Search Documents

By Jiang Feng, Zhang Libo, Peng Jinhui, Guo Zhanyong, Ju Shaohua, Lei Ting

The clean utilization of the residue containing chloride, CuCl residue, produced from zinc hydrometallurgy is very important for the recycle of valuable metals. And drying is the main process in recycling. In this study, response surface methodology was used to optimize operating conditions of the drying of CuCl residue in a convection oven and desirability function used as the methodology for the optimization. Optimization factors were air temperature (80–100°C), material thickness (10–25mm) and process time (80–120min) while investigated responses was final moisture content. The optimum conditions were found to be the temperature of 95.48°C with the material thickness of 13.47mm for the process time of 89.48 min. Under optimum conditions, the predicted moisture content of CuCl residue was 4.11% while the experimental date was 4.13%. The experimental value after process optimization was found to agree satisfactory with the predicted value. After drying, XRD was used to analyze the main phases of CuCl residue. The CuCl residue is made up of CuCl,Cu2O, ZnS and other compounds.

Jan 1, 2015

By Kazue Moriya

At the 1980 TMS-AIME world symposium, Dr. Davey mentioned that the traditional lead blast furnace is now being challenged by direct smelting processes. In the copper smelting field both the blast furnace and reverberatory furnace are also disappearing in favour of direct smelting processes such as Outokumpu flash smelting, Mitsubishi continuous smelting, Noranda furnace, Inco furnace and so on. Those new processes all have the following in common: (1) High degree of mechanization (2) Metallurgical reactions carried out in closed vessels (3) Application of oxygen and/or oxygen enriched air (4) Minimization of handling materials and gaseous volume (5) Minimum energy requirements (6) Removal of workers from near the furnace (7) Reduction of emissions of harmful gas to meet environmental regulations. (8) Improvement to the work place environment to avoid occupational hygiene hazards. Direct and continuous smelting of powdered concentrate in one vessel was a romance of the metallurgist since early times. However as mentioned above, in the copper field this objective is being achieved in practice. The industry however can't deny that the serious and severe regulation of environmental pollution in every country was the prime motive for the modernization of smelters. In early days, to meet regulations, it was anticipated that many economic difficulties such as higher capital and energy costs and extravagant use of resources and waste disposal would be the result. "Turn a misfortune into a blessing" is an old saying which reveals the current thinking and reacent developments in the nonferrous industries. In the last ten years in the lead smelting field, about two decades later than copper, commercial scale smelting using new furnance technology has started. The KIVCET process and QSL process, which is flash smelting and bath smelting respectively, are becoming major competitors. They will be sure to upgrade their processes to remain economically and environmentally viable in the comming decade.

Jan 1, 1990

By G. Mark Aylmore

Various processes have been developed using a combination of elevated temperature and chemical treatment processing to recover Li from silicate minerals. To facilitate further process development, a comprehensive understanding of the deportment of Li and associated minerals in ore bodies is essential to allow the industry to predict the response of ore reserves to metallurgical treatment options. This paper describes results from the integrated use of the John de Laeter Centre’s state of the art analytical and mass spectrometry techniques to characterise a selection of Li bearing ore bodies and determine their amenability to potential processing options for the extraction of Li. The mineralogy, mineral associations, and liberation characteristics of ore-bearing and gangue minerals were characterised using a combination of the TIMA and XRPD studies. The Li content and distribution within minerals were defined using LA-ICPMS and field emission scanning electron microscopy techniques (EBSD, ToF-SIMS) and atomic probe microscopy.

By Roberto Parra

The classic criteria of the preparation of the charge for the smelting of copper concentrates in a flash furnace considers the mass and energy balance from the chemical and mineralogy composition of the concentrates. The operation parameters fixed with this method don't assure the stability of the operation and the critical problems of the slag quality and dust formation occurs very often. This paper presents the results of a laboratory test that allows the predicition of the behavior of concentrates blends in the view of the minimization of the dust formation and the magnetite control in the slag. The combustion of different copper concentrates and blends were done in a drop tube furnace. The results show that the magnetite and dust formation don't have a linear behavior with the weight proportion of the blend and some optimal blends of 2 or 3 types of concentrates can be identified. From the reasonable hypothesis that the qualitative behavior of blends in the drop tube represents the real behavior in the burner, the preparation of the charge with this approach could help to solve those operational problems.

Jan 1, 2003

By Mukesh Jain

The liquor from potroom wet scrubbers is treated with lime to precipitate the soluble fluorides. The solids after filtration, referred to as scrubber mud, contain in addition to calcium fluoride, alumina, carbon, tars including polyaromatic hydrocarbons (PAH), cryolite and pachnolite and are considered hazardous. This communication deals with the pilot plant scale calcination of scrubber mud with a rotary kiln to obtain non-hazardous fluoride raw materials. Air classification was performed to separate the mudinto aluminarich andcalcium fluoride rich fractions which were then calcined. With proper control of calcination parameters and addition of lime, the carbon and tars were destroyed and hydrogen fluoride emissions were controlled. The calcined products could be used in the steel indusny as a fluxing agent or as a substitute for fluorspar in the production of aluminum fluoride.

Jan 1, 1994

By D. G. Mason

During the design of copper refinery tankhouses, there is a need to develop mass balance calculations for many process components, so that optimum physical plant configuration is achieved. Each mass balance is complex, possibly with over 120 interactive variables as basic input data. Recent developments in tankhouse design (e.g. permanent cathodes) have greatly increased the design options available for any project, multiplying even further the requirement for calculations. In the past these calculations were tedious and susceptible to human error. A comprehensive computer program can now simplify the task of the process metallurgist, enabling more sophisticated and sensitive plant designs to be produced. The paper describes the successful development of a flexible mass balance program that originallly was used in a feasibility study which had to be completed within a short time schedule. The program has been further developed and used for design and energy calculations; it can be usefully applied to existing plants to assess the impact of variations in operating parameters. The software takes account of staged liberation, electrolyte purification bleed and generates a reliable process inventory listing: it can also cope with stripper starting sheet options and disparate commercial circuits.

Jan 1, 1987

By Bruce H. Baker

Studies of used or unused refractory materials are excellent examples of applied mineralogy in industry. Refractory materials are mineral substances containing ceramic or chemical bonding systems. Knowledge of the mineral composition, bonding, and textural relationships often explains the resulting physical property values of a refractory and contributes to the interpretation of refractory wear mechanisms occurring in steel plant service.

Jan 1, 1982

By Steven R. Pittman, Colin McCullough, Peter Galuska

"Traditionally Continuous Fiber Aluminum Matrix Composites have been fabricated using high strength fibers and high strength matrices, often commercial alloys, with the goal of producing high strength composites. However the specific role of the choice of matrix alloy on composite properties has not been well established. One way to control composite tensile strength is to use coatings to introduce a low strength interface between fiber and matrix which tends to reduce the importance of the matrix selection, but unfortunately renders the transverse strength unacceptably low. Thus using a system with strong bonding between fiber and matrix is desirable, such as an alumina fiber / aluminum alloy matrix system. In this case the transverse strength is a strong function of the matrix strength. However the longitudinal strength then depends largely on the characteristics of the matrix. The important role of the matrix is discussed using examples of alumina fibers in various aluminum alloy matrices. The key attributes are matrix constituent phases, alloy chemistry, alloy reactivity with the fiber, and matrix strength. From the understanding developed in these systems a set of design rules may be established for selecting an optimum matrix. IntroductionAluminum matrix composites (AMC's) reinforced with continuous fibers offer very attractive property gains over AI alloys, such as strength, stiffness, and fatigue resistance. These gains are magnified when specific mechanical properties are compared which make them attractive candidates for replacing steel, nickel, titanium and aluminum alloy parts in weight critical applications (1). Many systems have been tried in the past; B/AI, C/AI, SiC/AI, Si-Ti-C-O/AI and AI203/AI. Technically B/AI was a very good system but was expensive in regard to both fiber cost and fabrication and SiC/AI and C/AI systems are still plagued with reactivity problems. The Si-Ti-C-O/AI appears to be a good strength system but with lower stiffness. Until recently, the AI203/AI was a low strength system, in part due to a lack of a high strength fiber. Recently 3M introduced a high strength AI203 fiber - Nextel™ 610, which leads to high strength composites (1,2) and may also be both low cost and also compatible with less expensive casting approaches for fabrication."

Jan 1, 1996

By G. Johnston, J. Greenly, R. G. Buchheit, D. C. McIntyre, R. Muenchausen, D. J. Rej, R W. Stinnett

"Rapid thermal treatment of materials using high energy, high flux, pulsed ion beams can produce modified surface layers with unique microstrutures and properties. High energy ions loose their energy during the slowing down process in the workpiece and thus deposit their energy continuously over a depth of a few microns. The deposition of energy can lead to melting and in some causes ablation of the heated layer. Because the pulse duration of the ion beams is typically only 50-200 ns, steep thermal gradients generated during heating facilitate rapid cooling (107K/sec-108K/sec) of the treated layer by thermal diffusion into the underlying material. Rapid heating and cooling of materials can generate surface layers with non-equilibrium amorphous or nano-crystalline microstructures that exhibit increased hardness, wear resistance, and corrosion resistance. Pulsed ion beam treatment can also lead to surface smoothening or can be used to mix thin « 1 11m thick) coatings into underlying substrates. Pulsed ion beams can be generated using existing ""flashover"" ion source technology which is capable of producing single shot, mixed C, H, and O ion beams with beam cross sections of approximately 100 cm2 and energy fluxes up to 100 J/ cm2. Recent advances in repetitive high energy pulsed power technology and development of magnetically confined anode plasma ion sources have facilitated the development of ion beam systems that generate single species beams that pulse continuously at 120 shots/second. These capabilities will allow rapid treatment of large surface area workpieces at low cost.IntroductionThe rapid solidification of liquid materials can create unique materials and material microstructures that often have properties that can lead to enhanced performance. Rapid solidification processing of the surfaces of materials using continuous and pulsed laser beams (laser glazing) has been explored for over 20 years (1-5). Advances in high energy, pulsed electron and ion beam technologies over the past decade have provided rapid thermal treatment techniques that may be less expensive to impliment than laser surface treatment for many surface modification applications (6). High energy pulsed ion beams have recently been used to harden aluminum(7), copper(8) and tool steel surfaces (6,9), increase corrosion resistance of Al alloys (6), mix coatings into underlying substrates (10), and create amorphous films (11,12)."

Jan 1, 1994

By M. C. Esposito

Seven pyrite samples purified from coal sources and one ore source pyrite (for comparative purposes) have been characterized by chemical and mineralogical analyses, inherent floatability, apparent specific gravity, surface area, semiconductor type, optical anisotropy, dissolution and oxidation rate. The data clearly demonstrate that pyrites from various coal sources differ not only from ore pyrite but from each other as well.

Jan 1, 1987

By T. C. Tseng

Austenitization is a critical stage in heat treatment of steels. The available kinetic data in reference to various initial microstructures are very limited, particularly at high heating rates. In this study, integrated experimental and computational approaches have been conducted to quantify the progress of austenitization and the attained microstructure. In particular, the study is concentrated on cementite and carbide dissolution in two steel grades. Various computational methods are developed to facilitate the study: (l) an algorithm for direct determination of kinetics data as well as progress of transformation from high-rate dilatometer tests; and (2) a suite of mesoscale computational models for particle dissolution, elements diffusion, mechanics, thermodynamic and the resulting kinetics of transfonnation. Critical exprimentation is carried out using advanced techniques in microstructure characterization, chemical analysis, and Gleeble thermal-mechanical simulator on specimens of well-controlled initial microstructures. Keynotes: Cementite, Carbite, Dissolution, Steels, Austenitization

Jan 1, 2003

By D. Mishra

Electric arc furnace dust (EAFD) generated during the recycling of steel- scrap is classified as a hazardous waste for landfilling. This is because it contains leachable heavy metals such as zinc, lead,... Recovery of these metals could result in both resources conservation and resolving waste disposal problems. A study of the thermal reduction of a sample of EAFD was carried out in an inert gas atmosphere using coke as a reducing agent. Preferential volatilization of zinc and lead was achieved during the reduction process at about 800 "C. More than 96 % of both zinc and lead were removed from the dust and were recovered in the condensates. The treatment residue was essentially composed of iron oxides and almost free from heavy metals.

Jan 1, 2002

By Emmanuel N. Zevgolis

In the present work, a reduction roasting experimental study of Greek nickeliferous laterite samples with a gaseous reducing mixture ? CO:N2- is presented. The effect of parameters such as temperature, ore grain size, and composition of the reducing mixture were examined. It is deduced that the reducibility of intermediate type laterite sample, where iron appears mainly in the form of goethite (a-FeOOH), is considerably higher than that of limonitic type laterite samples, where hematite (a-Fe2O3) is the predominant iron mineral phase. The degree of reduction of the limonitic type laterite samples does not exceed 50%, while it reaches 95% in the case of the intermediate-type laterite sample under the same experimental conditions. Increasing the temperature in the range 750-900°C does not considerably favor the reduction of the limonitic type laterites, whereas decrease of ore grain size of the limonitic-type ore samples and more intense reducing conditions increase the reduction. The considerably higher specific surface area values of the intermediate laterite samples, diminishes the effect of the ore grain size and this can be regarded as the critical parameter leading to the higher reducibility of this ore.

Jan 1, 2009

By Robert R. Beebe

On the night of August 1'9-20, 1995, seepage was seen at the toe of the Omai tailings dam in Guyana. The mill was immediately shut down, and within two hours the flow, then mostly water, was diverted into an inactive mining pit nearby. At about the same time a second more serious break occurred at a point where water and solids could flow directly into the Omai River. By the time Ii coffer dam could be completed in the early morning of August 24, some 4.2 million cubic meters of tailings water and solids had escaped from the dam, of which nearly2.9 million cubic meters had reached the Omai River. This paper outlines some initial Process considerations and operational decisions which might have contributed to the dam's failure, describes how the Government of Guyana and the operator, Omai Gold Mines Limited, cooperated in dealing with immediate problems and shows how the Government set about investigating the accident. In particular, the paper details the work of a Process Review Committee comprising Guyanese and foreign experts convened to assess the gold processing and effluent management systems at Omai, and to recommend actions where appropriate.

Jan 1, 1998

By E. T. de Groot, D. L. Verhelst

With the successful start-up of Cominco's new KIVCET smelter, the final key component is now in place for Trail Operations to operate efficiently as a modern integrated zinc-lead facility. Unique metallurgical, operational, planning and management issues apply to this operation. Along with presenting the current flowsheet for Trail Operations, this paper discusses issues such as the impact of recycles, operational re-stabilization following significant process changes, plant operation with just-in-time inventories, real-time process optimization, and management philosophy.

Jan 1, 2000

By Deyou Yin, Kongfang Feng, Bo Wang, Jieyu Zhang, Xin Hong, Shaobo Zheng, Jinyin Xie

"The flow patterns and mixing characteristics in a water model of C-H2 smelting reduction furnace are experimentally studied in this paper. Water modeling is employed to investigate the features of gas jet stirring and the fluid flow patterns in the bath of a smelting reduction furnace during the top, bottom, and side combined blowing process. The influence of the gas flow rate for top, bottom and side nozzles, angle, submerged depth of each side nozzles and the height of the top nozzle has been examined. It showed that the gas flow rate of side nozzles and bottom nozzle had a key role on the fluid flow and mixing characteristics. The gas jet from the top nozzle could change the agitation and fluid flow pattern caused by the gas jets from the side nozzles in the bath.IntroductionFacing the current natural resources decrease and the environmental degradation, smelting reduction iron-making technique is believed to be the most representative at present. Mid last century, the concept of producing liquid iron or semi-steel directly from ore fines and inexpensive fuel was the subject of considerable pilot plant development activity. Among these projects, the direct smelting process, which is the reduction and melting of iron-bearing materials by carbon and other hydrocarbons in the vessel containing a molten bath, is the most popular one. A number of direct smelting processes have been developed around the world, e.g. COREX, DIOS, HIsmelt, AISI, ROMELT, etc.These studies put forward a new technology, which through bottom nozzle blowing rich hydrogen, top nozzle blowing rich oxygen and provide preheating ore and solvent, side nozzles blowing oxygen-coal to realize smelting reduction iron-making process. Owing to the metallurgy reactions always in high temperature, which is above 1600 °C, it is difficult to visualize the mixing behavior and measure the desired phenomena in the reduction vessel. With water modeling, the primary advantages are that it is relatively easy to observe and measure the flow phenomena in the bath."

Jan 1, 2011

By F. H. Froes, O. N. Senkov, N. Srisukhumbowornchai

"Mechanical alloying (MA) and thermohydrogen processing (THP) approaches were used to synthesize amorphous or nanocrystalline powders of the titanium-aluminide-based alloys and composites. Fully dense samples with nanocrystalline and bimodal structures were produced from these powders by hot isostatic pressing. The stability of the microstructures during continuous heating at high temperatures was studied. Characterization techniques including X-ray diffraction, scanning and transmission electron microscopy, energy dispersive spectroscopy, and differential thermal analysis were used in this work.IntroductionAs performance demands increase, so do the demands for enhanced mechanical property combinations at reduced overall weight; and reduced weight can most efficiently be realized by the use of low-density metals with high specific strength, such as titanium alloys and titanium-aluminum intermetallics [l]. The TiAl-based alloys are attractive for high temperature applications, however, they exhibit poor ambient temperature ductility and fracture toughness [2-4]. Incremental improvements can be obtained using ingot metallurgy processing [1,2] but more substantial developments require ""far from equilibrium"" (FFE) synthesis [5-8] which allows development of novel constitutional and microstructural effects, leading to enhanced physical and mechanical properties. Improved ductility of titanium aluminide intermetallics can be achieved by disordering, grain refinement and deoxidation of the matrix, while good elevated temperature properties are achieved due to a dispersion of fine, thermodynamically stable, second phase particles.The approaches for producing nanocrystalline and amorphous TiAl-based alloys and composites used in this work included FFE powder metallurgy techniques such as rapid solidification, mechanical alloying and thermohydrogen processing. The rapid solidification (RS) technique allows extension of solubility limits, production of novel phases, and much more refined microstructures (down to nanostructure or even amorphous range) than is possible using the ingot metallurgy technique [9]. Mechanical alloying (MA) is a process in which heavy working of powder particles results in intimate alloying by repeated deformation, fracturing and welding. This process can produce greater departure from FFE than RS, leading to greater refinement effects; and additionally allows production of a dispersion of second phase particles [10]. Thermohydrogen processing involves hydrogen as a temporary alloying element in titanium to facilitate processes, refine microstructure, and improve final mechanical properties [11]; it was used in the present work to improve MA process. The combination of these three processes was expected to control the final microstructure even better than either process used alone."

Jan 1, 1998

By P. M. Swash

This paper reviews the application of some mineralogical techniques in the evaluation of the Uitkomst Ni-Cu deposit, South Africa. The low grade of the ore necessitates detailed and representative characterisation in order to establish the prospects viability. The relevant mineralogical information is generated by using optical microscopy, magnetic and heavy liquid . separations, XRD. SEM and EMPA. Methods used are briefly reviewed. The cost savings and metallurgical understanding that is provided by the mineralogical work is described especially with regard to milling, flotation and the presence of by-products (PGMs and chromite).

Jan 1, 1991

By B. S. Terry

Experiments have been conducted to assess the feasibility of capturing bearing emissions arsenic with CaO during the roasting of enargite (Cu3AsS4). Enargite/CaO mixtures have been heat treated in air, nitrogen or oxygen for various times and the products of reaction analysed by X-ray diffraction and cleaned analysis. The results show that substantial capture of arsenic can be achieved via the formation of calcium arsenates and/or calcium arsenides. In addition significant capture of sulphur is achieved by the formation of calcium sulphate andlor sulphide. Complete conversion to copper sulphide with total removal of arsenic can be achieved within 30 minutes at 700°C. Further heat treatment in air or oxygen leads to the formation of copper oxide and copper oxysulphate. Without optimisation of reaction conditions, it has proved possible to achieve retention of in excess of 85% of the arsenic content of enargite in the form of calcium arsenates.

Jan 1, 1994

By J. H. Meza V

La Caridad operated at only 65% of design capacity during the first five years of operation. After the first major shutdown and repairs to the furnace in mid- 1992, the smelter quickly reached 95% of design capacity. Converter operation is now more efficient; blowing times have decreased from about 1.7 to 1.2 min/ton of matte. Anode copper production is now 15000 tons/month. The increased efficiency provided by better coordination and scheduling ensures La Caridad's ability to operate at present and expanded production capacity while simultaneously meeting environmental control standards.

Jan 1, 1993