[2] was calculated from the Wiedemann-Franz relationship.

Jan 1, 2002

By Vinay Kumar, Manis Kumar Jha, J. Rajesh Kumar, Archana Kumari, Rekha Panda, Jin Young Lee

Rare earth metals (REMs) play a significant role in the manufacture of permanent magnets, fluorescent lamps, catalysts, medicines, super alloys etc. Recently, China, which controls 97% of world trade in REMs, imposed restriction on its export. Consequently, the global demand of REMs is escalating and is expected to exceed the supply by 40,000 tonnes annually. Present review paper reports the flow-sheets of commercial processes based on pyro-hydro and hybrid techniques as well as systematic research for process development to recover REMs from primary and secondary resources. This review paper also reports the recommendation and future prospective to fulfill its demand and supply gap keeping in view environmental prospective.

Jan 1, 2014

By J. C. Riani

The release of heavy metals into the environment is increasing among others due to human activities such paint and pigment industries, tanneries, and metal finishing industries. Among metal releases, chromium is notable because this metal is carcinogenic. Thus, the aim of this work is to use an ion exchange system composed of one cationic resin column and one anionic resin column in order to adsorb the chromium (III, VI) from chromium electroplating effluents with the objective of recycling the water. The methodology consists of chromium adsorption tests using the ion exchange resins system with Purolite the 850 (polystyrene matrix, functional group quaternary amine) and Purolite C 150 (polystyrene matrix, functional group sulfonic acid). The contaminated solutions were passed through the columns with the assistance of peristaltic pump. Samples of the outgoing solution were taken in order to control the conductivity and pH and analyze the metals. The effects of the feeding outflow on the chromium adsorption were evaluated. The results show that the quality of the water collected at the end of the process is within the Brazilian standards about the discarding of toxic substances in the environment (CONAMA 357/05). This makes possible the recycling of water into the process and also its discharge in the rivers.

Jan 1, 2006

By Tetsuya Uda

Our recent achievements of rare earth separation technique[1,2] and new process idea for rare earth magnet recycling[3] are reviewed, (1) Binary chloride mixtures of rare earths were separated by a new selective reduction-vacuum distillation process. According to our experimental results, apparent separation factors were 8.1 for the Pr-Nd chloride mixture and 570 for the Nd-Sm chloride mixture. These values are much higher than conventional solvent extraction methods. (2) A study of recycling process of magnet sludge was carried out. The rare earths in the neodymium magnet sludge were extracted by chlorination with FeCI2, An activated carbon was used as a de-oxidation reagent Metallic iron in the sludge was not chlorinated because the iron monochloride is not stable, The extracted rare earth chlorides were easily separated from Fe-alloy and the excess of FeCh by vacuum distillation, 96 % of neodymium and 94 % of dysprosium in the sludge were extraeted into chloride phase, By the vacuum distillation, a mixture of neodymium and dysprosium trichlorides of 99.2 % purity was recovered, On the other hand, the rare earth chlorides can be converted to the corresponding oxides by a pyrohydrolysis reaction accompanied by a formation of HCl gas, The HCI gas can chlorinate metallic iron to FeCh, Therefore, a new recycling process for rare earth magnet waste can be realized as a chlorine circulation type process. During the process, only carbon and water are consumed and there are no toxic pollutants, Moreover, the obtained rare earth oxide can be directly used as raw material in the conventional oxide electrolysis process,

Jan 1, 2003

By James B. Pfeiffer

TETRA Technologies, Inc., has applied its HDSIM metals precipitation system to treat a waste stream containing scrubber blowdown and process water from a smelter operation. The combined stream contained cadmium, lead, selenium, arsenic and zinc, plus some iron and copper. Treatment requirements included meeting stringent mass flow limitations for specific heavy metals. The HDS ? system can reduce the arsenic from 600 ppm to less than one ppm. The process generates a dense sludge that can be reprocessed in a smelter, eliminating the liability associated with landfilling. Flow diagrams and process details are discussed.

Jan 1, 1994

By Jin-tao Gao

In order to recover Ti resource from titanium bearing blast furnace slag, a new technology to separate perovskite phase from CaO-TiO2-SiO2-Al2O3-MgO system by supergravity is researched. In the condition of gravity coefficient of 750g, treatment temperature of 1305°C and time of 20min, the significant layers appear in samples which are obtained by means of centrifugal treatment. Along the direction of the supergravity, the volume fraction of perovskite phase increases gradually, and the equivalent diameters of perovskite phase crystals increases with the area approaching to the bottom of the sample. It is indicated that TiO2 is enriched in the bottom of sample as concentrate with a recovery ratio of 74.05% by supergravity treatment.

Jan 1, 2014

By Shaohua Ju, Huang Chang-yuan, Lu Shuaidan, Peng Jin-hui, Wu Guoqin, Yaqian Wei, Zhang Li-bo

"The contrastive studies of microwave and conventional roasting copper residue from zinc hydrometallurgical was carried. The experimental results showed that the microwave roasting has the higher dechlorination rate in the same condition such as temperature, heat preservation time and atmosphere. When the samples with 100 mesh grain size, the Cl content turned from 14.27% to 1.33% and the dechlorination rate achieved over 90% at 400°C with 2h microwave roasting. And in the same conditions, the materials' dechlorination rate after conventional roasting just reached around 78%. The phase changes of the roasting process was investigated with X-ray diffraction analysis.IntroductionCl element can be accumulated gradually in the solution of Zinc hydrometallurgical system. When Cl content in electrolysis solution comes up to 100 mg/L, the stability of electrodeposits process would be severely affected [ 1]. It would not only accelerate the consumption of cathode and anode plate, elevate the power consumption, but also cause serious corrosion of device, increase production costs and lower the quality of electrolytic zinc [2]. Thus, C1- contained in the solution should be removed before electrodeposits."

Jan 1, 2013

By Carlos Carnurri

A characterization of mechanical properties of fire refined copper has been done in order to link ductility with oxygen content. The results show four different copper mechanical behaviours as temperature increases, where the oxygen con- tent, as Cu20 segregated, has a deleterious effect on ductility. It is concluded that until 500 ppm oxygen content, the fire refined copper could be rolled without remelting for deoxidation. Also a subsequent cold rolling could be done without intermediate annealing.

Jan 1, 1994

By Katsutoshi Inoue

The sulfuric acid leaching of spent hydrodesulfurization catalysts yields an acidic solution rich in rare metals such as molybdenum, vanadium, cobalt, and nickel in addition to aluminum. For the purpose of separating and recovering the rare metals from the solution, basic solvent extraction characteristics of the metals involved with commercially available acidic organophosphorus reagents like TR-83, PC-88A, PIA-8 and CYANEX 272 as well as aliphatic alpha-hydroxyoxime LIX 63 from sulfuric acid media were investigated in the present work. It was demonstrated that CYANEX 272, PIA-8 and LIX 63 possessed excellent selectivity for molybdenum and vanadium over the other metals at comparatively low pH. Further, recovery of molybdenum and vanadium from the total leach liquor by the selected extractants was discussed. Additionally, in order to achieve preferential separation and recovery of cobalt and nickel over an appreciable amount of aluminum from the raffinate obtained after recovering molybdenum and vanadium, a systematic investigation was conducted on synergistic extraction behaviors of the mixed solvents of LIX 63 in combination with a series of acidic extractants such as CYANEX 272, PIA-8, PC-88A, D2EHPA, TR-83 and OPEHPA for cobalt, nickel and aluminum. It was elucidated that all of these mixtures could exhibit a good synergistic effect for extraction of cobalt and nickel, and that the lower the pKa of the acidic extractants, the greater the synergism. Contrarily, the extraction of aluminum, was considerably suppressed by LIX 63. Effective extraction of cobalt and nickel away from aluminum was accomplished from the sulfate solution at low pH (1.0 - 2.5) with the mixtures. In particular, the mixtures consisting of LIX 63 and CYANEX 272 or PIA-8 appeared to be the most feasible and economic from an industrial point of view, yielding acceptable separation efficiency for cobalt and nickel over aluminum and .a low acidity requirement for stripping cobalt and nickel as well as negligible degradation of LIX 63. Aluminum can be readily recovered as sulfate salt from the raffinate obtained after recovering molybdenum, vanadium, cobalt and nickel as outlined above by conventional crystallization method.

Jan 1, 1995