Search Documents

By Dexter G. Mendoza

To analyze the behavior of minor elements in the copper smelting process, the phase relations and the activities of arsenic and antimony in the miscibility gap of Cu-Fe-S-X (X = As or Sb) system have been determined at 1473K by the quenching method and the double Knudsen cell- mass spectrometric method, respectively. The experiments have been conducted for the charges in the miscibility gap with different mass%Fe/mass%Cu ratios with varying arsenic or antimony content. The activity measurements indicate that the arsenic activities in both the metal and matte phases show extremely negative deviation from the ideal behavior. The Raoultian activity coefficients at infinite dilution in the metal and matte phases are found to be almost constant against the charges in the miscibility gap, and they are 4.3 x 10-3 and 5.5 x 10-2 for the metal and matte phases, respectively. Moreover, the activity measurements of antimony show an activity value larger than that of arsenic but it still deviates negatively from Raoult's law. The activity coefficients of antimony at infinite dilution are found to be 1.2 x and 2.2 x 10-1 for the metal and matte phases, respectively. The vapor pressures of the predominant As, AS2, AsS, Sb, Sb2, and SbS species in the gas phases of arsenic and antimony, respectively, equilibrated with the immiscible solutions have been calculated on the basis of the determined activity coefficients and they are very small at less than 1 Pa, even when their contents in the metal phase are increased up to 10 mass%.

Jan 1, 2002

By Xue Ping

Sm2Fe17 alloy is an important precursor for the preparation of Sm2Fe17Nx magnet, which possesses a higher Curie temperature, larger anisotropy field, better resistance to oxidation and thermal stability. In this paper, the wet chemical co-precipitation was developed for synthesis of the Sm-Fe alloy oxide precursor. Based on the principles of simultaneous equilibrium and mass balance, a series of thermodynamic equilibrium equations of Sm(III)-Fe(II)-NH3-C2O4 2--H2O system at ambient temperature were deduced theoretically and the thermodynamic diagrams of lg[M2+]T (M=Sm, Fe) versus pH at different solution compositions were drawn. Then, the experiments were done to address the various effects on the wet chemical process, including solution pH value, reactant concentration, reaction temperature and aging time, etc. It is found that by precise control of the process, the Sm-Fe alloy oxide precursor was synthesized with fine crystallization and special size &size distribution.

Jan 1, 2008

By Antonio Huerta

The effects of potassium ethyl xanthate collector and potassium dichromate used as a depressor on a PbS mineral were studied by high frequency impedance technique. Measurements of complex permittivity, at 100 MHz suggested that is possible to obtain from isotherm adsorption the adequate industrial collector concentration being this in the range of lE-3 to 5E-3M of KEX. The e' values (320-420) in the PbS-KEX system was increased as the KEX concentration was lowered). In the other hand the PbS- K2Cr2O7 system showed higher values of e' (420-510) as the K2Cr2O7 concentration was increased. The PbS-KEX-K2Cr2O7 system was evaluated.

Jan 1, 1997

Mineralogical and metallurgical scoping testwork were carried out to investigate the production of separate, marketable gold and platinum concentrates. The study utilized a flotation concentrate assaying approximately 5 wt% gold and 5 grams per tonne platinum. The gold-platinum mineralization was recovered from a placer deposit. Optical microscopy and scanning electron microscopy with energy dispersive x-ray analysis identified gold as zoned Au- Ag and Au-Ag-Cu alloys. Platinum primarily occurred as weakly zoned, variably magnetic Pt- Pd-Fe alloys. A combination of gravity and magnetic separations resulted in a gold concentrate grading 86.9 wt% Au (and 9.lwt% Ag) and a separate platinum concentrate grading 400 g/t Pt with recoveries of 94.5% and 96.7%, respectively. Magnetohydrostatic separation (MHS) using the Magstream 200 Separator indicated promising results.

Jan 1, 1994

By C. Lupi

The electrorefining of primary copper is a well known technology: in this work copper scrap was directly processed in the same way. he copper and copper alloy scrap was previously pressed by means of a 20 tons apparatus in order to avoid pyrometallurgical operations. The samples obtained in this manner showed a good compactness so that they were used as anodes in the electrorefining tests. The tests were carried out on anodes made by copper scrap, copper alloy scrap and a mixture of the two. The electrorefining tests were performed at both 303 and 333 K, in a perspex cell having a volume of 500 ml using a current density of 250 A/m2. The cathode used was always a sheet of pure copper and the electrolyte composition was 40-50 g/l Cu as CuS04 and 150-200 g/l H2SO4. Current efficiency in the range of 92-97% and specific energy consumption ranging from 0.14- 0.20 kWg of copper were reached in all the tests. The refined copper deposits were analyzed by AAS to verify their purity and observed by SEM to highlight their morphology.

Jan 1, 1998

By M. G. Silva-Valenzuela, H. Wiebeck, F. R. Valenzuela-Diaz, J. C. Arjona, S. H. Wang

Urea is the most used nitrogen fertilizer around the world being responsible for many environmental problems. Preparation of microcapsules from biodegradable polymer has been reported as a main system to sustain active substances, finding application in different areas. The objective of this work was to sustain urea in nanocomposite microcapsules of poly(3-hidroxybutyrate) (PHB) reinforced with a smectite Brazilian clay in its natural (MMT) and modified (OMMT) form. PHB/MMT and PHB/OMMT microcapsules were obtained by w/o/w emulsion. Characterization were performed by XRD and optical microscopy. Structural and morphological differences observed by XRD and optical microscopy shown that PHB/OMMT microcapsules are smaller than PHB/MMT microcapsules, with average size diameter ranging * 49 μm. Results indicate that PHB/OMMT microcapsules present more defects and fractures than PHB/MMT microcapsules.

Mar 1, 2018

By Robert Kozicki, Eric Graham, George Wrightson

"IntroductionThe manufacture of Ferro Chromium involves the smelting of various ores and fluxes to produce the metallic product.Slag is inherent in the process. It has a much lower density than the metallic FeCr. Some chrome may be trapped in the slag as either FeCr or Cr203.Previous methods to estimate the slag in the FeCr have revolved around separating the slag and metallic portions by exploiting the differences in density. The downside with that procedure is that material will often contain pieces that are adhered FeCr and slag. The Metallic FeCr may also be completely encapsulated in the slag.An alternative and more precise method involves calculating the slag content based on chemical analysis of Mg and Al. The Mg and Al will be at relatively low levels (less than 0.1 % ) in the Metallic FeCr pieces and considerably higher in the slag (3% or greater). The overall sample will have a proportional amount and is calculated using simultaneous equations with the assumption there is only one kind of slag and one kind ofFeCr present. ""Pure"" slag and ""pure"" FeCr are needed in order to determine the Mg and Al in each. The detemlination of the Mg and Al in the overall sample would then be used to calculate the amount of slag.When the particle size is small, it is difficult to sample and get ""pure"" pieces of the slag and FeCr of sufficient quantity to perform a proper analysis. Often, historic data is used but that is dependent on the source of the FeCr and the materials used in its production. Mg and Al levels in slag can vary between 3% and 20% in different FeCr slags depending on their origin."

Jan 1, 2013

By S. Jolivet, A. Klöfverskjöld, P. Latostenmaa, B. P. Wilson, M. Lundström, P. Halli

Doré slag is secondary product of copper electrore fining anode slime treatment. The slag consists mainly of different slag formers, such as borax and silica based minerals together with soda and traces of sealing materials. However, Doré slag also contains metals present in the anode slime, such as Ag, Cu, Bi, Sb and Te. At some plants, slag cleaning has been conducted utilizing conventional grinding and flotation circuits in order to enrich the content of precious metals in the slag [1]. Nevertheless, the routine consideration of the slag as a secondary raw material has so far not been adopted on an industrial scale. The current study presents the preliminary results of the nitric acid and chloride leaching of antimony from Doré slag. Chemical and mineralogical analyses (SEM-EDS, AAS, XRD) were performed for the raw material, leaching residue, and leaching solution in order to ascertain the metal recovery and kinetics during leaching.

Mar 1, 2017

By N. L. Piret

Primary and secondary copper smelting dusts are being generated in varying quantities with very dissimilar characteristics due to the different compositions of feed materials and the type of process utilized. After categorizing the multitude of dust types, the criteria for on-site and off-site recycling of smelter dust in terms of type and concentrations of the accompanying elements are established. Thereby, consideration is given to the important aspects of: ? optimization of copper recovery ? quality of copper product ? valorization of accompanying elements ? elimination and disposal of deleterious impurities ? minimization of impact on operation ? effects on operating costs ? environmental impact of dust treatment on overall process Existing commercial, emerging and proposed copper smelting dusts, pyrometallurgical as well as hydrometallurgical, treatment schemes are reviewed and evaluated technically, economically and environmentally in an attempt to streamline the vast number of proposed options. Thereby, the high selectivity achievable in hydrometallurgical dust processing due to it being complementary to the smelting process is expected to be given increased consideration.

Jan 1, 1995

By Mansoor Barati, Yindong Yang, Yonggang Wei, Bo Li, Alexander McLean

Reduction roasting followed by magnetic separation is an important method for treating laterite nickel ores. In this work, garnierite type laterite ore from Yunnan province in China was reduced by methane under different conditions followed by magnetic separation to obtain the ferronickel concentrate. The phase and microstructure transformations of garnierite in the reduction process were investigated using XRD and SEM-EDS. The experimental results showed that reduction temperature from 873 to 1173 K had only a small effect on content and recovery of nickel and iron. The content and recovery of nickel and iron in the concentrates increased slightly with prolonging reduction time. In addition, the nickel and iron content decreased with increasing methane concentration, but the recovery of nickel and iron increases. A decrease in the iron content and recovery were observed when the dosage of sodium sulfate varied from 5 to 20% at a temperature of 1073 K and reducing time of 90 min, while the nickel content and recovery gradually increased.

Mar 1, 2018

By Scott A. Shuey

Keywords: E-Waste, Pyrometallurgy Many might think addressing the issue of e-waste is a new area of study. Electronics disposal has been discussed in some circles for at least the past 25 years. The recycling of electronic waste (e-waste) tends to be a rather complex undertaking when considering the intimate bonding of materials in the average printed circuit board. The development of a recycling process is further complicated when considering the wide variety of products being generated under the heading of ?electronics.? Focusing only on the primary constituents (polymers, Cu, Al, Fe, etc.) tends to lead one to fairly simple flowsheets. Ignoring trace elements, and the various halide species generated, will lead process engineers down a development path that is sure to cause material handling issues. Researchers at Colorado School of Mines are modeling the complex chemistry that exists within the body of e-waste?comprising 39 of the known elements. An understanding of the systems thermodynamic behavior will result in the development of a more robust, long-term process for the recovery of valuable materials from the e-waste stream.

Jan 1, 2005

By Othon do Rêgo Monteiro Neto

[The present study has investigated the extraction of copper from a chalcopyrite flotation concentrate using an adapted strain of Thiobacillus ferrooxidans and shake flasks, tank leaching and Warburg respirometer techniques. From the shake flask experiments, the activation energy and the frequency factor have been determined to be ?ka = 59.4 kJ and A = 3.3 x 105 S-1, respectively. The temperature coefficient was found to be Q10 = 2.2 in the range of 20 to 35°C. It was suggested that the reaction mechanism of chalcopyrite leaching by T. ferrooxidans involves the formation of an activated complex. whose thermodynamic values have been calculated to be ?G? = 92.1 kJ, ?S? -148.8 J K-1 and ?H$ = 47.8 kJ. The maximum volumetric oxygen mass transfer coefficient for the reactor leaching was found to be achieved by using an optimum air flow rate of 1970 cm min l at a rotational frequency of 1000 min-1. The highest copper extraction in tank (reactor) leaching experiment was 86.8% after 17 days of leaching, while in the sterile runs the corresponding copper extraction was only 40.1%. The copper extraction was suggested to be diffusion controlled. The power requirement of the aerated reactor was calculated to be Pg = 2.02 watts. During leaching, the oxygen saturation concentration was found to be C* = 6.70 mg dm-3. Using the gassing out method the critical oxygen concentration was assessed to be CCrit 0.05 mg dm 3. From the Warburg experiments, the kinetic parameters of the Monad equation were derived with a new evaluation technique to be Vmsp = 9.0 µm3 02 min-1 mg protein-1 and K = 7.4% pulp density for the effect of substrate concentration. The order of reaction and the overall reaction rate constant were determined from the modified van't Hoff plot to be n = 0.0 and k = 1.49 p dm3 02 min-1 mg Protein -1 for the chalcopyrite concentrate oxidation by T. ferrooxidans. On the basis of this experimental work, a preliminary flow sheet has been proposed for the bioextraction of copper from flotation concentrates.]

Jan 1, 1985

By F. Nava-Alonso, O. Alonso-González, A. Uribe-Salas, R. Pérez-Garibay

"Cyanidation is the most used method to recover gold and silver from their ores. In this process, other metals besides gold and silver may sometimes dissolve and interfere with the efficiency of extraction. Copper is one of those metals, reaching concentrations as high as 1000 mg/L in some cyanidation plants, making difficult the extraction and purification processes, and increasing the operating costs.This preliminary work was intended to study the feasibility of using amines to form a precipitate and to eliminate copper from a synthetic solution containing high copper and cyanide concentrations, as is the case of some cyanidation effluents. The solid formed is removed from the solution using conventional filtration techniques. Seven amines were evaluated at different pH values and amine additions. Up to 90% of copper present may be removed at the natural pH of the effluent (alkaline). The remaining copper would permit to recycle the solution back to the cyanidation process. IntroductionCopper is generally considered the most problematic metal in gold leaching due to the rapid formation of copper cyanide complexes when some readily-soluble minerals are processed (e.g., azurite, malaquite, cuprite, chalcocite and bornite). The copper solubilization as cuprous cyanide complexes leads to a significant economic penalty in terms of excessive cyanide consumption and high cost for cyanide elimination. When activated carbon is used to recover gold and silver, the copper-cyanide complexes decrease the efficiency of the process because of the competition of the cuprocyanides with the aurocyanide for the adsorptive sites on the activated carbon (Rees and Deventer, 1999).Several techniques have been developed to attempt to overcome the problems caused by the copper presence in cyanidation solutions, notably: acidification-volatilization-regeneration (AVR), ion exchange-electrolysis or solvent extraction-electrowinning (Lu et al., 2002). In this work the use of some amines is proposed to remove the copper-cyanide complexes by precipitation of a copper-cyanide-amine solid. The process was evaluated for different amine additions and pH values, using copper-cyanide synthetic solutions of composition similar to that presented by some cyanidation plants with high copper."

Jan 1, 2008

By J. A. S. Tenorio, A. B. Botelho Junior, I. A. Anes, D. C. R. Espinosa, M. A. Caralho

Recovery of metals from reserves with low grade and from waste with high presence of contamination is a challenge to be overcome. Metals like nickel, cobalt and copper could be recovery from nickel laterite leach waste by many different processes. Among recovery processes that could be applied are ion exchange, solvent extraction and precipitation. The aim of this work was recover copper from liquor of nickel laterite by precipitation using chemical reduction. Copper concentration in liquor was 146 mg L −1 and reducing agent used was sodium dithionite 1 mol L −1. Influence of stirring speed was studied between 0–200 rpm. Results indicated a selective precipitation of copper on solution with others metals at 240 mV. The analyzes were conducted in SEM, energy-dispersive X-ray spectroscopy and XRD, that indicated presence of copper and sulfur.

Mar 1, 2018

By Levent Özmen

Colemanite is a mineral containing varying amount of boron that is found in abundance in Turkey. It has a good possibility to be used as a flux in iron and steel industry. In this study a review of the use of colemanite, as a flux agent in steel production has been carried out and various related aspects such as its influence in metal-slag reactions, solubility of lime and magnesia in the slag are discussed along its performance in several points of views including its technical and environmental usage characteristics. Positive and negative factors of using this material as a flux are also underlined.

Jan 1, 2006

By Leszek Blacha

Since several years aog there is noted an increasing importance of the metallurgical vacuum technologies. This refers mainly to the extra furnace steel treatment processes, melting of steel and special alloys in the induction and arc vacuum furnaces, as well as refining processes of nonferrous metals. In the presented work, there is discussed a phenomenon of evaporation of volatile components of metal bath under reduced pressure with description of kinetics of this process. In this article are presented are the evaluation of the mass transfer coefficients in the melt and gaseous phase. Based on results of our own research on removal rate of impurities from liquid copper (bismuth, lead) in vacuum refining process, it is determined the thickness of hypothetical boundary layer in the gas phase. This allowed to formulate a general kinetic equation defining the evaporation rate of gaseous components from metal bath. The values of mass transfer coefficients determined from this equation were compared with experimental results by other authors working on the evaporation effect of melt components of metal alloys.

Jan 1, 2006

By Ann M. Hagni

The mineralogical, chemical, microtextural, and particle size character of electric arc furnace (EAF) dusts are being studied by reflected light microscopy, scanning electron microscope-energy dispersive spectroscopic analysis (SEM-EDS) and electron probe microanalysis (EPMA). The dusts consist predominantly of metallic iron, iron oxide, and calcium-iron-manganese silicate phases, together with smaller amounts of iron-manganese-zinc-calcium, iron-calcium-zinc-manganese, and calcium-iron-manganese silicates. The samples vary in their zinc contents. Chlorine occurs in phases containing iron, lead, zinc, manganese, and calcium. The dust particles range greatly in size from 1 to more than 300 ~m, but most particles are about 1 to 6 ~m. Larger particles. about 20-50 um across. also are present. They are predominantly spherical in shape, but some are cenospheres, and others are more angular particles, some of which are broken spheres and cenospheres. Their internal microtextures exhibit evidence of liquid immiscibility, exsolution, skeletal crystal growth, and oxidation react i on rims. Because EAF dusts have been classified by EPA as hazardous wastes, there is heightened interest in the treatment of these dusts to render them non-hazardous. The mineralogy of products of pyrometallurgical treatment of EAF dusts by flash furnace and pyrohydrolysis are currently under study.

Jan 1, 1991

By Matthew Tunnicliffe, Akram Alfantazi, Paul Nesbitt, Farzad Mohammadi

"Lead and its alloys are proper candidates for anodes in electrowinning processes mainly because they are insoluble in the leach solutions and relatively cheap. However, the annual cost of corrosion problems associated with these anodes is millions of dollars. In this study lead-silver and lead-calcium anodes were tested under typical nickel electrowinning conditions and the effect of chloride on the corrosion performance of the anode materials was investigated. Corrosion rates of the anodes were calculated using the discharge plateau (reduction of lead dioxide to lead sulfate) after galvanostatic experiments. It was found that lead calcium anodes have the highest corrosion rate both in the presence and absence of chloride. Surface morphology of the electrodes was studied using SEM and the corrosion products were characterized using XRD.IntroductionLead (Pb) is usually the preferred material for commercial anodes since it is insoluble in the leach solution and the costs are manageable. One advantage of using an insoluble material as an anode is the higher purity of the cathodic deposits and better quality of the end product. During nickel electrowinning, metallic nickel is deposited on the cathode while oxygen evolution reaction (OER) takes place on the anode. In practice, relatively high potentials are necessary for the reaction to proceed at the desired rate because of the high overpotential of OER on lead. Lead anodes get oxidized in typical electrowinning conditions and usually have two to three years of lifetime. Although the price of each anode is insignificant, the overall cost of corrosion of these anodes is considerable, which is due to the large number of anodes used in a plant, typically two to three thousand. Therefore, corrosion is a significant problem associated with lead anodes in commercial nickel electrowinning plants and industries show interest in addressing this problem. Corrosion of lead electrodes in acidic environments has been previously the subject of many research studies [I-7]. It has been reported that, during the anodic polarization of lead, several phases may be present on the surface, depending on the potential range that is being studied [8]. Lander showed that lead is oxidized at potentials higher than 0.252 YsHE with tetragonal lead monoxide being the main reaction product [9]. At 0.666 YsHE lead can transform to lead dioxide; however, it is not stable and transforms to lead sulfate and lead oxide. At potentials higher than 1.684 YsHE, lead dioxide is eventually a stable phase and forms a protective layer on the surface [I 0, 11]. Under conditions of a typical nickel electrowinning plant, usually a 200 A/m2 current density is passed through the electrodes."

Jan 1, 2012

By Christophe Thiébaut

Keywords: Pyrochemistry, Salts Treatment, Distillation The pyrochemical purification of metal generates spent salts. When this metal is an actinide such as plutonium, the slags cannot be discarded and are thus disposed in nuclear facility. In order to handle with these slags, the decision has been taken to reduce stored quantities. The development of a pyrochemical treatment is in progress in the CEA Valduc centre. The feed salt, typically composed of various Pu and Am species contained into monovalent or divalent chloride matrix, is first oxidized to convert the actinides into oxides. Then the chlorides are separated from the actinide oxides by vacuum distillation. Temperatures higher than 750°C for monochloride salts mixture NaCl/KCl and higher than 1100°C for divalent CaCl2 base salts, are required to produce an industrial flow of vaporization. Inactive qualification of the process for NaCl/KCl base salt has been carried out with lanthanide surrogates. Then, a pilot equipment, called distillator has been designed and built for production-scale distillation of NaCl/KCl and CaCl2 oxidized plutonium salts. Industrial flows of vaporization have been obtained with this pilot equipment : about 4 g/cm²/h for NaCl/KCl at 800?900°C and 1 Pa, and more than 1,5 g/cm²/h for CaCl2 base salts between 1000?1200°C at 0.1 Pa. The last step, now in progress, is the integration of the distillator into a glove box.

Jan 1, 2005

By Annette Revet

Aluminum fluxes have been used for the remelting of secondary aluminum since the beginning of the recycling industry. During the last sixty years, a number of fluxes have been designed, researched and tested at the laboratory and plant scale. Fluxes are primarily a mixture of potassium chloride and sodium chloride with the addition of some other chloride and fluoride containing salts. The conventional Mining methods of potassium chloride and sodium chloride yield products that are not high in purity without costly reprocessing or additional refining. In 1993, Kalium Chemicals, Ltd. began supplying flux mixtures to the aluminum industry. Kalium produces potassium chloride and sodium chloride which are mined and refined by a patented solution-mining process. The salts produced by this process are high in purity with lower concentrations of iron oxide, sulfates, and other impurities. This paper will present the different mining methods used in the production of sodium chloride and potassium chloride. The paper Will address how these mining methods affect the purity of the final product as well as the effect of purity on the performance of the fluxing salt.

Jan 1, 1995