Search Documents

By Roderick 1. L. Guthrie, Mei Li

"A mathematical model was developed to study the role of orifice shape in the detection of inclusions in LiMCA (Liquid Metal .cleanliness Analyzer) system. The fluid flow field within the ESZ was obtained by solving the Navier-Stokes equations. The trajectories of entrained particles were calculated using the equations for motion of particles. A numerical study of the effect of orifice shape on signal shape generated by inclusions passing through orifice showed that the signals in a parabolic orifice are gaussian in shape, while those in a cylindrical orifice are trapezoidal in shape. This signal shape difference needs to be taken into account when performing particle discrimination. Orifice shape influences also pass-through fraction of inclusions. Finally, a study of the orifice shape on critical conditioning currents suggested that as the polynominal coefficient of the parabolic orifice increases, the critical conditioning current, which is also the maximum operating current, decreases dramatically. These critical conditioning currents also increase as the fluid flow velocity within the ESZ increases. IntroductionThe presence of non-metallic inclusions in metals often leads to impaired mechanical properties such as a reduction in fatigue strength, and to processing problems such as tear-offs in deep drawing and increased breakage rates in wire drawing operations. Similarly, inclusions cause a variety of surface defects in rolled or extruded products.Prior to the development of the LiMCA system (1) at McGill University in the early 1980's, it was not possible to measure inclusions, in situ, in liquid metals. Compared with other techniques, such as sedimentation, filtration and metallography, which require considerable amounts of labor and time, the LiMCA method has the advantage of providing not only information on the volume concentration of inclusions, but also on the size distribution of inclusions immediately and quantitatively."

Jan 1, 2001

By Gerardo Muñoz

All along this century CODELCO's smelters have been operating on conventional technology, which Codelco has streamlined by using oxygen, developing oxy-fuel burners for reverberatory furnaces and introducing oxygen smelting of concentrates in converters (Teniente Converters). Chuquicamata began capturing sulfur from its first Teniente Converter in 1985. Since then, it has implemented a program allowing to gradually increase such capture. In 1994 a Frame Law on the Environment was enacted in Chile. By virtue thereof and of CODELCO's corporate environmental policy, an investment program aimed at capturing more than 95% of gaseous pollutants in all its smelters in a term not exceeding twelve years was established. The above entails a substantial improvement of the operational management as regards fugitive gases capture and treatment. This paper describes the way CODELCO is to deal with this challenge with a view to fully complying with environmental regulations and obtaining the required environmental certifications of its operations.

Jan 1, 1996

By Valery Kaplan

Sulfur emission in the form of SO2 in flue gases is one of the most serious atmospheric pollutants associated with coal combustion and non-ferrous metals production. The carbonate eutectic method for removing SO2 from flue gases at 723–923 K was initially proposed in the 1970s but despite its great efficiency (SO2 concentration in the flue gas after purification reached 0.003 volume %), it could not be implemented by industry due to the complexity of the carbonate melt regeneration stage. Earlier we proposed a method suited to coal-firing power stations where the melt was regenerated using CO as a reducing agent. However, most metallurgical plants do not use coal and therefore lack a large source of CO. Here we propose a method for removing sulfur from the carbonate eutectic melt by purging it with natural gas or a natural gas/air mixture, which are available in the vast majority of metallurgical plants. This reaction leads to the reduction of sulfate to H2S gas that leaves the melt. The experiments we conducted show that nearly complete sulfur removal from the melt is possible at 823 K and that the reaction rate is sufficiently high for a large scale process. One can foresee that this carbonate melt-based SO2 removal technique may become a practical and economically attractive method for limiting sulfur emission to the atmosphere from non-ferrous metallurgical processing plants.

By F. Michael Hosking

Modeling of a furnace brazing process is described. The computational tools predict the thermal response of loaded hardware in a hydrogen brazing furnace to programmed furnace profiles. Experiments were conducted to validate the model and resolve computational uncertainties. The results from selected furnace simulations and measured thermal events were compared. Critical boundary conditions that affect materials and processing response to the furnace environment were determined. "Global" and local issues (i.e., at the furnace/hardware and joint levels, respectively) are discussed. The ability to accurately simulate and control furnace conditions is examined.

Jan 1, 1998

By Varadarajan Seshadri

The performance of mould fluxes in satisfying its quality requirements can have a significant effect on the efficiency of the continuous casting process and on the surface quality of the products. This performance is affected by various parameters including the characteristics of the mould fluxes, the quality of the steel being cast and the operational conditions of the caster. The extremely complex relationships involving the parameters mentioned above make it very difficult to have simple criteria for selecting mould fluxes for casting a certain grade of steel in a continuous casting machine. These difficulties led steelmakers and mould flux suppliers to select mould fluxes based mainly on plant trials. In the present work, a software to help in the analysis and development of mould fluxes for continuous casting was developed_ This software includes several models for prediction of mould flux viscosity and consumption. A mathematical model was also used to predict the heat flux through the mould flux. The proposed methodology was applied to continuous casting of crack sensitive steels_ Some of the results given by this software are presented, discussed and compared to plant data.

Jan 1, 2003

By Toru H. Okabe

As part of a systematic study on the thermodynamic properties of complex nitrides, phase equilibria of the system Li-M-N (M Mg, AI, Ga) at 900 K were investigated. An attempt to determine the thermodynamic properties of complex nitrides was made by using the galvanic cell method, which utilizes LiMgN as an electrolyte under nitrogen atmosphere. The electromotive force (Emf) of ilie cell at temperatures between 800 and 1100 K was measured. Whilc the Emf of the cell at 900 K was measured to be 0.137 V, data discrepancies of ±0.03V were found. It was difficult to determine temperature dependence of ilie Emf. The Gibbs energy change for the reaction, 113 LbN (s) + 1/3 Mg3N2 (s) = LiMgN (s), at 900 K was determined to be tJ.Gor (LiMgN) -13.2 (±2.9) kJ/mol. Using thermodynamic information on ilie binary nitride from literature, the standard Gibbs energy of LiMgN was derived to be AGO f (LiMgN)= - 121 kJ at 900 K. The thermodynamic stability range of nitride was discussed by constructing isothermal chemical potential diagrams that provide a better understanding of ilie stability region of the LiMgN phase. The diagram was found to be in good agreement with the isoiliermal phase diagram determined by ilie alloy equilibration meiliod. Although the obtained data includes large uncertainties, the results provide a better understanding of the iliermodynamic stability of nitrides. The potential application of this complex nitride to nitrogen chemical sensors or a medium for controlling nitrogen potential is also shown.

Jan 1, 2003

By Katsuyoshi Kondoh

The utilization of silica particles originated in rice husks as reinforcements of magnesium composites was discussed. By using the solid state reaction of rice husk silica particles with magnesium powder, P/M magnesium based composites dispersed with the magnesium silicide (Mg2Si) and magnesium oxide (MgO) were fabricated. High-purity silica particles were originated from rice husks, one of the major agricultural wastes, via the citric acid leaching treatment and combustion in air. The effects of the silica particle characteristics such as size, crystalline and porous structures, on the reactivity of silica and magnesium to synthesize Mg2Si intermetallic were discussed. Amorphous silica was more useful for this reaction than crystalline one. The reactivity of rice husk silica was superior to that of the conventional mineral silica particles because of not only its amorphous structure but the larger specific surface area due to their pore structures. In the case of the green compact of the mixture of the rice husk silica and Mg powder, the silica particle size was not effective on the reactivity because the coarse particles were fractured into fine ones by cold compaction. The distribution of Mg2Si intermetallics of magnesium powder composites consolidated by SPS process was investigated by XRD and SEM-EDS analysis. Their mechanical and physical properties were also evaluated in detail.

Jan 1, 2009

By Pedro A. Netto, Giulio R. Altoé, Sergio N. Monteiro, Ygor M. Moraes, Frederico M. Margem, Gabriel O. Glória

Since environmental issues are becoming more and more important Worldwide. Nowadays, Natural fibers are been used to substitute the synthetic ones. Although PALF fiber is an important natural fiber and its mechanical Properties surpass in various aspects some other lignocelluloses fibers, such few studies have been conducted with the fiber obtained from leaf of PALF plant. In order to better evaluate the mechanical properties and possible applications, this paper aims to improve the elastic modulus of the PALF fiber by Weibull statistics, by evaluating their mechanicals properties and possible applications. The fibers were divided in diameter intervals and the tensile strength and elasticity modulus were measured in each range. The fractured surface was examined using scanning electron microscopy. The results, interpreted by the Weibull statistical method, showed a correlation between the fiber elastic modulus and its diameter.

Jan 1, 2015

By Jasper Kwong

The recycling of MgO-C refractories as a slag conditioner in EAF (electrical arc furnace) foaming slags have been evaluated by the Albany Research Center. The amount of MgO in the slags is critical for the foaming quality. Good foaming slags provide the benefits of high energy efficiency and low refractory consumption and require saturation with MgO. A computer model predicting the chemistry of MgO saturated foaming slags was designed to predict suitable amounts of MgO additives from MgO-C spent refractories. This model can also help to reduce the amount of slags and to improve the economics of producing steel. The implementation of this recycling program is underway at steel plants and the experience of recycling spent refractories will be discussed.

Jan 1, 2002

By Guangchun Yao, Chuan Li, Hongjie Luo, Zhuokun Cao

"The expansion rate and collapse time of liquid aluminum foams are essential for the determination of operating time and quality of the resulting foam. In the present paper, liquid aluminum foams was fabricated by adding in TiH2 as blowing agent, and the variation of expansion rate with foaming time was non-contact detected by a laser distance measurer. The influence of different stabilizing agent and alloying elements was studied. The results show the fact that the fraction of stabilizing agent only perform little effects on the maximum expansion rate of liquid aluminum foams, while the influence of alloy elements are remarkable. The maximum expansion rate would increase much when Mg is added, and the liquid foam also collapse at a shorter time. Comparison was made between experimental results and mathematic calculations, which reveal the fact that it is the change of TiH2 decomposition responsible for the change.IntroductionMetal foams, combining light weight with other unique mechanical and physical properties, have gained wide interest and been developing fast during past few decades. However, manufacture of this new material is quite challenging since it involves simultaneous occurrence of gas, liquid and solid phase at high temperature [1-2].Quite some manufacture routes have been developed for manufacturing metal foams, and the structure and quality of resulting foam are remarkably improved during the last decades. However, most of the past works seems to be experiential, and because the lack of basic knowledge of foaming process, the start material is limited and the production technologies are far from reliable and reproducible.[3-4]In direct foaming process, decomposition of blowing agents, TiH2 for example, is the main force for foam expansion. The density and foam structure changes with time during the foaming process, so it is expected that foams of certain structure can be obtained by solidification of the liquid foam at a certain time [5-6]. However, the foaming process is weak in reproducibility and the influence of stabilization additives and alloying elements is unclear."

Jan 1, 2011

By Mark Osborne, Ray D. Peterson, C. Edward Eckert

"The theoretical melting energy requirement for a typical hypoeutectic aluminum-silicon alloy is approximately 520 BTU/lb. It has been demonstrated, however, that even a state of the art secondary processing-automated lost foam casting operation can exceed this value by at least an order of magnitude when the actual thermal energy input from melting to solidification is monitored. Metal transfer and holding operations constitutes over 65% of this expenditure. The authors present relative benchmark energy expenditure information by unit operation for an offsite melting/lost foam casting line with a daily throughput in excess of 100,000 lbs. Efficiency improvements through optimization of the current process, and anticipated energy values at the culmination of a U.S. Department of Energy sponsored project to develop, integrate and demonstrate an advanced melting, transportation, and dispensation system will be cited.IntroductionThe size of the U.S. aluminum remelt pool was approximated to be 14.21 billion kg (31.27 billion pounds) by a recent study?, with the engineered castings (foundry) sector accounting for 3.25 billion kg (7.16 billion pounds) or 23% of that total. This study considered overall process yield and all major contributors to scrap. The values cited, therefore, are more meaningful than simply tabulating annual pounds shipped by sector.The foundry sector consists of Sand Castings, PM Castings and Die Castings categories appearing in Figure 1. All other categories comprise the wrought alloy sector. Wrought alloy production enjoys an energetic benefit from both scale and a relatively continuous operation. Many foundry operations, however, operate in batch mode at less than design metal throughput with characteristically longer melt holding periods. Since any detention of molten metal beyond melting represents an overhead use of energy, melt holding (secondary) energy expenditures can appreciably inflate melting energy requirements in the foundry."

Jan 1, 2009

By Neale R. Neelameggham

"Most chemical process plants and metallurgical production facilities have some sort of cogeneration to minimize process energy costs. Use of Alternative Energy Production from sun and wind power with storage can become an integral part of a process plant utility. This will facilitate reduced fossil fuel usage and help minimize thermal emissions. This will be similar to Pollution Control equipment, which have become an essential part of process plants in the past four decades. Conceptual flow sheets of such Process Utility schemes are presented.IntroductionPower is supplied to industries, commercial and residential users. Over the past decade, Electric Utility companies have made major inroads, in introducing alternative energy resources in an attempt to somewhat reduce fossil fuel use in power generation. Now, on a much larger scale than in the early 1980s, residential users, motivated by government provided tax credits, have started installing alternative energy generators such as roof top wind mills or roof-top photovoltaic generators. This will minimize future energy costs, help control thermal emissions etc. This alternative power generation is typically connected to the existing power grid with two way power metering. However, the use of alternative energy generation has not been seen at large industrial sites yet.Paul Scherer Institute, Switzerland and the NREL laboratories in Colorado, are two of the several institutes which have been developing how solar thermal power can be used to supply the endothermic input energy in chemical and metallurgical processes. The theme of this present symposium addresses the above as well as the energy storage needs for such events to become continuous. This paper emphasizes the concept of how alternate energy can be used in the production of materials on a generic sense wherever there is a need for input energy – beyond endothermic process energy - while addressing how to reduce the thermal and carbon emissions.The alternative energy generation using wind or solar source is discontinuous due to the nature of the energy source. They are not only discontinuous but also variable. This necessitates storage of generated power for close to continuous use with variable loads. C Smith, et al pointed out in 2006, that 'the electric power industry has taken notice of the expansion of wind and its potential' in a summary article on integrating wind generation into utility systems.1 In 2009, the 1000 MW wind generation project in Texas had to be postponed to 2013 for lack of transmission.2 There are only a few large MW solar generation units in the US; the projects being slow mainly from lack of adequate storage and redistribution."

Jan 1, 2010

By C. Segawa

SMM operates an original slime treatment process for recovering precious metals and other metals (Te,Se,Sb,Bi)from the copper and the lead anode tankhouse slimes. In recent years, the amount of slimes has increased and the pyrometallurgical processing units capacity became the bottleneck of the entire plants. For the expansion of the plant, new pyrometallurgical facilities, incorporating a BBOC, was commissioned in 1992 and has now been successfully operated. In addition, unit operations were optimized to increase recovery and reduce operating cost .. The results of modifications made in the plant are discussed in this paper.

Jan 1, 1996

By Peng Lv, Shiqian Liu, Bin Xu, Qian Li, Yongbin Yang, Tao Jiang

The treatment process of a low-grade refractory gold ore containing sulfide minerals and carbonaceous matters was studied in this work. The gold extraction of this ore by all-sliming cyanidation was only 11.75%. Hence, a pretreatment was necessary. In this paper, a flotation-preoxidation-cyanide leaching process was developed. The concentrate from the flotation procedure was processed using different preoxidation methods. A concentrate containing 34.08g/t of gold with the gold recovery ratio of 81.20% was obtained by flotation. After roasting, microwave heating or alkaline pressure oxidation, the gold cyanidation ratio reached 82.37%, 81.26% and 71.09% respectively. Roasting was an effective, reliable and mature technique to oxidize sulfide minerals and carbonaceous matters. Roasting and microwave heating both produced dangerous environmental pollutants while alkaline pressure oxidation was eco-friendly.

Jan 1, 2015

By J. G. Zafiratos

The leaching of a Greek low-grade manganese dioxide ore, not amenable to conventional mineral processing operations, was studied using a mixed culture of Thiobacillus sp. bacteria. The experiments were carried out in specially designed continuously aerated and stirred tank reactors arranged in two-tank series. The first tank of each series was loaded with an elemental sulfur culture suspension while the second was loaded with a manganese ore high density slurry. The bacterial culture had been previously adapted to grow on elemental sulfur and also in the presence of manganese ore and dissolved manganous ion. A two level full factorial design was constructed in order to study the effects of the ferric ion concentration in the leach solution, the "elemental sulfu weight to ore weight" ratio, the ore pulp density and the composition of the dispersed gas. The responses which were investigated included percentage manganese recovery, co-dissolution of iron and manganese dissolution rate. Parameters with constant values throughout the experiments were the leach solution pH, the nutrient medium composition, the dilution rate and the ore and sulfur grain sizes. It was found that the ferric ion concentration was the most significant factor and had a positive effect on the final percentage extraction of manganese from the ore and also on the rate of manganese solubilization from the ore. The effects of the other factors studied are discussed in detail.

Jan 1, 1997

By Basant L. Tiwari

An electrolytic process, based on a three-layer concentration cell, to extract magnesium from commercial aluminum alloy scrap has been examined. The process was repeatedly tested at 1025 K with two cells of d1fferent sizes, 0.6 kg and 5 kg feed aluminum, to have a better understanding of the opera ting parameters and evaluate the scale-up potential. In both cells, the magnesium content of the scrap was selectively reduced ?from 1. 1 to less than 0.1 wt.% at anodic current dens-Hy as high as 1. 1 A/cm2 with current efficiency exceeding 85%. Magnesium was recovered in the form of salt coated globules. Comparison of performances for the two cells suggests that the process can be scaled up. With further development, this process could become a viable alternative for demagging secondary aluminum.

Jan 1, 1985

By Jewel A. Gomes

Keywords: Electrocoagulation, arsenic removal, fuel cell, windmill, energy simulation, combined Fe-Al electrode assembly Arsenic contamination of well-water in different countries has caused signs and symptoms of arsenic poisoning. Although several physicochemical treatments are presently used for the removal of arsenic compounds from drinking water, an electrochemical treatment, electrocoagulation, is a promising processing technology and currently is the most efficient (above 99% removal) and environmentally friendly technique, particularly if combined with alternative energy sources. Wind and fuel cell technologies can be considered the most promising developmental clean power sources. We will discuss new insights into the materials processing mechanisms and show the coupling of electrocoagulation with fuel cells and simulated wind energy sources. Different electrocoagulation plate materials were considered, along varied currents from the fuel cell to produce maximum arsenic removal. Coupling these technologies will remove carcinogenic arsenic from water sources, and will exhibit efficient usage of these energy sources by producing pure water for human and agricultural consumption.

Jan 1, 2005

By Sebastiaan Peelman

NdFeB permanent magnets are the best available magnets used in many technology applications. However, at their end-of-life (EoL) most of magnets and the contained REEs are lost during the recycling of the bulk metals. The REEs are classified as the most critical raw materials in the European Union, and recycling of REEs from EoL products will reduce their criticality and contribute to the sustainability of REE. Various technological routes have been reported, but most of the methods are effective for highly concentrated magnets or magnet scrap, which is greatly dependent on expensive pre-dismantling processes. This paper presents various innovative metallurgical solutions to the effective REE recovery from current industrial practice for WEEE recycling, including the ferrous scrap from WEEE shredder products and shredder residues from computer hard disk drives. Both hydrometallurgical and combined hydro- and pyrometallurgical REE recovery routes are developed after demagnetization and physical upgrading.

By J. J. Rush

Neutron scattering and analysis techniques are extremely powerful, often unique, probes for the characterization of the amount, location, bonding states, and dynamics of hydrogen in all classes of materials. Developments over the past decade at the NIST Center for Neutron Research and elsewhere have greatly increased the sensitivity and dynamic range of neutron methods. In this paper, we provide a flavor of the capabilities of modem neutron instrumentation for the study of hydrogen in a number of technologically interesting systems, including metal hydrides, fuel-cell materials, fullerenes, and disordered carbons.

Jan 1, 2002

By Gordon A. Irons

"Powder injection for melt refining is widely practiced in the steel industry, and is gaining acceptance in the non-ferrous industries. In these commercially-important systems, the thermodynamics and kinetics may be very complicated. More than one element may be removed by refining, and often the refining agents are not just one compound. In this paper, the thermodynamic and kinetic aspects of these processes are reviewed. A number of examples are given, such as the desulphurization of iron with a variety of reagent mixtures, and selenium removal from copper with several different reagent combinations.IntroductionI am very pleased and honored to present a paper at this Symposium recognizing the many contributions of Professor Howard Womer. Even at the time I was an undergraduate student, the WORCRA process was part of the curriculum. I remember at the time that I was fascinated by the concept, and due to it and the many other rapid developments in Process Metallurgy, I chose it as my field of study. I think the Symposium is testimony that Professor Womer has touched the lives of many others as well.My original assignment was an overview of the basic aspects of gas and solids injection. However, I reviewed most of this material at the Savard/Lee Symposium [1]. In the present paper, I will present some of the basic issues related to refining with powder injection, using work that we have recently completed in both ferrous and non-ferrous systems."

Jan 1, 1996