Search Documents

By Animesh Jha, Catherine Davey

"Carbothermic reduction and nitridation reactions using synthetic kaolinite mineral were investigated for the formation of silicon based nitrogen ceramics. The temperature dependence of the reaction rate and its effect on phases formed are reported. The effect of the reactivity of carbon on the kinetics of formation of AIN and ShN4 is discussed. Using the standard Gibbs free energy values for the formation of nitrides and oxides of aluminium and silicon, a log po2 verses I/T diagram is constructed. The experimental data results are discussed and compared with the predicted phase equilibria. We also report the influence of sub-oxide gaseous species on the microstructure of the ceramic phases produced.IntroductionSynthetic kaolinite is a clay containing alumina, silica and water of crystallisation, and has a chemical formula 3(Al2O 3.2SiO2.2H2O). This mineral is relatively inexpensive and, is therefore an ideal candidate for use in the production of ceramic powder mixtures for example silicon nitride and aluminium nitride for composite material formation, When the mineral is heated, the water of crystallisation from the crystal lattice is lost via the 3(Al2O 3.2SiO2.2H2O) = 3(Al2O3.2SiO2) + 6H2O reaction. It has been shown [1·2j that on further heating to 1673K, the anhydrous kaolinite decomposes to a mixture of mulllte and silica, 3(Al2O3.2SiO2) = 3Al2O 3.2SiO2 + 4SiO2 which is consistent with the alumina-silica phase diagram, shown in figure 1.The binary alumina-silica phase diagram has a well-defined sub-eutectic immiscibility dome and this characteristic dernixing behaviour is reflected in the thermal decomposition of anhydrous kaolinite consequently the microstructural features resemble the spinodal decomposition process. It is well established that the spinodal decomposition process raises the nucleation frequency due to their low free energy barrier, (?G). The small magnitude of this barrier consequently promotes the evolution of a very fine microstructure. The process of spinodal decomposition is therefore expected to be influential during the reduction-nitridation of kaolinite minerals."

Jan 1, 1996

By Mizraim Uriel Flores, Elia Guadalupe Palacios, Sayra Ordoñez, Iván Alejandro Reyes, Ister Mireles, Martín Reyes, Francisco Patiño, Hernán Islas, Víctor Hugo Flores

This paper presents the characterization of a sample of mercury jarosite that was synthesized by slowly adding Hg(NO3)2H2O into a Fe2(SO4)3nH2O solution. X-ray diffraction (XRD) analysis performed on the sample confirmed that the compound presents a crystal phase corresponding to mercury jarosite. Analysis through Scanning Electron Microscopy with Energy Dispersive X-ray Spectroscopy (SEM-EDS) determined that the precipitate is composed of mercury, sulfur, iron and oxygen. It is made up of spherical particles with an average size of 38 μm; these particles are made of rhombohedral micro-crystals with sizes ranging between 1 and 2 μm. Chemical characterization was performed through dichromatometry analysis, gravimetry and atomic absorption spectroscopy (AAS), thus obtaining the following composition: 27% Fe3+, 37% SO4 2− 14% Hg2+, 22% OH− + H3O+ + H2O. The following approximate formula of the compound was determined from chemical analysis: [Hg0.39(H3O)0.22]Fe2.71(SO4)2.17(OH)4.79 (H2O)2.09.

Mar 1, 2017

By A. V. Reddy, C. Beckermann

"The DC continuous casting of a grain refined AI-4.5%Cu round ingot with realistic boundary conditions is numerically simulated. Of particular interest are the effects of the transport of free solid in the form of equiaxed grains on the macro segregation patterns and the final grain size distribution. The study uses a previously developed two-phase model that incorporates descriptions of heat transfer, solute redistribution, melt convection, and solid transport on the system scale with microscopic models of solutal undercooling, microsegregation and grain impingement. The numerical results indicate that grain transport inhibits the formation of inverse segregation in the ingot shell and promotes negative centerline segregation. This is explained by the reduction in the solid coherency next to the mold and the advection of solute-lean grains towards the centerline. Comparisons with the experiments of Finn et al. [5] illustrate the need for considerable improvements in the model. IntroductionMacrosegregation continues to be one of the concerns in DC continuous casting of aluminum ingots. The variation in composition over the ingot cross section results in the need to adjust alloy composition in order to meet mechanical property specifications in finished products. The extent of macrosegregation is greatly affected by the casting conditions, such as casting speed, superheat, cooling rate, mold size, alloy composition, and grain refining practices. Thus, it is of great interest to develop a comprehensive mathematical model to simulate the casting process, enabling the selection of conditions that minimize macrosegregation while maintaining a high productivity."

Jan 1, 1994

By Yifei Zhang, Jianzhong Li, Wenhao Zhang

Eletrochemical behavior and corrosion properties of a Ti–6Al–4V alloy fabricated by selective laser melting in artificial seawater at temperature ranges from 20 to 40 °C were investigated using electrochemical techniques, including potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), and Mott-Schottky measurement, etc. Equivalent circuits were simulated to investigate alloy surface and analytic effects of temperature on interface of alloy and solution. The results showed that corrosion potential increased with temperature rise, and the EIS presented a single capacitive resistance characteristics. When the temperature reached 35 °C or above, passive current increased, while the passivation phenomenon was not obvious and corresponding radiating arc radius reduced, indicating that the resistance decreased, conductivity of surface passivation film improved, and corrosion performance improved. According to the Mott-Schottky curves, alloys exhibited n-type semiconductor characteristics. With increasing temperature, conductivity of passivation film enhanced, and alloy corrosion resistance decreased. At 40 °C, alloy possessed the worst corrosion resistance.

Mar 1, 2018

By F. Qian

An impinging gas jet on a liquid surface is found in many industrial process systems such as electric arc furnace, welding, steel-making operation and others. Fundamental understanding of the interaction of a gas jet on a liquid pool can provide important insights into process behavior resulting in improved efficiency. A numerical model is developed for solving the flow fields of both impinging gas jet region and liquid pool below, in which the deformed interface shape is predicted simultaneously. Using curvilinear coordinates, the Navier-Stokes equations of each phase are solved separately through coupling of static pressure, shear stress and velocity at the interface. Several cases for jet distances and flowrates were investigated both numerically and experimentally with an air-water model. Favorable comparison of numerical results with experimental data confirms the validity of the present numerical approach. An existing phenomenological model for 'penetration depth' prediction was extended for smaller 3et exit height to jet diameter' ratios.

Jan 1, 1995

By Emilia Visileanu, Eftalea Carpus

"Ecological economic policy shall be understood as the sum of political, economical and environmental measurements aimed at the entire economy dematerialization and the dematerialization shall be ""imposed"" since the designing stage of goods and services"". European textile and clothing industry with a long leading tradition in terms of innovation, fashion and creativity, continues to be one of Europe's major industrial sectors. Textile industry affects the environment by high consumption of water, energy and chemicals, as well as by the large amount of waste it generates as a result of using a large number of chemicals and technological processes.Textile waste prevention, reduction and ecological exploitation require the implementation of new management and education tools.Introduction“Europe must learn from the experience of global economic and financial crisis ""- this was the conclusion of the European Commission that has elaborated a ten-year strategy designed to reinvigorate the economy and make possible a growth which is ""intelligent, sustainable and favorable to inclusion"", by a better coordination of national and European policies.Adapting infrastructure and logistics that encourage the marketing of ""sustainable"", ""fair traded"" and ""green"" products as well as other special „green” products will facilitate the movement towards dematerialization and eco-efficiency among producers."

Jan 1, 2012

By Shufeng Yang, Anping Dong, Yongfeng Chen, Jingshe Li, Lifeng Zhang, Liyuan Sun

"Instead of nickel-based stainless steel, a nitrogen-bearing stainless steel was produced to reduce the production cost stemming from the shortage of nickel recourses. Thermodynamic model to calculate the saturation nitrogen content in the stainless steel were developed and the model was validated by experimental measurement. The experiments were performed with a high temperature induction furnace. Nitrogen gas under constant pressure was injected into the crucible with a top lance by which the nitrogen was transferred to the molten stainless steel. The effects of chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were investigated and discussed.IntroductionWith the rapid production growth of stainless steels, nitrogen-bearing stainless steel has recently attracted more and more attention for their high strength and excellent corrosion resistance imparted by interstitial nitrogen without decreasing its toughness and ductility. Moreover, the addition of nitrogen to the stainless steel as a substitute for nickel leads a lower consumption of nickel, so significantly lowers the high production cost stemming from the shortage of nickel recourses. However, production of the nitrogen-bearing steel is difficult since nitrogen is a gas element and has a low solubility in the steel. So efficiently increasing the amount of nitrogen in steel continues to be one of the main concerns for the production of nitrogen-bearing steels.Currently there are some special processes to produce austenitic stainless steels with a very high N content, including pressurized electroslag remelting, counter-pressure casting, special induction melting and powder metallurgy, etc [1]. Special expensive vacuum system was required for these processes. Alloying nitrogen at a normal pressure can be performed by alloy addition or gas injection. Blowing nitrogen gas is a more economic and advisable method since the nitrogen-bearing alloy is quite expensive and contains high content of impurities. A number of investigations have been reported on the solubility of nitrogen gas in pure iron [2] but few in iron-based multi-component alloys such as stainless steel.In the current study, the effects of steel chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were experimentally investigated with a high temperature induction furnace."

Jan 1, 2011

By Nadia H. Rafat, Iman S. El-Mahallawi, Hussein Badr, N. Khattab, Ahmed A. Abdel-Rehim

The basic part of solar water heaters is the collector and the main functional part of the collector is the absorber layer. In this work, a commercial locally available black painting (PACEN code 10382 colour 890), used for swimming pools solar heating, was modified by adding nano-graphite dispersion. The effect of nano-graphite particles percentage on the spectral absorbance of the material was examined on samples containing two values of 1.5 and 2.5% nano-graphite particles by weight. Fourier transform spectroscopy (FTIR) analysis was also used to identify the functional groups in the developed material. A simple experimental setup was designed to evaluate the performance of the developed nanodispersed selective coating polymeric based material, by measuring the increase in temperature of circulating water. It was shown that adding 1.5–2.5% nano-graphite particles to a polymer based black coating causes an increase in the optical absorptance, and an increase in the circulating water temperature.

Mar 1, 2018

By Takahiko Okura

Sulphur, with its multiple oxidation states, play critical roles in many processes, ranging from regulating enzymes in plants, to acidifying aquatic systems, and to affecting the global climate. Most of non-ferrous smelters have been contributing to reduce atmospheric emissions of sulfur dioxide to acceptable levels, converting it to sulphuric acid and/or gypsum. However, some amount of SO2 gas is still emitted from isolated smelters. Furthermore, sulphuric acid is competing with involuntary elemental sulphur in the market. This situation puts the non-ferrous metallurgical industries to develop a new sulphur fixation process. This paper briefly describes the new technologies for fixation, followed by the novel proposal to convert SO2 gas to elemental sulphur using organic materials. Finally, the feasibility will be presented technologically and economically.

Jan 1, 2006

By Ximeng Zhu

The electrochemical behavior of mineral and coal pyrites in stirred and quiescent alkaline boratelsulfate solutions @H 7.9-10.5) have been investigated using cyclic voltammetry. Significant differences in the electrochemical response of these pyrites were observed. At the mineral pyrite surface, three anodic peaks at about -0.8 V, -0.1 V and +0.5 V (SCE) have been detected along with their corresponding reduction peaks. The first two peaks correspond to FeIFeOI) and FeOI)lFe(III) oxidation. The third peak is present for quiescent conditions but disappears as a distinct peak when the electrolyte is stirred. In the upper voltage region +0.30V (SCE), the current increases markedly during stirring and the reactions correspond to the oxidation of pyrite with the formation FeOII) oxides plus elemental sulfur. Also there is evidence that Fe oxy-ions form. Coal pyrites, under rapid sweep conditions display only the first two anodic peaks, the associated reduction peaks and an additional reduction peak corresponding to one or more of the high voltage oxidation products. After prolonged exposure to high potentials, coal pyrite displays reactions similar to those of mineral pyrite but at much higher current densities demonstrating the much higher reactivity of the coal pyrite. The reactivity sequence was Upper Freeport coal pyrite > Pittsburgh coal pyrite > mineral pyrite.

Jan 1, 1991

By Reinhard F. Dobner

After a short introduction about the HK's secondary smelter process and explanations concerning the anodes produced the regulation and buffering of bleed will be described and the principles of technology for processing of bleed will be presented. Modernization aspects, especially installation equipment, and the different types of evaporators used will be described in detail. Besides, experience made with acid-resistant materials - stainless steel, enamel, plastics - will be reported. Environmental aspects such as water and air pollution will be outlined briefly and in conclusion the quality of products obtained as well as quality control will be presented.

Jan 1, 1997

By Kexin Jiao, Huichang Song, Zhijia Zhang, Jianliang Zhang, Zhengjian Liu

A clear understanding of iron carburization reaction occurring between molten iron and carbonaceous materials is of great importance in blast furnace, and it is one of the hot spots that ironmaking workers pay close attention to. Although carburization rates between iron and coke have been studied, the factors directly controlling it have not been clearly identified. This study focused on the kinetics analysis of iron carburization reaction. Sulfur content was determined as having positive influence on graphite carburizing reaction rate in the range of 0.02% - 0.06%. The values of apparent activation energy calculated by the experiment are consistent with the existing literature, which in turn proved the reliability of the experimental data.

Jan 1, 2015

By R. Hurman Eric

The electrode in a slag-resistance electric furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power, i.e. heat needed for the operation. The control parameters are the size and positioning in the slag bath which are defined by slag resistivity, furnace resistance, cell constant and power input sequence all of which are closely interrelated. The flow of heat generated by the electrode current determines the energy distributions and thus the furnace dimensions. Heat flow models concerning vertical, horizontal and combined two-dimensional flows are discussed. All these considerations are based on the experimentally determined slag properties such as its resistivity.

Jan 1, 1995

By Ari JokiIaakso

Three different sulphidic raw materials were treated in a laboratory scale laminar flow fur-nace simulating suspension smelting conditions. The materials were a pure chalcopyrite concentrate, a high-antimony concentrate (tetrahedritic), and crushed copper mattes. The gas preheating temperatures were 500 -1 100°C ana the atmospheres ranged from N2 to N2 -75 % O2, Two particle size fractions were used for the concentrates with x = 20 -38 um and x = 62 -74 um, and three for the granulated copper mattes with x < 37 um, x = 62 -88 um, and x = 125 -177 um. Scanning electron microscopy combined with energy dispersive analysis and backscattered electron analysis was used for determining the morphology and the mineralogy of the reacted particles. Fragmentation of the particles were observed in all materials during the flash oxidation, the conditions depending on the iron and sulphur content and the original particle size fraction of the material. The melting and/or reaction stages of the particles in different conditions were studied from powder samples. Polished sections were examined in order to follow the development of porosity and the mineralogy of the particles.

Jan 1, 1989

By He Zhi-jun, Ning Zhe, Pang Qing-hai, Zhang Jun-hong, Zhan Wen-long

In this study, Raman spectroscopy was utilized to investigate the evolution of char structure in pulverized coal (PC) during microwave irradiation. The results indicated that though microwave treatment was carried out at low powers of 132W or 264W, significant variation in char structure was still observed. Char structure turned out to be more irregular firstly under microwave irradiation. However, char structure of superior regularity was obtained with the extension of irradiation time. It can be conclude that short time microwave treatment may facilitate the chemical activity of coal, while long time microwave irradiation on PC may deteriorate its combustion or pyrolysis property.

Jan 1, 2016

By Frank Mucciardi, Hujun Zhao, Pietro Navarra

"A heat pipe is a device having a very high effective thermal conductivity in which two-phase flow and heat transfer takes place. Recent research at McGill University has led to a new type of heat pipe that contains a flow modifier. This improvement has enabled the device to operate at the high heat fluxes encountered in the metallurgical industry.This paper summarizes the progress made to describe the fluid flow in the evaporator section of a McGill heat pipe with the goal of understanding how the flow modifier configuration is linked to the film boiling and dry-out limitations. A separated flow model, an instability analysis, a lift-off model and an energy balance model are used to calculate the theoretical CHF with varying flow modifier configurations and operation conditions. A summary of the current work to relate the flow modifier to the dry-out limitation is also given.Determining how the flow modifier affects both the film boiling and dry-out limitation will give insight into improving the flow modifier design so as to extend the operational range of McGill heat pipes in terms of maximum heat flux and heat load capabilities.IntroductionThe McGill heat pipe is a specialized two-phase heat exchanger developed for several metallurgical applications where temperatures and heat fluxes are typically close to or beyond the maximum safe range of conventional cooling technology.Over the last few years, several breakthroughs have brought this device beyond the proof-of concept stage and a series of industrial trials have been performed with success. These trials include two oxygen injection applications for the ferrous and non-ferrous industry [l], and two light metals permanent-mould casting applications [2,3]. Current projects include a blast furnace copper taphole cooling application [4], a copper smelting application and a thermal analysis probe application."

Jan 1, 2004

By Lv Guozhi, Ren Xiaodong, Liu Yan, Dou Zhihe

"This paper investigated a new desulfurizer, dolomite and ferrosilicon. Magnesium vapor produced by silicothermic reduction of dolomite and ferrosilicon in an immersion tube of molten iron was injected into the molten iron by carrier gas through the underpunch of the tube and desulfurization reaction occurred. In order to explore the desulfurization process of molten iron by the new desulfurizer, the thermodynamics, and experiments of magnesium vapor production and desulfurization have been studied. Through thermodynamic calculation, the reaction temperature of magnesium vapor production by 75ferrosilicon and light-burned dolomite is 1838K in the standard state and decreased with the decreasing partial pressure of magnesium vapor, PMg· When PMg=25kPa, the reaction happens at 1673K. From experiments of magnesium vapor production, reduction efficiency of Mg vapor is about 60 % in 15 minutes at 1673K. From hot metal experiments, the desulfurization efficiency is 89.35%, and the lowest sulfur concentration after desulfurization is 46ppm.IntroductionPretreatment desulfurization of hot metal has become a necessary step in modem optimizing steelmaking process for its cheap cost, which can not only liberate of blast furnace productivity and reduce the burden of produce steel, but also effectively improve overall economic efficiency of the iron and steel system[l-ZJ_ At present, injection magnesium particle is one of the two main methods of desulphurization in hot metal owing to its strong affinity for sulphur, low amount of slag produced, low iron loss in slag skimming and low equipment investment[3l. However, there are still some insufficiencies on the hot iron pretreatment with magnesium particles at present[4-5l"

Jan 1, 2013

By A. Cullaj

Several industrial sites suffer from the contamination of soils from heavy metals, which are emitted among others by anthropogenic mining and metallurgical activities. Effective and economic physicochemical technologies for remediation of these sites remain complicated and costly. A new alternative remediation technique is the so-called phytoremediation. This is based on the ability of some plants to accumulate very high concentrations of metals from soils and thus providing the basis for a remediation of the contaminated sites. This technique as an emerging branch of natural biotechnology, has several advantages compared to the sophisticated physicochemical techniques of soil remediation. It is not only environmentally friendly but also its costs are quite low since it is solar driven. Furthermore plants can accumulate metals to such levels that the mineral recovery maybe feasible even in conventional Ni refinery or smelting operations. In this work, thc potential of many plants to accumulate nickel has been investigated in order to identify the species which offer the best phytoremedial potential for nickel contaminated soils in Albania. Field surveys have been made in five nickel-containing sites in order to identify the nickel tolerant species that have spontaneously grown in contaminated soils. Atomic Absorption Spectrometry measurements were carried out on 145 different plants collected. 16 of them were identified as having an hyper ability to accumulate nickel since they contained more than 10 000 mg Ni per kg (DW). Seven taxa are of Alyssum genus and one of Bornmuellera genus of Cruciferae. The highest accumulation of nickel was present in aerial parts of Alyssum murale var. chlorocarpum Hausskn (25 500 mglkg or 2.5%) and Alyssum markgrafli O.E. Schulz (23 700 mg/kg or 2.37%). The seeds germinated are more evidenced at A.m.var. chlorocarpum, about 63%. These plants are suggested as the most promising species to be used for phytoremediation purposes in nickel contaminated soils and phytoextraction of nickel.

Jan 1, 2003

By G. B. Harris

Much has been written over the past decade concerning the disposal of arsenic from metallurgical processes. In Canada, there are proposed regulations which would classify arsenic in the Primary Group of twenty one persistent, toxic pollutants to be banned or phased out. Since many nickel and cobalt ores, not to mention those of copper, gold and uranium, contain significant amounts of arsenic, it is pertinent to assess the current state-of-the-art of its disposal. The literature is reviewed, and it is demonstrated that from a purely chemical point of view, the family of ferric arsenates largely immobilize arsenic. There is clear evidence from laboratory studies that both crystalline ferric arsenate (scorodite) and amorphous ferric arsenates in which the molar Fe/As ratio is at least three (Fe/As = 3) have very low arsenic solubility; plant data are given to support this. The debate over the long term stability of these compounds continues however; the evidence presented for long term stability and for compound breakdown is critically reviewed in the light? of the recent structural studies, and the role of base metals in these compounds evaluated. Finally, conclusions are drawn as to the viability of a purely chemical process for the long term disposal of arsenic from metallurgical processes.

Jan 1, 1993

By Z. Smieszek, J. Botor, Z. Miczkowski, S. Sobierajski

"From 1978, the direct process for the smelting of chalcocite concentrates in a flash furnace by the Outokumpu method has been applied at the Glogów II copper smelter. The chemical composition of these concentrates make it necessary to control the process very strictly. In this paper, the method for controlling and measuring the main technological parameters of the copper production by flash smelting is being presented. It includes the determination of the chemical composition of the concentrate, its grain structure, the temperature of liquid products of the process, oxygen content in process gases, as well as lead concentration in copper and copper concentration in slag.The main process parameters are determined from the mass and energy balances. The relations between parameters, such as an effect of grain structure of a concentrate on oxygen and oil consumption, and dependence of chemical composition of a concentrate on capacity and products quality are discussed. 1. IntroductionThe Polish copper concentrates, as most concentrates occurring worldwide, contain from 18% to 30% Cu, and less sulphur (7-11%) and iron (2-5%). The main copper-bearing mineral contained in the concentrates is chalcocite, while bornite and chalcopyrite are present in smaller quantities. Moreover, the organic carbon (5-7.5%), arsenic (0.05-0.3%) and lead (1.2-3.0%) are also contained in the concentrates. The gangue consists mainly of silica, aluminosilicates, calcium carbonate and magnesium carbonate. Their proportions make the addition of slag-forming agents unnecessary.The composition of Polish concentrates, especially their low iron content, allows their application in the direct flash smelting process for blister copper production. Low sulphur content is the factor which determines the necessity of oxygen application in this process."

Jan 1, 1989