Search Documents

By Naiyang Ma

Along with steel production, various steelmaking slags are constantly generated at considerably high rates. In general, steelmaking slags are not categorized into hazardous materials and do not cause any environmental issues. Therefore, recycling of steelmaking slags is often aimed at creating values by using the slags to replace high-cost raw materials. Chemical compositions and particle size distributions of slag products from steelmaking slags will determine what raw materials the slag products can replace. Consequently, maximizing the values of steelmaking slags will require to produce slag products with the highest values and to process the slags with the lowest costs. In this paper, several slag processing processes are assessed based on maximization of the values of the steelmaking slags.

Mar 1, 2017

By J. Rastas

The recovery of lead, silver and gold from existing and potential zinc process residues using a sulfidization-flotation method was investigated on a laboratory scale. The following residues were tested: neutral leach residue, high acid leach residue, and hematite residues. The sulfidization of lead and silver is carried out at low pH by the addition of a stoichiometric amount of sulfide at a controlled rate. To increase the particle size of the sulfides, seeding with synthetic lead and silver sulfides -is employed. The flotation is carried out at pH 2-4 using low pH-collectors such as dithiophosphates and dithiophosphinates. Special attention must be paid to the role of oxygen in the conditioning stage. The effect of different parameters on both the sulfidization and the flotation has been evaluated. Recoveries of 85-90, 90-95 and about 80 % were obtained for lead, silver and gold, respectively. Typically, concentrates containing 50-60 % lead, 3-5 kg/t silver and 10-15 git gold were produced.

Jan 1, 1990

By Chidchai Loyprasert, R. A. Stoehr

"A computer model has been developed to predict grain structures in alloys solidified under unidirectional flow using a combination of three techniques -- solution of the equations for flow of an incompressible fluid bounded by curved surfaces by the SOLA-SURF algorithm, calculation of heat flow by a finite difference method, and simulation of grain formation by a two-dimensional cellular automaton (CA) model. The changing rigid surface has been taken into account. Heterogeneous and homogeneous nucleation are considered, and the growth kinetics of a dendrite tip are evaluated by the Kurz-Giovanola-Trivedi (KGT) model. These calculations were applied to solidification of an Al-4.5% Cu alloy flowing over a chill on the bottom of a channel, a system for which experimental results were available. Using a variety of flow rates and superheats, agreement between the computed and experimental results were very good including transitions between columnar and equiaxed grains, the aspect ratio of the grains, and the inclination of the grains to the flow.IntroductionModeling of casting and solidification processes has developed over the years along two distinct tracks: (1.) modeling of macroscopic heat transfer and fluid flow for design purposes, and (2.) modeling of microscopic processes such as nucleation and growth in order to improve the scientific understanding of the phenomena involved. The present work is an attempt to combine the macroscopic and microscopic approaches for the solidification of an alloy flowing over a chill. The specific case chosen is that of an aluminum-4.5 % copper alloy flowing linearly over a water-cooled copper chill for which experimental results were available over a range of flow rates and superheats. For the macroscopic calculations, the SOLA-SURF algorithm for solution of the twodimensional fluid flow equations was combined with the finite difference method (FDM) for calculating heat transfer. For the microscopic calculations, heterogeneous and homogeneous nucleation were considered, and the growth kinetics at the dendrite tips were evaluated. The cellular automaton (CA) technique was used to apply the microscopic kinetics to the temperature and .flow conditions."

Jan 1, 1999

By Chan. C. L., Zehr. R., M. M. Chen, J. Mazumder

"Two three-dimensional models of a surface tension gradient driven flow during laser surface heating are developed. The first model is based on a perturbation solution. The basic solution corresponds to the stationary axisynwnetric case and perturbation is based on a small scanning velocity. The advantage of seeking a perturbation solution, as it turns out, is that the three-dimensional flow is modeled by two sets of two-dimensional equations which are presumably much more tractable than the original three-dimensional equations. Numerical solutions are obtained and discussed. The second model is a full three-dimensional numerical solution of the Navier-Stokes equations, using a point-by-point partially vectorized iteration scheme. Surface shape is also determined in a self-consistent manner. The effect of the presence of convection on pool geometry, cooling rate and solute redistribution is presented and discussed.IntroductionThe existence of fluid flow and convection and their effects were first reported in the fifties (1,2). The role of convection in controlling pool geometry such as pool shape, undercut and ripples, and defects such as variable penetration, porosity and lack of fusion and weld properties such as weld homogeneity and bead formation is studied by a number of researchers and is reviewed by the authors in a recent paper (3).Recently, surface tension gradient driven flow has been identified as one of the forces responsible for convection within the molten pool (4,5). It is postulated that surface tension gradient driven flow is responsible for the surface ripple formation in the weld pool (6-8). Oreper, et al. (9) developed a two-dimensional convection model. Buoyancy, electromagnetic and surface tension gradient forces were considered. The formulation was based on a specified pool profile. It was found that the surface tension gradient is the dominant force in most cases. However, the solid-liquid interface is not known a priori. In fact, the solid-liquid interface, i.e. the pool shape, is a piece of information that the model should be able to predict. A two-dimensional transient self-consistent (i.e. the solid-liquid interface is solved as part of the solution] model for laser surface melted pool was first developed by Chan, Mazumder, and Chen (3)). This model predicted a non-uniform cooling rate, hence non-uniform microstructure. Depending on the Prandtl number (i.e. material) and surface tension number, the shape of the molten region as well as the cooling rate changes. It was also predicted that the recirculating velocity is of one or two order of magnitude higher than that of the scanning velocity. This model provides the detail of the flow field and heat transfer on a plane perpendicular to the scanning direction. However, the front-to-back motion and its effect on heat transfer also play important roles in the physical process, especially for the fact that the recirculating velocity is so much higher than the scanning velocity. Such a motion cannot be obtained from two-dimensional models."

Jan 1, 1986

By Karl A. Gschneidner

The magnetocaloric effect has been known for 120 years and has been utilized for cooling about 70 years. But in the last four years significant advances have been made to show that magnetic refrigeration is a viable and competitive cooling technology. Most of the work has focused on reciprocating devices, but rotary apparati are being developed. To date the magnetocaloric properties have been characterized for more than 200 materials. The magnetocaloric effect behaviors have been classified into three types of behaviors. The most common one is found in magnetic materials which exhibit a second order magnetic phase transition. Magnetic materials which exhibit a first order magnetic phase transition account for the second group of materials. Materials which exhibit multi-magnetic phase transitions make up the third group. The best candidate materials for magnetic cooling over the range from -4 to -1 350 K are also presented.

Jan 1, 2002

By Yuanbo Zhang, Bingbing Liu, Zhuyin Chen, Xiao Kang, Chen Liu

Composite agglomeration process (CAP) is an effective method to utilize the iron-bearing dusts generated in the ironmaking plants, by which the dust percentage in the sinter feed can be increased up to 20 wt %. In the current study, a comparison on behavior of iron-bearing dust in the conventional sintering process (CSP) and CAP was characterized. The results showed, in the CSP products, the scattered iron-bearing dust in the mixture was disadvantageous for the sintering indexes and consolidation of the finished sinters. In the CAP products, the main phase in the iron-bearing dust pellets was well-crystallized Fe2O3 grain particles. In the matrix parts, there were more Fe3O4 particles generated, which caused to high RDI+3.15 and low RI of the finished products. The pellets and the matrix parts were bonded by iron oxides and acicular calcium ferrite.

Jan 1, 2016

By Igor Zh. Bunin

A model for developing electric discharges between sulfide mineral (pyrite) particles under high-voltage nanosecond pulses in a liquid medium (water) is considered. A possibility of electrical breakdowns of liquid gaps between particles under nanosecond pulses is shown. This probability and the energy released in discharge channels depend strongly on the sulfide conductivity.

Jan 1, 2010

By A. Hasko

Phytoremediation is a new low cost alternative technique for remediation of contaminated soils from heavy metals that are emitted by ferrous and nonferrous mining and extracting processes. It is based on the possibility to use several plants that accumulate high level of metals in order to remove metallic pollutants from soils and render them harmless. Phytoextraction is an adjacent new technique that uses these hyper-accumulator plants in order to extract the metals from them using even the conventional smelting or refming processes. In our previous work, an extensive investigation of about 150 plants have been carried and several species were identified that could be used for nickel phytoremediation and phytoextraction because of their high accumulation of nickel. It has been found that five taxa from Alyssum genus specie had the highest ability to accumulate nickel with concentrations more than 10000 ug/g (dry weight) or 1%. The taxa showing the highest accumulation of this metal is Alyssum murale var. chlorocarpum with 28 600 ug/g or 2.86%, a good candidate for Phytoextraction. In this work, in order to optimize the phytoremediation and phytoextraction processes further Absorption Spectrometry measurements and biological studies were carried out to determine the parts of the plants that accumulate the highest amount of nickel and the best biological cycle during which they accumulate the highest amount. The results show that the greatest accumulation of nickel occurred in the leaf material (2.86%) and the least in the roots (0.43%). The investigation of the biological cycle of the genus Alyssum showed that: (1) the seeds germinated between 50 C to 30 0 C and more in 25 0 C; (2) 62.9 % of seeds germinated at A.m. var. chlorocarpum; (3) the emergence is almost continue from March to April; (4) the anthesis occurs from May to July; (5) the ripening of the fruit takes place 30 days after flowering; (6) the dissemination of fruits occurs from September to October. Due to these special characteristics it is reaffirmed that Alyssum murale var. chlorocarpum, as a nickel hyperaccumulator, is the most promising plant to be used for feasible phytoremedation and phytoextraction purposes. Keywords: Key words: Phytoextraction, PhytoRemediation, Nickel accumulators, Alyssum sp., Biological cycle

Jan 1, 2003

By M. Hamamoto, S. Tanaka, K. Noda

"Tamano Smelter or Hibi Kyodo Smelting Co. Ltd. is operating with the Tamano Type Flash Smelting Furnace method which is a flash smelting furnace without slag cleaning furnace but which can discharge a slag equivalent to that from the slag cleaning furnace and with the development or coke combustion technology which is the basis of this world's only one type flash smelting furnace process, the smelter exhibits a low operation cost under high productivity operation. Utilizing this experience and improving it we have developed and put to practice an operation guide system using a general purpose computer in order to further establish s stable operation. In this paper these improvements are described. Background of System DevelopmentWith the recent rapid progress of general purpose computers and improvements in their performance an environment for the use or computer in process simulation at low cost and simple operation has been established. If an accurate operation simulation can be done with the Tamano Type Flash Smelting Furnace the merits would be very great and thus we started development of the system. The official name of this system is Computer guide system for Coke Combustion in the T-FSF and taking the initial letters we call it CCCT. We aim to achieve operation with stable mane grade, temperature and slag loss in the furnace by maintaining the most suitable combustion conditions of concentrate and coke in the flash furnace with the assistance of CCCT to the flash smelting furnace operators.Through several production expansion projects clone in the past by oxygen enrichment the copper concentrate treatment quantity and matte grade have increased step by step as shown in Figure I. Following this increase the difference between the operation calculation results al the initial stage of coke combustion and the actual behavior of furnace (matte grade. temperature in the furnace. etc.) gradually became bigger. Further operation procedures taken by different operators against the same phenomenon were sometimes different depending on each individual, which from time to time caused the operation to become unstable. Prior to the development of the system we checked out thoroughly the weak points of operation calculation procedures which were in practice until that time. The results were analyzed and study was carried out to establish a most suitahle operation calculation procedure and finally we reached this system"

Jan 1, 2000

By T. J. White

Xtaltite is the trade name for a generic technology which exploits the well known insolubility of some minerals, which naturally incorporate toxic waste elements, to consolidate and immobilise a range of inorganic waste products. It is a specific case of synthetic mineral immobilisation technology (SMITE) which is already used to immobilise high level nuclear wastes (HLW. Although HLW is highly toxic, it exists in relatively small volumes, occurs in central facilities and may be stabilised at low waste loading (< 10 wt%). In contrast, heavy metal wastes are of considerable volume, therefore Xtalitite waste forms must routinely accommodate high waste loadings (usually in excess of 30 wt% for a particular toxic oxide or combination of oxides) and be suitable for fabrication in remote locations using relatively simple technology. This paper details the methodology underlying Xtaltite, with particular emphasis given to the interplay between solid state chemistry, durability and economic considerations. Specific reference is made to the treatment of arsenious and mercurial wastes.

Jan 1, 1994

By Gaifeng Xue, Jingxuan Zhou, Shangchao Liu

"Both COD and TOC can characterize organic pollution of coking wastewater. In theory, there is a linear correlation between these two indicators. After continuous monitoring TOC and COD of coking waste water, linear regression relationship between of these to indicators was studied with the use of mathematical statistics. And conversion equation between these two indicators was established, and using t-test method for significance testing. The results showed that the linear relationship of COD and TOC was significant. Also interval estimation of equation slope and intercept were given in the condition of 95% confidence level. A linear regression equation established can be used to indirectly convert TOC to COD with high precision and accuracy.IntroductionBoth chemical oxygen demand (COD) and total organic carbon (TOC) are measure of the degree of characterization for organic pollution of water bodies. The current COD standard analytical methods is Potassium dichromate titration method [1] . there are some disadvantages in this method, such as only part of organic matter in the water bodies being oxidated, the refluxed steps, a long time needed for each measurement, high cost. It is the most important that sulfuric acid silver and mercury sulfate reagents used in the measurement may easily lead to secondary pollution. In contrast, the measurement of TOC is by the method of combustion or Photocatalytic Oxidation. The result could be easily got from the instrument. There are some advantages in this way, such as easy operation, short time and little expenses for each measurement and no secondary pollution 121• In addition, the measurement of TOC has higher degree of precision and accuracy than the measurement of COD both in the determination of calibration standards and actual samples. The meaning and contrast of TOC and COD are listed in the table 1."

Jan 1, 2013

The viscosity of high magnesium content FeO-Fe3O4-SiO2-CaO-MgO slags at nickel flash smelting conditions was investigated using a commercial rotational viscometer. The studied parameters were compositions of slag and temperature. The viscosity of these slags was measured as a function of CaO, MgO, SiO2, FeO. Fe3O4 and Fe/SiO2 in temperature range from 1473K to 1723K. These slags contained 5.81 to 10.59 pct MgO, 0 to 10.37 pct CaO, 28.21 to 36.21 pct SiO2, 39.40 to 55.42 pct Fe and 1.1 to 1.5 Fe/SiO2.

Jan 1, 1999

By Roberto Parra

The classic criteria of the preparation of the charge for the smelting of copper concentrates in at flash furnace considers the mass and energy balance from the chemical and mineralogy composition of the concentrates. The operation parameters fixed with this method don&apos;t assure the stability of the operation and the critical problems of the slag quality and dust formation occurs very often. This paper presents the results of a laboratory test that allows the prediction of the behavior of concentrates blends in the view of the minimization of the dust formation and the magnetite control in the slag. The combustion of different copper concentrates and blends were done in a drop tube furnace The results show that the magnetite and dust formation don&apos;t have a linear behavior with the weight proportion of the blend and some optimal blends of 2 or 3 types of concentrates can be identified. From the reasonable hypothesis that the qualitative behavior of blends in the drop tube represents the real behavior in the burner, the preparation of the charge with this approach could help to solve those operational problems.

Jan 1, 2003

By Mingming Zhang, Ramana G. Reddy

"Carbon dioxide (CO2) is one of the most common by-products produced during light metals production. It is considered to be the cause of greenhouse effects. Efficient reduction of CO2 can help minimize the rate of global warming and improving energy sufficiency. In this paper, a novel light metal production process was developed using ionic liquid electrolytes. This process has significant advantages compared to the traditional high temperature processes such as zero CO2 and CF4 emission, low energy consumption due to the low temperature operation and nonconsumable electrodes. Two types of anode materials (graphite, extruded carbon) were tested in electrolysis experiment. The results showed that both anode materials were stable (negligible weight loss). However, the extruded carbon was found to be superior to graphite in terms of current density and current efficiency. The calculated energy consumption for aluminum production was less than 10 kWh/kg at current densities up to 300 A/m2.IntroductionGlobal demand for ultra-light, ultra-strong, recyclable metals is growing as the world switches to low-emission vehicles, energy-saving devices and sustainable products. Aluminum demand is forecast to climb by 30 percent; magnesium demand by 200 percent, while for the emerging industrial light metal, titanium, the demand is expected to be at least double in the next decade. However smelting of light metals is the most energy intensive among all the steps of light metals production. For example, on an average it takes about 15.7 kWh of electricity to produce one kilogram of aluminum from alumina [1, 2, 3]. Advancements in energy efficiency have been steady, but slow, and most U.S. aluminum smelting production operates at 95% current efficiency. Besides high energy consumption, another major concern of the light metals smelting process is the emissions of greenhouse gases (GHG). Electrolysis green house gas emissions in the Hall-Héroult process can be split into three groups: 1) reduction reaction emissions, carbon dioxide (CO2) and carbon monoxide (CO); 2) process upset perfluorocarbons emissions; and 3) hydrogen fluoride (HF) formed from the moisture (H2O) present in the raw materials [2, 3]. Hydrogen fluoride gas can be captured and returned to the cells by the alumina dry scrubbing system used in modern facilities. A total of 5.31 kilograms of CO2 is generated from the reduction process for each kilogram of aluminum produced in the average U.S. primary facility. The perfluorocarbon emissions are related to the “anode effect.” If the concentration of alumina in the bath becomes too low, other reactions between the carbon anode and the bath occur and tetrafluoromethane (CF4) and hexafluoroethane (C2F6) are generated. These gases have high global warming potentials (GWP), which is a ratio developed to compare the ability of each greenhouse gas to trap heat in the atmosphere relative to carbon dioxide"

Jan 1, 2008

By Sergio N. Monteiro

Natural lignocellulosic fibers are successfully replacing synthetic fibers in many engineering applications. In addition to well-known conventional lignocellulosic fibers, others with promising properties are now being considered. The present work investigated the mechanical and structural characteristics of a relatively high strength fiber, curaua (Ananas erectifolius) from the Amazon region of Brazil. The results obtained from tensile tests confirmed the superior strength while scanning electron microscopy (SEM) analysis displayed features that justify the possibility of using the curaua fiber as an effective reinforcement for polymeric composites.

Jan 1, 2006

By De-qing Zhu, Jian Pan, Tie-jun Chun, Dong Chen, Yu Cui

"A study of processing pyrite cinder and metallurgical slag using “one step” technology in strand grate - rotary kiln is presented, which aims to efficiently recover the valuable metals of iron, lead, zinc and copper. The effect of chloridizing roasting parameters including roasting time and temperature on the removal rates of nonferrous metals was investigated. It is shown that copper and zinc are difficult to remove and lead is removed more easily. The preheated pellets were reduced in a rotary kiln, where zinc and lead can be removed easily and high iron grade and good metallurgical performance prereduced pellets can be obtained. Furthermore, the chlorination and the reduction mechanisms of copper, lead and zinc are discussed. It is revealed that the phases of copper, lead and zinc in slag are complex and ferrite and silicate of metals are difficult to remove.IntroductionAs two kinds of significant secondary resources, metallurgical slag and pyrite cinder contain not only abundant iron but also considerable copper, lead, zinc and so on. Several tens of millions of tons of metallurgical slag and pyrite cinder are discharged in nonferrous metal and chemical industries annually in China [1, 2]. In addition, the accumulated waste slag in storage is more than one hundred million tons, which not only occupies much land but also pollutes the environment [3]. However, because the metallurgical slag and pyrite cinder are treated by high temperature processing, the properties are distinctly different from the properties of natural ores, and iron is in close association with copper, lead and zinc. So, metallurgical slag and pyrite cinder are difficult to efficiently utilize and only a small amount is used as additives in cement, paving, brickmaking and auxiliary additives [4-7]."

Jan 1, 2011

By Luiz A. Teixeira

This paper reports the results of kinetic studies involving the precipitation of arsenic from aqueous solutions as FeAs041 Fe(OH)3&apos; using FeS04 as source of Fe ions, and Air or H202 as oxidizing agents. Both systems lead to an efficient removal of arsenic. The differences in oxidants performances are in the precipitation reaction rate -much faster using hydrogen peroxide. Mechanisms of reactions were suggested based on the following main steps:

Jan 1, 1996

By C. Alexandru Sonoc

Donnan Dialysis uses ion exchange membranes to extract and separate cations. The driving force is provided by differences in chemical potential, rather than by electric fields or pressure. A Donnan Dialysis based process to recover lithium, nickel, cobalt, manganese, and organic acid lixiviant from recycled lithium ion battery cathodes is under development. In this paper we present a model of Donnan Dialysis and results of simulations of the aforementioned process. The simulations show that 170 m2 of membranes can process 1000 L of leachate ([Li+] = 0.285 M, [Co2+] = [Ni2+] = [Mn2+] = 0.095 M, pH 2) in two days and recover 94.1% of the lithium (as lithium carbonate), 99.4% of the transition metals (as mixed sulphates ready for solvent extraction), and all of the organic acid using 423 mol of H2SO4 and 268 mol of KHCO3.

By Anja Pfennig, Thomas Böllinghaus, Marcus Wolf

During CCS components are exposed to a corrosive environment and mechanical stress which results in corrosion fatigue and is inevitably followed by the lifetime reduction of these components. The lifetime reduction of the cyclically loaded high alloyed stainless injectionpipe steel AISI 420C (X46Cr13, 1.4034) constantly exposed to highly corrosive CO2- saturated hot thermal water is demonstrated in in-situ-laboratory experiments (T = 60 °C, brine: Stuttgart Aquifer, flow rate: 30 l/h, CO2) in an environment similar to the on-shore CCS-site in the Northern German Bassin. In-situ tension-compression experiments were established simultaneously along with electrochemical measurements using a newly designed corrosion chamber in a resonant testing machine at a frequency as low as 30 – 40 Hz. In addition technical CO2 was introduced into the closed system at a rate close to 9 L/h. S-N plots, micrographic analysis and surface analysis of the fracture surface are demonstrated. X46Cr13 (surface roughness Rz = 4) reached the maximum number of cycles (12.5 x 106) at stress amplitude of 173 MPa producing a low scatter range of 1:3.5. Hydroxide and siderite layers were found on pits and crack surfaces. No typical fatigue limit exists. Pit corrosion prior to crack initiation may be identified as failure cause.

Jan 1, 2016

By Dandan Jian, Christian Karcher

Information of liquid steel flow patterns inside the mold may be obtained from the velocity at the free surface (meniscus). This meniscus flow may be measured using the contactless electromagnetic technique termed Lorentz force velocimetry (LFV). It is based on the measurement of Lorentz forces acting on a magnet system when an electrically conducting metal melt interacts with the field lines stretched by the magnet system. Force sensor and the magnet system form a so-called Lorentz force flowmeter. In this paper we present a series of model experiments that demonstrate the feasibility of using two identical flowmeters that are arranged in a certain distance one behind the other. In this case, surface velocity may be determined by just cross-correlating the two force signals recorded by the two sensors. This technique is called time-of-flight LFV. A special prototype of a respective measuring device, called meniscus velocity sensor (MVS), has been developed to measure local free-surface velocity. In the present paper we describe experimental results of respective measurements in the model test stand LiMeSCo (liquid metal surface velocity correlation). To check the potential of the time-of-flight technique, in a first step we measure surface velocities during solid-body rotation of metallic substances. We observe that small modulations in the signals that are due to the natural unevenness of the solid body can be used to determine surface velocities. In a second step we apply the time-of-flight technique to liquid metal free-surface flow. Here we use the low-melting eutectic alloy GaInSn as a test melt. In this case we observe that the cross-correlations between the signals are much rarer and much weaker than in the solid-body experiments. We conclude that the presence of the localized magnetic fields, produced by the permanent magnets of the flowmeter, give rise to intense deformation of the free surface and the creation of surface waves. The field acts as a magnetic obstacle. We observe that the flow velocity is decreased right underneath the magnetic field and is accelerated in the side regions. This magnetic obstacle effect may restrict the determination of the local surface velocity in application.

Jan 1, 2012