Search Documents

By Vinay Kumar

The disposal of large quantities of electronic scraps generated world wide is causing not only environmental problem but also loss of resources. Therefore, R & D efforts have been made to develop a suitable process for extraction and separation of metals viz. copper, zinc, cadmium and nickel expected from the leaching of e-scraps using solvent extraction process. Different process parameters viz. pH, aqueous to organic ratio, kinetics of extraction, extraction isotherm to establish stage requirement for extraction in continuous mode etc have been studied to optimise the condition for the separation of metals. The studies showed the selective extraction of copper after iron precipitation from the sulfuric acid leach solution of e- wastes containing ~1.0 g/L Cu and minor impurities with 2-hydroxy-5- nonylacetophenoneoxime (LIX 84) above pH 2.0 in single stage. A scheme for separation of cadmium, zinc and nickel has been proposed using di(2-ethylhexyl) phosphoric acid (D2EHPA) under controlled pH of the aqueous solution. The order of extraction was found to be Zn> Cd> Ni.

Jan 1, 2009

By Y. K. Rao

In the carbonyl process for the refining of crude nickel CO(g) reacts with nickel in the 310-370K range producing nickel tetracarbonyl, Ni(C0)4(g). Iron and cobalt impurities also form gaseous carbonyls but their partial pressures are low. The carbonyl is led to a decomposer plant wherein the gas disproportionates in the 500-600K range depositing pure metal on nickel pellets that move countercurrent to the gas-flow. This system serves to illustrate the fundamental principles involved in the vapor phase mass transport of elements, against temperature-gradient, under the influence of chemical potential gradient. Unlike in the crystal growth, the source is at a lower temperature (say 350K) whereas the seed is in the hot-zone (say 550K) of the closed ampoule-type reactor. By assuming virtual gas-solid equilibria in the end zones, with diffusion of gaseous species between them acting as a slight perturbation, the quasi-steady- state mass-transport rates are computed for a range of CO-pressures and temperatures.

Jan 1, 1993

By J. Pérez

A lead smelter slag with high copper, lead, arsenic and silver contents was treated at laboratory scale for arsenic removal. The slag was first leached at atmospberic pressure with sulfuric acid and oxygen. According to arsenic contents leaching of most of the arsenic was achieved in either one or two stages, producing a lead-silver rich residue and a solution high in copper and arsenic concentrations. Alternative routes were considered to treat the resulting solution. Firstly, solvent extraction of arsenic with a mixture of TBP and 2-etbyl-bexanol was tested and extractions of over 95 percent of arsenic were achieved. Secondly, a copper arsenate precipitation treatment was done to eliminate arsenic and copper from solution.

Jan 1, 1996

By Hongbo Zhao, Jun Wang, Wenqing Qin, Guanzhou Qiu, Xueduan Liu

Bio-hydrometallurgy technology was applied for the extraction of copper from the raw ores of Chambishi Mine in Zambia. A copper extraction of 93.29% was obtained for small scale column bioleaching within 63 days, while a copper extraction of 89.05% was achieved for large scale column bioleaching in 90 days, thus confirming the amenability of the raw ores for effective extraction via bioleaching. The bacteria were cultured in a 6-stage enlarge cultivation. The bacterial cultures with cell concentration of more than 1×108 cells/mL were added into a spray pond of sulfuric acid to be applied in the dump leaching, and a copper extraction of about 50% was achieved within 2 months. The production report revealed that the copper extraction increased by approximate 20%, and the acid consumption was reduced to around 35% as a consequence of adding the bacteria. The industrial demonstration of the bio-hydrometallurgy technique is now well established in Zambia, and further applications of bio-hydrometallurgy in both Zambia and Congo are currently in progress.

Jan 1, 2015

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"The disposal of wastes is a serious environmental problem, since available landfill space is dwindling. Their treatment by pyrolysis or combustion has merit, and the corresponding fuel or power production is of technological interest. However, such processes need a rigid control of emissions. This work addresses the gaseous light hydrocarbons (LHCs) generated during sequential pyrolysis and partial oxidation of unserviceable tires, PET bottles, com wastes (DDGS) and sugarcane bagasse in a two-stage laminar-flow horizontal furnace, kept at 1000 °C. Gas chromatography was used to identify and quantify the components of the emitted gaseous light hydrocarbons. The results showed that the biomass residues generated the highest emissions of aliphatic hydrocarbons, whereas PET generated the most aromatic hydrocarbons. When stainless steel meshes were inserted in the exhaust flow, it was found that hydrocarbon emissions were curtailed; as such meshes catalyzed partial conversion of these carbon-bearing gases to carbonaceous nanomaterials.IntroductionLight hydrocarbons (LHCs) are volatile organic compounds, consisting of hydrogen and carbon with low molecular weight; the most common species are methane, ethane, propane, butane, etc. LHCs are valuable since they are a very important energy resource. However, uncontrolled release of light hydrocarbon gases to the atmosphere should be avoided [l, 2]. In this work, a development is presented for the evaluation of LHCs generated during the controlled pyrolysis/combustion of several wastes in a two-stage laminar-flow horizontal furnace. Samples of unserviceable tires, post-consumer PET bottles and waste residues from the bioethanol industry (DDGS and sugarcane bagasse) were burned. A catalyst system, consisting of stainless steel screens, was tested for its effects on the gaseous emissions."

Jan 1, 2011

By Hubert Bril, Priscilla Pareuil, François Bordas, Emmanuel Joussein, Jean-Claude Bollinger

"According to the legislation, valorization type, origin and characteristics of waste material, various standard procedures are available to evaluate environmental impacts. A Mn-rich slag was sampled from a metallurgical plant. After its characterization (elementary analysis and mineralogy), five standard procedures were carried out (i.e. TCLP, EN 12457-1). Each fixed parameter of the standards was systematically studied in a large range: pH, Liquid/Solid ratio, contact time. For example, EN 12457-1 led to a low ME mobilization, increasing with the L/S ratio, the contact time and an acidic pH. As a conclusion, the representativeness of the considered parameters and their potential variations are predominant to assess of the real environmental impact during slag reuse. Introduction Recent studies have been carried out about environmental impacts of waste containing metallic elements (ME) because of their potential mobility [1-7]. Indeed, slags are either dumped or valorized in various activities such as building materials. In order to assess environmental risk, various standard procedures are used depending on country legislation, origin of waste and valorization way. Results of leaching tests are linked either to special legislation (e.g. Dumping: EC, Council Decision 2003/33/EC, Construction products: EC, Council Directive 89/106/EEC) or to legal levels used in drinking water (Directive 98/83/CE) when leachates could migrate to groundwater. If ME in leachates are lower than drinking water authorized levels, the waste will be considered as non-hazardous. On the contrary, if the leachable amounts exceed them, the question about the risk has to be posed. Beyond the abundance of leaching tests available, variety of operational conditions induced by these regulatory tests does not make the choice easier. According to operational conditions induced, ME release could vary from one test to another one. ME concentrations in leachates depend on pH, Liquid/Solid ratio, contact time and particle size [3]. To highlight the importance of these operational parameters, potential risk for valorization of a manganese-rich slag was assessed by comparing several standard leaching protocols [8-12] with a global study dealing with the influence of operational conditions. For each regulatory protocol, the most influential parameters (L/S ratio, pH, particle size and contact time) have been studied in a large range."

Jan 1, 2008

By Jean-François Boulanger

The production of rare earth elements from ore usually consists of three steps; the separation of a concentrate of REE bearing minerals; the cracking of the REE minerals to liberate the REE into an aqueous solution and separation of REE into individual elements. This paper describes the results of laboratory tests conducted on a carbonate-rich REE ore containing bastnaesite and monazite. The tests cover the whole processing sequence of beneficiation, preparation of the REE solution using a caustic leach followed by acid leach to break monazite and bastnaesite and liberate REE into an aqueous solution and the partial separation of the REE using solvent extraction. Details on the product quality and process performances (recovery and impurities removal) are given for each studied step. The paper also discusses the economic advantage of separating the REE rather than producing a mixed REO product to be sold to a refinery for REE separation. A mini-pilot plant version of the process is currently planned.

By Pedro Lobarinhas

In the present work a two dimensional computational model is derived for the description of the time dependent heap leaching process. The flow inside the heap is calculated using the diffusion equations for the flow in porous media. The soil conductivity is also estimated assuming a close packed structure for the grain packing inside the heap. These equations, with appropriate boundary conditions, are solved using a time step splitting scheme. From this calculation the amount of leaching reagent in contact with the ore at any position inside the heap can be calculated and, once coupled with appropriate reaction equations, the amount of metals extracted can be computed and leaching agent concentration updated. The model is tested with available experimental data and the results have shown to be in a very good agreement. The model predicts all the transient features of the data.

Jan 1, 1999

By Kexin Jiao, Zhijia Zhang, Jianliang Zhang, Zhengjian Liu

Carburization behavior of molten iron in blast furnace is an essential part of BF long campaign technology. Maintaining carbon content stable is an important prerequisite to ensure the high production of the blast furnace. In this paper, the important aspects of the research progress which mainly including the study of iron carburization at the upper and the lower parts of the blast furnace was reviewed. Indirect carburizing is the main way at the top of the blast furnace. The content of carbon in metallic iron increases with the reducibility of iron ore improved. The thermodynamics and kinetics conditions are good for carburization reaction to take place at the bottom of the blast furnace. Carbon content of molten iron increased by coke carburizing. Meanwhile, the drawbacks of the existing literature on iron carburization behavior were analyzed and new research directions of iron carburization were proposed in the future.

Jan 1, 2015

By Matthias Merzkirch, Volker Schulze, Kay Andre Weidenmann

"Unidirectionally reinforced light weight compounds based on light metals such as the aluminium alloy EN A W-6082 are adequate materials for the future use in transportation means like automobiles and airplanes. Due to the occurring cyclic loads knowledge about the crack growth behaviour of such composites is needed. The investigations at a load ratio of R = 0.18 show that the crack growth rate of the aluminium matrix is reduced if reinforced by spring steel wire with a reinforcing ratio of only about 1 Vol.-%. Additionally, the acoustic emission analysis allows detecting crack growth within the matrix material, crack propagation along the interface wire/matrix and crack closure which could also be determined with the help of a self designed capacitive displacement measuring gauge. The damage behaviour could be verified by metallographic and SEM investigations.IntroductionIn the field of lightweight structures for transportation means the need for light, strong and stiff materials, in particular composite materials, is increasing in order to save resources and costs. Lightweight materials such as aluminium and magnesium alloys are highly efficient candidates to be used in the composite extrusion process [1] which allows for a simple production of unidirectionally reinforced profiles with a large diversity of geometries at low costs. Figure 1 depicts the principle of the composite extrusion process; within the first part of the tool the billet material is split into several strands whereas the middle part of the tool allows the supply of the reinforcing elements. The third part of the tool rejoins the matrix material and the reinforcing elements and defines the final shape of the profile."

Jan 1, 2011

By Sutham Niyomwas

Synthesis of alumina-mullite-silicon carbide composite (Al2O3-Al6Si2O13-SiCw) was obtained in situ by carbothermal reduction of a mixture of kaolin and two different silica sources. The carbothermal reduction was carried out in a horizontal tube furnace under flow of argon gas. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The synthesized products were mixtures of alumina, mullite and silicon carbide in the form of whiskers. The effects of adding two different silica sources of rice husk ash and silica powder to the mixture of kaolin and activated carbon were investigated. XRD and SEM analyses indicate complete reaction of precursors to yield Al2O3- Al6Si2O13-SiC as product powders, with the SiC having whisker morphology.

Jan 1, 2006

By Qingchun Yu, Baoqiang Xu, Yongnian Dai, Bin Yang, Fulong Zhu

"In this paper, the mechanism of the carbothermic reduction-chlorination process to extract aluminum from alumina in vacuum was investigated. The carbon monoxide (CO) content of the gas, phases of the reduction slag, surface morphology of the reduction slag and the product aluminum were measured by means of gas chromatography (GC), XRD, and SEM. The experimental results indicated that the content of CO in the gas decreased, but Al4C3 increased with time at 1773K during the carbothermic reduction process of alumina. AlCl(g) and graphite (C) were produced by the reaction between Al4C3 and AlCh(g) at 1773K, and then aluminum beads generated after the decomposition of AlCl(g). It implied the mechanism of alumina carbothermic reduction-chlorination process in vacuum involves three steps as follows: the carbothermic reduction of A}z03 to produce Al4C3, the chlorination of Al4C3 by AlCh(g) to produce AlCl(g), and the decomposition of AlCl(g) to produce Al(l).IntroductionAluminum is the basic raw material for many industries [1], and it is used extensively because of various excellent properties such as light weight, good malleability, high strength, excellent thermal conduction, high corrosion resistance and so on [2]. Industrial production of aluminum currently includes refining alumina and electrolytic aluminum processes. However, its development has been effected by some factors such as high energy consumption and heavy environmental burdens [3]. In the past several decades, there had been numerous attempts to produce aluminum by new methods. Extracting aluminum from alumina or bauxite directly by carbothermic reduction-chlorination process had been studied [ 4-6]. Although the alumina carbothermic reduction process [7~9] had been studied, the mechanism of the carbothermic reduction-chlorination process had not been systematically elucidated.In order to investigate the mechanism of the carbothermic reduction-chlorination process in vacuum, GC, XRD and SEM techniques will be used to determine the CO content and to characterize the surface morphology and composition of the slags at various temperatures."

Jan 1, 2011

By Kiyoshi Shibata, Jun-ichi Hayashi

"Steel making technology poses strong potentials for environmental protection in three direction. One is pollution control on steel making process itself. Japanese steel industry has cut down various type of emission drastically since 1970's. Secondary, those process technology can be applied to reduce environmental burden in other industrial sectors. One of the successful examples is municipal waste treatment facility. Thirdly, development of high performance steel products, such as high strength steel for automobile body, can contribute to improve environmental performance during their use, based on the concept of life cycle assessment. Some examples of the successful development and future task is discussed.IntroductionsStack and smoke used to be a symbol of energy intensive industry such as steel making. But, scenery of steel works and its surroundings have been completely changed, and steel products have been changing, as well. The steel making industry consumes huge quantities of energy and resources. Variety of technical development have been carried out to reduce the pollutant release. The steel industry in Japan has been making direct and indirect contributions to reducing of various kinds of environmental impacts through development of high-performance process and products: Its potential technical capability accumulated in steel making is fundamental and essential infrastructure for the vein systems of our society. In this paper, the activity of steel making industry for better environment is discussed"

Jan 1, 2000

By Takayuki Watanabe, Yoshiki Shimizu, Yusuke Moriyoshi

"B-C-N nanotubes prepared by a flush evaporation method using a de arc plasma were mainly characterized by transmission electron microscopy (TEM) and electron energy· loss spectroscopy (EELS). The nanotubes obtained· were divided into three types such as carbon boron nitride and carbon or carbon nanotubes surrounded with boron nitride nanotubes. These types of nanotubes were obtained at higher temperatures than about 3000 K, however, these were not formed at lower temperatures than about 3000K. On the other hand, 11anocapsules were· formed at all the experimental temperatures and nanocapsules with a homogeneous phase were obtained at lower temperatures than about 3000 K. The effect of additives on the formation of B-C-N nanotubes was not clear. Based on these experimental data depending on temperatures and corresponding microstructures, the formation mechanisms of both nanotubes and nanocapsules were briefly .discussed 1 Introduction As reported previously, nano tubes have unique electrical properties1, 3) The preparations of nallotupes have been usually carried out by flush evaporation methods using either a de arc plasma or a laser4 -5) By these methods the reaction rate is so rarid that we have no data of intermediate products between initial raw materials and. final products of nanotubes 6-9). So, the formation mechanisms of nanotubes have been mainly speculated only from the microstructures of resultant nanoiubes. In order to have more reliable formation mechanisms, it is particularly important to have the information of intermediate products at the corresponding temperatures. From the viewpoints, we have studied about the effects of temperatures on the preparation of nanolubes. Here we report mi firstly some problems on the preparation of B-C-N nanotubes 10), secondly the effects of temperatures on the preparation of B-C-N nanotubes, and finally the formation mechanisms of nanotubes."

Jan 1, 2000

By Marcelo R. Esquivel

A MmNi5 alloy is synthesized by a combination of mechanical milling and low temperature heating processes. Synthesis time is 40 h for powders milled in a low energy ball mill at room temperature. A reduction in milling time is obtained if massive sample is mechanically milled at shorter times (2 h to 10 h) and heated at temperatures lower (600 ºC) than the usual temperatures used in equilibrium methods (>800 ºC). The alloy formation is detected even at a combination of temperatures as low as 200 ºC and milling times as short as 5 h. The temporal evolution of mechanical milling process was followed by both X-ray diffraction (XRD) and scanning electron microscopy (SEM) to detect the main stages of milling. Four stages were detected: Initial, Intermediate, Final and Completion. These stages were correlated to an enhancement of the synthesis method by combination of times of milling shorter than 10 h and temperatures of heating lower than 600 ºC.

Jan 1, 2006

By K. W. Cathrine Solem

Filtration of liquid aluminium is widely used in the industry for the removal of inclusions, and Ceramic Foam Filters (CFFs) are often the filtration media of choice. It is known that PH3 (phosphine) can be released from used phosphate bonded CFFs when in contact with water. Additionally, there is a need of an improved understanding of the thermal stability and the chemical reactivity of these types of filters, as there is limited information available in the public domain. In the present preliminary study, three CFFs, i.e. Substrate 1–3, with varying AlPO4 (aluminium phosphate) content were studied under controlled conditions. Samples of the substrates, as produced and in contact with 5N pure aluminium, were heat-treated in a vacuum induction furnace at 850 °C and 1300 °C, as well as thermally studied at 850 °C using a Differential Scanning Colorimeter connected to a Thermogravimetric Analyser (DSC-TG). All tests were performed under an inert atmosphere of argon (Ar). Mass changes of ∼0.001 % were registered for the pure substrates, and 0.003-0.10 % when in contact with aluminium. In the latter case, diffusion of P (phosphorous) from the bulk of the substrate to the interface was established to have taken place. A colour change, from white to orange/brown, was also observed at the interface, which is a clear sign that a chemical reaction has taken place. As a result, the thermal stability of the substrates can be questioned under present conditions.

By K. L. Hardee

A recent development has emerged which produces a retrofittable, low cost anode by attaching disposable, electrocatalytically active titanium mesh over the existing lead anodes. The coated titanium mesh anode operates at potentials of several hundred millivolts lower than the lead anode, providing significant power savings. The exposed lead surfaces are stabilized since most of the current flows through the titanium mesh. With the minimal lead corrosion, the sludge formation is virtually eliminated and the purity of the plated copper is greatly enhanced. Further savings may be realized by the elimination of non-essential chemicals such as cobalt. Since the combination anode is stable and uniform, the plated copper is also more uniform with minimal formation of dendrites, reducing the shorting. Full-size anodes have been tested for over 6 months in commercial copper electrowinning cells. The laboratory and field performance of the stabilized lead anode will be reviewed, including the voltage characteristics, the lead stability and the copper cathode purity.

Jan 1, 1999

By Robert B. Haagensen

While light optical microscopy has long been employed by the mineral processing industry, there has been a tendency to shy away from its use for all but the most exacting purposes. Despite the usefulness of micros-copy in solving a wide variety of problems, the response to such work is often less than enthusiastic primarily due to time considerations. Microscopical techniques are therefore often relegated to the "ivory tower" and their direct and practical application to everyday problem solving over-looked. The purpose of this paper is to dispel such attitudes and promote a wider use of light microscopy. Several examples are given which point out the indispensib1e nature of optical microscopy as a rapid means of defining and solving problems in mineral processing. The application of other instrumental techniques to augment the information obtained is also discussed, particularly the value of the combined use of the optical microscope and electron probe micro-analyzer.

Jan 1, 1981

Cospidie (3CaO*2SiO2*CaFe2) is one of the most important compounds crystallized in mold flux films during casting in the continuous casting process of steel, The primary crystallization field of cuspidine has been experimentally developed in the CaO-SiO2-CaF2-SiF4 system. The cuspidine-NaF binary and cuspidine-CaF2-NaF ternary systems have been also experimentally determined to study effects of addition of NaF on the primary field of cuspidine. In order to discuss its thermodynamic stability the standard Gibbs energy of formation of cuspidine has been deterimed by an electromotive force methods using CaF2 as solid electrolyte and a transpiration method as follows: ^fG° (cuspidine) /kjmol-1 = 5198 + 0.825T (+12) (1313<T/K<1329): EMF method ^fG° (cuspidine) /kjmol-1 = 5178 + 0.813T (+8) (1221<T/K<1469): Transpiration method The chemical potential diagram and constituent activities for the CaO-SiO2-CaF2 System have been evaluated based on the obtained thermodynamic data.

Jan 1, 2003

By Patricia Negrini Siqueira

Abstract. Polymers are susceptible to changes in their chemical structures that affect their mechanical properties under weather condition. Exposure of plastics to UV radiation causes a loss in their mechanical properties and/or change in appearance, including reduced ductility, color changes, yellowing and cracking. Today, there are several additive systems (light stabilizers) developed to work according to resin, final application, type of cultivation, and other characteristics. This study evaluates the different additive systems (Hindered Amine Light Stabilizer - HALS, nano calcium carbonate - NPCC, nZnO and nTiO2), applied 0.75% (in weight) in linear low density polyethylene (LLDPE). The samples were mixed by high rotation homogenizer and extrusion. Later, the samples were molded by injection and aged in QUV-B simulating 6 months of exposure to weather. Tests of FT-IR and tensile strength comparing to the non-aged samples were carried out in order to evaluate the performance of several additive systems.

Jan 1, 2015