Search Documents

By D. Gregurek

In non-ferrous metal furnaces the installed magnesia-chromite refractory lining is exposed to several stresses, rather complex in their interaction. Therefore, a detailed investigation and understanding of wear mechanisms through “post mortem studies” is an important prerequisite for refractory producer. Additionally, in order to determine the most suitable refractory products and to improve the lining life of refractories, practical corrosion testing with processing slags is performed. For this purpose the test-facilities, such as induction furnace, rotary kiln but also cup test and drip slag test, allow the best possible understanding of chemothermal brick wear on pilot scale. Prior to testing a complete mineralogical investigation, thermo-chemical calculation via FactSageTM of the slag was carried out. Based on such research results, combined with specific process knowledge RHI Magnesita can recommend appropriate brick lining solutions for non-ferrous metal furnaces.

By J. Gartelmann, B. Zaslavsky, Y. Vojta, D. J. Chaiko, W. Mego, A. N. Rollins

"Aqueous biphasic extraction (ABE) processes offer the potential for low-cost, highly selective separations. This countercurrent extraction technique involves selective partitioning of either dissolved solutes or ultrafine particulates between two immiscible aqueous phases. The extraction systems that we have studied are generated by combining an aqueous salt solution with an aqueous polymer solution.We have examined a wide range of applications for ABE, including the treatment of solid and liquid nuclear wastes, decontamination of soils, and processing of mineral ores. We have also conducted fundamental studies of solution microstructure using small angle neutron scattering (SANS). In this chapter we review the physicochemical fundamentals of aqueous biphase formation and discuss the development and scaleup of ABE processes for environmental remediation.IntroductionAqueous biphasic extraction (ABE) is a highly adaptable separation technique that can be used in a wide range of applications. We have been evaluating various types of ABE systems for possible applications in the treatment of solid radioactive wastes (1,2), liquid nuclear wastes (3,4), and contaminated soils (5-7), and in the removal of organics from aqueous salt solutions (8). We have also conducted fundamental studies of the solution microstructure of ABE systems using small angle neutron scattering (SANS) (9).The extraction systems are generated by combining an aqueous salt solution and an aqueous polymer solution. This produces two distinct liquid layers that are as immiscible as oil and water, yet each liquid layer contains at least 70 to 80 wt % water. The biphasic systems that we have been working with consist of immiscible polyethylene glycol (PEG) and salt solutions. Some inorganic salts that promote biphase formation with PEG solutions include the sodium/potassium salts of sulfate, carbonate, phosphate, and hydroxide (10)."

Jan 1, 1996

By James R. Craig

The slags generated during gasification of petroleum coke are heterogeneous and con-sist of many different phases. These phases are important because their physical properties affect the operability of gasifiers and because they concentrate many elements that are present in the petroleum coke feed in only minor to trace quantities. An understanding of the chemistry and physical nature of these slag phases is necessary to predict behavior in the gasifier and in considering the ultimate use or disposal of the materials. Slags typically consist of silicate glasses, calcium-silicates, free iron-nickel metallic phases, iron sulfides, and aluminum oxide spinels enriched in iron, chromium, and vanadium. The partitioning of elements among these phases has been analyzed and will be discussed.

Jan 1, 1989

By Ernie M. Crist, Laurentiu Nastac, Frank Spadafora

"This paper describes the modeling techniques and the experimental and computer results for two casting processes that are under development and optimization. These processes are described as follows:1) Electromagnetic stirring (EMS) during casting of Ti-6Al-4V round ingots using the plasma arc cold hearth melting (PAM) process: The purpose of EMS is to establish a singlemelt PAM process capable of consistently producing as-cast ingots without helium porosity and also having no need for surface conditioning prior to secondary processing.. The modeling approach is based on the numerical solution of Maxwell's equations, fluid flow, and heat transfer equations, and mesoscopic modeling of the grain structure.2) Casting of Ti-6Al-4V slabs using the single-melt PAM process: The purpose of slab casting is to improve yield by eliminating an intermediate blooming step for converting round ingots to slabs. The modeling approach is based on the numerical solution of fluid flow and heat transfer equations. The effects of pouring and mold temperatures on the pool and temperature profiles were studied. Also, the torch effects (such as the torch standoff and its traversing path) on the pool and temperature profiles were investigated and the best-case scenario was used in the experiments. Evaluation results at RMI Titanium Company showed that the plates made from the slabs met the mechanical properties and microstructure requirements.Acknowledgment. This work was conducted by the National Center for Excellence in Metalworking Technology (NCEMT) operated by Concurrent Technologies Corporation (CTC) under contract No. N00014-00-C-0544 to the US. Navy as part of the US. Navy Manufacturing Technology Program. Dr. K. b. Yu from RMI and my colleagues from CTC are acknowledged for their comments on this work."

Jan 1, 2004

By Shaik Jeelani, Esperidiana A. B. Moura, Vijaya K. Rangari, Roberta A. Lima, Rene R. Oliveira

This work present the preparation and characterization of biodegradable nanocomposites based on aliphatic-aromatic copolyester (PBAT)/polylatic acid (PLA) blend reinforced by TiO2 nanoparticle. The biodegradable polymeric nanocomposites were prepared by melting extrusion process using a twin-screw extruder machine. The influence of the TiO2 nanoparticle addition on mechanical and thermal properties of PBAT/PLA blend was investigated by tensile and impact tests, SEM, DSC and XRD analysis and the correlation between properties was discussed.

Jan 1, 2015

By T. K. Mukherjee, C. K. Gupta

"The importance of the processing of secondary resources such as solid industrial wastes and liquid effluents as well as byroducts for the recovery of the associated metal values hardly needs any elaboration. Such processing contributes in no small measure towards the augmentation of the availability and the supply position of resources. As an added benefit, it leads to a reduction in environmental pollution caused by the undesirable waste materials. As some typical examples of secondary resources in the Indian scenario, mention can be made of spent catalysts, metal/alloy scrap, ash, consumed batteries, flue dust, slag, sludge and slime, pickling solutions, spent acids, plating rinse solutions, spent etchants, waste water from synthetic fibre manufacture and from tanneries etc .. These wastes constitute a source of a variety of non ferrous metals. In the processing of secondary resources like these, the techniques of hydrometallurgy such as solvent extraction playa pivotal role.This paper outlines the efforts made to use solvent extraction to recover (1) base metals such as copper, zinc, nickel and cobalt from a number of secondary resources like cake, and sludge (2) refractory metals like molybdenum and vanadium from sulphidic byproducts and spent catalyst and (3) nuclear metal like uranium from phosphoric acid. In the case of base metals, process flowsheet involving the use of acidic extractants such as DEHPA and PC88A have been optimised. The problem of iron removal from the leach liquor, which influences the metal recovery process significantly, has drawn a special emphasis. In the case of refractory metals, basic extractants like Alarnine 336 has been pressed into service to produce kilogramme quantities of pure salts of molybdenum and vanadium. Finally, the paper gives a brief account of plant experience in recovering uranium from phosphoric acid, using a solvent system comosed of DEHPA and TOPO."

Jan 1, 1996

By T. K. Mukherjee

The importance of the processing of secondary resources such as solid industrial wastes and liquid effuents as well as byroducts for the recovery of the associated metal values hardly needs any elaboration. Such processing contributes in no small measure.towards the augmentation of the availability and the supply position of resources. As an added benefit, it leads to a reduction in environmental pollution caused by the undesirable waste materials. As some typical examples of secondary resources in the Indian scenario, mention' can be made of spent catalysts, metal/alloy scrap, ash, consumed batteries, flue dust, slag, sludge and slime, pickling solutions, spent acids; plating rinse solutions, spent etchants, waste water from synthetic fibre manufacture and from tanneries etc. These wastes constitute a source of a variety of non ferrous metals. In the processing of secondary resources like these, the techniques of hydrometallurgy such as solvent extraction play a pivotal role. This paper outlines the efforts made to use solvent extraction to recover (1) base metals such as copper, zinc, nickel and cobalt from a number of secondary resources like cake, and sludge(2) refractory metals like molybdenum and vanadium from sulphidic, byproducts and spent catalyst and (3:) nuclear metal like uranium from phosphoric acid. In the case of base metals, process flowsheet involving the use of acidic extractants such as DEHPA and PC88A have been optimised. The problem of iron removal from the leach liquor, "which influences the metal recovery process significantly, has drawn a special emphasis. hi the case of refractory metals, basic extractants .like Alamine 336 has been pressed into service to produce kilogramme. quantities of pure salts of molybdenum and vanadium, Finally, the paper gives a brief account of plant experience in recovering uranium from phosphoric acid, using 'a solvent system comosed of DEHPA and TOPO.

Jan 1, 1996

By Toshiyuki Kawai

Copper concentrate smelting directly in P-S converters was started at Onahama Smelter in 1983. Thereafter, the tonnage of concentrate smelted through the P-S converters increased, such that by 2002, it equaled the tonnage smelted through the reverberatory furnaces. In 2003, 56% of the total copper concentrates treated at Onahama Smelter were processed directly through the P-S converters. Technical improvements are reviewed and advantages of direct smelting in P-S converters are reported.

Jan 1, 2005

By Christina Viklund-White

Life Cycle Assessment has been used to compare the environmental performance of landfilling versus recycling of the zinc used for galvanizing steel. Hypothetical process routes were com-posed involving four different EAF dust treatment processes; Waelz kiln, DC-furnace, EZINEX and slag fuming, as well as scrap dezincing. The study shows that recycling of zinc used for galvanizing steel has environmental benefits in that it saves zinc resources. However, zinc recovery does not necessarily decrease the potential impact on global warming and acidification. The magnitude of these two impact categories is tightly correlated with the amount and type of primary energy consumed in a process. Due to the high electricity consumption in the dezincing process, this route has the highest impact on Global Warming Potential as well as Acidification Potential. The major part of the energy requirement for the production of zinc from primary and secondary sources is consumed in the reduction of ZnO to Zn. The consequence is that the theoretically possible savings in primary energy by recycling zinc-containing materials are relatively minor. The impact categories "land use" and "waste generation" are not considered in this study, but most likely the evaluation of such impacts would further increase the potential environmental impact of the landfill alternative. The results also show that the location of an electricity-intensive process highly affects the potential environmental impact. Comparing process and material alternatives in LCA studies where branch average data is used, is considerably more complex than when LCA is used within a company.

Jan 1, 2000

By Maneesh Singh

During the various stages of iron & steel production a number of iron-rich by-products are generated. The traditional way to recycle them back to the blast furnace has been the balling - sintering process. These by-products can also be made into cement-bonded agglomerates for use as burden material for blast furnaces. In order to improve the quality of agglomerates the effects of various processing parameters on the properties of cement-bonded briquettes have to be controlled. This paper looks into the various aspects of producing cement-bonded agglomerates and using them as burden material for blast furnaces.

Jan 1, 2003

By Vinay Kumar

The disposal of large quantities of electronic scraps generated world wide is causing not only environmental problem but also loss of resources. Therefore, R & D efforts have been made to develop a suitable process for extraction and separation of metals viz. copper, zinc, cadmium and nickel expected from the leaching of e-scraps using solvent extraction process. Different process parameters viz. pH, aqueous to organic ratio, kinetics of extraction, extraction isotherm to establish stage requirement for extraction in continuous mode etc have been studied to optimise the condition for the separation of metals. The studies showed the selective extraction of copper after iron precipitation from the sulfuric acid leach solution of e- wastes containing ~1.0 g/L Cu and minor impurities with 2-hydroxy-5- nonylacetophenoneoxime (LIX 84) above pH 2.0 in single stage. A scheme for separation of cadmium, zinc and nickel has been proposed using di(2-ethylhexyl) phosphoric acid (D2EHPA) under controlled pH of the aqueous solution. The order of extraction was found to be Zn> Cd> Ni.

Jan 1, 2009

By Shadia Ikhmayies

ZnO microprisms in thin film form were produced by the low cost spray pyrolysis technique at a substrate temperature of 350 ± 5 °C on glass substrates. Scanning electron microscopy (SEM) and energy dispersion X-ray spectroscopy (EDS) were used to explore morphology and composition of the films respectively. The films were found to be oxygen rich and contain chlorine. ImageJ software was used to analyze the size of the prisms, where the diameter and length of the microprisms were estimated.

Mar 1, 2017

By Ludovic Charpentier

Production of metallic wires directly from liquid jets would avoid drawbacks of extrusion (space needed, damaging, cost?) and enable recycling. But liquid jets tend to break, due to capillary instabilities, unless a solid layer (coating or start of solidification) surrounds it. We recently developed a process to produce tin wires, cooled by water flow parallel to the jet. Superficial oxidization of tin produces a glass coating around the jet. Studies showed the length of wires increased when increasing speed of tin jets, and that water average speed should be the closest possible to the jet one to have smooth fibers. Producing 1 mm diameter wires is possible. The length of wires is limited by the experimental setup, which does not provide possibilities to coil the wire. Most of other metals do not generate glass-like oxides. The lack of coatings makes it necessary to reduce the capillary instabilities to obtain fibers.

Jan 1, 2006

By Dale T. Peters

In the United States, the United Kingdom and numerous other countries, copper has long been the plumbing material of choice. This has been the case since the late 1920s in the United States and since World War II in the United Kingdom. However, in recent years the plumbing tube market has caught the eye of the chemical industry, and several plastic resins have been introduced to the marketplace as substitutes for copper in household plumbing systems. One of these, polybutylene tube, had so many failures in the United States that a class action law suit was filed, and the manufactures of this product were forced to create a trust fund of nearly one billion dollars to repair damages caused by their product. Chlorinated polyvinylchloride (CPVC), in rigid pipe form, on the other hand, has been mechanically acceptable albeit its recent introduction precludes the test of time enjoyed by copper tube in this application. This paper reviews the State of California's portrayal of copper's environmental effects and will be largely based on the data and information assembled by the Copper Development Association Inc. in its presentation to the State of California in August, 1998 in response to the State's Draft Environmental Impact Report for Chlorinated Polyvinyl Chloride (CVPC) Pipe for Use for Potable Water Piping in Residential Buildings. The paper is intended for use as a model for the use of other copper organizations and individuals in responding to similar situations.

Jan 1, 1999

By William J. Mallio

Substantial differences between in situ and conventional technology require that in situ ore grade be established for deposit as distinct from the total contained metal value. Establishing an in situ ore grade involves determining the fraction' of the contained metal that can be leached by the fluid. This depends on the proportion of the ore minerals that occur on fluid flow paths as defined by the permeability distribution. Mechanisms involved in the in situ mining of sulfides are: oxidation of the sulfur, solution of the metals, complexing of the released metals, and a transport to a recovery point. Metal ions may be delayed or lost due to inefficiencies in these pro-cess steps or by reactions of the metal ions in solution with the rock. These reactions can involve precipitation of new phases, exchange of the metals of the interest with Ca or Na in clays or zeolites, retention of metals in oxidized mineral grains, or secondary enrichment of other sulfides along the paths of the solution flow. The efficiency of solution of metals and potential loss or delay mechanisms are controlled by local equilibria (the Eh, pH conditions) present in different parts of the ore zone. Permeability distribution in the rock mass and the coincidence of ore minerais with flow channels must be determined before a deposit can be judged suitable for in situ mining. Laboratory studies indicate that the natural permeability system is dependent on the degree of cementation of veins by late generation hydrothermal activities. The major conclusions of the study are:, 1. Deposit selection is critical; suitable deposit types include deep lying sedimentary deposits, selected zones of porphyry systems and vein controlled hydrothermal deposits; 2. Adequate laboratory and geochemical analyses should be undertaken through quantitative petrographic study and permeability mapping; and 3. Economic incentives for in situ mining must consider limitations of recovery caused by inefficiencies in dissolution and transport associated with particular deposits.

Jan 1, 1981

By J. R. Bhamidipati, Nagy EI-Kaddah

"Over the years, mathematical modeling has been established as a viable tool for design and analysis of melting and solidification processes. Modeling of electromagnetic casting and melting systems involves three coupled problems -- determination of the containment field, the shape of the meniscus, and the temperature field -- which have to be solved simultaneously. One of the difficulties in numerical simulation of these systems is in defining and gridding the solution domain as the meniscus shape of the liquid region is not known a priori. This paper describes a methodology for solving these coupled problems in a two-dimensional electromagnetic containment field. This method is based on the solution of the electromagnetic, free surface dynamic, and heat transfer equations in a fixed domain in computational space by mapping the physical space into an invariant computational space during the search for the equilibrium shape using a variable non-orthogonal coordinate transformation. This approach, also, eliminates the need for regridding the liquid and solid regions during phase change. This methodology is demonstrated for two electromagnetic confinement systems -- the Magnetic Suspension Melting process and the electromagnetic casting of aluminum. The model predictions are in good agreement with available data for these systems. It is suggested that the methodology presented here is likely to provide a useful tool in the design, analysis, and optimization of electromagnetic confinement systems. IntroductionDuring the past decade, mathematical modeling has emerged as a viable tool for the design, analysis, and optimization of casting and melting processes /1-2/. It is generally recognized that the usefulness of modeling to study the interplay between the various process parameters without resorting to extensive experimentation relies heavily on accurate representation of the physical phenomena in these systems. In modeling electromagnetic confinement casting and melting systems, it is important that the model address all aspects of electromagnetic field interaction with the metal, if accurate predictions are to be obtained /3/. The electromagnetic field affects the heat transfer phenomena primarily through joule heating. In addition, the electromagnetic forces play a key role in heat redistribution in the molten pool via melt stirring, and, in confinement systems, support the molten metal pool."

Jan 1, 1994

By Fumitaka Tsukihashi

Increasing amounts of steel scrap are being used as resources for steelmaking. Therefore. there has been a growing interest in the removal of handful tramp elements such as antimony, zinc, tin, arsenic, bismuth, lead and copper from the molten steel. The problem that should be solved is the economic removal treatment of residual tramp elements in the steelmaking processes and the production of high quality steel by reducing the effect of the contaminated tramp clements and satisfying the environmental regulations. In this paper, the available thennodynamic data of the residual tramp elements in the molten steel are summarized and the possibility of the removal of residual tramp elements from the molten steel is thcnnodynamieally estimated.

Jan 1, 2003

By Robert C. Laudon

Spectral reflectance data for 335 minerals, including 228 minimum-maximum combinations for anisotropic minerals giving a total of 563 data sets, have been collected from the literature and combined into a single database. Quantitative color values for x, y, Y, Ad , and Pe referred to ICI standard i11uminant C have been calculated from the spectral reflectance data and are included in the database. The programs plot spectral reflectance curves together with all quantitative color data for each mineral in the database. The plots and data can be directed to a dot-matrix printer such that a databook of quantitative color and spectral reflectance having one mineral per page can be generated for the ore microscopy laboratory. In addition, by sorting the database and grouping the minerals, groups or individual minerals can be plotted on the chromaticity diagram, and this plot can also be sent to a dot-matrix printer. The programs are written in compiled BASICA for an IBM-PC with graphics capabilities and at least 128KB random access memory (RAM). The databases are accessible either through the BASIC programs or through any commercial database system capable of loading and writing to an ASCII format sequential file. The programs and database are available by sending a blank diskette and self addressed, stamped envelope to the authors.

Jan 1, 1987

By S. Rick Gilbert

In the course of producing a final metal product, smelters, refineries, and other metallurgical facilities produce wastes which often come under the ?scrutiny of Federal and state regulatory agencies. Many of these wastes contain combinations on zinc, copper, lead, cadmium, nickel or other metals. Frequently in the form of reverts, dusts, or sludges, these metal-containing wastes are often buried in a landfill or speculatively accumulated for future action. Environmental liability can be reduced in many cases by selecting,-a recycling facility which can re-process the waste for.' metal recovery. Encycle, at its hydrometallurgical facility Corpus Christi, has Successfully processed a variety of metallurgical by-products and wastes and returned those contained metals to commerce.

Jan 1, 1995

By G. Bjorling

After complete dissolution of chalcopyrite concentrate in sulphuric acid in presence of nitric acid the excess of the latter is expelled by a surplus of concentrate and the last traces of nitrate removed in the mother liquor after crystallization of the copper and iron sulphates. Zinc accumulates in the mother liquor from which it can be removed by solvent extraction of zinc sulphate as a pair of ions. After dissolution of the sulphate crystals in water the neutral solution is oxidized in an autoclave at 140°C where iron sulphate is thermally hydrolyzed; the iron-free solution is taken to copper electrowinning and the cell acid after partial evaporation recirculated with the mother liquor to the leaching circuit. Total recovery of copper is about 96%; other metals like zinc and iron are concentrated in industrially usable products. At a copper price of about 70 c/lb, the method appears to be profitable also in a small unit.

Jan 1, 1976