Search Documents

By Gus Van Weert

The cost of oxygen is a major and common factor in the hydrometallurgical processes developed or proposed tor the oxidation of refractory pyrites. This cost involves charges for the generation and the transfer of the 02 to the mineral slurry. Bio-oxidation faces considerable design demands which require large scale equipment to be resolved. Nitric acid assisted oxidation offers low cost oxygen units; this method of pyrite oxidation deserves a closer look for large scale plants treating pyritic gold ores and concentrates.

Jan 1, 1990

By Jiangtao Li, Zhongwei Zhao, Xingyu Chen, Xuheng Liu

In tungsten ion-exchange process, excessive sodium impurity enters into ammonium tungstate solution. However, the Na content of the final ammonium paratungstate (APT) product must be strictly controlled. Consequently, it is necessary to remove Na from the ammonium tungstate solution during processing in order to obtain the required purity of APT. In this study, porous Na specific absorbent, Na1+xAlxTi2−x(PO4)3, is used to remove Na from the ammonium tungstate solution. Through experiments, the effect of reagent concentration of Na1+xAlxTi2−x(PO4)3, reaction time, reaction temperature and Na concentration on the Na removal were investigated. The results showed that under optimal reaction conditions of reagent amount of NATP 1.0 times of theoretical amount, reaction temperature 25 °C and reaction time 15 min, the Na removal from commercial (NH4)2WO4 solution can reach 98%. Na1+xAlxTi2−x(PO4)3 has a good applicability to different Na+ concentrations. The obtained APT product reaches the national standard purity of zero level.

Jan 1, 2014

By Patricio F. Mendez

This paper presents a formalism to automate portions of the traditional scaling procedure. This formalism, called here Order of Magnitude Scaling (OMS), captures essential components of the governing equations into a set of matrices and arrays amenable to computer implementation using standard linear algebra tools. This approach is valid and specially useful for large systems of multicoupled equations. The matrix approach proposed enables one to automate operations such as normalization, dominant balance, obtention of characteristic values, and check for self-consistency. Also, automation permits an exhaustive exploration of all possible balances and the discovery of unsuspected scaling laws. As an example, OMS is applied to the analysis of the viscous boundary layer with no external pressure gradient. The obtained scaling laws for boundary layer thickness and transverse velocity are the same as those obtained with traditional scaling, and in addition, a meaningful estimation for pressure variations within the boundary layer is obtained; this last estimation is typically not addressed in the manual analysis.

Jan 1, 2006

By H. Y. Sohn, M. Y. Mohassab-Ahmed

"As part of research to develop a novel flash ironmaking process using reduction of iron ore concentrate by natural gas or hydrogen, sulfur and phosphorus distribution ratios between MgOsaturated slag and iron were determined in the temperature range 1550-1650°C under three different gas atmospheres: H2/H2O, H2/H2O/CO/CO2, and CO/CO2. The distribution coefficients of sulfur (Ls) were 4.0, 2.0, and 0.8, respectively, under these atmospheres. The distribution coefficients of phosphorus (Lp) were, respectively, 8, 17, and 20 under these atmospheres. In the flash process over -25 wt% P and S volatilize during ore concentrate downward flight in the reactor shaft in addition to avoiding coke. Therefore, iron produced by the flash ironmaking process would have much lower sulfur contents than the typical hot metal produced by the BF.IntroductionGiven the issues related to large carbon dioxide emissions and energy consumption in the existing ironmaking technologies, a novel flash ironmaking technology was conceived by Sohn [1-3] at the University of Utah. This technology is the first ironmaking process that will convert iron ore concentrate directly to metallic iron in-flight. This process will produce iron directly from concentrate without requiring pelletization or sintering and avoid the need for coke. In addition, this process concept takes full advantage of the fine particle size of concentrate with a large surface area, which permits rapid reduction by a gas. In this novel ironmaking process, potential reductants and fuels are H2, natural gas, and coal gas. Therefore, an iron-slag bath is expected to be at equilibrium with gas atmospheres of mainly H2/H2O or CO/CO2/H2/H2O, respectively, corresponding to the use of H2 or natural gas/coal gas. Since the effects of an H2O- containing atmosphere on slag properties have not been studied before, it is critical for the development of the novel flash process to determine these effects. In H2-H2O-CO-CO2 gas mixtures under ironmaking conditions, H20 was found to have the most pronounced effect on the slag chemistry [ 4, 5]. In addition, it was found in this laboratory that water in the gas atmosphere affected the distribution of Mn between slag and molten iron [6]. Most previous work used CO/CO2 gas mixture to control oxygen partial pressure (p02) [7, 8]. Others used only inert atmospheres [9], although Kor and Richardson [10] used a mixture of C02/H2 to control p02. For phosphorus, previous research focused on Ar [11], Ar-CO mixture [12], CO [13], CO/CO2 [14] or N2/CO [15]. Therefore, it was necessary to investigate the effect of water vapor content in H2-H2O-CO-CO2 mixtures on the equilibrium distribution of sulfur and phosphorus between CaO-MgOsatSiO2-Al2O3-FeO- MnO (0.2-0.8 wt%)-P2O5 (0.1-0.9 wt%) slag and molten iron as part of the development of the novel flash ironmaking technology."

Jan 1, 2014

By Zengjie Wang

Kinetic study of hydrochloric acid leaching of Panzhihua ilmenite from China is presented. Both temperature and concentration of hydrochloric acid have significant effects on the rate process of Fe dissolution from ilmenite ore, while the ratio of liquid to solid has little effect on the Fe dissolution. The Fe dissolution is found to follow the spherical model f (??) =1-(1- ??)1/3 and the apparent activation energy is calculated as 47.21 KJ/mol, suggesting a chemical reaction controlled mechanism. The dissolving behaviors vary at different kinetic stages. At the beginning the amount of the dissolved Fe and Ti increased monotonically with leaching time, while about 15 minutes later the dissolved Ti in the form of TiOCl2 began hydrolyzed into TiO2 fines reunited on the ilmenite ore surface, as observed by SEM and EDS technique. For the unreacted ilmenite particles covered by a layer of hydrolyzed TiO2, the leaching seemed to be as a selective leaching of iron and because Ti dissolved from and hydrolyzed rapidly again into the unreacted ilmenite particles. The leaching process can be ended 4 hour later when almost of Fe has dissolved into the solution and TiO2 remains as solid residues. The effects of acid concentration and leaching temperature were also investigated.

Jan 1, 2009

By Achilles J. B. Dutra, Carlos M. Juarez

"The use of thiourea as a gold leaching reagent has been extensively studied by many researchers, and it has proved to be promising for some cases as refractory ores. Otherwise, the recovery of gold from these solutions did not receive so much attention. In this paper the electrowinning of gold in acidic thiourea solutions was studied by voltarnmetry and chronopotentiometry. An adsorption step was detected prior to Au(I) reduction and the diffusion coefficients at 25°C for Au-TU complex and FD were found to be 1.00 x 10.5 cm2 S-I and 1.98 x 10-5 cm2 S-I respectively. At -0.350 V (SCE) a passivation probably due to TU adsorption was observed. For higher overpotentials hydrogen evolution was the main reaction.IntroductionThe use of acidic thiourea solutions for the extraction of gold and silver has shown to be a promising alternative to the traditional process of cyanidation, specially for certain refractory ores (1-3) and electronic scrap (4). In some cases, the industrial scale was reached (1,5). The thiourea leaching of precious metals presents advantages over cyanidation, as faster kinetics, lower toxicity and lower sensibility to base metals; however the costs due to high thiourea consumption impairs its use.The majority of the publications on thiourea processing of gold is on leaching. Many are review papers (5-7). Recently, the adsorption and desorption of the gold-thiourea complex on activated carbon and ion exchange resins have been studied (8-11).Little research has been done on the electrowinning of gold from acidic thiourea solutions, most of it has been carried on the seventies and beginning of the eighties in the former USSR (12-17) and concerned the eletrolytic extraction of gold in tridimensional cathode cells.The present paper concerns the cathodic behavior of the gold-thiourea complex in the presence of formamidine disulfide in order to provide information on the electrowinning of gold from solutions obtained directly from leaching or from an elution process."

Jan 1, 1997

By Xiaojian Zuo, Yihua Han, Qingguo Xue, Jingsong Wang, Lintao Wang, Rongzong Lan

"Using the facility of reduction experiment, the low temperature reduction pulverization and reduction behavior of sinter in oxygen blast furnace (OBF) were studied. Through analyzing the results, the difference of pulverization and reduction behavior of sinter in OBF and conventional blast furnace (BF) were discussed. Furthermore, the effect laws of reduction temperature and the content of CO and H2 on reduction behavior of sinter were studied. Also the controlling step of iron oxide reduction was discussed. Compared with BF, the low temperature reduction pulverization of sinter became serious at 773 K; reduction rate became faster at 1173 K; reduction time became less and final reduction degree was increased in OBF. With increasing of H2 and CO contents, the reduction of sinter was promoted. The reduction process was controlled by interface chemical reaction at the earlier stage and by interface chemical reaction and internal diffusion at the final stage.IntroductionThe new ironmaking technology of Oxygen Blast Furnace (OBF) is most likely to be used in large-scale application process. The concept relies on the removal of the CO2 contained in the top gas of the blast furnace. Therefore the useful components, i.e. CO+H2, can be recycled back into the furnace and reused as reducing agents. In addition, injecting oxygen (O2) into the furnace instead of preheated air, removes unwanted nitrogen (N2) from the gas. Under the pressure of CO2 emissions in iron and steel making, the growing international shortage of coking coal resources and the rising price of coke, OBF has attracted attentions of both domestic and foreign researchers, because it has so many advantages such as high productivity, high PCI rate, low coke rate, high gas reducing capability and high top gas calorific value, etc [1-7]. As a result of recycling most of the top gas after CO2 removal and injecting oxygen into the furnace, the reduction capacity of blast furnace gas will be increased, so the metallurgical behavior of OBF's iron burden is different from traditional blast furnace. Therefore, it is one of the keys to develop this technology, which studies the metallurgical behavior of sinter in OBF. The purpose of this paper is to study the low temperature reduction pulverization and reduction behavior of sinter at the atmosphere of OBF, which includes the difference of low temperature reduction pulverization and reduction behavior of sinter in oxygen blast furnace and conventional Blast Furnace (BF). It will provide theoretical basis for the development of OBF."

Jan 1, 2012

By G. B. Harris

Much has been written over the past decade concerning the disposal of arsenic from metallurgical processes. In Canada, there are proposed regulations which would classify arsenic in the Primary Group of twenty one persistent, toxic pollutants to be banned or phased out. Since many nickel and cobalt ores, not to mention those of copper, gold and uranium, contain significant amounts of arsenic, it is pertinent to assess the current state-of-the-art of its disposal. The literature is reviewed, and it is demonstrated that from a purely chemical point of view, the family of ferric arsenates largely immobilize arsenic. There is clear evidence from laboratory studies that both crystalline ferric arsenate (scorodite) and amorphous ferric arsenates in which the molar Fe/As ratio is at least three (Fe/As = 3) have very low arsenic solubility; plant data are given to support this. The debate over the long term stability of these compounds continues however; the evidence presented for long term stability and for compound breakdown is critically reviewed in the light? of the recent structural studies, and the role of base metals in these compounds evaluated. Finally, conclusions are drawn as to the viability of a purely chemical process for the long term disposal of arsenic from metallurgical processes.

Jan 1, 1993

By Nagahiro Saito, Takahiro Ishizaki, Mituhito Hirota, Akio Fuwa

"Owing to their extremely high toxicity in the environment, the dioxins have been attracting social, technical and scientific attention in recent years. The authors theoretically had predicted the thermodynamic properties of all the dioxins via quantum chemistry and statistical thermodynamics and elucidated the generation-decomposition behavior of dioxins in the equilibrium calculation· of C-H-0-Cl system. In actual combustion processes, it is said that metallic compounds have much influences on the dioxins behavior. The aim of this study is to reveal the roles of metallic compounds the generation-decomposition behavior of dioxins is revealed from the viewpoints of quantum chemistry. Especially, the catalytic effect of copper has been investigated for the reaction, 2HCl(g)--H2(g}+Cl2(g) and for the etherification reaction from precursors, which is Phenol(g) here, to dioxins. The catalytic role of Cu is shown to have much influence on the generation -decomposition of dioxins.1. IntroductionIt is well known that dioxins are very harmful not only for our health but also for that of our children and grandchildren because they are very stable substance and their reaction rates of decomposition are considerably low. On the other hands, it is not well know how dioxins are generated and decomposed; the generation-decomposition conditions and paths as well as the catalysts to decompose them'1l. The authors believe that the thermodynamic and kinetic study of dioxins is useful to find a solution to these issuers. The authors have been investigating the following problems to reveal the generation-decomposition behavior of dioxins; (a) the prediction of the thermodynamic parameters of dioxins (2), (3), (b) the generation -decomposition behavior of non-chlorinated dioxins by the thermodynamic equilibrium calculations in C-H-O system(4) and (c) the generation-decomposition behavior of dioxins by the thermodynamic equilibrium calculations in C-H-O-CI system(5). Summaries of these thermodynamic researches are as follows.(I) The thermodynamic parameters for dioxins, which had been unknown and/or inaccurate'6 l, could be predicted and are available within the scientific accuracy."

Jan 1, 2000

By Batric Pesic

Dissolution of gold with elemental bromine was studied by using a rotating disc technique. The main parameters studied were: bromine concentration, stirring speed, pH, and temperature. Additionally, effect of copper, iron, and manganese was also examined. A special attention was paid to elucidate the role of cations, primarily Na+, during gold dissolution. It was found that gold dissolution with bromine was characterized with two pH regions. Below pH=7, gold dissolution was independent of pH, and above this value, gold dissolution decreased with pH increase. Gold dissolution rates were proportional with concentration of bromine. Two regions, diffusional and kinetic, were observed with respect to stirring speed. with respect to the role of Na+, and cations in general, they play absolutely no role during gold dissolution with bromine, unless they are in their lower oxidation state and become oxidized by bromine. In that case they have a negative effect because of bromine consumption.

Jan 1, 1991

By John Fallavollita

Conventional gas atomization produces powders that vary widely in size distributions and microstructures, thus making it very costly to produce powders tailor made in a narrow size distribution and microstructure. Furthermore, it is difficult to determine the relationships between atomizer operating conditions and resulting powder characteristics. The Impulse Atomization Process (IAP) was developed at the Advanced Materials and Processing Laboratory to produce powders with narrow size distributions. Powders produced by the IAP were reproducible and their sizes could be easily controlled by adjusting experimental conditions. Characteristics of Zn, Sn-Pb, AI-Cu, and Cu powders will be described to illustrate the flexibility of the process to tailor-make powders.

Jan 1, 1994

By Yuanbo Zhang, Guanghui Li, Zhenyu Fan, Tao Jiang, Xiaohui Fan

"Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60% of the total. Aiming at the features of sintering flue gases and existing problems during the flue gas desulphurization, a technical route of flue gas circulation sintering (FGCS) for iron ores has been put forward. Under the simulated experimental conditions, effects of FGCS process on the main output and quality indexes and SO2 emission rule are researched using simulating flue gases. Compared the novel FGCS with conventional sintering process, SO2 in the final sintering flue gas is obviously enriched and the total exhaust gases can be reduced evidently. The decreasing of oxygen content in circulating gases has bad effect on the sintering indexes. Increasing the oxygen potential is beneficial to obtain high quality sinters. This investigation shows that the FGCS process is promising.IntroductionSteel is a kind of essential material for modern society, but steel-making process is characterized by high energy-consumption and emission as well as heavy environmental pollution. Chinese steel industry has developed rapidly in the last decade, and the environmental problem caused by ironmaking and steelmaking have also aroused the greatest concern, especially the atmospheric pollution caused by SO2, CO2, etc. Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60 % of the total. The development of the desulfurization process for sintering flue gases to reduce SO2 emission in sintering process is not only the requirements of sustainable development but also the most important environmental tasks for steel industry [1-5]."

Jan 1, 2011

By M. Cross

Heap leaching presents a complex physico-chemical process to model and a significant challenge to develop a comprehensive model enabling reliable predictions of heap behavior over the long term. A computational modeling framework is described for the analysis of multi-phase flows in reactive porous media suitable for tracking metals recovery, for example, in heap leaching and environmental recovery processes. This modeling framework employs appropriately formulated, parameterized, and solution procedures to capture: 1) liquid and gas flow through heterogeneous porous media subject to variably saturated flow conditions, 2) the complex and dynamically changing nature of the porous media structure, 3) the transport of reactants and products of reaction, 4) the simultaneous mass and heat transfer, and 5) the role of bacteria as a catalyst for reactions. A second class of challenges to accurately model heap processes is to identify and then capture all the process data to characterize the reactivity of particular ores, the mine planning for the construction of the heap, leach schedules, meteorological data, etc. The objective of this paper is to outline these challenges and to describe a modeling framework that can cope with arbitrarily complex geometries and provide tools for rapid and accurate process assessment.

Jan 1, 2006

By Rajashekhar Marthi

Lithium is a key component for future electric vehicle batteries and energy storage. The future availability of lithium to meet the growing demands remains in question. Around 60% of lithium resources exist in the form of continental brines. Traditional methods to recover lithium from brines use solar concentration with precipitation and have found limitations in lithium extraction due to interference of Mg in high Mg/Li brines. Thus, there is a need for highly selective adsorbents. Recently, spinel structured delithiated lithium manganese oxides have demonstrated promising results. However, due to the small particle sizes, it is economically difficult to recover the adsorbents and thereby limits industrial applications. In our work, LiMn2O4 ion sieve was synthesized and immobilized on diatomaceous earth. Fundamental adsorption studies were carried out in lithium buffer solutions to understand the nature of adsorption and kinetics. The adsorbents were also tested for recycle stability, as well as recovery of lithium from Great Salt Lake water samples.

By Anxiang Wang, Kunhua Wu, Yifu Li, Junjie Xu, Yongnian Dai, Bin Yang, Lingxin Kong

In this study, the saturated vapor pressures of tin (Sn) and antimony (Sb), the separation coefficient and the vapor-liquid phase equilibrium of Sn-Sb alloy were theoretically analyzed, which demonstrate that it is possible to separate Sn and Sb by vacuum distillation. The process parameters of vacuum distillation, including the distillation temperature, distillation time and alloy mass (thickness of raw materials) on the direct yield of Sn and the content of Sn in liquid phase were investigated by using single factor experiments. The preliminary results show that the direct yield and the content of Sn are 98.77 wt.% and 96.01% with the optimized distillation conditions of a distillation temperature of 1473 K, a distillation t ime for 45 min and a Sn-Sb alloy mass of 125 g ( thickness o f 8 mm). The distillation parameters in the study provide effective and convenient conditions on separation of Sn-Sb alloy.

Jan 1, 2016

By Alex Luyima, Jaan Kers, Lifeng Zhang

"The pyrolysis of PWBs was investigated by a TG-DTA-MS furnace at 300–1173 K. The kinetics and the control of emitted gas during the pyrolysis of PWBs with and without chemical additives were studied. Moreover, the possibility of controlling the amount of toxic exhaust gases like HBr, C6H6, Br2, Cl2, HCl gas and recovering beneficial gaseous fuels like CH4 and H2 from pyrolysis process is discussed. The MS data for each PWB sample were examined as a function of temperature and particular m/z values could be associated with the mass loss steps in the TG data. The degradation of the organic material was characterized by m/z = 2, 16, 18, 28, 36, 44, 71, 78, 81, and 160. Fe2O3 was the best inhibitor of toxic HBr and C6H6 when compared to Al2O3, CaO Y-zeolite and ZSM-5. Moreover, it had no significant effect on the valuable H2 and CH4 gas evolution. This selective inhibition of toxic gases while maintaining the valuable ones make Fe2O3 the best candidate among the investigated additives in controlling gas emissions from PWB pyrolysis process.IntroductionThe electronic and electric industry is one of the world’s largest and fastest growing manufacturing sectors. As a consequence of this growth, electrical and electronic waste (e-waste), such as computers, washing machines, printers, mobile phones, television sets, stereos, radios, etc., is generated in large quantities around the world. Printed wiring boards (PWBs) are a common component of many electronic and electric systems.[1]. The rapid development and expansion of the electronics industry over the past several decades have led to a dramatic increase in the production of PWBs and a corresponding increase in the amount of waste generated from both production and disposal. The environmental impacts of the treatment and recycling of PWBs waste have become a major concern [1-2]. PWBs are particularly problematic to recycle because of the heterogeneous mix of organic material, metals, and glass fiber [1]."

Jan 1, 2012

By Janusz Majta

The aim of this work is to investigate the control of microstructure evolution through variation of particular deformation parameters in the two-phase (intercritical) region. Niobium-microalloyed and low-carbon steels were investigated. A detailed examination of the factors affecting the ferrite microstructures of tested steels indicated that there were distinct advantages of finishing at temperatures in the austenite-ferrite region. The various results of deformation in the two-phase region are presented. Consequently, the influence of the most important process parameters on the microstructure evolution and mechanical response of the material is determined. The prime objective of the realized research work is the determination of relationship between the history of deformation and final product quality i.e. texture and mechanical properties. To reach the objective, the constitutive equations are proposed for modeling the effects of the hot-deformation process occurring in the austenite and austenite-ferrite region of low carbon and microalloyed steels on the mechanical properties of the resulting product. These models link advanced, finite element approaches simulating metal flow and heat transfer during hot-plastic deformation with constitutive equations describing microstructural processes and mechanical properties.

Jan 1, 2003

By José R. Parga

In some parts of the Comarca Lagunera with population of about 2.5 million people, situated in the central part of northern México, chronic arsenic poisoning is endemic and severe adverse effects attributed to As exposure have been reported. Lifetime exposure to arsenic will develop classical symptoms of arsenic poisoning such as skin pigmentation changes, gastrointestinal disturbances and neurological changes. There are several methods available for removal of arsenic from well water in large conventional treatment plants, however a very promising electrochemical treatment technique that does not require the addition of chemicals or regeneration is Electrocoagulation (EC). The EC operating conditions are highly dependent on the chemistry of the aqueous medium, especially conductivity and pH. In this study, Powder X-ray Diffraction (XRD), Scanning Electron Microscope (SEM), and Transmission Mössbauer Spectroscopy (TMS) were used to characterize the solid products formed at iron electrodes during the EC process. This study will provide an introduction to the fundamental concepts of the EC method. Finally the results of this study suggest that the presence of maghemite and magnetite particles can be used to remove arsenic (III) and arsenic (V). In the field pilot plant scale study more than 99% removal of As species from groundwater is achieved.

Jan 1, 2005

By Mikhail Mikhaylenko

Natural and technogenic sources of rare earth elements (REE) and other rare and scattered metals are remarkable for their chemical diversity. The pregnant solutions going to processing for the valuable metals have very complex compositions. Both targeted elements and competing impurities are present in the solutions in different chemical forms. Thus processing of such materials demands application of different technological tools addressing numerous specific tasks on the way to the final product. Screening work was undertaken to identify the best resins among developmental and commercial products addressing typical cases in the hydrometallurgy of scandium and REE. The cases outline typical sources of scandium and REE, such as streams of TiO2 production, extracted phosphoric acid, barren uranium solutions and others. Specially designed ion exchange resins can be effective tools.

By M. L. Cunha

The lack of control of As and Sb compounds from copper smelters and converters has rendered some chalcopyrite containing arsenopyrite, stibnite and tetrahedrite minerals unusable for metal extraction. In the present investigation, we have studied the carbothennic reduction of Portuguese chalcopyrite mineral concentrate in the presence of lime/CaS04 and CaS04/Si02. Thermodynamic equilibrium calculations were performed to study the distribution of As and Sb between metal and the CaO-Si02-FeO slag phase. The phase equilibrium calculations also show the effect of oxygen partial pressure on the increase in the volume of the slag phase, which helps in lowering the copper metal formation temperature and facilitates a better separation between metal, matte and slag. The reduction reaction kinetics was studied between 850°C and 1100 °C, and the phases formed were identified by X-ray powder diffraction and scanning electron microscopy techniques. The importance of this research for using recycled matte, lean and rich minerals with As and Sb is also explained.

Jan 1, 2001