Search Documents

By Vladyslav M. Sokolov

The cost effective and environmentally friendly recycling technology was developed and tested. It enables utilization of the fine nickel-base superalloy scrap in a form of heavily oxidized scarfing granulates. The process of granulates generation was discussed in details. Their properties were investigated. The results of literature search showed anticipated sufficient improvement of the properties of cast iron by its alloying with the elements from the scarfing granulates. The novel alloying approach is based on the two stage reduction operation. Firstly thegranulates were partially reduced in a solid state by their exposure with powdery carbon at the range of 1550 ? 1700°C. Then the gotten product was efficiently introduced into liquid iron since it has a form of fine natural agglomerates for arranging the optimal conditions for reduction of the granulates. The thermodynamic evaluation demonstrates higher reduction efficiency of carbon and silicon dissolved in iron than of the same elements in a form of the separate phases. The considered process partially provides itself by energy since the reaction of reduction of the chromium oxide by silicon dissolved in liquid iron has exothermal character. The mostly complete extraction of Ni was received. The sufficient reclamation of Cr was gotten at the same time.

Jan 1, 2006

By Tang Chaobo

According to the principles of simultaneous chemical equilibrium and electronic charge neutrality, the system of Mg(II)-NH3-CO32--SO42--H2O at 25°C has been thermodynamically analyzed. And the rule of solubility of MgCO3(s) in the system is discovered, the high dissolution field of MgCO3(s) is discovered too. Furthermore, the solubility of MgCO3(s) is increased with the increase of the concentration of SO42-, but it is decreased first then increased with the increase of the concentration of all the CO32- and the total concentration of ammonia and ammonium, and decreased with the value of pH being higher. Those results will has important significance on prepare magnesium chemical products and other salts carbonate that are strict with the content of magnesium with carburization method.

Jan 1, 2006

By R. Upadhyaya

Aluminium alloy matrix cast composites have been synthesised by incorporating fine graphite powders (0.5 - 20 µm size) and chopped carbon fibres (6.5 pm P). 3-6 mm length) by liquid metallurgy technique. Incorporation of these second phase materials exceeding 6-8 wt% invariably resulted in agglomeration of the dispersoids and sometimes leading to even total rejection. It was found that small additions of mischmetal (1-3 wt%) during dispersion resulted in better incorporation without much agglomeration of the dispersoid as evident from the macro and micro structures of the composites. Further, the additions of mischmetal increased the volume of the effective incorporation of the dispersoid even to the extent 50- 60%. The mischmetal addition results in a significant increase in the power factor of the stirrer motor indicating an apparent increase in the viscosity of the system. The higher viscosity of the melt increase the shear transmission conditions within the melt during stirring thereby breaking the agglomerates of the dispersoids. The increased viscosity of the melt seems to be due to the formation rare earth - aluminium inter metallics precipitation, as observed in the metallographic studies, thereby making the process a "pseudorheocasting? technique. A provisional patent has been filed based on this work.

Jan 1, 1989

By Gustavo E. Lagos

Mining is one of the oldest and most important productive activities in Chile. In the latter half of the 80's &d during the 1990's Chilean mining has experienced explosive growth fundamentally due to legislative changes which have encouraged an influx of foreign capital. Fine copper production has grown from 1,4 million tons in 1987 to 3,4 million tons in 1997. Gold production has increased from 17.03 tons in 1987 to 49.46 tons in 1997. In both cases private investment has driven this growth. The direct impact of mining on the Chilean economy has been considered one of the fundamental pillars of the growth of the country in the last years. The indirect impact that has generated on the other sectors of the Chilean economy and in particular the regional economies, has not been analyzed. This paper outlines a methodology for estimating the impact of mining investment and mining operations in different sectors of the Chilean economy at both regional and national levels. It applies this methodology to the case of Minera Escondida, the largest copper mine in the world, analyzing its economic impacts on the regional and national levels.

Jan 1, 1999

By P. W. Godbehere

Over the past three years the Horne Smelter has successfully introduced concentrate smelting by injection in Peirce-Smith converters, allowing definitive closure of its last operating reverberatory furnace, while commissioning a large acid plant treating off gases from its Noranda reactor. Future strategies include a major revision to present converter practices to permit further significant reductions in sulphur and dust emissions. This paper gives an overview of the status of these and other technical and operating developments which will further contribute to ensuring the Horne's position as an efficient custom smelter of primary and secondary feeds.

Jan 1, 1993

By Kalathur S. Narasimhan

Powder metallurgy is a net shape process competing favorably with machining, stamping, forging and castings. The growth of ferrous powder metallurgy over the past four decades reflect the advancements in materials technology, compaction technology, sintering technologies and other related fields. This presentation gives a brief background on how materials technology evolved.

Jan 1, 2006

By M. Boussuge, M. -D. Dupuits, A. Piant

This paper summarises a part of the work that has been essentially carried out at the Ecole des Mines de Paris in the framework of an Eureka European programme funded by the French Ministry of Industry, in partnership with Metaleurop and Carborundum (subsidiary of Saint Gobain). It deals with the measurement of different properties (density, thermal linear expansion, elastic modulus, strength) of a SiC-based refractory constituting the trays that are used in the refining columns in the New Jersey zinc distillation process, especially in the boiling section. These parameters have been investigated to check the homogeneity of the asreceived trays as well as to estimate the influence of ageing of the material under operating conditions. With this aim, specimens have been sampled in used trays having more than two years of operation. The as-received trays exhibited a good homogeneity, the strength being slightly lower in the direction in which they are compacted. Despite microstructural changes, most of the properties measured at room temperature are not significantly affected by ageing. High temperature tests involved thermal treated under vacuum to remove metallic zinc before testing at high temperature. An increase in temperature, as well as ageing, induces a decrease in the elastic modulus and strength.

Jan 1, 2000

By Jared Ball, Benjamin Hogg

There are over 100 process parameters that can be monitored during a single Peirce-Smith (PS) converter batch operation. To support a consistent operation it is important to select the correct Key Performance Indicators (KPI’s) to monitor. They should be strategically chosen to drive the desired behaviour with enough flexibility to endure process variations. At the Xstrata Copper Smelter in Mount Isa most of the PS converter operators have very little experience and are often lacking in the appropriate education or training to properly understand the process. For this reason 10 simple KPI’s were chosen that could be easily comprehended and monitored by all smelter personnel. KPI compliance has been supported by relevant project work in the converter area. Charge sequence trials have been performed in an effort to reduce splash and optimise activity time. The online measurement of full and empty ladle weights has enabled an immediate indication of skull size, skim/slag carryover, and metal loss.

Jan 1, 2009

By G. Cifuentes

When the applied current is interrupted in a copper electrowinning plant, and then is back in operation, the lead anodes tend to corrode. In order to decrease the corrosion, the damage protective ("back up") anodic currents are applied during the period of interruption. The current work aims to establish the effect of the concentrations of sulphuric acid, copper and cobalt on the anode corrosion, to quantify the effect of various anodic protection levels on the anode corrosion and to propose a method to select the appropriate protective current density value.

Jan 1, 1999

By Yang Tian-zu

The separation of precious metals from base metals containing in gold-antimony alloys by selective chlorination leaching under controlling potential was studied in this work. The effects of the consumption of hydrogen peroxide, the concentration of hydrochloric acid, the concentration of sulfuric acid, leaching temperature, leaching time and the liquid-solid ratio in hydrochloric acid system on the leaching efficiencies of the base metals have been investigated. The optimal leaching conditions of the gold-antimony alloys are as follows: hydrochloric acid concentration 4.0mol?L-1, sulfuric acid concentration 1.2mol?L-1, liquid-solid ratio L:S=7.5:1, the leaching temperature 80 0C, leaching time 2h, and the oxidation potential of the leaching system 400±20mV( vs SCE).The leaching efficiencies of copper, nickel and antimony are more than 99% and the gold leaching efficiency is about 0.042% under the above leaching conditions. The base metals containing in the gold-antimony alloy are separated from the precious metals thoroughly.

Jan 1, 2006

By Jung-Ah Kim

Precipitated Calcium Carbonate (PCC) is obtained through calcination, hydration, and carbonation. Thus, the change in each process condition determines the particle size or morphology of PCC. To date, studies on precipitated calcium carbonate have mainly focused on process manufacturing PCC, aimed matter. Still, few studies on calcination or hydration have been conducted. Therefore, this study sought to investigate the effect of hydration condition on the synthesis characteristics of aragonite PCC. Results showed that the particle size of calcium hydroxide changed based on the variation of the initial hydration temperature. In particular, higher initial temperature resulted in the larger particle size of calcium hydroxide used in synthesis. The particle size and yield of aragonite also increased when calcium hydroxide made at high temperature was used. The water/solid ratio or total amount at the hydration time had no effect on the manufacturing process of aragonite, however.

Jan 1, 2006

The presence of clay adversely affects the floatability of copper and molybdenum during processing porphyry copper/molybdenum ores. In addition, reagent consumptions are much higher than when treating clay-free ores. Ores containing kaoline, brammollite, illite and montmorillonite were examined in the laboratory to determine how clay minerals affect the floatability of copper and molybdenum, and to find a possible solution to alleviate the harmful effect of clay slimes. It was demonstrated that the presence of clay mostly affects floatability of coarse and middling particles, and reduces selectivity. The results of the research work showed that there may be several possible ways of reducing the detrimental affects of clay slimes on flotation, some of which include a) use of alternative flowsheets, b) flotation at reduced pulp density, and c) the use of special frothers. The applicability of the findings in plant practice are discussed.

Jan 1, 1999

By Hong Yong Sohn

On the occasion of this symposium in my name, I reflect upon the contributions of my academic mentors and early associates who helped shape my professional career. I was fortunate to have these people around me during my graduate work and at the start of my professional career. In forming my view of the technical field and career, they represented academia, research institutions, industry, and different parts of the world.

Jan 1, 2006

By John Frederick Colloghon, O&apos

Bulong remains the only hydrometallurgical process plant in the world that recovers nickel and cobalt directly from high pressure acid leach (HPAL) laterite leach liquors without need for precipitation of an intermediate product (e.g. sulphide, hydroxide or carbonate). Direct solvent extraction (DSX) of both nickel and cobalt in combination with electrowinning of nickel has been operation at Bulong since early 1999. Focus in the first years has been on ramp-up and resolution of commissioning problems. More recently the focus has been on de-bottlenecking and process optimisation. A number of significant process problems have been resolved, the most difficult being the formation of gypsum in the nickel solvent extraction circuit. Sound control of process chemistry is essential to ensure the production of high quality nickel and cobalt products at the lowest possible cost. This paper describes the numerous changes and enhancements to the process chemistry and plant equipment at Bulong and discusses the importance of ore leach chemistry on downstream impurity metal removal. Potential additional enhancements to further reduce unit costs are also presented.

Jan 1, 2004

By W. Petruk

The silver-rich cobalt-nickel arsenides ores of the Cobalt area in Ontario, Canada were mined for silver from about 1904 to 1985. The ores contained about 8 oz to 100 oz Aglt and about 1 wt% Ni and 2 wt% Co. They were processed by gravitational techniques, screening and flotation to produce separate silver and Fe-Co-Ni arsenide concentrates. The silver concentrate was smelted, and in some cases the arsenide concentrate was sold to custom smelters which recovered silver and other metals. The ores display a wide variety of textures and contain many minor and trace elements. This paper presents an evaluation of mineral characteristics that have a bearing on extractive metallurgy and smelting of this type of ore.

Jan 1, 1993

By S. J. Kohut

Until recently SX-EW technology has only been used to produce conventional cathode for the cyclical commodity marketplace. Unlike electrorefining, SX-EW lends itself to the integration with the downstream manufacturing technologies for direct mine site production of value added products. The integration of SX-EW and downstream manufacturing results in the elimination of redundant process steps, the cost savings, and the access to value added product markets which can buffer the producer from swings in the cathode market. SX-EW production of copper powder and powder-based products has been demonstrated at the pilot plant level. The SX-EW process has been successfully redesigned to meet the more specific demands of engineered products. Challenges include the solution purity, the cell ventilation, the high current density operation and the product handling. Successful demonstration of mine site production of value added SX- EW products opens up new non-commodity marketplaces to the mining industry.

Jan 1, 1999

By Qin Li

An highly active absorbent with oxidization based on fly ash, lime and additives was prepared. Experiments of simultaneous desulphurization and denitrification were carried out using fixture bed and duct injection. The influential factors for the absorptive capacity of the absorbent were studied. The absorptive capacities of 120.7mg for SO2 and 43.7 mg for NOx were achieved at a Ca/(S + N) molar ratio 1.2, respectively, corresponding removal efficiencies of 87% and 76%, while spent absorbent appeared in the form of dry powder. The optimal temperature and humidity of flue gas treated with this process were shown to be approximately 50\\176 and 5% respectively. The mechanism of removal for SO2 and NOx was investigated. In comparison with traditional dry FGD, this process appears to have lower cost, less complicated configuration and simpler disposal of used absorbent. The valuable references can be provided for industrial application by this process. The foreground of application will be vast in China and in the world.

Jan 1, 2006

By M. A. Llavona

The study of the formation and components of copper patina and its conservation has assumed great importance. The changing environment has accelerated the processes of patinas degradation; thus, the exhaustive study of factors capable of affecting the patina formation, growth and durability has assumed great importance for the industrial activity of copper. The main components of the patina, oxides, chlorides, nitrates and sulfates, have been determined; the effect of physical, chemical and microbiological factors on patina formation, particularly the influence of acid rain, natural organic matter, particles and microorganisms have been defined. The effect of different electrolytic solutions that accelerate the formation of copper patinas has been determined, and a review of the state of knowledge of the formation and evolution of metal patinas has been made.

Jan 1, 1999

By Larry Southwick

This paper covers technical and other developments during the first 20 years of Peirce-Smith converting. There were numerous mechanical and process ideas and concepts already being developed and used by others that had possible application within the converter that Peirce and Smith were moving ahead with. There were also other converter configurations in which the basic lining and larger size concepts could function. Finally, as awards and honors began to accumulate, there were those who felt that contributions of other early workers were being ignored. The working out of these conflicts and differing directions will be described.

Jan 1, 2009

By Amanda C. Lima, Luiz Augusto H. Terrones, Sergio N. Monteiro

"Fabric from weaved yarns made of jute fibers have been considered as reinforcement for polymeric composites. In particular, these fabrics obtained from discarded sackcloth are presently being investigated as environmentally friendly composites with recycled polyethylene matrix. The objective of the present work was to compare the practical properties and economical aspects of these composites with those of conventional materials such as wooden board and gypsum panels for building application. The comparison showed that, depending on the amount of post-used jute fabric, a cost/benefit analysis favors these composites over the conventional materials.IntroductionThe increasing amount of wastes generated by human activities is becoming a worldwide problem of pollution with growing consequences to the environment. The question on how to dispose these wastes is, therefore, a major global issue. Among the possibilities of it gating the problem, the use of materials with characteristics of being renewable, biodegradable and recyclable is considered an environmentally correct solution. Examples of this type of materials are left over lignocellulosic fiber from coconut husks and sugarcane bagasse [1] that, after the primary extraction of edible pulp and juices, can be recover for industrial application. Nowadays, the main use of these fibers is to reinforce polymeric composites applied as components for building construction and automobile parts [2,3]. In addition to these applications, composites reinforced with residual lignocellulosic fibers may replace conventional furniture and panels made of wood and thus help to reduce deforestation [4].Environmental protection is not the only motivation for recycling natural fiber wastes. In developing regions activities associate with collecting and processing residual fibers provide job opportunities for low-income people. Moreover, if the lignocellulosic fiber is collected as a recyclable waste, it hes the economic advantage of a comparatively cost, which constitutes in a relevant difference as a choice for commercial utilization."

Jan 1, 2008