Search Documents

By J. K. Brimacombe

Plant trials have been conducted at the Tacoma Smelter of ASARCO to assess the effect on tuyere blockage and refractory erosion at the tuyere line, of increasing the injection pressure of air into a Peirce-Smith con¬verter. Four tuyeres each having an ID of 19.1 mm (3/4 in) were installed toward one end of the tuyere line of the No. 4 Converter. Air and oxygen-enriched air were injected at 414 kPag (60 psig) through these tuyeres and at the usual 83 kPag (12 psig) through the remainder of the tuyeres in an otherwise normal converter campaign. The test campaign consisted of 88 charges and lasted for 89 days. During this period, punching of the high-pressure tuyeres was found to-be unnecessary; and when, as a precaution, the tuyeres were cleaned by hand at the end of a charge, they were always open. Also it was observed that the flow of high-pressure air remained constant. Accretion formation around the tip of the high-pressure tuyeres varied from charge to charge and was influenced by the matte grade and the level of oxygen enrichment.

Jan 1, 1983

By Zhongliang Tian, Yun Cheng, Yexiang Liu, Ming Jia, Yanqing Lai

"A fundamental electrochemical study of Si ions in Na3AlF6-LiF melts and electrolysis using liquid cathodes was conducted. Cyclic voltammograms (CVs) clearly showed the depolarization of silicon deposition on liquid cathode by forming chemical complexes with the liquid solvent metals. Besides, co-deposition of Al and Si is possible when Si ions are insufficient in the molten salt. Based on the electrochemical results, silicon diffusion into liquid cathode is modelled and evolution of Si activity with concentration is deduced by a mathematic approach. Electrochemical study using liquid metals as working electrodes, can be used as an alternative approach for the acquisition of basic data on alloy behavior. Galvanostatic electrolysis showed that liquid cathodes are appropriate to collect the deposited solid silicon and the highest collection efficiency is almost 85%.IntroductionRecent years have witnessed an increasing demand for solar-grade silicon (Si) by the photovoltaic industry [1-4]. The preparation of high-purity metals through electrolysis and electrorefining offer many advantages such as low cost, low-energy consumption, and environment-friendly process, and thus has been widely used worldwide. From the perspective of electrochemistry [5-7], by utilizing the electronegativity difference between the impurities and Si and controlling the relevant process parameters, it is possible in principle to electrodeposit monatomic Si from a Si4+-containing compound melt. Moreover, because the carbon content of the high-purity Si obtained through electrolysis can be effectively controlled and used as a very ideal raw material in the preparation of electronic-grade and solar-grade Si, the preparation of high-purity Si through electrolysis has received widespread attention [8,9]. Monnier et al. [9] used a graphite electrode to obtain high-purity Si (99.9 %-99.99 %) from Si02/Na3AlF6 system through electrolysis; however, because the Si was precipitated in a solid form and showed poor conductivity, the deposition rate was too slow. Olsen et al. [10] obtained high-purity Si films via electrodeposition in K2SiF6/KF-LiF system by selecting electrode materials with high surface quality (such as Ag and graphite). However, in order to ensure the film quality, the deposition current density must be relatively low (10-50 mA/cm2), resulting in a low current efficiency and low deposition rate, which are not conducive to reducing energy consumption and applying to practical use"

Jan 1, 2014

By Renxing Li, Yongyong Gong, Yufeng Cheng, Zhenxing Yin, Xin Cao, Qijie Zhai

"The influence of electric current pulse (ECP) on the solidification structure of SUS430 ferritic stainless steel (FSS) was investigated in the current study. The technology of ECP has been widely used to improve the properties of metals with relatively low cost. The parallel electrodes were inserted into the free melt surface to constitute a current loop. The different influences of three parameters on solidification structure were studied by changing the peak current value, frequency and treating time respectively. The results indicated that the ECP significantly increased the number of equiaxed grains of SUS430 FSS. The as-cast structure without ECP treating was almost wholly columnar, while the number of equiaxed grains of the specimen, which was treated 3min with a peak current of 400kIA, increased to 2698 in the observed surface. To get the best refinement, an optimum range of these three parameters is required and the peak current value plays the most important role.IntroductionFor the lack of nickel resource and the pressure of environment protection, ferritic stainless steel is increasingly adopted to replace the austenite stainless steel because of its low nickel content and good mechanical properties. SUS430 steel is a typical example with excellent performance and relatively low price to replace the application of austenitic stainless steel[1-3]. This type of steel with high thermal conductivity coefficient, low expansion coefficient, good oxidation resistance, excellent stress corrosion resistance and other fantastic characteristics is often used to make components which need to have resistances for atmosphere, water, steam and oxidizing acid corrosion[4]. Since the developing of columnar grains and low toughness at high temperature, its products are easily crinkled and cracked during the subsequent rolling process[5]. The application of ferritic stainless steel is limited by these defects[6-8]."

Jan 1, 2012

By Emanuel Negrao Macedo, Edinaldo Cunha, Mauro Oliveira, Jose Antonio da Silva Souza

"This paper presents the study of the increasing addition influence of the bauxite waste in some properties of polymeric matrices composites reinforced with natural fiber: Curaua (Ananas Erectifolius smith). There were evaluated properties as density, tensile and flexural resistances. The high pH provided by the waste is used as hydrolysis agent, providing the pectin cement dissolution of the fiber bundles, and therefore, improving the mechanical adhesion in the fibermatrix interface and the increase of the fiber bundles aspect ratio. Furthermore, the content of silico-aluminous material in the waste provides increase in the composite abrasivity, which is destined to civil and naval construction. The fact of being a low-cost and highly available waste turns the red mud in a high potential material as polymeric composite filler.IntroductionRed mud is an insoluble residue, originated from the bauxite refining through the Bayer Process [1]. It is an Iron Oxide rich material [2] (substance responsible for the red brick color), it has a complex chemical composition [3], and its composition is highly dependent of the type of bauxite used in the process [4]. It has high alkalinity (pH= 10 - 12.5) and a very small solids size distribution (95% diameter< 44µm) [1], what turns the red mud a serious environmental pollutant.The utilization of fillers on composite materials is done after many necessities; however, one of the major necessities is the cost reduction [5]. Furthermore, mechanical and thermal properties of polymers usually are improved by the addition of inorganic fillers [6], being an example of this improvement the reduction of the flammability of polymer matrixes due to the addition of functional clays [7]. In this way, the red mud becomes potential filler for composites, since cheap and easily available fillers (like red mud) are a good option to reduce costs [8]."

Jan 1, 2013

By Emilia Visileanu, Eftalea Carpus

"The strategy of developing the Romanian textile industry sub-sectors envisages the achieving of certain superior production indices, from a physical and value point of view, in 2010, a quantitative increase of textile wastes by 14% in 2010 as compared to 2000, implicitly. The percentage of the turned-to-profit wastes will have an increasing tendency, from 53.6% in 2000 to 74.7% in 2010. The article synthetically presents the innovative elements of the technology of processing the industry textile wastes.1. Introduction“People will need to re-adopt this sense of rarity that has been forgotten over the last two centuries. Humans need to collect, sort, recover, going back to the old ideal of alchemists: complete the material cycle, turn waste into resource, reduce all forms of predatory behaviour as much as possible”Irrespective of the historical period, geographical positioning, economic power or employed technologies, wastes resulted and will result in a bigger or smaller quantity as long as life and activity on Earth go on. The negative effects of these over the environment factors and implicitly over population health are well known all over the world and not approaching this matter enough may have catastrophic consequences over life. Having in view these aspects, finding solutions for diminishing the general waste quantity and limiting the negative effects of those products is important, by effecting the reusing of the recyclable ones in the production processes as secondary raw materials, and by ecologically treating and storing those than cannot be reused.2. Experiments and researchesThe textile industry affects the environment by the high water, energy and chemical consumption, as well as by the high quantity of wastes that are the result of using an impressive number of chemical substances and technological processes.The development strategy of the Romanian textile industry sub-sectors foresees, for 2010, the achieving of certain higher production indices as compared to 2000, both in terms of materials (as merchandise) and in terms of value, which implicitly leads to a quantitative increase of wastes.The flexible, economic and ecologic technologies which include systems of waste preliminary preparing (cutting, opening) and conventional or non-conventional system of processing the recovered fibres lay at the basis of substantiating the activity of implementing the notion of zero wastes."

Jan 1, 2008

By Michael J. Mankosa

The increased emphasis placed on recycling of consumer and industrial waste products has generated a need for advanced separation techniques for recovery of valuable by-products. As a result, the metals recycling industry has made great strides in the recovery of used wire products through the application of chopping and screening processes. Unfortunately, in many instances, the final plastic reject still contains a substantial portion of valuable metal. Typically, this material has been discarded, since an appropriate separation technique has not been available. Recent work conducted by Carpco, Inc. in Jacksonville, Florida indicates that a high-grade metal and/or plastic product can be recovered from this waste material using a novel density separation process. Extensive test work has been conducted using this procedure to validate separation performance as well as equipment capacity. This paper will present the basic operating principle of the separator, as well as results from tests conducted using various feed materials.

Jan 1, 1995

By Roberto Parra

The selective reduction smelting of Cu2O in Cu2O-FeOx-SiO2 melts has been studied at laboratory level, using as a feed a dead roasted calcine from a copper concentrate. The purpose of the study was to evaluate the kinetic and mechanisms of the indirect reduction with CO and the direct reduction with graphite from 1260°C to 1350°C. The reduction rate by CO was found to be 10-2 to 10-1 mole Cu2O m-2s-1. The graphite reduction macrokinetics for FeO and. Fe2O3 containing melts, was found to be a first order reaction with respect to the Cu2O concentration, with a kinetic constant of 104 to 10-3 s-1. The reduction rate was not sensitive to temperature nor to stirring, in the range studied. The measured reduction rate is almost one order of magnitude larger than the observed rate for the direct reduction of FeO.

Jan 1, 1999

By Shadia J. Ikhmayies

"Cadmium sulfide (CdS) in the form of thin films is an interesting material because it has a large variety of applications ranging from photovoltaic to luminescent devices. N-type CdS is usually used as a window layer in the heterojunction CdS/CdTe thin film solar cells. A review of the photoluminescence (PL) spectra ofn-type CdS thin films prepared by different techniques was performed. The effects of different dopants and impurities and the effects of temperature and deposition parameters on the PL spectra were discussed. Annealing in different atmospheres causes the changes in material structure and phase change from cubic to hexagonal phase which can be detected through the variations in the PL spectra. CdCh heat treatment improves the cystallinity of the films and enhances the exciton peaks and the green band in the PL spectra.IntroductionThin CdS films deserve attention because their expected gap emission lies very close to the highest sensitivity of the human eye. Thus, one might assume that thin CdS films are an appealing host for photonic devices [ l]. They have been used in a lot of applications including electronic and optoelectronic devices [2]. Thin films ofn-type CdS are widely used as a window layer in heterojunction solar cells such as CdS/CdTe solar cells. Doped and undoped CdS thin films can be obtained by different techniques such as; spray pyrolysis (SP) [3], chemical bath deposition (CBD) [2, 4], pulsed laser deposition [5, 6, 7], laser ablation [l], thermal evaporation [8].Several experimental techniques have been used in order to study semiconductor defects. In particular, photoluminescence (PL) has been shown as a powerful and sensitive tool in examining the crystal quality of polycrystalline thin films. PL can be used in the detection of defects which are radiative active. These defects can also act as traps in the transport of carriers [9]. The photoluminescence (PL) of thin film CdS is strongly influenced by the unbalanced stoichiometry, which is typical for CdS and is in general evoked by a Cd surplus. With increasing Cd content, the emission spectra move far below the gap to the red spectral range. Besides stoichiometry problems, independent of the material deposited, the PL properties of thin films depend on surface features and the influence of the interface between the film material and the substrate [10]."

Jan 1, 2013

By Peng Peng, Ouo Cheng, Guodong Lai, Lijuan Chu, Zebiao Zhang

"The pressure acid leaching residue of zinc concentrate contains a large quantity of sulfur. The present study attempts to leach sulfur using a mixture of ammonium sulfide and water solution at 25°C. Effects of three leaching variables: ammonium sulfide concentration, leaching time, liquid/solid ratio on the sulfur leaching rate were investigated. The process conditions were optimized using response surface methodology based on the central composite design. From the analysis of variance (ANOVA), the significant factors on response were identified. The optimum conditions for leaching elemental sulfur from pressure acid leaching residue of zinc concentrate were obtained using an ammonium sulfide concentration of 2.5 mol/L, leaching liquid-solid ratio of 6.5:1 and leaching time of 7 min. Under the optimum experimental conditions, a maximum of 98.50% of total sulfur was extracted. The experimental results obtained agreed satisfactorily with the model predictions, with a correlation coefficient (R2) of 0.99.IntroductionSulfur is widely used in agriculture, medicine, rubber, building materials, gunpowder, wine and sugar, and other fields [1]. Currently the world sulfur production is 40Mt, out of which more than 90% is recovered from industrial processes, and 10% is natural [2], This highlights the importance of sulfur recovery. As the pressure leaching technologies [3] continue to mature and are increasingly applied to refining, a large quantity of high-sulfur residue is produced [4-5]. It is desirable to recover sulfur from this residue, so that it is economically advantageous, and reduces environmental pollution [6]."

Jan 1, 2012

By O. Chemezov, Yu Zaikov, A. Apisarov, A. Isakov

"Silicon deposits containing 99,9 wt.% of main component were obtained by SiO2 electrolysis from chloride-fluoride melts. The operating temperature was varied from 973 up to 1073 K. The conditions for obtaining crystalline fibrous micro- or nanodeposits were determined. The deposits were investigated by ESM methodIntroductionThere are large reserves of natural quartz of high purity in Russia. Processing of this raw material by electrolysis in molten salts produces silicon containing 99.9 weight percent of basic substance.[1]This method is less energy-consuming in comparison to existing methods for producing high purity silicon from gas phase.Another advantage of the electrolytic method for producing silicon from its oxide in molten salts is the possibility of production of high-purity silicon under air atmosphere. It dramatically reduces costs of the electrolytic cell construction, and the operating costs at electrolysis.On our opinion, the main advantage of the electrolytic production from SiO2 in molten salts is a unique opportunity to obtain micro-and nanostructures of silicon deposits. In particular, it is possible to obtain fibrous structures of silicon. The electrolytic method allows smoothly adjusting the thickness and length of silicon micro- and nano-wires by varying the cathode current density and temperature of the process."

Jan 1, 2012

By Leandro Voisin

A new pyrometallurgical treatment alternative is proposed for cleaning complex copper matte with high content of impurities in the copper smelting process, thus, in a suitable furnace, a given amount of pig iron will be added to the liquid complex matte with a matte grade between 65 and 75 % Cu under reducing condition and will produce three liquid phases of matte, copper-rich alloy and iron-rich alloy. Hence, in this study, firstly, a mass balance calculation was made on the basis of the reported data for the distribution ratios of the components among the three phases to define the optimum condition where most of the arsenic can be fixed in the less valuable liquid iron-rich alloy. By taking advantage of the high concentration of arsenic in the iron-rich alloy, the small volume alloy may be disposed in a yard, while the precious elements may be recovered effectively in the liquid copper-rich alloy and/or in the liquid matte. Secondly, laboratory-scale experiments were conducted to apply the proposed process to the matte produced from the slag-cleaning electrical furnace and the Teniente Converter of the Codelco-Norte smelter. The obtained results indicate that the proposed process for cleaning complex matte is promising.

Jan 1, 2006

By Mamoru Kuwabara

A high-power sound which can transmit through any continuous elastic medium with less attenuation, particularly in liquid allows us to externally control the system of concern by using the acoustic radiation force or the cavitation phenomena. These functions may eliminate gravitational and/or atmospheric constraints which are often encountered in conventional operations for producing clean and advanced materials. This paper outlines the recent development in the field of sonoprocessing of materials. Cold model experiments in some vessels have been performed to simulate ultrasonic operations such as inclusion removal from liquid, degassing of melt, emulsification of two liquid phases, solidification processing, and decomposition of chemical species in waste water. High speed visual imaging is carried out for better understanding of the cavitation phenomena as well as the followed microjets during the processing. The radiation force acting on fine suspending objects in a fluid can be utilized for eliminating or rearranging/orienting the objects in the fluid. Acoustically induced cavitation phenomena in liquid can be utilized as an effective dynamic means to control interfacial phenomena as well as micro- and macro-mixing of liquid. Sonochemical and thermal effects in cavitation multi-bubble can be also useful in a waste water treatment.

Jan 1, 2006

By K. Noda

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. is carrying out a low cost production using a Tamano Type Flash Smelting Furnace (T-FSF), which is an improved version of Outokumpu Type Flash Smelting Furnace but without slag cleaning furnace and also by developing its own coke combustion technology. Coke combustion technology that is the basis of the system has been improved several times and, at present, it has evolved to a stage where it can be reproduced on the Computer guided system for Coke Combustion in the T-FSF (CCCT) using a general- purpose computer. This CCCT is featured by &apos;its trend control and predicting function, and an operator can freely control the operation parameters so as to control the operation flexibly. We have recently developed an overall energy reduction system covering the Smelting Plant to Sulfuric Acid Plant, which we call an Optimum Low Cost Operation System (OLCO) to reconsider the energy costs including coke, heavy fuel oil, and electric power. In this report, we would like to present the recent operation of T-FSF based on CCCT as well as the optimum energy operation utilizing OLCO system.

Jan 1, 2002

By K. Hussin

Perlis is one of the major producers of ?Batu Reput? in Malaysia and majority of the deposits contain of high-purity calcium and magnesium carbonate. The composition of Batu Reput is similar with the ordinary dolomite. Currently, the ?Batu Reput? is used as filler in the road construction, however with this new invention, it can be value added and maximized its application in the daily life, for example as construction materials, decorative products, souvenir and etc. This paper presents the fabrication of Artificial Marble from ?Batu Reput? and in this case, it was used as filler in the matrix of epoxy which is acted as a binder.

Jan 1, 2006

By Mark E. Schlesinger

A substantial database exists for the thermodynamic properties of many antimonide compounds, but these have rarely been compiled or critically discussed. An abbreviated version of a full?scale review of the thermodynamic properties of binary antimonide compounds is presented, focusing on the choice of experimental techniques.

Jan 1, 2006

By Peng Fan

Liquid phase tends to migrate from an aggregate of solid particles immersed in a liquid phase into another aggregate composed of the same solid particles and liquid but with smaller particle sizes and/or lower volume fraction of the liquid phase. This type of liquid migration in a two phase system can be attributed to the driving force for the system to decrease its total interfacial energy. With liquid migration pressure as a convenient measure for the total interfacial energy of a solid-liquid two-phase system, liquid migration can be attributed to the existence of liquid migration pressure gradient in the two-phase system. The kinetics of liquid migration is of great practical importance for many industrial processes, one of which is the liquid phase sintering of functionally graded WC-Co composite materials. During liquid phase sintering, WC-Co composite forms a typical solid-liquid two-phase system where solid particles of WC are immersed in liquid Co. For a sample composed of two layers of WC-Co with the same Co content but different WC particle size, Co gradient will be formed during liquid phase sintering; while for a sample composed of two layers of WC-Co with the same WC particle size but different Co content, the Co gradient will be eliminated during liquid phase sintering. The formation and elimination of Co gradient are controlled by the liquid migration pressure gradient. This paper describes a numerical simulation of the kinetic process of the formation and elimination of cobalt gradient.

Jan 1, 2006

By Leizhang Gao, Zhengfeng Qu, Pingsheng Lai, Chenguang Bai, Meilong Hu

Since Fray-Farthing-Chen (FFC) Cambridge process was proposed in 2000 for electrochemical extraction of titanium from titanium oxide, a great quantity of research has been carried out to investigate the mechanism of the electro-reduction of the process. Results show that the intermediate products of perovskite phases are inevitable during the electro-deoxidation process. In this paper, a new perspective focus on the anodic behavior was applied. The behavior of the graphite anode with different times has been investigated. Although the main anodic process in the electrolysis is the oxygen evolution by means of the CO2. The interphases of calcium species appeared on the cathode are closely related with chlorine ions in the molten CaCl2. In addition, the released CO2 from the anode is related with the formation of CaCO3 which floated on the surface of the molten salt.

Mar 1, 2018

By Zhigang Liang

Effects of the configuration parameters of submerged entry nozzle on the flow field in slab mold were investigated through a water modeling. The experimental results showed, when the original submerged entry nozzle was applied, there was an appreciable level fluctuation in the mold with obviously naked surface and entrapment of mold flux at higher casting speed. By increasing the outlet area of submerged entry nozzle, without any change of other configuration parameters and submergence depth, a proper fluid field with active surface and good covering of mold flux can be obtained, which is proper to meet the requirement for increasing the casting speed and improving the slab quality simultaneously.

Jan 1, 2009

By Peter A. Spencer

Bacterial oxidation technology has the ability to selectively attack sulphide minerals. Selectivity allows oxidation of more reactive minerals and the extraction of valuable metals while leaving the bulk of the sulphide component unreacted. Partial oxidation can be used on arsenopyrite to recover gold and for the leaching of base metals, such as copper and nickel, from pyritic ore and concentrate without generation of large quantities of acidic iron solution, which must be neutralized. Thus, rejection of pyrite during the oxidation process can considerably reduce treatment costs. Acid generation in tailings dams would be minimal, compared with most Thiobacillus cultures, as the optimum growth temperature of Bactechts culture is above ambient.

Jan 1, 1992

By Minh H. Pham

This paper presents a technique for imaging the extent of solidification of molten metal flowing in a cooled pipe based on the concept of eddy currents. A 3D mathematical model, which relates the geometry of solidification to the scattered field induced in a solenoid external to the pipe, is derived. The model is described by a set of integral equations which are solved numerically using the moments method. An iterative algorithm is developed to reconstruct the solidification distribution image. Experimental measurements have shown that the eddy current technique is sufficiently sensitive for practical purposes.

Jan 1, 2001