Search Documents

By G. Cifuentes

When the applied current is interrupted in a copper electrowinning plant, and then is back in operation, the lead anodes tend to corrode. In order to decrease the corrosion, the damage protective ("back up") anodic currents are applied during the period of interruption. The current work aims to establish the effect of the concentrations of sulphuric acid, copper and cobalt on the anode corrosion, to quantify the effect of various anodic protection levels on the anode corrosion and to propose a method to select the appropriate protective current density value.

Jan 1, 1999

By Mariana Barcelos, Frederico Muylaert Margem, Giulio Rodrigues Altoé, Pedro Amoy Netto, André Gomes, Sergio Neves Monteiro

Environmentally correct composites, made from natural fibers, are among the most investigated and applied today. In this paper, we investigate the mechanical behavior of polyester matrix composites reinforced with continuous fique fibers, through bending tensile tests. Specimens containing 0, 10, 20 and 30% in volume of fique fiber were aligned along the entire length of a mold to create plates of these composites, those plates were cut following the ASTM standard to obtained bending tests specimens. The test was conducted in a Instron Machine and the fractured specimens were analyzed by SEM, the results showed the increase in the materials tensile properties with the increase of fiber amount.

Jan 1, 2015

By C. E. M. Meskers

End-of-life Electronic and Electrical Equipment, o_cially called WEEE, is unjustly regarded as mainly a waste management problem. What is structurally overlooked is the enormous resource impact of these devices. EEE rep- resents a tremendous metal resource, which should be uti- lized through e_ective recycling, which has a much lower environmental footprint than primary production. The actual amount of end-of-life EEE recycled today is embar- rassingly low since insu_cient EEE is collected and part of the collected EEE is exported to developing countries, where it is largely not entering o_cial recycling systems. To achieve a global recycling society issues like technol- ogy, economics, life cycle structure, stakeholder aware- ness and legislation have to be addressed in a global, co-operative manner so that sustainable closed product cycles can be obtained. Requirements for a "global re- cycling society" are de_ned to address today's reality of global ows of used consumer products, taking into ac- count the likely needs of the future.

Jan 1, 2009

By Robert E. Brown

Magnesium recycling has been used to recover both new scrap and old scrap. It was used extensively in Germany during WWII to expand the magnesium supply. There were a large number of magnesium recyclers in the US who got their start smelting old scrap, old airplanes and old waste dumps from the WWII build up. As the world magnesium industry dwindled, only a few companies were left that did magnesium recycling as a primary business. The sand foundries tended to recycle of their production scrap in their melting furnaces. Even the original die casters tended to put scrap directly back into melting furnaces at the die casting machines. As high purity alloys were developed and the use of die castings in automotive work increased, the tendency was to let the magnesium recyclers convert the scrap back to high quality ingot. Automotive use has grown because of the low density of magnesium. This property is the one of the biggest problems to overcome in shipping scrap. Gates and runners from die casting are very irregular shapes and it is very hard to load a truck with enough material to get a low shipping cost per pound. Recent new equipment companies have developed magnesium equipment that is specifically designed to recycle, refine and cast secondary magnesium metal. These melt cells are supplied as integrated units to magnesium casting sites. The cost and effectiveness of this approach will be discussed.

Jan 1, 2000

By Helga Larravide

A new on-line database of literature about copper has been created through a joint undertaking by the Copper Development Association Inc. and PROCOBRE-Chile, with funding provided in part through the International Copper Association, Ltd. The new database will permit Spanish-speaking technologists to access publications maintained by PROCOBRE-Chile by means of standard keyword searches. In addition, a new Spanish- English thesaurus has been written to enable Spanish-speaking individuals to search d access the Technology and Environmental databases of the Copper Data Center, which together comprise more than 80,000 publications dealing with the production, properties, uses and environmental effects of copper. Planned expansion of the new Spanish literature database is described.

Jan 1, 1999

By T. T. Chen

Raw anode slimes consisting primarily of PbSO4, AgCuSe, Cu3Se2, Cu2-x Se, Cu2O, CuSO4.5H2O, Sn arsenate and Sb-Bi-As oxide are batch-leached with electrolyte-O2 to dissolve Cu. During this process, Cu2O and CuSO4.5H2O are solubilized and the Cu in the selenides is leached with the formation of Ag2Se and Se. A small amount of Cu remains in the Ag2Se, Sn arsenate and Sb-Bi-As oxide. The decopperized slimes are repulped in Na2CO3 solution to convert most of the PbSO4 to NaPb2(CO3)2(OH). The Sn arsenate and Sb-Bi-As oxide partly react, but the Ag2Se is not significantly affected by the Na2CO3 solution. The NaPb2(CO3)2(OH) intermediate phase is dissolved in acetic acid to leave a final product consisting of Ag2Se, Se, Sn arsenate and Sb-Bi-As oxide, together with small amounts of PbSO4, NaPb2(CO3)2(OH) and various gangue constituents.

Jan 1, 1993

By Christian Bernhard, Mario Hartl, Susanne K. Michelic

"One aspect of an efficient process and product optimization of the liquid steelmaking process is the understanding of reactions and interactions between the components steel, slag and nonmetallic inclusions. The present paper focuses on a fundamental study of this topic by combining the powerful methods of thermodynamic modeling with systematic experiments on a laboratory scale and subsequent SEM/EDS analyses. The modeling aspect is addressed by the commercial software FactSage 6.1; laboratory experiments are performed for a low-alloyed, Ca-treated carbon steel combined with varying slag compositions. The consequent SEM/EDS analyses provide a detailed insight into the inclusion landscape which offers a strong tool for characterizing the modification of inclusions. In the present study the combination of these methods is mainly applied to oxides, due to their crucial influence on the final product quality, thus giving important indications for further optimizing the secondary metallurgy processes.IntroductionIn recent years, the range of application for steels has been enlarged continuously; also resulting in extreme surrounding conditions combined with considerable stresses for the material. This trend is directly linked with higher demands on the properties of steels. In order to optimize the final product quality, the cleanness of steels is an important criterion. For this reason, the broad topic ""Steel Cleanness"" has become one of the main research points at the Chair of Metallurgy. Next to the continuous optimization of methods for the characterization of cleanness, the primary aim is to combine thermodynamic modeling and laboratory experiments in order to describe the changes in inclusion landscape under different conditions.The steel cleanness can particularly be influenced in the processes of secondary metallurgy. In different processes the reactions and interactions between the components steel, slag and nonmetallic inclusions (NMI) are essential for the final inclusion landscape. Consequently, the understanding of the occurring reactions is a fundamental aspect for further development and process optimization. In secondary metallurgy especially oxide-slag systems consisting of the components Ca0-Ah03-Mg0-Si02, which significantly influence the modification of NMI, are of importance. Several works dealing with the interactions of oxide non-metallic inclusions with different slag systems have been published in the last years [1-4]. In order to observe the dissolution of oxides in different slag compositions a Laser Scanning Electron Microscope is frequently used. A very detailed study on the ternary system Ah03-Ca0-Mg0 and its subsystems was also done by De Aza et al. [5, 6]."

Jan 1, 2011

By Samantha Moodley, Rauf Hurman Eric, Cevat Kucukkaragoz, Aditya Kale

"Two titania slags, rutile and synthetic rutile were chlorinated with petroleum coke and CO in a small bubbling fluidized bed reactor. The study aims to identify differences in chlorination mechanism, compare conversion rates, blowover and the chlorination of impurities for the various titania feedstocks at different temperatures.Chlorination rates were highest at 1000ºC; rutile chlorination significantly increases as temperature increases from 800ºC to 1000ºC. At 1000ºC, synthetic rutile had the highest chlorination conversion rate; this was followed by Slag B which in turn was more reactive than Slag A and rutile. The mechanism for slag, synthetic rutile (SR) and rutile chlorination differs. Synthetic rutile feed is porous, providing a larger surface area for the chlorination reaction, hence the highest conversion rates was attained. Titania slag becomes porous with the initial chlorination of FeO and MnO whilst rutile remains solid. As the porosity of slag particles increases so does its tendency to be elutriated. Ti2O3 is oxidized within the early stages of chlorination during the chlorination of FeO and MnO. Ti2O3 not oxidized is then rapidly chlorinated.IntroductionTitanium dioxide (TiO2) is the most common compound of titanium, about 95 - 98% of extracted titanium minerals is processed into TiO2 white pigment [1]. Two processing routes exist for the production of TiO2 pigments, i.e., sulphate and chloride based processes. In the chloride process, titania feedstock is fed to a fluidized bed reactor together with reductant and chlorine gas. A temperature of 1000 - 1300ºC is maintained in the reaction zone and apart from silica, zirconia, uranium and thorium, virtually all the metal oxides in the feed are converted to their respective chlorides [2]. Chlorine is recovered and recycled back to the reactor."

Jan 1, 2012

By Karl A. Gschneidner

Magnetic refrigeration was first used in the mid-1920's and new developments seem to have taken place about every 20 years, and this is especially true for the mid-1990's. The active magnetic regenerator magnetic refrigerator has the promise to become the first practical machine utilizing the magnetocaloric effect for cooling (and also heating). The basic principles are briefly discussed. Since the temperature lift for the magnetocaloric effect spans about 50 K, one will need to utilize several ferromagnets with different magnetic ordering temperatures in order to reach temperatures below ~250 K. The basic properties, behaviors, limitations, and new phenomena and knowledge are discussed.

Jan 1, 1997

By Lu-ming Zhao, Li Zhao, Yu Wang

Mould flux is a vital functional material which is based on silicate including flux and framework material. The effects of magnetic field intensity and frequency on viscosity of mould flux were tested by rotational viscosity tester and a measurement device for electromagnetic characteristics of mould flux viscosity under high temperature conditions. The results show that: with the magnetic field intensity rising (0 –30 mT), the viscosity of mould flux increases by 1.3–1.8 P. With the frequency rising (6–12 Hz), the viscosity of mould flux is increased by 1.2–1.4 P. When the binary basicity is 1.08, the viscous flow activation energy increases with the increase of the magnetic field intensity and frequency. It can be the main reason for the increase of mould flux viscosity that the electromagnetic forces disrupt the ordered structure of mould flux and make the ion migration rate increase.

Mar 1, 2018

By Kiyoshi Takai

The Para-Eco Incinerator Ash Processing System for cleaning slag has been developed after a seven-year pilot plant study. The major part of the system is an electric furnace heated to 1773 K. The feed material consists of a municipal solid waste incinerator ash mixture containing a reducing agent of a coke and an inorganic flux of calcium and magnesium. With this furnace system, three kinds of products are produced. They are an inorganic molten salt that is slag, molten iron alloy absorbing non-ferrous metals, and fly ash. Due to the reducing atmosphere in the furnace, the slag does not contain any metal components as well as chlorine components just like natural rock and/or aggregate. A retreatment plant modifies this slag into a practically useful aggregate. The plant consists of a slow cooling step for crystallizing the slag as well as a water granulation step. The iron components in the ash are reduced to molten iron droplets, which concentrate at the furnace bottom. The non-ferrous metal components such as copper, chromium, and others are absorbed into the molten iron but not into the molten slag. Volatile metals such as lead, zinc, cadmium and others as well as sodium, potassium, and chlorine go back into the fly ash. A solvent extraction method and/or other appropriate procedures can be used to extract the metal components from this fly ash.

Jan 1, 2003

By Han Yihua, Zhang Caijun, Zhu Liguang, Zhang Qingjun, Wang Shuoming, Wang Yan

An industrial test on 210 t converter-LF-CC production line on high heat input welding shipbuilding structure steel DH36 has been taken in a factory in north China, the effect of adding microalloy elements V and Mg on casting billet microstructure has been researched. It was found that when the composition of V was between 0.03 and 0.05% and the composition of Mg was between 0.002 and 0.005%, a large number of acicular ferrite precipitate in austenitic crystal in as-cast structure and cross into a net structure. The inclusions size which induced intra-granular ferrite are mainly less than 4 lm, especially those between 2 and 3 lm account for 50.80%, in these inclusions the composite inclusions mixed with Mg accounted for more than 60%.

Mar 1, 2017

By Xiping Chen, Wangxing Li, Jiemi Zhou

"Desulfurization methods suitable for anode-grade petroleum coke (coke for short) used in primary aluminum industry are coke desulfurization during calcination, desulfurization in soakage and desulfurization in mediums. Coke desulfurization during calcination is discussed in this paper. Influences of calcination temperature, holding time and coke granularity on coke desulfurization were discussed. Experimental results show that calcination temperature has a remarkable influence on coke desulfurization. When the temperature is high enough desulfurization ratio of coke can reach 85% only by calcination. Holding time has a definite influence on coke desulfurization, but desulfurization ratio is low at the temperature of 900~1300°C. The influence of holding time is obvious when calcination temperature surpasses 1400°C. The influence of coke granularity is smaller compared with calcination temperature and holding time.IntroductionPetroleum coke is main raw material for carbon anode in primary aluminum industry, and its weight percentage in carbon anode is about seven percent. Green coke can not be directly used for anode production because of its immanent moisture and volatiles. Green coke must be calcined in order to meet the request of anode production. Calcination is a heat-treatment process during which green coke is heated to a given temperature to remove volatiles, moisture and some sulfur. Real density, strength, electrical conductivity and anti-oxidation ability of petroleum coke can be improved by calcination and calcined coke can be received [1, 3, 4]. Sulfur in calcined coke finally goes into carbon anode. During baking or aluminum smelting, the sulfur in anode ultimately changes into SO2 and emits from anode into the atmosphere. Excess SO2 easily leads to acid rain which brings heavy pollution to the environment [1, 2]. With the development of Chinese aluminum industry, consumption of anode-grade petroleum coke increases year by year, the total consumption in 2007 surpassed 4.5 million tones and the yearly emission of SO2 from aluminum smelters has exceeded 270 kilotones. From 2005 Chinese government began to limit the emission of SO2 from primary aluminum industry, so desulfurization of anode-grade petroleum coke becomes more and more urgent. Some relationship need to be found and used to guide desulfurization of petroleum coke."

Jan 1, 2008

By Tuula Mäkinen

In 1959 Outokumpu started up an integrated nickel smelter and refinery at Harjavalta. The flash smelting ? Peirce-Smith converting route was applied, and the high-grade converter matte was further refined to nickel cathodes by leaching and electrowinning. In 1995 the production capacity was increased from 17 000 mtpa to 52 000 mtpa, based on the Direct Outokumpu Nickel Smelting Process. The additional refinery capacity is based on hydrogen pressure reduction, producing nickel powder and briquettes. The smelting operation is currently part of Boliden Group and the nickel refinery part of OM Group. In the DON technology, high-grade nickel matte with low iron content is produced in the flash smelting furnace directly without subsequent converting. The metal values in the smelting slag are recovered in an electric furnace as an iron containing Ni-matte. The mattes produced differ from the conventional nickel mattes in many respects, and therefore focused R&D efforts have been made in order to cope with their melting points, fluidities and settling properties. When developing and operating metallurgical processes it is crucial to manage and control the characteristics of the products as well as by-products generated in different steps of the process chain. The low melting points of the high-grade nickel mattes produced in the DON furnace, particularly those low in copper, have pointed out challenges in the furnace design, in particular in the hearth and its thermal engineering. Also key issues of the DON technology are smelting of high-magnesia concentrates, the recoveries of nickel and copper, as well as those of PGM`s and cobalt. These factors can be affected by a proper selection of the process concept, and the operational conditions in the processing vessels. This paper deals with the experience of the DON technology gained over the first ten years of operation, including the significant environmental impacts. Selected results of the thermo-dynamic modelling of DON and EF mattes and high-magnesia slags are reviewed, with the reference to the mattes produced. Also the design principles of the FSF and EF will be discussed.

Jan 1, 2006

By Minting Li, Hailong Yang, ChangWei, Cunxiong Li, Gang Fan, Xingbin Li, ZhiganDeng

The filtration problems on acid leaching sludge of high silicon zinc ore have been paid extensive attention in zinc hydrometallurgy. It was found that soluble silica can be effectively converted into silica precipitate with good settling, filtration and washing properties, and the filtration rate can be in excess of 800 L/m2 · h under certain leaching conditions. According to investigating on the filtration rate, viscosity and concentration of silica of leaching sludge or liquor, the filtering temperature can tremendously improve the filtration property of pulp. At the same time, the experimental data indicated that the viscosity of leaching liquor was the key factor influencing filtration property of leaching sludge.

Jan 1, 2016

By Alicia Esther Ares

The family of Zn-Al (ZA), Zn-Ag and Zn-Al-Ag (ZINAG) alloys offers high mechanical properties, ease of finishing, the advantage of low energy and pollution-free melting. Also, present alternatives to the well developed alloy systems, such as brasses, bronzes, cast irons and aluminum alloys. The main objective of this paper is to measure thermal parameters in ZA, Zn-Ag and ZINAG hypoeutectic and hypereutectic alloys directionally solidified which present columnar, equiaxed and columnar to equiaxed transition structures (CET). Also, estimate the mechanical properties, such as microhardness and tensile parameters and correlate these with the thermal (cooling rate) and structural parameters (grain size and dendritic spacing). The different types of structures were analyzed with optical and scanning electron microscopy. The results showed the influence of concentration, microstructural arrangement and thermal conditions during solidification on the mechanical properties. The results of the present investigation are compared with previous experiments.

Jan 1, 2010

By Cameron Harris

With the consolidation of the copper industry in the second half of the 20th century resulting in fewer plants treating ever increasing quantities and qualities of feed, the enormous flexibility of the Noranda Process gives it significant advantages over many competing technologies for the production of matte. Toll smelting, recycling, and secondaries treatment will become the cornerstone of profitable operations for all but the lucky few who have large captive mines associated with the smelter. Consequently, the ability to respond to changing market conditions without significant metallurgical or operational upsets will be of considerable commercial advantage. The inherent stability of this bath-smelting process leads to tight matte grade control, while the bath turbulence leads to rapid consumption of feeds with widely varying physical characteristics. Low capital and operating costs combined with a layout suitable for retrofit into existing converter aisles makes it a sensible choice for parts of the world still experiencing the aforementioned consolidation, which is essentially complete in fully developed economies such as the United States of America and the European Union. This paper will discuss features of the Noranda process compared with other technologies and its place in the future global copper production industry, which is set to become increasingly competitive and aggressive.

Jan 1, 2002

By P. Hanniala

In the day-to-day life the copper business of today is influenced directly by the ever-increasing general concern about the environment. In addition to that the inherent shortcomings of the copper smelting business, have since many years been the falling real price level of the metals and the relatively high initial capital investments required for the production units. These shortcomings have been compensated for by high productivity, low specific operating costs, low metal inventory and unbeatable technological superiority. Thus today more than 50 % of the world primary copper is today produced by utilizing Outokumpu Flash Smelting Technology. This figure is expected to grow at an increasing speed in the near future. Characteristic for the Outokumpu Flash Smelting technology is high flexibility for a wide grade of concentrates and the highest sulfur capture owing to at the same time competitive investment and operational costs. The Flash Converting technology offers new options for copper production and optimization of the mine- concentrator-smelter production chain. In the following years it is expected that the trend in copper making is that higher grade concentrates are produced at the mines. Thus increasing amount of high grade concentrate will be available for direct-to- blister Flash Smelting causing an overall cost reduction in copper smelting i.e. both in capital and operational costs. In the '90s new technologies based on Outokumpu Flash Smelting technology have been taken into operation, thus eliminating the non-continuous Peirce-Smith converting process step. New innovative solutions have been used in the latest projects, as in Kennecott Utah Copper, where the new Kennecott-Outokumpu Flash Converting process was started up in 1995. Also, in 1995 the new DON process was started at Outokumpu Harjavalta nickel smelter followed by the Fortaleza nickel smelter in Brazil in 1997. The aim of the continuous development work at Outokumpu has been the expansion of the direct-to-blister process towards lower grade concentrates. The most recent example of this is the start-up at the Olympic Dam smelter in Australia, where the existing direct-to-blister Flash Smelting furnace was replaced with a new one having a capacity of 200 000 t blister copper per annum in just one smelting step.

Jan 1, 1999

By Junji Shibata

Heavier rare earth, which is contained in a small amount in ores such as bastnesite and monazite, has been accumulated as a heavier rare earth residue without doing separation and purification due to the lack of suitable methods. The heavier rare earth residue includes seven rare earth elements such as Tb, Dy, Ho, Y, Er, Tm and Yb. Separation and recovery process of Dy, Y, Tm and Yb from leached solution of the heavier rare earth residue was investigated by using a column method with solvent impregnated resin. The solvent impregnated resin was prepared by impregnation of organophosphorous extractant whose trade name is PC-88A into a macro porous resin, Amberlite XAD-7. It was almost impossible to separate them in simple adosorption and elution steps. However, we attained to individually separate Dy, Y, Tm and Yb from the leached solution first by changing eluent concentration gradually from pH2 to 0.02kmol/m3 HC1 in the elution step, and secondly by using a development column and changing eluerit concentration in the elution step. The separation process flow was proposed for a heavier rare earth residue by using the solvent impregnated resin method.

Jan 1, 1998

By Hiroshi Tabuchi, Akihiko Takahashi

"High strength aluminum matrix composites were prepared and studied using as reinforcement newly developed nearly mono-dispersed a-alumina single crystal particles each of which has a regular polyhedral shape. The composites were formed by centrifugal casting using aluminum casting alloys (Al-Si and Al-Cu-Mg) as the matrices, followed by heat treatment. The volume fraction of the alumina particles was as high as 60%. The same matrix composites reinforced by conventional crushed fused alumina particles were similarly prepared as the reference. The bending strength and tensile strength of the Al-Cu-Mg matrix composites reinforced by the novel alumina particles of 10 µm in average diameter are as high as 1020 MPa and 560 MPa, respectively, which are higher than those of the conventional alumina composites. Furthermore, the bending strength of the novel alumina composites degraded less than that of the conventional alumina composites after thermal fatigue tests. The number of cracks in the matrix seemed to influence the thermal fatigue property because many cracks were observed in the conventional alumina composites, whereas only a few cracks were observed in the novel alumina composites. This was confirmed by SEM observation of the sample composites before and after the thermal fatigue tests.IntroductionAluminum matrix composites strengthened by dispersed reinforcements are of interest for various applications due to their improved properties, such as high specific strength and stiffness, wear resistance, etc .. A large number of investigations have been made concerning fabrication processes and properties of these composites. With regard to the fabrication processes, powder metallurgy has been well-known as a solid phase process, and recently many liquid phase processes such as a compocasting, a squeeze casting, the Lanxide process, and the Osprey process have been studied and developed.(1)"

Jan 1, 1998