Search Documents

By P. R. Khangaonkar

The industry of tin ore mining, beneficiation and smelting gives rise to a number of waste products like the beneficiation plant wastes (called amang), tin smelting slags, refinery dross etc. Some of the wastes deserve treatment to obtain economically useful products or to recover the metal values. The paper describes studies conducted on two materials, viz., struverite-middling (struverite-magnetic tin), which is an intermediate product of beneficiation circuits of tin tailings, and tin-smelting slags. The struverite middling was studied for treatment by chlorination using carbon tetrachloride, so as to yield vapour products separable by convenient condensation. The treatment was also found to lead to a tin-rich product amenable for treatment by known hydrometallurgical routes. The tin smelting slag was studied by alkali-leaching so as to avoid any dissolution of iron and it was possible to obtain an iron-free product solution suitable for high purity tin recovery.

Jan 1, 1996

By A. G. Jackson, S. J. P. Laube

"Control of thin films during the growth process is dependent on several parameters that are difficult to monitor, including flux of film material, pressure, substrate temperature, composition, and thickness. One means for easing this difficulty is to take advantage of emission spectra associated with the process and the film. For pulsed laser deposition (PLD), the ion cloud generated by the laser has characteristic emission spectra that can be used to control the flux and, hence, the film. For chemical vapor deposition, the species present can be determined using mass spectroscopy and specific peaks can be used to control the deposition. Raman spectroscopy affords the possibility of real-time control by sensing characteristic peaks associated with film composition and thickness. These spectroscopic methods offer a real-time alternative to process control that is very attractive, because of the ability to accurately control films to achieve the engineered structures and properties sought. Examples are presented to illustrate the capabilities of these methods for thin film preparation.IntroductionThe drive to reduce costs and improve efficiencies of operation sets the tone for much of research, basic or applied. Basic research is limited by the ability of sensors and associated instrumentation to measure parameters accurately and reproducibly. Applied research has the same limitations and also the added constraints of time and costs. Hence, there are strong incentives to explore means for refining existing sensors with respect to performance and cost, as well as finding new sensors and techniques for more accurately and rapidly measuring quantities of interest in experiments and in various processes."

Jan 1, 1997

By Lori Bassman, Cassandra George, Cullen McMahon, Md. Zakaria Quadir, Michael Ferry

"Complete and accurate analysis of subgrain microstructural features must include three-dimensional information. Three-dimensional electron backscatter diffraction (EBSD) data can be used to characterize these features; however their boundaries first must be determined. This cannot be accomplished simply with pixel-to-pixel misorientation thresholding because many of the boundaries are gradual transitions in crystallographic orientation. Fast Multiscale Clustering (FMC) is an established image processing technique that we have combined with quaternion representation of orientation to segment this kind of data. Segmentation algorithms often have issues handling images with both distinct and subtle boundaries. Our implementation of FMC addresses this by using a novel distance function and statistical analysis to take into account the variance in orientation of each feature. Although FMC was originally a twodimensional image processing algorithm it can be generalized to analyze threedimensional data sets. As an example, a segmentation of microbands in cold-rolled aluminum is presented.IntroductionThree-dimensional electron backscatter diffraction (3D-EBSD) is a method for mapping the local crystallographic orientations of points in a volume. The technique uses a dual beam platform consisting of a focused ion beam (FIB) and SEM with EBSD, where FIB is used for serial sectioning and EBSD for orientation mapping of 2D slices. These 2D slices may then be stacked to create a 3D volumetric data set.Typical uses of such a data set include characterizing the geometries and crystallographic orientations of surfaces between structures in 3D [1-5]. This involves identifying boundaries accurately, either in 2D slices with subsequent 3D reconstruction (as illustrated in Figure 1) or in the 3D data set. All such data sets present the challenges of i) aligning data slices to correct for instrument drift, ii) identifying relevant boundaries, and iii) implementing appropriate smoothing or interpolation algorithms. The focus of this paper is boundary identification."

Jan 1, 2011

By G. Belardi

The purpose of the study was to check on the level of environmental contamination and to design a project for cleaning up the Abetina Mine area at Piancastagnaio (Grosseto, Italy). Contamination of this area had occurred during the mining and treatment of cinnabar (HgS) over a prolonged period. The aim of the project is to remove the sources of contamination or render them harmless. Mining of the Piancastagnaio deposit started in 1840, mercury metal being extracted from the ore by thermal treatment. Together with Spain, Italy was the first country to produce this metal and was the world leader in this field between 1936 and 1943. Though mercury production in the Monte Amiata region of Tuscany ceased in 1974 the ensuing environmental impact is very evident, taking the form of rusty old mining and processing works, plus waste tips which still contain considerable amount of mercury even after the ore had been subject to thermal extraction treatment. The research which has been conducted included mapping the area to identify the main sources of mercury and arsenic pollution, as well as the level of environmental contamination. Mercury and arsenic values in excess of 16,000 and 150 ppm respectively are encountered in the most highly-contaminated places. The cleanup project has been drawn up on the basis of the field and laboratory investigations. This provides for a combination of remediation measures on the land concerned, as well as in situ inertization of contaminating elements by means of mixtures of chemical compounds such as cyclosiloxanes. Due account has been taken of Italian and EU environmental regulations when establishing the measures for rendering the various polluting element innocuous. 'The efficacy of the inertization techniques has been checked by yield tests in acetic acid and carbon dioxide, reducing the Hg and As contents of the material in the untreated and treated states from maximum values of 7 mgll to minima close to zero.

Jan 1, 1996

By D. E. Woolley

The rate of reduction of iron oxide from calcia-silica-alumina slag by carbon in liquid iron has been measured over the temperature range 1400-1600°C by monitoring the rate of carbon monoxide (CO) evolution. Slags containing ferric iron have been used in order to study the reduction of both ferric and ferrous cations. Results show that ferric iron is reduced before ferrous iron, so that the ferrous iron concentration increases initially. It is also shown that the rate constant, k, decreases at low reaction rates, or, equivalently, at low concentrations. The authors conclude that the reaction occurs in two periods. During the first period, ferric iron is reduced to ferrous iron. During the second period, ferrous iron is reduced to metallic iron, and the rate-limiting step during the second period is the mass transfer of ferrous cations in the slag phase to the slag-metal interface.

Jan 1, 1998

The oxidation of ferrous ions by oxygen in sulphate solutions is a very slow process, but it tills long been known that the addition of sulphur dioxide increases the rate of reaction very significantly. The kinetics and mechanism of the process were investigated in the laboratory and the results confirmed the advantage of adding small amounts of sulphur dioxide to the oxygen stream for the removal of iron from solutions. The effect of various parameters on the overall rate of iron oxidation and precipitation was studied. In particular, temperature, acidity and composition of the gas mixture were considered and the optimum conditions for the precipitation of goethite were determined.

Jan 1, 1991

By Baozhong Zhao

The direct smelting of copper concentrates to copper metal in a single furnace offers environmental and energy advantages over conventional two-stage copper smelting processes. However, the direct copper making results in unacceptably high level impurities (As, Sb and Bi) in the anode copper. Experimental studies have shown that it is possible to remove these impurities from molten copper by injection of sulfur-hexafluoride. This paper discusses the experimental findings on the influence of various factors on the rate of removal of impurities, such as the impurity inter-effects, initial oxygen content in the metal and injection rate of SF6.

Jan 1, 1995

By Chen Zhang

Polycrystalline Ti-rich NiTi thin films have been deposited from a single NiTi target using a DC magnetron sputtering system. Free standing film was obtained by using a single crystal silicon substrate. Thickness ofthe thin films is controlled at around 12 pm. In this investigation, the effect of deposition temperature on the microstructure and transformation temperatures of the thin films is studied. Influence of post heat treatment temperatures on the properties of the thin films is also investigated. Transformation temperatures of the thin films are determined by differential scanning calorimetry (DSC). The surface microstructure of the thin films is studied using a scanning electron microscope (SEM), and the crystallinity is determined using x-ray diffractometry. It is found that the thin film deposited on a hot substrate is crystalline even when the substrate temperature is as low as 300°C, while the normal crystallization temperature for an amorphous thin film is around 500°C. The microstructure of the film deposited on a hot substrate shows a very fine grain size. The grain size increases with increasing substrate temperature during deposition. The effect of post deposition heat treatment on grain size is minimal.

Jan 1, 1999

By Shangshu Li, Xionggang Lu, Xingli Zou, Zhongya Pang, Kai Zheng, Yinshuai Wang

Metal carbides (MCs), especially transition metal carbides have attracted a lot of attention due to their unique properties, such as high strength and hardness, good chemical and thermal stability. In this paper, a new route was proposed for preparing TiC nanoparticles directly from TiO 2/C precursor by using solid oxide membrane (SOM) technology in molten CaCl2. The TiO2/C pellet pressed under 8 MPa was used as the cathode, and a yttria-stabilized zirconia (YSZ) tube filled with carbon-saturated liquid tin was served as the anode. This process employs an inert SOM to separate the anodic reaction area from the molten electrolyte to control the electrolysis process. The electrochemical process was carried out in molten CaCl2 at 1000°C and 4.0 V from 0.5 to 4 h. The characteristics of the phase composition and morphology of the electrolysis products were investigated. The product electrolyzed was examined by X-ray diffraction (XRD) and scanning electron microscopy (SEM) with energy dispersive spectrometer (EDS). The results show that TiC nanoparticles can be obtained directly from TiO2/C mixture at 1000 °C, 4.0 V and for 4 h in molten CaCl 2 and the current efficiency is calculated to be 74.1%. In conclusion, we suggest that the SOM process is a promising environmentally friendly and low energy costs electrochemical method for the facile and controllable electrodeoxidation of MO x/C precursors to micro/ nanostructured MCs.

Mar 1, 2018

By B. Mishra

The major waste product of the alkaline extraction of alumina from bauxite [Bayer Process] is known as red-mud. Approximately, a ton of red-mud is produced for every two tons of bauxite that is mined. The red-mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that over 90 wt. pct. alumina can be recovered from red-mud by soda-ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of over 94 pct. At this stage, the product could be charged through the tuyeres in an iron blast furnace or smelted to produce pig iron. The mineralogical characteristics of the reduced product are not amenable to magnetic separation for iron recovery. The problems associated with the use of reduced red-mud as an alternative to direct-reduced iron [DRI] has also been discussed. Special attention has been paid to lower the alkali content of the reduced material. If smelted, the concentration of titanium oxide in the slag will be significantly high justifying its recovery by an acid-leach process. This paper describes the successful efforts of iron and alumina recovery.

Jan 1, 2000

By Zhongning Shi, Ramana G. Reddy

"By cyclic voltammetry and potentiostat electrodeposition using Potentiostat/Galvanstat, electrochemical behavior on Ag electrode in electrolyte 0.2M NaOH+0.01MPb(NO3)2-0.01M TeO2 -0.01M TlNO3 solution were also carried out at 298K. The processes of electrodeposition of Tl2Te3 and PbTl4Te3, a thermoelectric material, are reported along with analysis of the composition of the obtained deposits. The results showed that two different underlying processes are occurring depending on deposition potential. One process involves the reduction of TeO3 2- and Tl+ to Tl2Te3 in a potential interval of -0.70V < E < - 0.89V (vs. Hg/HgO). A second process at more negative reduction potentials involves reduction of TeO3 2-, Pb2+ and Tl+ to PbTl4Te3 in a potential interval of -1.02V < E < - 1.19V. The crystalline Tl2Te3 and PbTl2Te3 were deposited electrochemically on Ag substrates at -0.84V and -1.10V respectively. Thermoelectric (TE) material can form a temperature gradient across the material to make electric voltage, which is popular in waste heat utilization and recovery industry. Lead telluride, PbTe, is a small band gap semiconductor of 0.32eV at 300K. PbTe can change its n-type semiconductors with Pb-rich to p-type semiconductors with Te-rich[1]. And it is one of the best TE materials used in thermoelectric generators working between 500K and 600K, or even at a higher temperature of 800K.Three facto,rs play a role in the performance of a thermoelectric material: electrical conductivity (s), thermal conductivity(?), and the Seebeck coefficient (S). These can be combined with absolute temperature (T) to give a figure of merit (ZT) for the material, ZT = s2sT/?. By increasing the electrical conductivity and decreasing the thermal conductivity, which can enhance the ZT value, many efforts, such as alloying with other elements and making the materials nano-sized, have been done to improve its properties recently. Hsu et al. reported that the ZT value of Cubic AgPbmSbTe2+m is increased to 2.2 by doping Ag-Sb to PbTe.[2]."

Jan 1, 2011

By Wenqiang Bao, Qijie Zhai, Ting Wang, Shaobo Zheng, Huigai Li

The type of inclusions with different sizes in as-cast low carbon steel strip which is deoxidized by Si–Mn has been characterized by scanning electron microscope (SEM) and transmission electron microscopy (TEM). SEM observation and analysis suggested that the type of inclusions larger than 1 μm is manganese silicate. TEM analysis was carried out to investigate the composition and structure of nano-inclusions. Inclusions with diameter about 100 nm are manganese silicate, MnS–Si(Mn)Ox complex particles and isolated cubic Al2O3. Furthermore, HREM observations have revealed that there were two kinds of ultrafine particles in size range of 5–10 nm. One is spherical monoclinic Cu2S; the other is silicon-iron oxide particles with morphology of long strip. In addition, some thermodynamic calculations were performed to explain the corresponding relation between the type of inclusions and their size.

Mar 1, 2017

By P. Felix

A discussion on the need of visualization and animation tools in modelling solidification processes is made. An outline of an approach for the production of a video computer animation is provided. A number of examples including, 2 and 3 dimensional melting, filling, and macrosegregation are presented.

Jan 1, 1993

By Bingguo Liu, PENG LIU, Haigang Dong, Jinhui Peng, Libo Zhang

Parameters of technique to decarburize from spent petrochemical catalysts via microwave oxidation roasting were investigated. Decarburization process was performed on a microwave heating system. The results showed that the decarburization percentage of spent petrochemical catalysts was significantly affected by roasting temperature and sample thickness in the range studied. The decarburization percentage was 99.5% in microwave fields under the optimized conditions, roasting temperature 600 °C, roasting time 40 min and sample thickness 2 cm respectively. The residuum after microwave decarburization was characterized by field emission scanning electron microscopy (FE-SEM) which showed that the deposit carbon had been removed effectively.

Mar 1, 2017

By I. D. Reznik

Results of thermodynamic computations have been presented for reactions occurring in the process of segregation roasting of oxide nickel ores to describe more accurately the mechanism of the process. Under conditions of laboratory-scale roasting in combination with close-circuit flotation flow-sheets and magnetic separation, a recovery of 80-82% of nickel into 8 to 10% Ni concentrate and a recovery of up to 66% of cobalt was achieved. Process conditions have been selected for processing of both high-iron and high-magnesium ores. The feasibility of conversion of 94-98% of nickel and cobalt into solution by oxidizing pressure leaching with sulfuric acid has been demonstrated. It has been substantiated that it is reasonable to introduce double-stage segregation roasting.

Jan 1, 2003

By Qingguo Xue, Jingsong Wang, Guang Wang, Yuanyuan Zhang

Due to complicated structure and composition of high-phosphorus iron ore, pure substances were used to simulate the chemical composition of high-phosphorus iron ore to study the reaction of fluorapatite at different temperatures and effect of additives. The gasification process of P during carbothermic reduction process was investigated using a quadrupole mass spectrometer gas analysis. It is found fluorapatite was reduced to phosphorus which diffused into iron and gas phase. From the gas analysis, it was observed that PO and P gas species were vaporized around 800 °C. As the reduction temperature increased, the diffusion of phosphorus into iron was enhanced. The presence of Ca(OH)2 as additives not only promoted the reduction of iron oxide, but also decreased the degree of fluorapatite reaction to inhibit P into iron.

Mar 1, 2018

By F. J. Tavera

The column flotation technology, at first developed for application in mineral dressing, has received special attention in processing of non-mineral dispersions as a result of its low cost, high efficiency and relatively simple operation. This paper presents the results from the operation of a laboratory flotation column for the separation of vegetable oil and soap from aqueous industrial effluents, The flotation system was operated under continuous countercurrent conditions without and with additions of a cationic collector. The experiments show that it is possible to separate about 80% of the organic phase in a rougher flotation stage. These results suggest that the recovery of the organic phase is highly dependant on the dispersion characteristics (i.e. bubble size, gas holdup and bubble surface area flux) and the existing an optimum bubble size from which either smaller or larger, the recovery of the organic decreases.

Jan 1, 2003

By Julien Favre, Akihiko Chiba, Damien Fabregue, Yuichiro Koizumi, Eric Maire

"The mechanical behavior of Co-20Cr-15W-10Ni alloy is studied by compression tests at high temperature. Microstructures after deformation are evaluated using SEM-EBSD. Significant grain refinement occurs by dynamic recrystallization for high temperature and low strain rate (T>1100°C, <0.1s-1), and at high strain rate (~10s-1). Dynamic recrystallization is discontinuous and occurs by grain boundaries nucleation, leading to a necklace structure. The nucleation mechanism is most likely to be bulging of grain boundaries. However, recrystallization occurs also by rotation of annealing twins which can bulge as well. The modeling of mechanical behavior gives a fair quantification of flow softening due to dynamic recrystallization, indicating the progress of dynamic recrystallization with deformation.IntroductionCobalt-chromium alloys are used in biomedical applications for the elaboration of implants due to their outstanding mechanical properties and their high resistance to corrosion. For stent application a large ductile behavior is required in addition to the high mechanical strength. Indeed stents have to undergo a deformation until e˜40% during their expansion [1]. Conventional Co-Cr-Mo (CCM) alloys exhibit limited ductility (maximal deformation about e˜30%) [2]. Co-Cr-W-Ni (L-605) alloy is a better candidate for stent elaboration since its fracture strain can exceed 40% (comparable to nickel superalloys (Figure 1), while it keeps high mechanical strength. In spite of the presence of nickel element in this alloy, biocompatibility is sufficient for vascular implants, therefore L-605 alloy is extensively used for heart valves and stent elaboration [3]."

Jan 1, 2012

By Zhao wen Wang, Ramana G. Reddy, Min Li

"The electroreduction of Co(II) in l-butyl-3-methylimidazolium tetrafluoroborate (BMlMBF4) ionic liquid was investigated by cyclic volatrnmetry at 353 K. The results show that the reaction of Co(II) to Co is irreversible in one step with two electrons transferred. The diffusion coefficient of Co(II) was estimated to be 7.6 x 10-8 cm2 s·1 at 353 K. Then the electrodeposition of cobalt was studied at different cathodic potentials (-0.80 to -0.95 V) and different temperatures (333 to 363 K) in BMIMBF 4 containing 0.20 mol L-1 Co(BF4)z. The deposits were characterized using scanning electron microscope (SEM), energy-dispersive spectroscopy (EDS), and X-ray diffraction (XRD). SEM images show that a uniform, dense, and compact deposit was obtained at -0.80 V and 333 K. The deposits were identified as high-purity metallic Co for all experiments by EDS and XRD.IntroductionCobalt is known as a hard magnetic material and cobalt alloys have been shown to have excellent magnetic properties with adequate mechanical durability and corrosion resistance, which are needed for high performance magnetic recording applications [1-4]. The electrodeposition of Co alloy in the aqueous solution is generally difficult because of the narrow electrochemical potential window of water, which leads to the low current efficiency and worse quality of deposits due to the hydrogen embrittlement. Thus, aprotic ionic liquids (ILs) are expected to be the ideal alternative media for electrodeposition of cobalt or its alloy since ILs usually provide a wide working potential windows, negligible vapor pressure, and acceptable conductivity for electrolysis without the occurring of hydrogen evolution [5, 6]."

Jan 1, 2014

By L. A. Harris

The formation of coke during coal liquefaction can eventually result in catastrophic failure of the conversion system. Coking typically proceeds by the formation of liquid crystals (mesophase) and the subsequent separation of these crystals from the plastic phase formed during heating of coal. The anisotropy of the mesophase makes it readily detectable in the optical microscope under polarized light. This study examines the solids formed during coal liquefaction processing by optical and electron microscopy. Observations on the relationships between the coke morphology, minerals and inert macerals are presented.

Jan 1, 1982