Search Documents

By Rodney L. Williamson

Vacuum arc remelting (V AR) is an industrial metallurgical process widely used throughout the specialty metals industry to cast large alloy ingots. Part of the V AR control problem consists of adjusting arc current to control electrode melt rate which also depends on the electrode temperature distribution. Because the temperature distribution responds very slowly (1-4 hours depending on size and material) to changes in melt power, the melt rate response is history dependent and highly nonlinear. The situation is complicated further because measurement of the electrode temperature distribution is not practical. To solve the problem of accurate, responsive melt rate control. a low order electrode melting model has been developed and incorporated into a V AR process controller. Data from laboratory and industrial tests show that the goal of responsive, accurate melt rate control has been achieved, even when melting under highly dynamic process conditions. Keywords: Vacuum Arc Remelting. Model-Based Control

Jan 1, 2003

By Carlos Maurício F. Vieira, Lázaro A. Pizatto, Marcus Paulo Cardoso, Sergio Neves Monteiro, Joao Victor C. Nunes, Gustavo S. R. Matheus, Frederico M. Margem

The interest in composites with natural fibers is due, among other factors, to the growing worldwide concern with the preservation of environment and renewable raw materials. The natural fibers have many particular properties that make them an attractive alternative to traditional synthetic fibers. The advantages of using these fibers are: low cost, renewability, biodegradability, low toxicity, abundance and specific strength. The searching for new suitable, economically viable and technologically advanced materials justifies the accomplishment of this work that aims at comparing the mechanical behavior of polyester matrix composites with epoxy matrix composites reinforced with hemp fibers Izod impact tested. The specimens with dimensions: 10 63 12.7 mm, made in different volume fractions of fiber: 0–30 vol%. The samples were tested at PANTEC pendulum model XC-50 located at LAMAV/UENF. With this research was possible to analyse the mechanical properties of these two new materials.

Mar 1, 2018

By James Cornwell, John A. Elton

"Thermionic induced reactions and radiation resonance catalysis of aluminum and aluminum oxide materials exposed to microwaves and triboemissions will be described and explained from both a fundamental and practical level. Magnetron operation at distinct operating conditions that generates both plasmon and triboemissive radiation will be explained and the resulting tribochemical and radiation resonance catalytic reactions between aluminum, aluminum oxide, water and graphite will be delineated. The generation of hydrogen from these materials using triboemissive radiation and microwaves will be described, and the application of this methodology for hydrogen based technologies will be discussed.IntroductionProtective Systems Directed Energy RadiationProtective Systems, Inc, has developed a new radiation device called the EMR (Electromagnetic Resonator) that has unique characteristics that separates it from traditional microwave and rf radiation devices. The radiation from the EMR device is generated using a modified electronresonance magnetron with proprietary filters and operating characteristics.Electronic Device Shutoff. When electronic devices such as cell phones, computers, and other IC based electronics are placed within the EMR radiation, these devices become non-functional as long as the EMR beam is active. Upon removal of the EMR radiation the devices either become operational again or become operational after a cold start. The devices are not damaged by the irradiation.Faraday Cage Interaction Effect. When any of the above electronic devices are placed in a Faraday cage and activated within the Faraday cage without EMR radiation, they operate normally. However, these devices will still be rendered inoperative when an EMR beam generated outside the Faraday cage is directed at the electronic."

Jan 1, 2010

By Cong Wang, Siyang Long, Pengcheng Zhang, Haibin Zuo

This paper introduced the research progress of microwave treatment on coal. The mechanics of microwave treatment mainly include thermal effects and non-thermal effects. Thermal effects, which lead to cracks and changes of pore structure, attribute to the selective heating of microwave. Non-thermal effects involve the removal of oxygen functional groups, improvement of coal rank and decomposition of minerals. Therefore, microwave treatment of coal has a lot of potential applications, mainly including drying, desulfurization, improvement of grindability, enhancement of coal-water slurry property and change the combustion and gasification properties.

Jan 1, 2016

By Dietmar Eifler, Marcus Klein, Hendrik Kramer

Conventional methods to characterize the fatigue behavior of metallic materials are very time and cost consuming. That is why the new short-time procedure PHYBALCHT was developed at the Institute of Materials Science and Engineering at the University of Kaiserslautern. This innovative method requires only a planar material surface to perform cyclic force-controlled hardness indentation tests. To characterize the cyclic elastic-plastic behavior of the test material the change of the force-indentation-depth-hysteresis is plotted versus the number of indentation cycles. In accordance to the plastic strain amplitude the indentation-depth width of the hysteresis loop is measured at half minimum force and is called plastic indentation-depth amplitude. Its change as a function of the number of cycles of indentation can be described by power-laws. One of these power-laws contains the hardening-exponentCHT eII, which correlates very well with the amount of cyclic hardening in conventional constant amplitude fatigue tests. To identify heat-treatment-parameters and SAE 52100 TRIP-alloys with high hardening rates as well as their damage tolerance the PHYBALCHT- and PHYBALLIT-method were used. One modified SAE 52100 TRIP-alloy was investigated in detail. The fatigue behavior and the cyclic hardening of the selected SAE 52100 TRIP-alloy was investigated and compared with conventional SAE 52100. Conventional stress-controlled fatigue tests were performed on a servo-hydraulic test system with a frequency of 5 Hz and a load ratio of R = -1. Different rates of cyclic hardening were identified. The size of the nonmetallic inclusions leading to crack initiation and the number of cycles to failure were used to evaluate differences in the damage tolerance capability.

Jan 1, 2015

By Mariana M. Arantes, F. R. Valenzuela-Díaz, Olgun Guven, Vijay K. Rangari, Julyana Santana, Esperidiana Moura

Nowadays, the development of polymeric materials reinforced with residues of vegetal fibers is becoming popular for application in different segments, from the automotive to the civil construction and furniture industry. Vegetal fiber residues may be used as reinforcement of the recycled polymer materials, for instance, to produce foams to packaging or to thermal and acoustic isolation for green building application. This work is focused on the development and characterization of recycled-HDPE/EVA foam reinforced with fiber residues from babassu coconut epicarp. Firstly, composites based on recycled-HDPE/EVA blend reinforced with babassu coconut fiber were obtained by melting extrusion process. The composites were then extruded in a special single screw for foaming. The foam samples were submitted to mechanical tests, density measurement, DSC, TG, and FE-SEM analysis.

Mar 1, 2018

By D. Zhao

High temperature deformation characteristics of austenitic 304L, and martensitic 410 and 416 stainless steels were investigated by conducting compression tests over a wide range of temperatures and strain rates (950-1250 C and 0.001-20 s-1). Flow behaviors of the three alloys were characterized. Optical metallography was performed to determine the as-deformed microstructures. The flow behaviors were related to microstructural phenomena during high temperature deformation. Dynamic recrystallization was responsible for the flow softening. Both dynamic and static recrystallization were operating, and the recrystallized grain size increased with increasing temperature and decreasing strain rate. Strain rate sensitivity was found to increased with increasing temperature and decreasing strain rate. No defects such as cracking and shear bands were observed at those test conditions. Preferred processing conditions can be selected by considering as-deformed microstructure and strain rate sensitivity.

Jan 1, 1994

By S. S. Ibrahim

The left behind material after the combusion of fossel fuel in some power stations in Cairo; weighing tens of tons every years, was investigated. The material called "Fly Ashes" containing 7.5% Ni, 10.0% V and 9.50% Cr; could be considered as a promising source of such valiable elements. As well as the small grain size (050 70 "m) of the material, and besides the complexity of their formation history, hydrometallurgical methods appeared to be the effective technique to deal with. Yet, preconcentration is possible by means of magnetic and gravity separation methods. The end product is assaying 16.60% Ni and 20.2S!; V with weight recovery of about 60.15%.

Jan 1, 1995

By Hideyuki Itou

Municipal wastes are mainly incinerated in Japan. Both bottom ash and fly ash from the incineration treatment are smelted recently to decrease the volume. Direct smelting of municipal wastes is also becoming popular. The smelting treatment generates fly ash which contains concentrated heavy metals such as Zn, Pb and Cu, and the harmfulness is causing concern. The smelter fly ash is mainly landfilled after stabilization. An effective treatment process of the smelter fly ash is required to recover the metals. For the treatment process, an application of chloridizing volatilization technique is considered. Chloridizing volatilization experiments were carried out to determine the effects of various factors on the volatilization behaviors in this study. A pretreated ash was mixed with a main raw material which mainly consists of hematite. Calcium chloride water solution was added into the mixture. The mixture was pelletized, dried and used as samples for the volatilization experiments. The sample was placed in the reaction tube heated in an electric resistance furnace. 5%02-95%N2 gas with controlled humidity was introduced into the reaction tube. Effects of humidity in the carrier gas, addition of calcium chloride and mixed ratio of the ash to the main raw material were investigated on the volatilization of Zn, Cu and Pb. To determine the volatilization behavior, samples were taken from the furnace at specified temperatures on the heating stage. In addition, experiments at specified holding temperatures for 15 minutes with shortened heating time were conducted. The two series of experiments revealed the effect of heating temperature on the volatilization behavior of Zn, Cu, Pb and Cl.

Jan 1, 2006

By Amy Nelson

In the electrolytic production of zinc, cobalt is removed from the zinc electrolyte by cementation with zinc dust prior to electrowinning. Although the thermodynamics for this reaction are favourable, kinetic barriers to cobalt reduction render the method almost useless in practice unless activators such as copper and antimony or arsenic are added. There is a large body of work studying the effect of these additives, yet the mechanism by which they act is still poorly understood. Even when the target conditions are met, zinc dust consumption is excessively high: satisfactory operation requires up to 300 times the stoichiometric amount of zinc dust. The objective of this work is three-fold: (1) to examine the effects of activators and elucidate the characteristics that make a good activator; (2) to identify new additives that could lead to a more efficient purification process; and (3) to test the new additives with synthetic and real electrolyte solutions. The present paper gives a status report on this project.

Jan 1, 1998

By G. Upadhya

Considerable success has been achieved recently in modeling microstructural evolution during solidification of castings bthrough the coupling of macroscopic heat transfer with microscopic solidification kinetics models. However, a complete model for simulation of solidification in complex shaped castings involves: (i) the description of fluid flow, during and after mold filling, coupled with (ii) heat transfer to the mold and surroundings by use of a macro model, followed by (iii) a description of subsequent solidification of liquid metal by use of a micro model for solidification of the alloy under consideration. This paper describes the coupling of solidification kinetics model to a 3D, transient, fully coupled fluid flow and heat transfer model. Coupling between the macremicro models is achieved by using the latent heat method. Micro models for the eutectics of gray, white and ductile iron are discussed. This coupled code has been used for predicting the thermal history and microstructural data for shaped castings. Various applications of the model, including prediction of shrinkage defects, grain density contours, and graylwhite transition region in the casting, are presented for a relatively complex casting geometry.

Jan 1, 1992

By Stavros A. Argyropoulos, Henry H. Hu

"The assimilation of exothermic additions in liquid metals exhibit an array of unique coupled heat, mass and momentum transport phenomena. These phenomena are further complicated by the presence of a moving boundary.This paper describes a) A mathematical model which simulates the complex phenomena, and b) An extensive verification of the mathematical model. The SIMPLER algorithm was employed to solve numerically the pertinent partial differential equations. The computational results indicated that the exothermic heat of mixing led to a rapid increase in temperature around the moving boundary, which produced an enhanced convective flow in the liquid phase. The intensification of fluid flow around the moving boundary resulted in an acceleration of the melting process.Verification of the model was carried out in two contexts. The first was, in a low temperature physical model consisting of ice immersion in different sulfuric acid solutions. In this physical model, both temperature and velocity measurements were carried out. The model results were compared with experimental measurements and they were found to be in excellent agreement. The second context employed high temperatures, involving the assimilation of silicon in high carbon liquid iron. The model was also applied to predict fluid flow, heat and mass transfer for these high temperature experiments and a good agreement was obtained.In addition new dimensionless heat transfer correlations that quantify these complex phenomena will be presented."

Jan 1, 2001

In the new flowsheet for Inco Limited's S02, Abatement Project at the Copper Cliff, Ontario operations, a copper/nickel sulphide flotation concentrate will be flash smelted, then converted to Bessemer matte. As in current practice, this will be slow-cooled and separated into components by magnetic separation and flotation. The copper content will emerge as a chalcocite concentrate (impure Cu2S), containing some nickel. This copper sulphide will be converted to copper metal.

Jan 1, 1993

By J. A. Gonzalez-Dominguez

During the electrorefining of lead by the Betts process, ionic concentration gradients become established within the slimes layer. These gradients contribute to precipitation of secondary products and to gradients in electrode potential applied to slimes filaments, and thereby affect the dissolution of noble impurities. This paper describes the experimental results obtained when a typical lead anode was dissolved under galvanostatic conditions with concurrent interruption of current at preset slimes thicknesses. Reference electrodes were incorporated within the lead anode to follow the potential gradients across the slimes electrolyte. Samples of the slimes electrolyte were withdrawn in-situ and their compositional changes were related to transport processes across the slimes layer. Upon current interruption the anodic overpotential decays, first abruptly (as the uncompensated ohmic drop disappears), and then slowly (due to the presence of a back E.M.F. created by ionic concentration gradients that decay slowly). Current interruption measurements showed that: (A) concentration gradients exist across the slimes layer, (B) inner solution potentials within the slimes layer can be larger than those measured from reference electrodes located in the bulk electrolyte, (C) secondary products can shift the inner solution potential to negative values that reverse upon re-dissolution and (D) ionic diffusion is seen upon current interruption but it is complex and difficult to model due to the presence of processes that can support the passage of internal currents. SEM and X-ray diffraction analysis of the slimes filaments indicated that secondary reactions leading to the formation of Si02 and PbF2 take place (mainly at the anodelslimes interface). The onset of these reactions and their relationship to the Pb-F-Si-H20 Eh-pH diagram are linked to the industrial operation of the Betts process.

Jan 1, 1994

By Rubén J. Sánchez Rodriguez, Carlos M. Fontes Vieira, Carlos E. Gomes Ribeiro

Ornamental compound stone are produced by industry for decades, however, few published studies describe these materials. Brazil has many deposits of stone wastes and a big potential to produce these materials. This work aims to evaluate the chemical resistance of ornamental compound stones produced with marble waste and unsaturated polyester. An adaptation of Annex H of ABNT NBR 13818:97 standard, with reagents commonly used in household products, was used. The results were compared with those obtained for natural stone used in composite production.

Jan 1, 2015

By J. D. Sunderkötter, M. F. Stroosnijder, V. A. C. Haanappel

"TiAI-based intermetallic compounds have attracted considerable interest as structural materials for high-temperature applications due to their low density and substantial mechanical strength at high temperatures. However, one major drawback hindering industrial application arises from the insufficient oxidation resistance at temperatures beyond 700 °C. In the present contribution some general aspects of high temperature oxidation of TiAI-based intermetallics will be presented. This will be followed by a discussion of the influence of alloying elements, in particular niobium, and of the effect of nitrogen in the oxidizing environment on the high temperature oxidation behaviour of such materials.Extended AbstractIntroductionTiAI-based intermetallics are being considered as construction materials for high temperature components, e.g. in aircraft and car engines, due to their low density and substantial mechanical strength at high temperatures, see e.g. [1,2]. The best ductility can be attained with alloys consisting of y-TiAI with around 5-15 vol.% Q2-Ti3AI. However, one major hindrance to industrial application arises from the insufficient oxidation resistance at temperatures beyond 700 aG. In spite of their high aluminium content, TiAI-based intermetallics do not generally form long-lasting protective alumina scales. After longer exposure times the scales, which are initially rich in alumina, deteriorate and scales consisting of mixed alumina and titania predominate, with high growth rates similar to pure titania.It is not the intention of the present paper to present a general overview of the high temperature oxidation behaviour of TiAI based intermetallics, for which the reader is referred to the literature [3,4]. In the present contribution some general aspects of high temperature oxidation of TiAI-based intermetallics will be presented. This will be followed by a discussion of the influence of alloying elements, in particular niobium. The effect of nitrogen in the oxidizing environment on the high temperature oxidation behaviour of these intermetallics will also be considered."

Jan 1, 1996

By M. J. Soria-Aguilar, F. R. Carrillo-Pedroza, S. Preciado-Nuñez

"Dust originated from the Iron Blast Furnace (BF) and the Basic Oxygen Furnace (BOF) containing alkalis and zinc are not completely recycled because due affects the process efficiency. These types of dust represents an economical lost as a consequence of values contents of iron and carbon. Several processes in aqueous media have been developed to treat the steelmaking dust. This work presents a laboratory study for reduce zinc and alkali containing in BF and BOF dust, using different acid and alkaline solutions and oxidants as ozone. The results obtained show that the elimination of zinc and alkalis can vary from 5 % to 80 % depending on the treatment conditions (the solution, the oxidant and the temperature). The dust obtained from this treatment can to be recycling to the steelmaking processes to recovery iron and carbon values.IntroductionEach one of the steel making industry processes generate several sub-products and residues containing useful units of iron, carbon and other elements that are or could be recycled to the productive process. Some of those sub products are the dust from the gas cleaning system of the blast furnace and the dust from BOF reductive process; such dusts are sent to the sedimentary lagoons. The dust represent a lost of 2 % of the total iron and coal mineral’s content feed to the process.The typical iron, carbon and zinc content of the blast furnace dust is approximately 40, 24 and 0.3 % and the content of the BOF dust are 50, 15 and 0.9 % weight respectively, with physics - chemical characteristics that became them susceptible to be agglomerated and feed to the blast furnace. But the high content of zinc does not allow recycling it into the process. At the blast furnace the presence of zinc propitiate the formation of film in the furnace wall; these elements are vaporized in the low section of the cube of the furnace and they are dragged by the gases to the top and condensed again at the cube. Part of these condensed materials strongly adheres to the furnace cover harming it and reducing the empty space of that section, causing eventually a severe perturbation of the ascendant gas flux [1]."

Jan 1, 2008

By Ashish D. Patel, Ramesh S. Minisandram

"Vacuum Arc Remelting (VAR) is the final and, hence, critical melting step for the production of a sound, segregation-free ingot for the manufacture of alloys used in rotating components in aircraft engines. A mathematical model for this process has been developed by the Specialty Metal Processing Consortium (SMPC). The model predicts temperature distribution in the solidifying ingot, flow in the molten metal pool, and the electromagnetic field in the ingot. These predictions may be used to estimate the effect of melting parameters on the pool profile in the ingot. In this paper, typical pool shapes and flow fields during VAR of Alloy 718 and Ti-6Al-4V are presented. The differences in the pool profile are primarily due to vastly different melting conditions. The model predictions are compared to the observed pool shapes from industrial-size VAR ingots.1. IntroductionVacuum Arc Remelting (VAR) is a process in which an electrode is melted in vacuum by the heat from a DC electric arc. Metal droplets from the electrode fall into the molten metal pool, which solidifies in a water-cooled copper crucible to form the ingot, as shown in Figure I. The ingot obtained from VAR is sound, and has superior cleanliness and chemical homogeneity. Hence, the process is the final melting process for most nickel-base superalloys and titanium alloys used in the manufacture of critical rotating components (discs & blades) of aircraft engines. Modeling of this process provides an insight into the effect of melting parameters on the molten metal pool in the solidifying ingot, which is a key first step in process optimization and defect prevention. In this paper, typical pool shapes, both measured and predicted, for VAR of Alloy 718 and Ti-6Al-4Vare presented. Alloy 718 is the most common VAR-processed nickel-base superalloy; whereas Ti-6Al-4V is the ''workhorse"" alloy for titanium-based alloys."

Jan 1, 2004

By Yong-Moo Cheong

When the zirconium pressure tube(PT) is in contact with the calandria tube(CT) in the pressurized heavy water reactor(PHWR), the temperature gradient between the inner and outer wall of the PT results in a thermal diffusion of hydrogen(deuterium) and hydride blisters are formed on the outer surface of the PT. Since Zr-2.5Nb pressure tubes have a high risk for the formation of blisters during their operation in a PHWR, there is a strong incentive to develop a method for the non-destructive detection of the blisters grown on the tube surfaces. However, because there is little mismatch in an acoustic impedance between the hydride blisters and zirconium matrix, it is not easy to distinguish the boundary between the blister and the zirconium matrix with the conventional ultrasonic methods. This study has focused on the development of an ultrasonic method to detect the hydride blisters formed on Zr-2.5Nb pressure tubes. Hydride blisters were grown on the outer surface of a Zr-2.5Nb pressure tube using a cold finger attached to steady state thermal diffusion equipment. Ultrasonic velocity ratio method as well as conventional ultrasonic parameters with an immersion technique was developed to detect small hydride blisters on the Zr-2.5Nb pressure tubes.

Jan 1, 2006

By B. J. Jody

Each year, about 11 million tons of metals (ferrous and nonferrous) are recovered in the U.S. from about 10 million discarded automobiles. The recovered metals account for about 75% of the total weight of the discarded vehicles. The balance of the material or shredder residue, which amounts to about 3 million tons annually, is currently landfilled. The residue contains a diversity of potentially recyclable materials, including polyurethane foams, iron oxides, and certain thermoplastics. This paper discusses a process under development at Argonne National Laboratory to separate and recover the recyclable materials from this waste stream. The process consists essentially of two- stages. First, a physical separation is used to recover the foams and the metal oxides, followed by a chemical process to extract certain thermoplastics. The status of the technology is discussed, and the process economics are reviewed.

Jan 1, 1994