Search Documents

By K. Ohmori, K. Takeya, S. Yoshizawa, A. Kawamoto, T. Ishikawa

"High performance Sm2Fe17N3 magnet powder is developed nitriding Sm2Fe17 alloy that 'is made using a reduction and diffusion method. Typical remanence, coercivity and maximum energy product of the fine powder are 1.40 T, 1.13 T and 323 kJ/m3, respectively. Decreasing samarium content, oxygen content and the amount of a-Fe are found to be the important factors to realize high-energy product.High performance injection molded Sm2Fe17N3 anisotropic magnet is also developed using the powder and an original binder system developed in order to mold at low temperature. Typical remanence, coercivity and maximum energy product obtained are 0.77 T, 0.78 T and 103 kJ/m3, respectively in the density of 4.77 Mg/m3The temperature coefficient of remanence is -0.07 %/K and that of coercivity is -0.54.%/K. The initial irreversible flux loss of the magnet that has a permeance of two is -5 % at 100 °C and the irreversible .flux loss of it is -4.4 % exposing it at 80 °C for 1000h.IntroductionSm2Fe17N3 alloy powder is expected to be very useful for a bonded magnet. The reasons are as follows. The magnetization is as large as the Nd2Fe14B alloy. Curie temperature is even higher than the alloy. The uni-axial anisotropy is comparatively higher than the alloy. Consequently it is possible to obtain high coercivity after just milling the powder and therefore possible to obtain high-energy product in a bonded magnet as it is realized in the SmCo5 bonded magnet. On the other hand, sintering is difficult because it will be decomposed into samarium nitride and a-Fe when heating it up to 500°C:"

Jan 1, 2000

By S. K. Wu, Ray Y. Lin, Sunil Annaji

Infrared joining of TiAI using aluminum foils as the filler material was investigated at temperatures between 1050 °C and 1350 °C in a flowing argon environment for times varying between 15 and 60 seconds. Using aluminum foils, the attempt was to form the Al3Ti phase in the joint as a result of reaction between Al and TiAI at temperatures above the melting point of Al. It has been found based on X-ray diffraction and TEM analysis that, Al3Ti, indeed is the product of infrared joining of TiAI using Al as the joining alloy. Al3 Ti was detected even in the joint processed at 1050 °C for only 15 seconds. Since the aluminum foil used in this study contains 27 at% Si, the t 2 phase in the Ti-Al-Si ternary system is believed to have also formed at the joint/base TiAI interface. Cross sectional studies on the joined specimens have shown different degrees of reaction depending on the temperature and time of joining. Micro hardness evaluations across the joint show that the hardness near the center of the joint is typically smaller than that near the joint edge next to the base material. However, as the joining temperature and time increase, the increment of the hardness at the center of the joint is faster than that around the periphery of the joint.

Jan 1, 1996

By W. Zhao

Several years ago, Reddy and Blander presented upriori model for calculating the sulfide capacity of binary silicate melts. It is modified now to apply to CaO-AlO 1.5 melts at different temperatures and compositions. Our predictions are in very good agreement with the available experimental data. From a comparison of binary calcium aluminate and calcium silicate systems, higher sulfide capacities are obtained in aluminate systems. The sulfur can be removed from hot metal more effectively by adding aluminate melts.

Jan 1, 1995

By Pengfu Tan

A thermodynamic model has been developed to model the desilverising process of lead by the addition of zinc during lead refining, whereby silver-zinc solid solutions are formed, and floats out of the dissolved zinc/silver in the lead bath. The solubility of silver-zinc solid solutions in lead decreases with falling temperature. A number of variations and modifications of the desilverising process are modeled, and applied to a wide range of silver contents in lead bullions in the industry.

Jan 1, 2005

By C. L. Lin

Transformation of linear grade distribution to volumetric grade distribution has been used to estimate the actual mineral liberation during wet, batch, ball mill grinding of a copper ore. The degree of liberation based on the multicomponent-multisize grinding liberation model using volumetric grade is lower than the apparent degree of liberation estimated from using King's linear intercept model.

Jan 1, 1987

By Michael S. Moats

As commercial copper electrorefineries look to expand their capacities by increasing their operating current density, the likelihood of anode passivation intensifies. To improve the industry?s understanding of the passivation phenomena, the role of anode composition was evaluated. While previous studies have focused on studying one impurity element at a time, this study was conducted using forty-four commercial electrorefining anode samples supplied by ten copper companies The passivation response of each sample was evaluated under accelerated galvanostatic conditions in synthetic copper electrowinning electrolyte at 65°C. This information allows for correlations between composition and passivation tendencies over a wide range of impurity elements and concentrations. It was found that selenium, tellurium, silver, lead and nickel accelerated passivation. It appeared that oxygen accelerated passivation when increased from 500 to 1500 ppm, but further increases did not have an effect. Arsenic was the only impurity found that inhibited passivation.

Jan 1, 2006

By Neal Schwartz, Robert De Saro, Richard Rosenthal, Ed Kear

"A Stack Melter has been installed and is currently operating at Lexington Die Casting. The Stack Melter consists of a 1 meter (3 foot) diameter refractory tube, 2 meters (7 feet) high. Specification ingots are continuously fed to the top of the melter and piled to nearly the top. A burner fires through the scrap which melts the lower portion and preheats the upper portion. As the lower portion is melted, it is drawn out and the upper preheated scrap falls to a lower level where it in tum melts. The molten metal is fed to one of two holding furnaces for eventual delivery to a casting machine.The Stack Melter's energy use is approximately 2900 joules/g (1,250 Btu/lbm), resulting in an overall energy savings of about 58%. This energy savings is brought about primarily because the flue gases preheat the scrap and the flue gas temperature is dropped to well under 528°C (1000°F)."

Jan 1, 2000

By Bruno Lebon, Koulis Pericleous, Georgi Djambazov, Mayur Patel

"High speed compressible jets are used in a number of steel-making applications. In the case of the BOF, a compressible oxygen jet reacts with a carbon-rich iron bath to reduce carbon levels and produce steel. The intensity of the process is governed by the speed of the jet and by the size and shape of the depression created in the metal and slag by the force of the jet, i.e. by the corresponding free surface. This is a difficult CFD problem, since there are compressible and incompressible regions in the flow domain, which need to be handled differently in a finite-volume (FV) pressure-correction scheme. Also, standard turbulence models do not account for compressibility, or the large difference in density between the cold oxygen jet and the hot reacting surroundings. Corrections are introduced to the k-E model to remedy this deficiency and the results are validated against experimental data. The compressible/incompressible boundary is handled through a transition region, based on Mach number.IntroductionThe deformation of a free surface by a compressible high speed jet is of paramount engineering interest, particularly for understanding the physical processes within a Basic Oxygen Furnace (BOF). In a BOF, a supersonic oxygen jet impinges on a molten iron surface, thereby creating a cavity. Oxygen penetrates the bath and removes carbon, resulting in low carbon steel [1].The challenges in modelling such a process lie in coupling a solution domain with distinct compressible and incompressible regions and in dealing with large density differences between the modelled gas and liquid. The modelling of compressibility within the jet is crucial, since the correct velocity profile in the jet is required to determine the cavity depth with accuracy."

Jan 1, 2012

By V. Bredykhin

The efficiency of scrap processing depends firstly on reliability of information about its chemical composition. The paper presents the results of the investigation and development regarding solid copper alloy scrap in the range of lump size 40÷300 mm. Nowadays the sorting of lump scrap is done by two methods: 1. Sorting according to metals and alloys is done at places of scrap generation, and further till metallurgical processing each lot has its "certificate"; 2. Hand sorting of scrap is done according to the marks on solid items in special shops using proximate analyzers or manually by experienced workers. This sorting process is labor - consuming low efficient and involves mistakes. The informational method is a promising trend in the copper scrap sorting. The method is direct, i.e. as a result of sorting the chemical composition of each scrap lump or main elements is determined, and assured data of qualitative and quantitative composition are received.

Jan 1, 2006

By M. A. Vera

This paper proposes a simple two-parameter model for the typical inverse relationship between recovery and flotation concentrate grade. The model is based on the mineralogical limitations imposed by the material properties. One parameter (R*) describes the proportion of metal content which is floatable, and the other (b) is the rate at which the fastest floating particles are being contaminated by the other less valuable particles present in the mineral system. One significant feature of the recovery-grade curve is that initial recovery (i. e. R ? 0) is at the purest attainable mineral grade, (but as recovery rises the cumulative grade of the concentrate tends to the feed grade. The ideal recovery-grade curve for a particular mineralogical system can be obtained by release analysis: the release analysis curve determines the maximum or limiting separation efficiency. The model proposed in this work is similar to the linear recovery - cut-off grade model of Dell (1), but has the advantage of describing the whole curve.

Jan 1, 1999

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been investigated on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27 degrees between each tuyere, and five side tuyeres with an angular separation of 22.5 or 27 degrees between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

By S. G. Galbraith

We have used the principles of supramolecular chemistry to develop reagents to transport metal salts. These reagents have separated charged "compartments" which recognize a metal cation and its attendant anion(s). They are easy to manufacture as they are structurally related to the commercial hydroxy-oxime extractants for copper. Efficient protocols for loading and stripping of these extractants depend on the novel feature that they bind the metal salt in a zwitterionic form of the ligand. Transfer of the phenolic protons to the pendant amines generates the charged "compartments" to accommodate the metal cation and its attendant anion(s). This paper focuses on how these types of reagent can be used to recover base metals from sulfate and chloride media in flowsheets in which solvent extraction effects separation and concentration operations, interfacing between conventional leach and electrowin/reduction processes. Work on the development of reagents that have high selectivity for metal chloride/sulfate transport, convenient stripping protocols and appropriate hydrolytic stability will be described.

Jan 1, 2003

By H. Cui

Rapid technological development has caused an increase in the demand for rare earths. Ancylite, a strontium rare earth carbonate, is a potentially significant source of rare earths. In this research paper, essential aspects of the magnetic separation and flotation processes for Bear Lodge ore are presented. A flowsheet is proposed based on an optimization of the variables and flotation simulation. The economic feasibility of the proposed processing operation is analyzed.

By Shadia J. Ikhmayies

"Cadmium telluride (CdTe) is a very interesting material that has many applications. Thin films of p-type CdTe can be used as the absorber layer in the heterojunction CdS/CdTe thin film solar cells in which n-type cadmium sulfide (CdS) works as the window layer. A review of the photoluminescence (PL) spectra ofp-type CdTe thin films prepared by different techniques was performed. The presence of defects and impurities such as oxygen and chlorine influence the PL spectrum. Copper and other dopants change the PL spectra and enhance the defects band. Chemical-heat treatment especially with CdCh is known to improve the quality of CdTe thin films because it decreases the Cd vacancies and quenches deep traps, so it enhances the PL signal. A discussion of chemical-heat treatment especially with CdCh, the effect of the ambient atmosphere, and that of the measuring temperature is performed.IntroductionCadmium telluride (CdTe) is a II-VI compound semiconductor that has a cubic zincblende (sphalerite) structure with a lattice constant of 0 A4~11]. Other than all of II -VI semiconductors, CdTe can be made both n- and p-type. But due to self compensation it is not easy to get p-type CdTe films [2]. Polycrystalline CdTe thin films are interesting because they have a lot of applications. Most of the problems associated with the use of these films are attributed to inhomogeneity, self-compensation, and the difficulty of forming a stable and lowresistivity ohmic contact [3]. CdTe technology has been established for a large number of applications, including solar cells, optical and nuclear detectors, and thermal- and radiationimaging devices [3]. At present, the highest demonstrated conversion efficiency for a CdTe based heterojunction (ID), with CdS as a window layer, is 16.5% [4, 5]. CdTe thin films can be prepared by different experimental techniques, such as thermal evaporation [l], electrochemical deposition (ED) [3], close-spaced sublimation (CSS) [3, 4, 6], physical vapor deposition (PVD) [3], chemical molecular beam deposition (CMBD) [7], and close space vapor transport (CSVT) [8].The objective of this paper is to make a review of the photoluminescence (PL) spectra ofp-type CdTe thin films prepared by different techniques and discuss the factors that influence the PL spectra. The composition of the film is very interesting in determining its PL spectrum. Different kinds of defects, impurities and dopants have their finger prints in the PL spectrum. Deposition techniques and deposition parameters such as the deposition temperature and ambient atmosphere also have their influence. Heat and chemical treatments which are known to improve crystallization and reduce the defects change the PL spectrum."

Jan 1, 2013

By K. B. McTaggart, G. Owusu, P. J. Merrin

"This study was conducted at Hudson Bay Mining and Smelting's zinc electrowinning tankhouse to determine the effects of varying levels of antimony and continuous gelatin addition on current efficiency. The levels of antimony and gelatin were varied from 0.012 to 0.030 mg/l and 0 to 10 mg/ll2 • 31 respectively, based on neutral ZnS04 electrolyte. A non-linear mathematical model relating current efficiency with antimony and gelatin was produced. The optimum operating point for gelatin was 6.5 mg/l. On the other hand the current efficiency increased with decreasing antimony levels. An interaction term between gelatin and antimony is present but is not significant enough to improve the ability of the tankhouse to handle purification upsets in antimony. Individually, the current efficiency was linear (decreasing) with antimony, and parabolic with gelatin concentration. However, at low antimony concentrations stripping of the cathode sheet was difficult. IntroductionThe zinc electrowinning tankhouse at Hudson Bay Mining and Smelting was designed in the 1930's and consists of 120 rows with each row containing ten cells. This system cascades acid from cell to cell In a row, with neutral zinc sulphate solution added to each cell through manually controlled spigots. Animal glue additions are made manually three times per day by operations personnel. The problem with this type of cell design and operation is that feed solution flows and composition can vary from cell to cell and from row to row due to the large number of manual control points. A new system which reduces the number of manual control points was designed and tested to determine if improvement in control of cell conditions would affect current efficiency. This system mixes spent acid, neutral ZnS04 electrolyte and reagents (gelatin, antimony and strontium carbonate) in a separate mix tank, ensuring that all cells receive a uniform feed solution. Gelatin was used in the test system instead of animal glue (which is presently used) because of the poor solubility and supply of industrial animal glue. The study reported here is the first in a series of experiments designed to justify the need to modify the present cascading cell feed system (Figure 1) to the proposed feed system (figure 2)."

Jan 1, 1997

By G. C. Yao

Iron and silicon impurities can form needle and branch shape intermetallie compounds in molten aluminum when there is no manganese. It is difficult to separate them from molten aluminum by electromagnetic separation. The Fe-Si-AI and Fe-AI intcrmetallic compounds were transformed into Mn-Fe-Si-AI and Mn-Fe-AI compounds by the addition of manganesc into molten aluminum, In molten aluminum the morphology of these intermetallic compound particles is lumpish and spherical. Migration resistance of these impurity particles is small, which is beneficial to separation. FeSiMnAl4 and FeMnAl6 arc paramagnetic. These impurity particles can be moved by magnetic force and can be separated from the molten aluminum.

Jan 1, 2003

By G. C. Yao

Iron and silicon impurities can form needle and branch shape intermetallie compounds in molten aluminum when there is no manganese. It is difficult to separate them from molten aluminum by electromagnetic separation. The Fe-Si-AI and Fe-Al intermetallic compounds were transformed into Mn-Fe-Si-Al and Mn-Fe-Al compounds by the addition of manganese into molten aluminum. In molten aluminum the morphology of these intermetallic compound particles is lumpish and spherical. Migration resistance of these impurity particles is small, which is beneficial to separation. FeSiMnA4 and FeMnAI6 are paramagnetic. These impurity particles can be moved by magnetic force and can be separated from the molten aluminum.

Jan 1, 2003

By Gaifeng Xue, Jingxuan Zhou, Shangchao Liu

"Both COD and TOC can characterize organic pollution of coking wastewater. In theory, there is a linear correlation between these two indicators. After continuous monitoring TOC and COD of coking waste water, linear regression relationship between of these to indicators was studied with the use of mathematical statistics. And conversion equation between these two indicators was established, and using t-test method for significance testing. The results showed that the linear relationship of COD and TOC was significant. Also interval estimation of equation slope and intercept were given in the condition of 95% confidence level. A linear regression equation established can be used to indirectly convert TOC to COD with high precision and accuracy.IntroductionBoth chemical oxygen demand (COD) and total organic carbon (TOC) are measure of the degree of characterization for organic pollution of water bodies. The current COD standard analytical methods is Potassium dichromate titration method [1] . there are some disadvantages in this method, such as only part of organic matter in the water bodies being oxidated, the refluxed steps, a long time needed for each measurement, high cost. It is the most important that sulfuric acid silver and mercury sulfate reagents used in the measurement may easily lead to secondary pollution. In contrast, the measurement of TOC is by the method of combustion or Photocatalytic Oxidation. The result could be easily got from the instrument. There are some advantages in this way, such as easy operation, short time and little expenses for each measurement and no secondary pollution 121• In addition, the measurement of TOC has higher degree of precision and accuracy than the measurement of COD both in the determination of calibration standards and actual samples. The meaning and contrast of TOC and COD are listed in the table 1."

Jan 1, 2013

By Tiezheng Li

Keywords: Laminate Composites; Mechanical Behavior; Damage Evolution The mechanical performance of Ti-6-4-Al3Ti metal-intermetallic laminate (MIL) composites synthesized by a reactive foil sintering technique was evaluated. Crack morphology of untested Ti-6-4-Al3Ti MIL composites has been characterized by optical microscopy. Mechanical tests were performed on Ti-Al3Ti metal-intermetallic laminate (MIL) composites and pure Al3Ti, and the principal mechanisms of damage initiation and accumulation were identified experimentally. The elastic properties and anisotropy of the laminates were calculated and successfully compared with Resonant Ultrasonic Spectroscopy (RUS) measurements. The effect of residual stress on the fracture toughness of the Ti-6-4-Al3Ti MIL composites was analyzed.

Jan 1, 2005

By B. Nowak

For sources with an iron-to-vanadium ratio of far above 1, it is proposed to leach in acid and to oxidize under autoclave conditions. During this oxidation process, it is experimentally shown that divalent iron contained in this solution will be oxidized to trivalent iron, whereas free acid contained will be consumed by this reaction. In case no acid is present or already fully consumed, a solid consisting of ferric compounds and an iron-vanadium-co-precipitate will form that can be filtered from the solution. If choosing the right reaction conditions, this filter cake has an iron-to-vanadium ratio of close to 1, whereas the liquid remainder is almost vanadium free. This precipitate, identified as FeVO4, 1.1 H2O, can be processed by conventional technologies such as caustic leaching, or probably salt roasting or reduction with aluminum, yielding common marketable products.