Search Documents

By Antti Roine

Sulfidic zinc concentrates are usually roasted in a fluidized bed furnace into sulfur-free oxide form. Metallic zinc is produced from this oxidic calcine using hydrometallurgical leaching, solution purification and electrowinning stages. The roasting step is necessary because zinc oxides are easier to dissolve using traditional leaching methods than zinc sulfides. The Kokkola Zinc smelter uses various types of zinc concentrates and secondary materials as feed mixture. This makes it difficult to find optimum process parameters for the roaster when the composition and particle size distribution of the feed mixture varies even on a daily basis. Certain conditions may even cause difficult accretion problems or increase the amount of calcine in the process off-gas line excessively. A thermochemical heat and material balance model was developed for process advisor, in order to estimate the effects of different process parameters (temperature, process air coefficient, concentrate feed, oxygen enrichment, water feed, etc.) on the heat balance, roasting temperature and calcine composition. This model was constructed using the heat balance module of HSC Chemistry 4.0 software. The prevailing chemical compounds in the concentrate and calcine were verified using mineralogical analyses and equilibrium calculations. The roasting process seems to operate near chemical equilibrium conditions, if the behavior of the main components is considered. This paper describes briefly the basic principles of the calculation model and outlines the results with several diagrams and discussion. The calculated results were in reasonable agreement with the recent process air oxygen enrichment and water feed test campaigns carried out at Kokkola in 1999.

Jan 1, 2000

By Gunther Klamp

Disposal of arsenic compounds from washing acid in metallurgical plants is becoming a severe problem when using lime neutralization. A further problem is the disposal of relatively large quantities of gypsum which is produced during this neutralization step and which Is also conta-minated with other toxic metal compounds. The Sachtleben-Lurgi process removes arsenic and other metals from washing acid in the form of insoluble sulphides. The purified acid contains less than 0.5 ppm of arsenic and can be used for standard sulphuric acid applications. The process Is demonstrated commercially at Sachtleben's acid plant since more than five years.

Jan 1, 1992

By Chenhui Liu, Ka-ma Huang, Hong-ying Xia, Bingguo Liu, Hua Chen, Jinhui Peng, Libo Zhang

"The rising popularity of microwave heating in mineral processing has fuelled the need for knowledge concerning dielectric properties of minerals. Dielectric property and microwave absorption property of anthracite were measured over a temperature range of 20-100°C at 2.45GHz by using an open-ended coaxial sensor measurement system. The results show that the dielectric constant, loss factor and loss tangent increase with temperature rising at 2.45GHz. Microwave absorption properties of anthracite are highly dependent on temperature and frequency. At frequency of 2.45GHz frequency used in microwave metallurgy, anthracite is suitable for reducing agent to achieve fast elevation of temperature then returning to original state. The research will be helpful in explaining the thermal running of microwave dielectric heating the anthracite.IntroductionThe application of microwave heating in minerals processing and treatment has recently attracted great interest from the metallurgical industry. Compared with conventional heating methods, the advantages of microwave heating include rapid and selective heating, uniform distribution, high efficiency, fast on and off switching as well as flexible and modular design[l-3]. As a result of these advantages, microwave heating has been applied in a variety of mineral processing and extractive metallurgy, such as microwave-assisted ore grinding, microwave heating for carbothermic reduction and acid leaching of ilmenite ore, microwave drying, microwave-assisted roasting and smelting of sulfide concentrate, microwave-assisted spent carbon regeneration and microwave-assisted waste management [ 4-6]. Though the application of microwave heating in the metallurgical industry is promising, further studies on the interaction between microwave radiation and minerals and its effects are highly desired to develop innovative techniques for minerals processing and ore treatment using microwave heating [7]."

Jan 1, 2013

By C. Hennesmann, D. Maijer, S. L. Cockcroft, P. Yo

"Die cast aluminum wheels are one of the most difficult automotive castings to produce because of stringent cast surface and internal quality requirements. As part of a collaborative research agreement between researchers at the University of British Columbia and Canadian Auto Parts Toyota Incorporated, work has been underway to predict heat transport and porosity formation in die cast A356 wheels. The basic heat transfer equations have been solved using the commercial finite element package ABAQUS to which specialized routines have been added to predict porosity. Preliminary work on predicting porosity formation focused on using the Niyama parameter as a measure of the probability of porosity. The latest version of the model incorporates a new fundamentally based porosity criterion, which takes into account the effect of hydrogen concentration. The development of this model together with its application to a series of cylindrical test castings as well as a production cast wheel are presented.I. IntroductionDie cast aluminum wheels are one of the most difficult automotive castings to produce because of stringent cast surface and internal quality requirements. Microporosity, in particular, is a common defect that can adversely affect wheel quality. The mechanism of microporosity formation in aluminum alloys is complex owing to its dependence on the interaction of a number of phenomena occurring during solidification including the decrease in hydrogen solubility, the decrease in volume, the development of the solidification structure, and the increase in difficulty in interdendritic feeding [1]. As a result, the amount, size, and distribution of microporosity is affected by a large number of casting parameters including thermal variables, melt composition, grain structure, modification, and inclusion content, making optimization by trial-and-error methodologies difficult.The use of criteria functions, based on thermal conditions during casting, offers a relatively simple approach to predicting microporosity. In practical terms, they are useful because they provide a straightforward method of assessing the impact of varying casting parameters on porosity through various thermal parametersl21 such as thermal gradient, cooling rate, solidification time, and solidus velocity. Drawbacks of criteria functions include insensitivity to varying hydrogen concentration and the limitation to qualitative predictions. Consequently, in aluminum alloys, attempts have been made to develop models incorporating the effects of hydrogen gas and microstructure evolution. However, these types of models represent a significant increase in complexity and sacrifice the simplicity and ease of application of the thermally based criteria functions."

Jan 1, 2001

By S. Ferlay

"The main purpose of the ZIMA VAL project (Label EUREKA EU1367 and LIFE ENV/F/000278) is to demonstrate industrial scale recovery and recycling of the main components of used dry batteries (zinc, manganese dioxide, mercury, and stainless steel) into high added value products. The originality of the ZIMA VAL process resides in:1- the use of hydrometallurgy2- alkaline treatment implementation (highly selective) for zinc and mercury3- electrochemical recovery of high quality products.4- the recycling of all the battery components (zinc, mercury, manganese dioxide, stainless steel) ·5- low operating and investment costs.The process consists of physical classification, mechanical dismantling, hydrometallurgy and electrochemistry. The purpose of the demonstration plant in FALAISE (Calvados - France) is to define the technical and technological parameters of an industrial unit for the treatment of 2400 tonnes per year of used batteries."

Jan 1, 2000

By Wilhelm Wendt

About five years ago we showed that it is possible to use the spectral in- formation in the light emitted by the off-gas flame of a PS converter for on-line production control. Very recently measurements have been performed using improved optical equipment and data evaluation software, resulting in both improved accuracy and the establishment of new optical process parameters. Using the optical signals the slag heats could be stopped at a predetermined Cu content of the white metal with an accuracy of +0.2% Cu m the range 74-78% Cu. A good correlation was found between the slag composition and optical data, providing a possibility for on-line monitoring of the SiO2 content of the slag. The measurements indicate the possibility of predicting the optimum end-point of the copper-making stage and having real time information on the impurity removal. Factors influencing the optical parameters, such as blowrate, Pb content, temperature etc. will be discussed.

Jan 1, 1993

By C. M. F. Viera

In this work the properties of a clayey ceramic incorporated, up to 10 wt.%, with three types of wastes from a water treatment plant was evaluated. To determine the physical and mechanical properties such as linear shrinkage, water absorption and diametrical compression, specimens were prepared by 18 MPa uniaxial pressure and then fired in laboratory furnace at 700oC. The results indicated that the wastes incorporation changed the properties of the clayey ceramic. From the results it was found it possible to recycle these wastes into clayey ceramic in low amounts to avoid deleterious effect on the quality of the fired product.

Jan 1, 2008

By R. S. Tahautdinov, A. N. Posazhennikov, V. V. Bastrygin

"The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Samples of iron ore and carbon reductant were chemically and physically analyzed. Green pellets were processed via a lab tube furnace to simulate RHF conditions. The nuggets and slag were chemically analyzed. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities in 1996 [1]. After pilot testing at Kobe Steel’s Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics has committed to building the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota). Only 4 iron ore types (hematite, magnetite, high Al2O3/SiO2 and low Al2O3/SiO2), as well as 4 coal types with range of volatility, ash and fixed carbon were tested. Results were consistent with nugget characteristics confirming ITmk3’s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from iron carbonate bearing ore with high content of MgO has been done. Such kind of iron ore is restricted for charging into the blast furnace due to contamination of MgO. The reason for restriction is the limitation of load of MgO in the blast furnace. If a lot of MgO enters the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace."

Jan 1, 2011

By Jinwu Kang

The hydraulic turbine blade of the matensitic stainless steel (Cr13%,Ni5%,Mo1%) is a kind of large and curved shape, which is susceptible to deformation in both casting and heat treatment processes. The coupling analysis of heat transfer, phase transformation and stress in heat treatment process of the turbine blade for Three Gorges Project is carried out by using Deform-3D software. Its temperature fields, phase fields and stress fields in heat treatment process are obtained. And its deformation is predicted. In the cooling process of normalizing, the blade exhibits relatively large deformation. Based on the stress analysis and deformation prediction in heat treatment process, an algorithm for the determination of reverse deformation of the blade casting in heat treatment process is presented. And the reverse deformation distribution of blade is obtained.

Jan 1, 2010

By Cheng Pan, Qiugang Yuan, Xuewei Lv, Mei Liu, Enguang Guo

Land-based nickel resources include nickel sulfide and nickel laterite. With the consumption of high grade nickel sulfide, use of nickel laterite has received more and more attention. The mineralogy and sintering behavior of limonitic nickel laterite with high iron and low nickel and silica was studied to offer technical support for producing ferronickel through sintering–blast furnace route. The mineralogy results showed that the main phases in this kind of nickel laterite are goethite (FeO(OH)), gibbsite (Al(OH)3) and NiFe2O4. The TGA (Thermogravimetric Analysis) and DSC (Differential Scanning Calorimetry) revealed hydroxide minerals in addition to absorbed water. After the sintering experiments the chemical composition, phases present (XRD analysis) and physical properties of the sinter were studied. The content of FeO in the sinter increased with increasing basicity up to 1.3, and then decreased with further increase in basicity. The yield of sinter increased (from 73% to 80%) with increase in the basicity from 1.1 to 1.7, and then the yield decreased with the further increase in basicity. Mg(Ni)(Fe,Al)2O4 is the main phase in the sinter while MgCaSiO4 and Fe2SiO4 is the main binder phase when the basicity is 1.1~1.5, and MgCaSiO4, Fe2SiO4 and SFCA is the main binder phase when the basicity is 1.7~2.1.

Jan 1, 2014

By R. L. Miller

Oil -bearing metal sulfide sludges produced in treatment of an industrial wastewater, which includes plating wastes, have yielded to treatment by electrooxidation and hydrogen peroxide processes. The oxidation can be controlled to be mild enough to avoid decomposition of the organic phase while oxidizing the sulfides to sulfates. The pH is controlled to near neutral conditions where iron, aluminum and chromium(II1) precipitate as hydrous oxides. Other metals, such as lead and barium, may be present as sulfate precipitates with limited solubility, while metals such as nickel and cadmium would be present as complexed ions in a sulfate solution. The oxidations were found to proceed smoothly, without vigorous reaction; heat liberation was minimal.

Jan 1, 1992

By Dimitrios Fillippou

Magnesium hydroxide is used in a number of industrial applications, from the neutralisation of acid effluents to the production of pharmaceuticals. High-quality magnesium hydroxide powders can be produced by hydrating slow-reacting magnesia in dilute magnesium acetate solutions. The process of magnesia hydration shows many similarities with a typical hydrometallurgical leaching operation; however, its kinetics are crucial not only for process design and control, but also for the production of powders with a desirable particle morphology. This article shows the results of an experimental work whereby industrial heavily-burned magnesia powders were hydrated in 0.01 to 0.1 mol/L magnesium acetate solutions at temperatures ranging between 333 and 363 K. Examination of the magnesium hydroxide produced and the analysis of the kinetic data suggest that the hydration of heavily-burned magnesia in magnesium acetate solutions is a dissolution-precipitation process controlled by the dissolution of magnesia particles. The activation energy was estimated to be 60 kJ/mol, while the reaction order with respect to magnesium acetate concentration was found to be about one.

Jan 1, 1999

By P. Balachandran

The paper outlines the existing facilities and working practices at the Khetri electro-refinery of Hindustan Copper Limited. Plans have been drawn up to mechanize some key operations to improve the quality of cathodes and the working environment as well as economize the refinery operations. The economic analysis for determining various optimum operational parameters under conditions existing in India have also been outlined. The impact of capacity utilization and mechanization under different sets of conditions on operational costs have been highlighted.

Jan 1, 1987

By Duclerc Fernandes Parra, Washington Luiz Oliani, Christiano Gianesi Bastos Andrade, Ademar Benevolo Lugão, Danilo Marin Fermino, Francisco R. Valenzuela Diaz

This work concerns the study of the effect of discarded bond paper on the mechanical behavior of polypropylene/organophilic clay nanocomposites. A brown polycationic bentonite from the state of Paraíba, Brazil, was treated with sodium carbonate to transform it into a bentonite that swells in water and then treated with hexadecyltrimethylammonium ammonium chloride to transform it into a bentonite that swells in organic liquids. Polypropylene with 3 % polypropylene graft compatibilizer (PP-g-AM) was mixed with 1 % and 2 % by weight of discarded bond paper and with 1% and 2% by weight of organophilic clay using a twin-screw extruder. The specimens were prepared by the injection process. The clay as received and after organophilization was characterized by XRD, SEM, and capacity of swelling in water and in organic solvents. The nanocomposite specimens were characterized by XRD and thermal analysis. The mechanical behavior of the injected specimens was evaluated by strength, flexural and impact tests. The nanocomposites showed improved mechanical properties compared with the polymer without filler.

Jan 1, 2015

By F. T. Principe

In order for solvent extraction technology to be acceptable as an alternative to existing jarosite precipitation circuits, iron must be cleanly separated and concentrated into a feed stream suitable for downstream iron by-product recovery which meets market specifications and economics. Ten years ago, significant progress was made in a joint McCill University/CANMET project that involved iron extraction with mono(2-ethylhexyl) phosphoric acid and stripping with HCI. Our iron solvent extraction research was reactivated recently by looking into this and other members of the organophosphorus extractant family. Our research focuses on the mechanisms and control of anion (SO42/CI) transport across the various phases (Rafinate/Organic/Strip), iron build-up in the strip liquor, and extractant stability/selectivity. In this paper, these issues along with some other performance parameters are discussed using data derived from an extensive search of the two commercially available and best known members of the organophosphorus family, di-2-ethylhexyl (D2EHPA) and mono-2-ethylhexyl (M2EHPA) phosphoric acid. Further in this discussion, the challenges lying ahead in the development of sx systems that overcome the deficiencies of D2EHPA and M2EHPA are outlined. In particular, the necessity of considering secondary separation technologies that can further concentrate iron values in the chloride strip liquor to levels economically attractive for the production of saleable iron oxide by pyrohydrolysis is addressed.

Jan 1, 1998

Primary sulphidic gold ores in the Archean provinces of Western Australia can be broadly sub-divided into pyritic, pyrite-telluride, arsenical and antimonial types. Pyritic ores contain only native gold, and are essentially not refractory. Arsenical ores almost always carry some invisible gold, and may vary from mildly to highly refractory. Pyrite-telluride ores contain gold-bearing tellurides, and are refractory to varying degrees. Antimonial ores usually contain aurostibite, and may be very difficult to process. A classification scheme for metallurgical processing, based on mineralogy, is proposed for the ores, and implications for processing are discussed.

Jan 1, 1995

By Deming Wang, R. A. Overfelt

"The oscillating cup viscometer has become a dominant technique to measure the viscosities of high temperature molten metals. Unfortunately, the viscosity estimation model from the observed logarithmic decrement and period of the oscillation is very complicated. There are still large discrepancies of viscosity estimation values between using different measurement facilities and using different viscosity estimation models for a same molten metal. The purpose of the paper is to evaluate the accuracy of an oscillating cup viscometer in Auburn University. Two well known viscosity estimation models, Roscoe's and Torklep's equations, are compared and discussed. The theoretical literature for the fluid flow inside an oscillating cup is reviewed and a more accurate working equation for the Auburn oscillating cup viscometer is developed. Some design parameters of the oscillating cup viscometer, which directly affect the accuracy of viscosity estimation by using the working equation, are discussed. In addition, applications and experimental measuring data are presented in the paper for several different commercial alloys, such as aluminum alloys: A319, A356 and A201, nickel-base super alloys: In713 and In718, and casting irons, C40 Gray Iron and Ductile Iron.1 IntroductionThe oscillating cup viscometer is the most important and has been most frequently used in viscosity measurement for high temperature liquids [1-4]. The principal advantages of this technique over others are its mechanical simplicity and the ability to measure the time period and amplitude decay with great precision. In the viscometer, a high temperature liquid (such as a molten metal) is contained within a crucible suspended by a wire to form a torsional pendulum, which induces torsional oscillation motion. This motion is damped primarily by viscous dissipation within the viscous liquid inside the cup. The viscosity of the liquid can be calculated by an analytical or numerical solution ofthe equations of motion of the oscillating cup system."

Jan 1, 2001

By D. Papazoglou

This work was undertaken to investigate the thermodynamic and kinetic feasibility of using hot sulfur dioxide bearing gases from smelting processes to selectively sulfate the nickel in nickel laterite ores for subsequent extraction in water. The environmental benefits of this approach, as opposed to releasing the gas to the atmosphere, and the economic benefit of directly utilizing the SO2 rather than converting it to sulfuric acid are strong drivers for such a process. A thermodynamic analysis indicated that selective sulfation of the nickel could be feasible under appropriate conditions and these were explored through a series of laboratory scale experiments. Laterite samples were reacted at temperatures between 500 and 800°C with an equilibrated mixture of sulfur dioxide, oxygen and nitrogen in a fixed bed reactor. Tests were conducted on saprolitic ore from Bulong, Western Australia:, limonitic ore from New Caledonia and gamieritic ore from Indonesia. Nickel extractions were highest from the limonite and relatively low from the other ores. The maximum selective extraction of nickel from the limonite in a single stage sulfation was 73%. Sulfation of other elements present in the laterites was also examined. A two-stage process was also identified which involved sulfation using a strong sulfation potenrial followed by weaker sulfation potential to attempt to convert ferric sulfate formed in the first stage to ferric oxide. This increased the extraction for the limonite ore to around 84% Ni, 95% Co and 2% Fe. Direct sulfation of laterite could be feasible in locations where sulfide smelting or roasting operations are relatively close to laterite deposits.

Jan 1, 2003

By D. Papazoglou

This work was undertaken to investigate the thermodynamic and kinetic feasibility of using hot sulfur dioxide bearing gases from smelting processes to selectively sulfate the nickel in nickel laterite ores for subsequent extraction in water. The environmental benefits ofthis approach, as opposed to releasing the gas to the atmosphere, and the economic benefit of directly utilizing the S02 rather than converting it to sulfuric acid are strong drivers for such a process. A thermodynamic analysis indicated that selective sulfation of the nickel could be feasible under appropriate conditions and these were explored through a series of laboratory scale experiments. Laterite samples were reacted at temperatures between 500 and 800°C with an equilibrated mixture of sulfur dioxide, oxygen and nitrogen in a fixed bed reactor. Tests were conducted on saprolitic ore from Bulong, Western Australia, limonitic ore from New Caledonia and garnieritic ore from Indonesia. Nickel extractions were highest from the limonite and relatively low from the other ores. The maximum selective extraction of nickel from the limonite in a single stage sulfation was 73%. Sulfation of other elements present in the laterites was also examined. A two-stage process was also identified which involved sulfation using a strong sulfation potential followed by weaker sulfation potential to attempt to convert ferric sulfate formed in the first stage to ferric oxide. This increased the extraction for the limonite ore to around 84% Ni, 95% Co and 2% Fe. Direct sulfation of laterite could be feasible in locations where sulfide smelting or roasting operations are relatively close to laterite deposits.

Jan 1, 2003

By Jesse White, Arlin Olson

"An Engineering Scale Technology Demonstration (ESTD) unit utilizing the THOR fluidized bed steam reforming technology was built and operated by Hazen Research, Inc. for the purpose of denitrating and solidifying various Department of Energy (DOE) radioactive tank waste surrogates into granular products. The ESTD offered the opportunity to investigate the operational characteristics of two fluidized beds in series to test process system designs such as those for fluidization, feeding, and product collection. Operational characteristics that were evaluated included bed attrition rate, particle growth, and elutriation; and the effects that variations in process parameters (e.g., fluidizing gas flow rate, feed composition, feed injection method, and gas distributor design) had upon these characteristics were observed. Testing of the process systems on this scale allowed for design changes to be made where the cost in time and money were significantly less by comparison to those same modifications being made on the commercial scale.IntroductionFluidized bed steam reforming (FBSR) offers a moderate temperature (620-750°C) continuous method by which various liquid wastes can be processed irrespective of whether they contain organics, nitrates, sulfates/sulfides, chlorides, fluorides, volatile radionuclides or other aqueous components. The FBSR technology has exhibited the potential to process these wastes into either a carbonate or crystalline ceramic (mineral) granular product.Pilot scale testing was performed using the THOR Treatment Technologies, LLC (ITT) FBSR process, as it offered the opportunity to evaluate multiple aspects in an environment more conducive to experimentation. Process changes and system modifications could be made faster and with less cost impact as compared with changes to an assembled commercial plant. These aspects include verification of process chemistry and kinetics, evaluation of materials of construction, equipment sizing and design, and the interactions of the systems. Evaluation of process chemistry allowed for the verification of thermodynamic and kinetic models, and was used in conjunction with these models to improve the database and modeling assumptions. It also allowed for the reevaluation of data from earlier bench scale testing with the opportunity for long-term operations. These long-term effects may include the buildup of one or more elements that results in the formation of eutectics leading to the destabilization of a fluidized bed, or the shift in particle size as a result of attrition or agglomeration. The pilot plant also provided an environment to evaluate materials of construction."

Jan 1, 2014