Search Documents

By Linfeng Zhou, Rong Sun, Guanghui Li, Zhiwei Peng, Tao Jiang

Dust, or airborne particulate matter, from metal smelting can be either mechanically or thermally generated and it negatively affects the indoor air quality as well as the fugitive emissions from the plant. The thermally generated dust is often referred to as fume and it is typically generated whenever liquid metal comes into contact with air. For practical reasons, such as vehicle access, etc. it is often difficult to collect 100% of the fume. It is therefore highly desirable to develop processes and optimize operational procedures so that fuming can be kept to a minimum. In this series of experiments, the mechanism of active oxidation and fume formation from liquid silicomanganese under an impinging air jet in the temperature range 1400-1600°C has been explored. Characteristic properties of the fume have been established; particle diameter, shape, size distribution, and elemental composition are reported. The oxidation process is described in terms of vaporization, oxidation and agglomeration. In the boundary layer, two competing mechanisms seem to be operative in parallel: a direct oxidation of Mn vapor, and a two-step oxidation of silicon. The thermodynamic and kinetic conditions governing the two mechanisms are discussed.

Jan 1, 2016

By M. P. Bohrer

A closed-loop hydrometallurgical process has been developed for treatment of smelter flue dust generated by copper recycling. The process is a semi-continuous operation in which zinc, iron, and copper are first extracted from the dust with a sulfuric acid solution. The lead and precious metals, initially present in the dust, remain as solids and can be recycled to the copper smelting furnace. Cementation with iron and zinc metal purifies the zinc and iron-rich liquid stream prior to spray drying. The spray-dried product, consisting of a mixture of zinc sulfate monohydrate and iron sulfate monohydrate, is a desirable micronutrient additive for use in animal feeds. Treatment of the smelter flue dust in this manner will generate a positive return on investment, as well as mitigate a potential environmental liability.

Jan 1, 1992

By A. Lackner

Using the CFD software package FIRE, the smelting process inside a cyclone reactor is modelled. The fluid flow is calculated 3 dim., using different turbulence models. The effects of design parameters (length and diameter of the cyclone, concentrate feeding tangentially or from the top,..) and operating conditions are investigated. Single particle traces illustrate how to increase particle retention time before the particles reach the liquid film flowing down the cyclone wall. Moreover a two phase flow approach is developed, based on the "Discrete Droplet Model". The position, velocity, diameter and temperature of each reacting particle is described. The results show the advantages of top concentrate feeding, large height/width ratio of the tuyeres and increasing number of tangentially gas inlets.

Jan 1, 1995

By Elders. Wilfred A.

Petrological and geochemical methods, the utility of which has long been established in the mining industry, are proving useful and cost-effective in elucidating the thermal evolution of active geothermal fields. In return, they yield insights into sulfide-silicate equilibria, mass and energy transfer in convecting hydrothermal systems, and the genesis of hydrothermal ore bodies. Within the Plio-Pleistocene sediments of the delta of the Colorado River, in the Salton Trough, several active geothermal systems are known. Temperatures vary from 100-365°C, at less than 2 km depth, and salinities vary from 3,000 to 280,000 ppm, total dissolved solids. The hydrothermal alteration causes marked induration of the sediments, producing greenschist facies metamorphic minerals, including hydrothermal ore minerals. Subsurface authigenic minerals show strong correlation with increasing temperature. A typical sequence in sandstones is (below 150°=C) montmoril-lonite-kaolinite, (above 180°C) chlorite + illite, (above 225°C) calc-alumino-silicates, (above 325°C) biotite. There is a transition from porosity-dominated\to fracture-dominated permeability in the hottest and deepest geothermal reservoirs. This regular series of minerals provides a practical tool during exploration drilling. From drill cuttings, we can make predictions on reservoir temperatures, useful in making decisions on well completion. Other types of geothermometry we have employed include light stable isotopes, fluid inclusions and vitrinite reflectance measurements. A combination of these techniques not only improves our temperature predictions, but together with fission tack annealing studies, permits us to model the dynamics of temperature change and fluid flow in these geothermal reservoirs.

Jan 1, 1981

By H. Y. Sohn

The considerable progress made in the sulfide smelting technology since the first International Sulfide Symposium of 1983 is discussed. The new developments and innovations have largely been driven by the recognition of environmental concern as well as the need for increased productivity. The smelting technologies for various nonferrous metals are reviewed, with an emphasis on the industry trend towards larger plants and continuous processes. The tremendous advances made in process modeling and computer simulation to describe the complex smelting processes are also reviewed. The goal of these mathematical models is the quantitative description of the processes and the reactors that will provide a means for the control and optimization of smelting operations as well as the optimal design of the operating conditions and the reactors. Environmental issues remain a key consideration in the smelting industry. One of the most remarkable improvements made in the last fifteen years since the 1983 Sulfide Smelting Symposium is the rapid increase in the sulfur capture by nonferrous smelters. This and other related issues are briefly discussed. Finally, the challenges that the smelting industry faces as the new millenium approaches are discussed. The industry continues to face technical challenges to improve productivity and efficiency, while being responsive to ever-increasing public pressure for environmental protection. It also faces external challenges from factors that may cause the reduction of metal uses as a result of substitutions by other materials. Another serious challenge and dire consequence that the primary metals industry is expected to face is the serious diminution of university-educated manpower as well as basic-research output. To remain competitive and healthy, the industry should take up the void left by the complete disappearance, at least in the U.S., and the reduction in other nations, of the governmental support of higher education and basic research in the field of primary metals production.

Jan 1, 1998

By K. Mansfield

Spent Pot Lining (SPL) is an unavoidable waste product of the electrolytic process in the smelting of aluminium. SPL is considered to be a hazardous waste in various countries because it contains significant quantities of absorbed fluorides along with traces of cyanide. In 1995, Portland Aluminium undertook the investment of AUD$26,400,000 to construct a Research and Development processing facility at Portland, Victoria, Australia, to treat SPL. Extensive research, development and design were carried out over 5 years prior to the investment decision. This study led Portland Aluminium to install an Ausmelt pyrometallurgical furnace to combust and melt the SPL producing a hydrogen fluoride (HF) laden gas, which was cooled and then converted to aluminium fluoride (AlF3). Both the cooling and AIF3 manufacture were processes developed by Portland Aluminium. Many commissioning, equipment reliability and process problems have been encountered that had not been experienced in the trials at Ausmelt or in the developmental process for the treatment of the furnace offgases to form AlF3. Designs based on anticipated process expectations have had to be re-engineered by the SPL team to ensure plant and operational success. In June 2001, the installation of the final major component - a slag granulation process - was completed. This has produced a vitrified (glassy) slag that is expected to have leachability qualities acceptable to the Victorian Environment Protection Authority (EPA) to allow commercial end uses of the slag material to be developed. Today (September 2001), the smelter has successfully used the fluoride product, namely 65- 70% AIF3, in aluminium production and the SPL plant has significantly increased throughput with expectations to be at annual design rates of 12,000 tonne of SPL in early 2002. "The Alcoa Portland SPL Process" has been technically developed and is a proven process for the treatment and recovery of valuable components from SPL materials.

Jan 1, 2002

By Harrison Cooper, Stephen Pack

"Data from samples taken during rotary air blast and reverse circulation drilling are crucial to properly assessing economics of mineral deposits in the case of exploratory work, and are equally critical in accurately delineating ore and waste in execution of mine operation plans. Past studies of sampling procedures, comparing results of conventional splitting to more precise extraction of representative samples, illustrate the significant degree of error frequently encountered. Economic impact of error in mine blast hole sampling work can be shown to result in theoretical losses valued at millions of dollars annually in operating large scale mining projects. Results of past drill sampling studies are reviewed.Drill sampling technique can be improved by collecting coarse and fine particles together and extracting samples for assay from the complete flow of rock and dust simultaneously. This can be accomplished with a collection unit attached to the drill stem through which all except a small proportion of extreme fines are retained. The bulk mass can be static sampled as flow takes place through the collector when size reduction is not required. Alternately, collected mass with fines and coarse intermingled can be processed for increased accuracy through size reduction to obtain proportional samples."

Jan 1, 1999

By W. Drummond

The cooling of smelter gases by air dilution, adiabatic evaporative cooling and indirect heat exchange is discussed with reference to the ,process, to the subsequent cleaning of the gas and to the use of the heat extracted from the gas. The method of reducing the effect of acidic ,sulphide formation on the corrosive properties of the gas and the dust and the development of surface cleaning mechanisms are discussed. The development of indirect recuperators using air, water or steam cooling, made 'possible by the control of surface fouling is traced. The application of the modern Waste Heat Boiler to the new sulphide smelting processes is discussed with respect to the natural and forced circulation concepts. Case histories are presented to illustrate mistakes made with respect to designs produced without recourse to sensitivity analysis and without an appreciation of "worst process conditions".

Jan 1, 1992

By E. N. Mounsey

The paper addresses the design of the Zhong Tiao Shan Company (ZTS) Houma Ausmelt Technology copper smelter in People's Republic of China. The smelter represents the third copper smelter development using Ausmelt Technology, the first large scale (35,000 tpy blister copper) and the first smelter to use the Ausmelt Technology smelting and converting process steps in separate TSL vessels in a continuously operated process. The project will be realised through the combined efforts of ZTS, Ausmelt and ENFI, the Beijing Non-Ferrous Engineering Institute who provided partial detail engineering services in China. Ausmelt will provide the technology licence, basic and detailed furnace engineering packages and additional technical services including cold commissioning support and hot commissioning supervision.

Jan 1, 1999

By Saeid Pournaderi, Ahmet Geveci, Ender Keskinkilic, Yavuz A. Topkaya

There are mainly three commercial nickel laterites in Turkey: Gordes, Caldag and Sivrihisar. The first two appear in Western Anatolia. The third one, Sivrihisar (Yunusemre) laterites have been found in the first decade of the millennium, in the Central Anatolia region of Turkey. Since then, mining facilities have been continued in Yunusemre. Calcination, prereduction and smelting of Sivrihisar laterites have been extensively studied and published. In the current work, some results of the studies related to characterization of Sivrihisar laterites will be presented.

Jan 1, 2016

By Xuewei Lv, Yuelin Qin, Guibao Qiu, Chenguang Bai

"Blast furnace slag (BF slag), is the main by-product in the ironmaking process, which contains large amounts of sensible heat. To recover the sensible heat, this paper described the hot experiments which were carried out in a rotary multi-nozzles cup atomizer, where the molten BFS was transformed into granules without water impingement; subsequently, a new method-pyrolysis the printed circuited board (PCB) with the hot BFS particle, was proposed for recovering the sensible heat in this study. The gaseous products were analyzed by gas analyzer. The residual of the PCB was analyzed by FT-IR and XRD respectively, and the obtained slag particles were analyzed by XRD.The results showed that it is a feasible process of pyrolyzing PCB powder with the hot BFS particle. The sensible heat of hot BF slag could be converted to chemical heat and a large amount of combustible gas could also be generated during the process.IntroductionDue to the rising of the product cost of blast furnace iron (BFI) and the increasing public awareness of environmental problems, the steel industries have to focus on the energy saving and emission reduction. Blast furnace slag (BF slag) is a byproduct from blast furnace exhaust temperature of 1450°C or so, is a high-quality waste heat resources. In China, the steel industry produces approximately 220Mt ofBFS per year, and the enthalpy of those slags is approximately equivalent to 13.3% of the whole energy consumption in the ironmaking process[!]. It can be seen, recycling waste heat is an important way of energy saving for iron and steel enterprises. The molten slag was treated by conventional water quenching method without any recovery of heat in spite of its huge potential. Also, the water quenching process consumes a plenty of water, pollutes the air and water[2]. Additionally, the extra energy is necessary for the drying process of slag to produce cement. As a kind of secondhand resource which can be reused, the BF slag contains a large amount of sensible heat. To recover the sensible heat of BF slag, three key problems should be considered, which refer to ( 1) the dry granulation of BFS without consuming water, (2) how to recover the heat of slag particles efficiently, (3) how to use the slag particles after heat recovery."

Jan 1, 2012

By J. V. Atwood

The U.S. Bureau of Mines has developed a novel Double Membrane Electrolytic Cell (DMEC) that exhibits unique features for recycling contaminated metals and metal alloys. The DMEC incorporates two anionic ion exchange membranes, separating anodic and cathodic regions of the cell. The ion exchange membranes prevent significant transport of unwanted cationic impurities to the catholyte from the impure anolyte while the anion/cation balance in cell compartments is maintained through the free movement of anions between compartments. The membrane barrier makes it possible to electro refine highly contaminated materials or to electrowin from solution while utilizing alternate anode reactions. Sinceanolyte and catholyte cross contamination has been eliminated, premium cathode products are produced. The DMEC has been tested at bench, pilot, and commercial scales. Configuration of the DMEC, cell operation, scale, up efforts, and significant design factors are discussed. Two separate recycling investigations utilizing DMEC technology are presented. The first investigation examines recovery of high purity cobalt and nickel from severely contaminated super aIloy scrap. The second involves? upgrading contaminated cobalt in the U.S. Government's National Defense Stockpile. Capital and operating costs for both potential applications are presented.

Jan 1, 1995

By S. M. I Kytö, J .. K. Mäkinen, K. Saarhelo

"At the Outokumpu Oy Harjavalta Copper Smelter the control philosophy of the flash smelting process has been changed from the slow feed-back control to feed-forward control. This is important as the fluctuations in the flash smelting furnace matte grade and slag temperature are desired to be minimized.The system is based on a specially designed automatic sampling device and the Outokumpu Courier 20 on-stream X-ray fluorescence analyzer. A microcomputer-based Analyzer Operator Station (AOP) controls the system and calculates the process parameters for the furnace from the analyzed chemical composition and other existing data.A considerable reduction in the deviation of the matte grade and slag temperature has been gained. This has resulted in conservation of energy and refractories, lower copper losses and higher through-put in the flash smelting furnace and converters.1.0 IntroductionThe flash smelting technology for copper concentrates was developed at the Outokumpu Oy Harjavalta Smelter soon after the World War II. The incentive for this development was shortness and high price of any form of energy. The fact that smelting can be carried out autogenously, without external energy by utilizing the latent heat of sulfide combustion was known decades before, but Outokumpu Oy was the first company to take the advantage of this knowledge in practical operation. A further advantage of this technology was that the SO2 containing gases suited well for sulfuric acid production, thus minimizing the detrimental effects on the environment (1).The very heart of the flash smelting process is the reaction shaft of the flash smelting furnace (see Appendix I). Heating up of the dried feed mixture, dissociation of several compounds, ignition and oxidation of the feed take place very intensively in the reaction shaft during 2 - 3 seconds, which the fine grained particles reside in the reaction shaft. A very accurate control of the amounts of the feed materials as well as of oxidizing gases, fuel, etc. is of primary importance."

Jan 1, 1989

By A. P. I. Popoola, D. O. Okanigbe, A. A. Adeleke

In view of the steady depletion of primary sources of copper and the increased global demand for refined copper, it becomes necessary to explore some secondary sources for possible extraction of copper. The waste copper smelter dust (CSD) is a rich secondary resource for copper as shown by the chemical composition of the South African Palabora coppers smelter plant CSD that assayed 18.02, 13.36, and 3.4 wt% copper, iron and sulphur, respectively. Studies on CSD have focused majorly on either dust characterization or treatment, while hydrometallurgical extraction without pretreatment and with pretreatment using techniques such as oxidative roasting are also considered quite attractive. The challenge of iron dissolution during the leaching stage in these processes necessitates adequate purification of the leach liquor before the extraction of the metal as nano-particles. Hence, this review examined the theories relating to the characterization and treatment of CSD for copper recovery as nanoparticles; with factors having a bearing on the treatment process such as kinetics considered with the aim of providing scientific basis for the research.

Mar 1, 2017

By Ross W. Smith

Microorganisms are increasingly finding use in mineral processing and hydrometallurgy both for the enhancement of mineral engineering operations and for the remediation of mineral industry wastes. Some of the applications, such as biologically assisted leaching of sulfide ores and biooxidation of refractory sulfide gold ores, are established commercial processes. Others, such as the use of organisms for the removal of heavy metal ions from dilute aqueous streams, are nearing commercial application. Other uses of microorganisms are potentially possible. These include use of microorganisms in leaching non-sulfide ores, the flocculation or flotation of minerals and remediation of toxic chemicals discharged from mineral engineering operations.

Jan 1, 1993

By Larry M. Southwick

Considerable process and equipment development and analysis were conducted during design of Freeport Sulfur's laterite nickel facilities in the late 1950's. These covered ore concentration at Moa Bay, Cuba, and concentrate refining at Port Nickel, Louisiana. Both facilities utilized acid pressure leaching and product refining steps that were similar to those later used elsewhere in the laterite processing industry. Unfortunately, developments in Cuba removed the Moa Bay facilities from Freeport control. This deprived the project of a start-up that would have allowed thorough resolution of difficulties and a quicker attainment of production capacity. This meant lost opportunity to positively prove and complete the technology when optimum resources and staff were available. This paper reviews the original rationale of how design was developed via laboratory, bench scale and pilot studies by Freeport Sulfur. Some later operating problems will also be discussed. This case is unusual, but the lessons learned may be instructive in the application of difficult and complicated technologies, as well as the need to understand and retain access to the original development and design activities Keywords: Moa Bay, Freeport Sulfur, Port Nickel, acid pressure leaching, pilot plant, pachuca, Chemical Construction, pressure letdown, cobalt, titanium

Jan 1, 2004

By J. D. McCain

Magma's San Manuel smelter has adopted new operating techniques resulting in 21% increased productivity and 87% reduction in lost time accidents. Reverberatory furnaces were converted to coal firing from expensive natural gas and fuel oil. Slag and matte flow problems and safety were improved by implementing hydraulic slag stopping and matte tapping machines. Coordination of furnaces, converters and acid plant was improved by using a computer-aided converter controller/scheduler function. Manual mudding of converter lips after each collar pull was replaced with a gunning system for coating the mouth castings. One converter punch car was automated using robotic technology. An automatic anode take-off was installed with fewer moving parts and a mechanism for ear twisting one cell contact. Anode copper refining was improved by replacing propane/hydrogen mixtures with high pressure/velocity natural gas tuyeres. Improved converter scheduling increased acid plant production 43% with more autothermal operation time. Six dedicated computers/microprocessors are utilized for automation, data acquisition, process monitoring and on-line air quality information for the Supplementary Control System.

Jan 1, 1983

By K. Morsi

Titanium-titanium boride whisker (TiBw) composites are emerging as strong candidate materials for advanced applications within the automotive, aerospace and defense industries. Although increasing TiBw volume fraction improves the specific stiffness and wear resistance of titanium, it is usually on the expense of fracture toughness and ductility especially at increased volume fractions of reinforcements where whiskers interlock. This research addresses strategies for microstructural design that may overcome these shortcomings, by generating titanium composites that are locally reinforced with TiBw through in-situ reaction in segregated regions of the microstructure and separated by ductile Ti matrix. The effect of varying composite reinforcement particle sizes (i.e. size of the reinforced regions) on the pressure-less sintering of these dual matrix composites is discussed. Electric current activation was also used to generate high density dual matrix composites and a new simultaneous imaging and modulus mapping technique was used to characterize these unique microstructures.

Jan 1, 2008

By R. Angulo

Carbon nanotubes (CNTs) have recently emerged as materials with outstanding properties. This has promoted their consideration as reinforcements for other material systems, such as ceramics. However, one of the fundamental problems with producing CNT-reinforced ceramics is the effective dispersion of CNTs during processing. This has been successfully carried out recently using organic solvents. This paper is a preliminery investigation into the rheological behavior of aqueous CNT-alumina slips, with the objective of moving towards a more environmentally friendly aqueous tape casting process for the production of CNT-ceramic composites.

Jan 1, 2008

By Milorad Cirkovic

Kinetics of copper concentrate oxidation in roasting processes in a fluidized bed reactor has been studied at temperatures between 600°C and 720°C using particles of 0.038 to 2.5 mm in average size. The analysis of composition of samples has been done by chemical methods. Phase composition has been determined by Siemens X-ray equipment with Cu anticathode and Ni filters at a voltage of 40 kV and a current of 18 mA. The content of sulphur has decreased from 33.23 to 19.02 mass percent with the increase of temperature, but the content of Fe304 has increased from 0.15 to 17.14 mass percent. The new mechanism of copper concentrate oxidation in a fluidized bed reactor is proposed in this study. It has been shown from the mathematical model that the velocity of oxidation of copper concentrate between 600°C and 720°C is virtually controlled by the rate of diffusion of 02 through the layer of reaction product.

Jan 1, 1999