Search Documents

By D. J. Goodwill

BHP Copper operates a 3,400 tpd dry concentrate, single burner, Outokumpu flash smelting furnace (FSF) at their San Manuel copper smelter in Arizona. The very fine (-325 mesh), dry concentrate is fed to the burner from a 550 metric ton (nominal) capacity furnace feed bin via two drag chain feeders. During the 10-year history of the furnace, operations have been plagued by serious flooding problems. The fine concentrate sometimes becomes aerated during discharge from the bin and flows like a fluid at very high uncontrollable rates to the burner. This results in upset conditions at the concentrate burner leading to poor furnace metallurgy. This paper will examine the problems of uncontrolled feed from the furnace bin (i.e. flooding), and' instantaneously feeding a flash smelting burner. It will show that a drag chain is a poor choice of feeder when high rates are needed, and that drag chains always produce a funnel flow pattern in a bin. BHP's drag chains cause narrow diameter, high velocity flow channels within the stored material. Consequently, there is insufficient residence: time for the concentrate to fully de-aerate before discharge, hence flooding occurs. In addition to the flooding problem, drag chains create a pulsating flow to the concentrate burner due to the tendency for material to slough off in discrete chunks at the discharge end of the slow moving chain conveyor. During the scheduled FSF rebuild in May 1999, BHP intends to remove the drag chains, modify the bin to a mass flow design and to use STAMET® multi-disc feeders to accurately and instantaneously control the rate of discharge from the bins. Air slides will be used' to convey the concentrate to the burner.

Jan 1, 1999

By Takashi Nagai, Hideaki Sasaki, Masafumi Maeda

"The production of solar cells is increasing dramatically and the shortage of polycrystalline silicon for these cells has become a serious problem, making development of a low-cost production process for solar grade silicon essential. An electron beam melting technique is known to be effective for the removal of phosphorus from molten silicon. Although the phosphorus is removed by preferential evaporation in this process, the rate of removal is not sufficient, and its improvement requires thermodynamic information on phosphorus in the molten silicon. In this research, the vapor pressure of phosphorus in equilibrium with a siliconphosphorus alloy was measured by double Knudsen cell mass spectrometry with a system blowing gas into the Knudsen cell. The activity of phosphorus in silicon, the Gibbs energy change of the dissolution of phosphorus in silicon, and other factors were estimated from the results. Using these data, we provided guidelines on how this process can be improved.IntroductionSolar energy is in great demand since it is inexhaustible and cleaner than that from conventional energy resources. Silicon is the material most widely used to convert solar energy into electricity. Figure 1 shows the recent production of solar cells. High purity silicon for solar cells, namely solar grade silicon (SOG-Si), has been commercially supplied mainly from off-grade high purity silicon in the semiconductor industry. However, production of solar cells has increased rapidly in recent years, and the shortage of SOG-Si has become a serious problem, so that a new processes which can produce SOG-Si economically are required.Directional solidification was applied to remove transition metal elements such as Fe or Ti by segregating them from the remaining melt. However, such solidification is useless for phosphorus because the segregation coefficient of phosphorus is nearly unity. Numerous approaches have been made in an attempt to produce a resource of low cost SOG-Si from metallurgical-grade silicon (MG-Si). [1,2]"

Jan 1, 2012

Bath smelting options for recovering valuable metals from jarositic residues containing 22-28% lead and 16-30% sulphur obtained from pressure leaching zinc-lead-copper bulk concentrates were investigated using thermochemical computations and crucible-scale experiments. Direct fuming of lead and zinc from a slaglmatte bath at 1250-300°C was demonstrated successfully. Up to 93% of the lead was recovered in the fume and steady-state recoveries of zinc were predicted in the range 82-95% under these conditions. The energy required for the fuming reactions was supplied by partial combustion of the fuel, added as char, with air. An important feature of the process is that the recoveries to the fume are not significantly affected by changing: the fuel:air ratio over a wide range. Thermodynamic computations, confirmed by experimental results also showed that the presence of a matte phase is not essential for high recovery of lead and zinc to the fume. Operating conditions which produced a matte ensured that about 70% of the silver and 80-90% of the copper were recovered into that phase. Approximately 98% of the arsenic in the residue was fumed. In the absence of matte the slags contained high arsenic levels (260-330 ppm) but low arsenic (20-60 ppm) levels were achieved when matte was produced.

Jan 1, 1994

By Milton Manrique, Edgar E. Vidal, Patrick R. Taylor

"Ultrafine zirconium carbide powder has been synthesized using zircon concentrate and methane in a thermal plasma reactor. The effect of several experimental variables, such as power used and zircon particle size, on the conversion has been studied. A thermodynamic analysis of the possible reactions and stable compounds was performed. A mathematical model that describes the in-flight decomposition of zircon particles was developed based on a description of the temperature and velocity profiles calculated in the reactor. It was shown that the formation of zirconium carbide from zircon and methane is thermodynamically possible. Complete 'vaporization of zircon in the reactor is predicted when the particle size is below 45flm and the effective power entering the reactor is 15 kW. The powders were collected and characterized by XRD, SEM, TEM and chemical analysis using ICP. Results of the product analysis indicated the presence of zirconium carbide, zirconium oxide, silicon carbide and silicon oxide.IntroductionIn recent years there has been an increased interest in the production of nanometric sized powders of ceramic materials for use in advanced materials applications. One possible method to produce these powders is with a thermal plasma reactor, which offers high temperatures and fast quenching rates. This technology has been called - Thermal Plasma Synthesis - [1].Zirconium Carbide (ZrCx) has typical properties of transition metal carbides: elevated hardness - between alumina and diamond - a high melting temperature of 3420°C and high chemical stability at room temperature [2]. ZrCx has a Bl crystal structure with deficiencies in the number of carbon atoms in the cell with x between 0.6 and 1 [3]. Different methods have been used to produce ZrC, one method is by direct reaction of zirconium hydride or halide with carbon. Other methods used are direct reduction and carburization of zirconium oxide (Zr02) and reaction of metallic zirconium with a caburizing gas such as acetylene [3]. Recently small films of ZrC have been obtained using a sputtering device [4,5]. ZrC has been used in nuclear plants as a low neutron absorbing and high mechanical resistant refractory material and also as a constituent in cathodes made of UC-ZrC [6]. It is also used in the form of tubes, boats and crucibles to handle molten metals and as part of electronic devices used for thermoionic transducers. Recently ZrC has been used along with zirconium diboride (ZrB2) to produce composite materials [7,8]."

Jan 1, 1996

By G. A. Irons, G. S. Hanumanth

A three-dimensional mathematical model for the electric furnace of Cominco's Kivcet process was developed to compute the electric field intensity, power dissipation, temperature and velocity distributions in the furnace. A number of simulations of the electric furnace operation were carried out for various electrode immersion depths and electrode currents. The results showed that the current penetrated the bullion layer, generating high current densities in a layer approximately 0.3 m thick located in the slag/bullion interface region. An increase in the electrode immersion depth increased the furnace power as well as slag temperatures, and generated more vigorous bubble stirring and thermal homogeneity in the slag. For a given applied current, the computed power was in reasonable accord with the measured power input. The calculated temperatures were in rough agreement with the tapping temperatures of slag and bullion.

Jan 1, 2000

By Fuxing Yin, Akira Sato, Yoshiaki Ohsawa, Kohji Kawaharai

"INCRAMUTE alloy (nominally 45Mn-53Cu-2Al wt. %) has a specific damping capacity as high as 0.4, through a solid-solution and aging treatment. The damping behavior of the alloy is highly temperature-dependent and shows a peak near room temperature. The inadequate strength in the high damping condition restrains the practical application of the alloy, as structural components. Ferromagnetic MnB particles are dispersed in the alloy during induction remelting the matrix alloy in an argon atmosphere. Surface modification of the MnB particles by mechanical alloying (MA) and suitable control of the addition process cause a homogeneous distribution of MnB particles in the alloy. In the composite containing 2 wt. % MnB particles, temperature dependence of damping capacity is improved, and higher damping capacity is still retained in the temperatures over 60 °C. Meanwhile, the Young's modulus and tensile strength were also increased by about 20%. The roles of the MnB particles in improving both damping behavior and mechanical properties were also discussed.IntroductionMany viscoelastic materials, such as rubbers, polymers and plastics, have the superior ability to damp vibration and noise. However, in the applications as structural materials the high damping capacities of materials are pursued upon the satisfactory mechanical properties, especially those at elevated temperatures. Damping alloys are finding more and more applications in structures where noise and vibration ·should be ·eliminated. Specific damping capacity (SDC), defined as the ratio of the energy dissipated to the maximum vibration energy stored per cycle, is usually used to evaluate the damping capacity of alloys. INCRAMUTE damping alloy, developed by the International Copper Research Association, Inc., has a nominal composition of 45Mn-53Cu-2Al in weight percent. The high damping· microstructure of this alloy is obtained through the solution treatment at 820 °C followed by a water quench and aging at 400°C for 10 hours followed by cooling to room temperature [1]. With the heat treatment, a SDC peak ·vs. temperature of as high as 0.4 was observed in the alloy at the strain amplitude of about 10-3 while a tensile strength of about 500MPa was sustained."

Jan 1, 2000

By Waraporn Piyawit

Grinding sludge from the sintered neodymium-iron-boron (NdFeB) magnets production process was enriched with critical rare earth elements (neodymium, dysprosium and praseodymium), which can be up to 30% in the magnets. The demand of NdFeB magnets are simultaneously growing. Therefore, rare earths recovered from waste residue would reduce the demand of rare earth elements from primary sources. In this study, the feasibility of recycling rare earths through a hydrometallurgical process was investigated. The selective leaching of Nd from grinding sludge can successfully raise the rare earths concentration to 70%. The necessity of an oxidation pretreatment to improve the selectivity between Nd and Fe will be described.

By Romeo U. Pagador

After privatization in 1999, PASAR Corporation initiated a plant modernization program to optimize the performance of the smelter by increasing plant availability. This initiative required operational adjustments to the converting and anode furnace procedures, to support the higher throughput in the flash furnace, while continuing to meet government environmental regulations. The major shift in production direction was to eliminate the 30-35 day maintenance shutdown every two years, and replace it with a 15-day shutdown. This paper discusses the changes implemented in the converter and anode operation that have resulted in an increase of 10% in flash furnace throughput, an 18% increase in blister output, to 170 tonnes per cycle, and a converter campaign tonnage increase of 10%. Since privatization, PASAR has instituted a series of ?management of change? programs that have facilitated an industrial cultural change needed to achieve the company?s vision, mission and strategic goals.

Jan 1, 2005

By Tsisana Gagnidze

A processing of technogenous wastes, which involve a gold-containing sulphide minerals, is a potential source to supplement the gold reserves. Hence, searching of ecologically safe and economically reasonable methods for processing of gold-containing technogenous wastes is a topical problem. To increase a parameters of gold extraction and to simplify a technology of the processing of above-mentioned wastes of sulphide minerals, an investigations have been carried out in the direction of the use of the method of electrochemical leaching without any preliminary processing of the mineral. It was established experimentally that an introduction of nitrogen containing organic additive into chloride solution favours to reduce a Red/Ox potential of the solution from 0,8÷1,2 V to 0,35÷0,5V, which permits to conduct the process of direct electrochemical leaching at ?soft? oxidation regimes at temperatures 20-300C C without an environmental contamination by molecular chlorine and with a high degree of a gold extraction up to 80-90%.

Jan 1, 2008

By A. K. Kyllo

The use of Composite Furnace Module cooling systems has been shown to give improved refractory performance in a number of above bath locations in WMC flash furnaces. To test the behaviour of modules in contact with a melt, a set of instrumented modules have been installed in the reaction shaft of a. nickel flash furnace. The location was chosen to provide a suitably harsh environment to ensure rigorous testing, while still allowing relatively easy access for module installation. The modules were continuously monitored to provide information on the module performance, as well as the temperature in the shaft itself. The shaft temperature showed significant transient behaviour, which resulted in heat fluxes through the modules ranging from 10 to 92 kW m-2. The modules were capable of handling the highest heat flux with no risk of the coolant boiling. This paper details the design and operation of the modules over a period of seven weeks.

Jan 1, 1999

By Xian-Dong Zhou, Guo-Sheng Sun, Jianzhong Luo, Hong-An Guan

"Oxygen utilization rate of the pretreatment process which adopts biological contact oxidation method for slightly polluted supply water is relatively low, less than 10%, usually lower than 3%. So the aeration amount is not determined by calculated value of oxygen demand when doing process design, but by the ratio of gas and water. The aeration way of the biological pretreatment process for slightly polluted supply water was introduced in this paper. In the foundation of the principles of mass transfer kinetic theory and experimental data, the change law of DO (dissolved oxygen) and ammonia in the aeration tank was analyzed to explore aeration method which will help to improve the overall effectiveness of handling capacity.IntroductionThere are many kinds of filler used in the biological contact oxidation process, such as flexible solid filler, composite filamentous filler, powdery clay filler, particle ceramic filler and so on. Regardless of the different forms of filler, there are a couple of common points in the function of the aeration[1,2]: (1) The aeration process in biochemical tank not only provides adequate oxygen for the biological reaction, but also plays as a role of stirring water; (2) Biochemical reactions mainly happen in the upper reaches of tank, but seldom at down-streams.This paper, from the perspective of changing aeration way, discussed the feasibility of improving the effectiveness of biochemical reactions without increasing aeration amount, which would have some leading significances for the operation and management of similar projects."

Jan 1, 2008

By Adriana de Aquino Soeiro da Silva, Joao Alves Sampaioa, Luiz Carlos Bertolino, Francisco Manoel Garrido, Marta Eloisa Medeiros

"Brazil has a large agricultural potential and its production success is related to the chemicaland physical soil characteristics. Therefore, the demand in the use of a great quantity offertilizers to compensate the low amount of nutrients in the soil includes about 40% of foodproduction costs. In order to develop economical alternatives to traditional fertilizers, rockswith potential use in agriculture will be studied. In this work the potassium rock, a greensandslate, will be chemically and structurally characterized for the development of a potassiumthermophosphate. This alternative fertilizer will be obtained based on a fusion of a ponderedmixture of potassium, magnesium and phosphate rocks to be applied in the Brazilianagriculture. Preliminary characterization results indicate that the greensand slate presents ahigh percentage of glauconite, quartz and micas.Keywords: Potassium thermophosphate, alternative fertilizers, greensand slate.IntroductionBrazil has a great agricultural potential and its production success is closely related to thesoil's chemical and physical characteristics. However, the country's soils present lownutrients content and high acidity due to weather conditions. Thus, the use of a high amountof fertilizers makes up for the soils' lack of nutrients and accounts for 40% of food productioncosts. Therefore, research on obtaining new alternative fertilizers is a constant worry due tothe increase on food demand [ 1].The lack of raw material for the preparation of NPK fertilizers in Brazil is a concern and theissue of potassium fertilizers a priority. Such a fact is because in 2008 only 608.000 tons ofKCl were produced, corresponding to just 10% of the Brazilian necessity. Thus, the use ofrocks as agricultural nutrients can contribute to reduce the need for industrial fertilizers.This way, the development of a new agricultural raw material originated from a rock thatalready exists in the country's soil is of great importance for the mineral and agriculturalsectors."

Jan 1, 2011

By Isabela Leao Amaral da Silva, Felipe Perisse Duarte Lopes, Alice Barreto Bevitori, Sergio Neves Monteiro, Ruben Sanchez Rodriguez

"The fibers extracted from the stem of the ramie plant are among the strongest natural lignocellulosic fibers with a potential to be used as reinforcement of polymer matrix composites. Characterization of the ramie fiber has recently been conducted for its physical and mechanical properties. However, the effect of increasing temperature on the ramie fiber behavior has not yet been fully investigated. Therefore, the objective of this work was to perform a thermal analysis on ramie fibers with different diameters within the naturally found range of practical interest. The analysis was conducted by thermo-gravimetric, TGA and DTG, as well as differential scanning calorimetric, DSC, techniques. It was found that the ramie fibers present thermal stability up to 200°C and then suffer a sharp deterioration between 300 and 500°C, resulting in characteristic peaks.IntroductionSince the middle of last century, polymer composites have substituted many conventional monolithic materials in applications ranging from aerospace to sport [l]. The main advantages of these composites are the low density and flexible properties specially using fiber as reinforcement to suit the mechanical performance requirements [2]. These are usually high strength and stiffness requirements that could be reached with synthetic fibers such as glass, carbon and aramid fibers. In recent years, however, the use of synthetic fibers is being questioned in terms of problems caused to the environment. In fact, as non degradable material, synthetic fibers are associated with long term pollution when discarded. Moreover, the expended energy for fabrication and processing can be related to relatively large amounts of C02 emissions and represents a contribution to global warming [3]. Glass fiber, in addition, is toxic and cannot be incinerated as a waste in thermal power plants [ 4]. Possible substitutes for glass fiber are the natural fibers. Many natural fibers are today being considered as viable alternatives to replace glass fiber as reinforcement of polymer composites. In particular, some natural lignocellulosic fiber extracted from plants present a real potential for this replacement [2-8]. Their comparative advantages are lower density and reduced cost as well as renewability, biodegradability, recyclability and neutrality with respect to C02 emission [3]."

Jan 1, 2011

By Zuomei Jin

A laboratory study was conducted on the separation of Zn, Pb, Cu and Ag from a finely dissem-inated interlocked silver-rich multimetal sulphidc ore. These are often difficult to separate from each other by flotation. The thermodynamic calculations of Zn-S-O, Cu-S-O systems at different tem¬peratures were presented on predominance diagrams. Based on these diagrams the optimum temperature and gas composition were selected for roasting. The results of separating Zn, Cu from calcine by neutral leaching and acid leaching were found to be satisfactory. The distribution of silver in the roasting and leaching processes were tested. A flow sheet was proposed.

Jan 1, 1993

By M. El Ganaoui, P. Bontoux

"A computational model to investigate solid/liquid phase change transitions for binary alloy under directional solidification is presented. Conservation equations are developed by using an homogeneous formulation. A second order accuracy method of time and space based on finite volume approximation has been evaluated by comparing results to spectral solution for time-dependent solutal convection developping in a melted alloy. For extended model to solid/liquid interface effects time amplification of solutal perturbation injected near the interface is described before considering solutal convection is melt.IntroductionThe enthalpy method gives a front fixing approach for energy equation without introducing coordinate transformation. The interfare position is recovered a posteriori [1]. A number of authors have extended this approach so as to include the convection phenomena within the two phase 'mushy region' [2, 3, 4, 5, 6].We have developed a time-dependent enthalpy-porosity formulation for directional solidification [4, 6, 8]. The interaction between solid and liquid phases is modelised by a Darcien type force in the phase change area. The behaviour of the melt is similar with the flow of an incompressible fluid in a porous medium. This force is proportional to the relative phase velocity. It corresponds to a damping force depending on the anisotropic permeability of the 'mushy zone'. The permeability depends on the liquid fraction and on the size of·solidification microstructures. An informative discussion of a new slant on the general approach of continuum mechanics needed to analyze the formation of mushy zone is given in [12]. The method is extended to the presence of species diffusion: the solutal Stefan condition which expresses the solute incorporation or rejection across the interface is accounted implicitly in a species equation valid in all the domain [14, 15]."

Jan 1, 2001

By M. Drozd

Multi-use pad operators require an efficient and economic method to destroy cyanide in their process residues so new material can be stored on the pad and leached. Operators of the dedicated or single-use pads require an effective cyanide destruction method for pad closure. Cyanide destruction can be accomplished by utilizing oxidants such as hydrogen peroxide or calcium hypochlorite, or by utilizing ferrous sulfate which sequesters the cyanide in strong acid dissociable complex. Ferrous sulfate can be the preferred method of cyanide destruction because it is a less costly chemical, reaction rates are almost immediate and unlike oxidants, it can penetrate the total depth of a pile without being destroyed by side reactions. Literature indicates that the (Fe(CN)6)-4 com~lex is produced slowly but it appears that complexes such as Fe(CN)4(H20)2-or Fe(CN)4(OH)2)-4, are formed quickly and should have no U.V. sensitifity, unlike (Fe(CN)6)-4. Stoichiometry of the testwork indicates that Fe«CN)4(OH)2)-4 complex may be the species formed. The usage of ferrous sulfate has the advantage of being able to bring ~ level down that divalent metal ions such as Cu++, Cd++, Hg++, Pb++ and Zn will form insoluble complexes and precipitate from solutions does not destroy weak acid dissolvable complexes and can leave a heavy metal problem behind after cyanide destruction.

Jan 1, 1990

By Igor Rojkovic

The most important uranium mineralization in the Western Carpathians occurs in the Permian rocks. Low grade stratiform uranium mineralization was formed during the Permian due to adsorbtion and reduction by organic matter, titanium oxides, iron hydroxides, pyrite and clay minerals. During the Alpine orogeny uranium (± molybdenum and copper) remobilized stratabound ores were formed. Dominant ore minerals are uraninite, U-Ti oxides, molybdenite, pyrite and chalcopyrite Two generations of ore minerals are reflected by their textures and chemical composition.

Jan 1, 1995

By H. Kaffash

Ferromanganese is a ferroalloy with high manganese content which finds many uses for example as deoxidizer in steelmaking industry. However, there is very little data on the dissolution rate of carbonaceous materials in Mn containing metals. In this paper, the kinetic analysis of carburization reactions is investigated for Mn–Fe alloys. Dissolution rate of graphite in pure iron and four different alloys with 10 wt%, 40 wt%, 60 wt% and 85 wt% manganese at 1823 K was studied. Results showed that the dissolution rate of carbon from graphite increased with increasing time for all alloys. The dissolution rate constant increased with the increasing manganese content from 6.5 × 10−3 cm/s for 0%Mn to 23.6 × 10−3 cm/s for 85%Mn.

By Andrzej Szymanski

Recent developments in medicine have stimulated activities that? involve mineralogy. They include inplantation of inorganic and organic parts into bones and soft tissues, and uses of elements as basic stimulators for the human body. In addition contamination of the environment has increased the concentration of sane elements in food. Consequently f both the environment and food structure vary with geographical regions and influence human health. These activities in medicine have created the new fields of biomineralogy and of biogeochemistry as activities for the future.

Jan 1, 1989

By Zhan Jing

Keywords: thermodynamic, Ni-Co alloy powders, composition, fibrous The mathematics model of Ni(II)-Co(II)-C2O42?-NH3?H2O-H2O of thermodynamic equilibrium system has been developed theoretically according to the law of conservation of mass and the law of simultaneous equilibrium, and the logarithm concentration-pH (log[Me2+]T-pH) diagrams of this system have been made. The effect of ligand and pH value was studied. Two issues in coprecipitation route to synthesize fibrous nickel-cobalt alloy precursor powder, com-position and morphology which are a first priority, are addressed based on thermodynamic analysis and experiments. The results show that suitable pH value range of coprecipitation of nickel ions and cobalt ions in theory can be obtained to maintain fibrous, excellent compositonal homogeneity and stoichiometry in coprecipitation products. Experimental demonstration is also carried out.

Jan 1, 2005