Search Documents

By Keith M. Axler

This report addresses issues specific to the generation of hydrogen fluoride via reaction of calcium fluoride with sulfuric acid. This process has been established on a commercial scale and is under consideration for treatment of calcium fluoride residues from uranium processing. Magnesium fluoride slags are also available as a product of uranium processing. The technique of using sulfuric acid for the production of hydrogen fluoride from magnesium fluoride is also under consideration as a residue processing scheme. In the current study, thermodynamic modeling was used to investigate these chemical processing systems. The results presented herein reveal information relevant to the selection of processing temperatures and conditions. Details include predicted effects in system composition based on operating temperatures for both the calcium fluoride and the magnesium fluoride systems.

Jan 1, 1996

By Cong Wang, Siyang Long, Pengcheng Zhang, Haibin Zuo

The present study describes central segregation of the High-carbon steel billets of 150mm square and its heredity to the following hot-rolled wire rods, whose sizes are 10mm and 6.5mm in diameter separately. The relationship between center segregation of the billets and solute element distribution of rods, the mechanical properties and microstructure of rods were studied experimentally. The results show that segregation index of C is higher than that of Mn. With the increase of central segregation, the stability of the mechanical property of the rods becomes worse. The formation of carbide network and central martensite in the rolled products can be attributed to the heredity of the as-cast central segregation. The 6.5mm-diameter-rod has higher tensile strength than that of 10mm diameter which might be due to bigger reduction ratio. Thermo Mechanical Control Process (TMCP) should be used together with Billet Centersegregation- controlling (BCSC) to improve the overall properties of rolled products effectively.

Jan 1, 2016

By C. D. Seybert, J. W. Evans

"The elimination of convection is essential in experimental investigations of diffusive transport (of heat and matter) during solidification. This paper describes an investigation of an approach whereby a magnetic field gradient is applied to a electrically non-conducting diamagnetic liquid. A magnetic body force then arises which is dependent on the volume susceptibility of the liquid and thereby on the density. With the field gradient aligned vertically and of correct magnitude, the variation of gravitational body forces due to density variations (arising from temperature variations, for example) can be counterbalanced by a variation in magnetic body force.Preparatory to a study of convection control in diamagnetic liquids, PN measurements have been made of the convection occurring during the solidification of water. A peculiar flow arises because of the density maximum at 4°C. Modeling of the flow the steady-state solidification of water in an extremely high field magnet at the NHMFL indicates that flow can be significantly reduced, but it is suggested that, due to field gradient variations within the cell, flow cannot be completely halted. INTRODUCTIONNatural convection is inherently a part of terrestrial solidification. Density-based convection during solidification, due to gradients of temperature and/or concentration, has a significant effect on a material's properties. The design of products with specific material characteristics has required the development of many processes to control convection (such as in the growth of semiconductor crystals, and electromagnetic stirring in steel casting). The expansion of fundamental knowledge about the process of solidification requires collecting data in the absence of density-based convection, while most of science's solidification data (and thus the equations that science has fitted to those data) have been obtained under the influence of gravity. Only relatively recently, through clever experimental design (e.g., drop towers, high altitude parabolic flights, and space laboratories), have investigators been able to study solidification in an environment with ""micro-gravity""."

Jan 1, 2001

By A. Tsubouchi, F. Noguchi, T. Takasu

"A high current density operation is desired to improve the productivity in copper electrorefining. However, a lot of problems still remain such as passivation at anode, dendritic deposition at cathode and impurity behavior during the electro refining.Effects of the current densitY on the morphology of copper deposition on the cathode, and passivation at the anode were investigated at various fluid velocity of electrolyte in the present study.Although a granular appearance of the copper deposition was obtained with increasing high current density, it was depressed by an increase of the fluid velocity of the electrolyte. A uniform deposition on the cathode was also observed when the fluid velocity of the electrolyte become higher. It was ascertained that passivation at the anode was suppressed by circulating electrolyte during electrolysis. INTRODUCTIONIt is desirable to operate at high current density in copper electrorefining in order to improve plant productivity without enlarging the size of electrodes(1). However, there are many problems in copper electrorefining at high current density with the usual commercial practice, for example, anode passivation, dendritic deposition and an increase of impurities in the cathode.In general, it is effective to agitate the electrolyte in order to suppress these problems(2). Smith et a1.(3) have performed electro refining experiments at various current densities in the range of 8 to 32 Aldm2 and at electrolyte fluid velocities in the range of 40 to 120 mlmin, and they obtained well consolidated, void free copper even at high current density in a high electrolyte velocity. However, they did not discuss the recovery ratio and the passivation behaviour at the anode. Walsh et a1.(4)(5)(6) experimented with the rotating cylinder electrode, and ascertained that electrolysis can be carried out at high current densities under the condition of pure electrolyte.With regards to anode passivation, there are several papers by previous workers(7)(8). Our group ascertained the process of producing anode slime during electrolysis(9). However, these experiments were carried out without forced circulation of electrolyte. Therefore, in the present study, to solve these problems, we electrolyzed at current densities in the range of 4 to 50 Aldm2 with circulating electrolyte in the range of 0 to 48 mlrnin. The effect of electrolyte fluid velocity on the surface morphology of deposited copper at cathode and passivation at anode were investigated when electrolysis were carried out with circulating electrolyte at high fluid velocity and at high current density."

Jan 1, 1997

By Yong-Moo Cheong

When the zirconium pressure tube(PT) is in contact with the calandria tube(CT) in the pressurized heavy water reactor(PHWR), the temperature gradient between the inner and outer wall of the PT results in a thermal diffusion of hydrogen(deuterium) and hydride blisters are formed on the outer surface of the PT. Since Zr-2.5Nb pressure tubes have a high risk for the formation of blisters during their operation in a PHWR, there is a strong incentive to develop a method for the non-destructive detection of the blisters grown on the tube surfaces. However, because there is little mismatch in an acoustic impedance between the hydride blisters and zirconium matrix, it is not easy to distinguish the boundary between the blister and the zirconium matrix with the conventional ultrasonic methods. This study has focused on the development of an ultrasonic method to detect the hydride blisters formed on Zr-2.5Nb pressure tubes. Hydride blisters were grown on the outer surface of a Zr-2.5Nb pressure tube using a cold finger attached to steady state thermal diffusion equipment. Ultrasonic velocity ratio method as well as conventional ultrasonic parameters with an immersion technique was developed to detect small hydride blisters on the Zr-2.5Nb pressure tubes.

Jan 1, 2006

By Ki Joo Sim, Sung Beom An, Joonho Lee, Minsoo Shin

Valorization of the electrical arc furnace oxidizing slag by coke was carried out by the reduction of iron oxide in the slag. Since the reduction of iron oxide by solid carbon is an endothermic reaction, supply of heat energy is required. In addition, slag has a low thermal conductivity; traditional fuel injection is not suitable for this reaction. Microwave can be used to supply heat energy to the system. Commercial oxidizing slag was reduced by coke under the microwave irradiation (1.7 kW, 2.45 GHz). The maximum recovery ratio of iron was 87%. In addition, slag composition modification was attempted to use the remaining slag for a mixture in cement clinker. Free-CaO in the slag was successfully suppressed, and the use of the remaining slag as a potential mixture was confirmed.

Jan 1, 2014

By Hwasoo Park

Keywords: FC mold, Argon, Magnetic, Solidification Fluid flow plays a significant role for steel surface quality in continuous casting. Although water models are able to model fluid flow, the flow pattern is not of practical interest since the moving solidifying shell cannot be accounted. Computer modeling has become a popular and dependable tool to analyze the complex phenomena occurring in continuous casting. In this numerical simulation we coupled momentum and energy equations considering the solidification of steel along with turbulence ?-e model. The vertical bending mold is equipped with bifurcated nozzle with 15 degrees of port angle. FC mold is supplied with DC induced magnetic fields. Influence of argon and magnetic fields on molten steel flow and heat transfer is investigated by solving momentum equations adding source terms due to multiphase ? magneto hydrodynamics. The results show that magnetic fields reduce the jet velocity from port by lower magnetic core induced field but the influence on meniscus velocity is complex to describe. Magnetic fields increase surface temperature and homogenize its distribution on surface and inside a mold.

Jan 1, 2005

By Y. A. Chang, L. M. Pike, C. R. Kao

"Knowledge of the site preference of ternary solute additions is essential to developing an understanding of how these solutes affect the properties of B2 intermetallic compounds. A quasichemical model will be presented which is able to predict the site preferences of dilute solute additions to tliple defect B2 compounds. The only parameters required are enthalpies of formation at the stoichiometric composition. General equations are developed which can be used to determine site occupations and defect concentrations for dilute as well as non-dilute solute additions. These equations use atom pair bond enthalpies as the parameters. It is found that the site preferences of dilute additions are not always in agreement with predictions based on the solubility lobes in ternary Gibbs isothelms. Predictions for dilute additions to NiAl and FeAl are compared to expel1mental results found in the literature. Satisfactory correlation is found between the model and the experimental results. In addition, the predictions from the model on vacancy concentrations in Fe doped NiAl are compared to recent experimental results by the authors.1.0 IntroductionIntennetallic compounds with the B2 crystal structure such as NiAl and FeAl have been investigated recently for possible use as structural materials in high temperature, oxidizing, and/or corrosive environments. The major limiting property of these materials has been a lack of sufficient room temperature ductility. Attempts to improve the ductility have often been made through ternary or higher order alloying. For B2 compounds, substitutional alloying additions can occupy either of the two sublattices and this site occupancy can be crucial in determining how the alloying addition affects the properties of the alloy. In this manuscript we will discuss the use of thelmodynamic modeling to predict the site occupancies of ternary alloying additions in B2 compounds with the triple defect structure."

Jan 1, 1996

By Ana Bohé

Nowadays, Gas-solid processes are widely used in the industry. The chloration and carbochlorination of metallic compounds are some of this kind of non catalitic heterogeneous reactions. In particular those related with extractive metallurgy of refractory elements (Zr, Ti, Nb, Ta, RE, etc). The development of materials to be used in reactors at elevated temperatures and with high corrosion performance, enhance the application of this kind of processes. Although they are currently carried out in the production of many comodities, the mechanism of most of them are yet not well understood. The present work is a deep discussion on the most important aspects to take into account for determining the mechanism of gas- solid reaction, and those criteria fulfil in this analysis were applied to chlorination and carbochlorination examples. The microstructural characteristic of solids, the mass and heat transfer phenomenon, the adsorption and desorption of gaseous species on active surface, surface diffusion processes and chemical elementary steps, which are the mainly contributions to the mechanism of these reactions were analysed. Furthermore, the effect of them on the reactivity of solids and the control step of the reactions were determined. The application of catalitic mathematical models to this kind of reaction and the modification for the better interpretation of experimental results is also undertaken. The most appropriate experimental procedures for following these reactions and the microstructural characterization techniques needed to be use in each case, there limits and applicability are also indicated.

Jan 1, 2006

By D. Van Dooren

The final goal of the research project is to develop a 3D FEM model that is able to predict the kinetics and micro-structural evolution during the bainitic transformation. The input parameters consist of thermodynamic and atomic mobility data obtained from the ThermoCalc and mCTRA databases combined with structural mechanics data extracted from the stress-strain curves of the fcc and bee phases. In this paper the general principles of the model are outlined and some interesting preliminary results are shown and commented. The full implementation of the model has presently not been achieved yet. In the model the bainitic transformation is considered as a sequence of martensitic (re)nucleation and growth of a ferritic subunit followed by the carbon rejection into the surrounding austenite. The (re)nucleation of the subunits will be described through a non-classical martensitic nucleation criterion. Once a nucleus has been activated at a specific location in the material, a full-sized subunit is instantaneously formed through a displacive mechanism. The stress state in the system that arises due to the transformation strain can be calculated by a 3D FEM programming code. Immediately after the formation of the subunit, another 3D FEM programming code calculates the carbon diffusion from the supersaturated ferrite into the surrounding austenite. The resulting stress state and carbon profiles will be used to determine where and when a new subunit will nucleate based on a renucleation criterion. Keywords: Bainitic Transformation, Modeling, Eshelby, Carbon Diffusion

Jan 1, 2003

By T. Shimizu

In Japan, the emission standard of selenium in effluent was set at a maximum of20 mgll in Feb. '94 for the first time, and it is scheduled to be further decreased to a maximum of 0.1 mg/I from Feb. '97 due to tightening of the Water Pollution Prevention Act. Selenium (IV) and (VI) are generally found in effluent from precious metals refineries. Although selenium (IV) can be easily eliminated by some reducing agents, selenium (VI) is more difficult to be reduced. Therefore, many smelters are having difficulty in complying with the new emission standard. At Mitsubishi Materials' Naoshima smelter, the behavior and the elimination of selenium in effluent have been extensively investigated. As a result, it was found that two strategies were particularly effective. One of them is improving the overall operation of precious metals refinery, that is, feeding uniformly the effluent to the waste-water treatment plant, reducing the effluent volume by recycling and recovering more selenium (IV) in the effluent. The other is eliminating selenium (VI) in the effluent from the precious metals refinery. It was found that selenium (VI) can be effectively reduced by using hydrazine under high? sulphuric acid concentration and high temperature conditions. By using these measures, it is considered that Naoshima Smelter will be able to comply with the new emission standard.

Jan 1, 1996

By Bruno Lebon, Koulis Pericleous, Georgi Djambazov, Mayur Patel

"High speed compressible jets are used in a number of steel-making applications. In the case of the BOF, a compressible oxygen jet reacts with a carbon-rich iron bath to reduce carbon levels and produce steel. The intensity of the process is governed by the speed of the jet and by the size and shape of the depression created in the metal and slag by the force of the jet, i.e. by the corresponding free surface. This is a difficult CFD problem, since there are compressible and incompressible regions in the flow domain, which need to be handled differently in a finite-volume (FV) pressure-correction scheme. Also, standard turbulence models do not account for compressibility, or the large difference in density between the cold oxygen jet and the hot reacting surroundings. Corrections are introduced to the k-E model to remedy this deficiency and the results are validated against experimental data. The compressible/incompressible boundary is handled through a transition region, based on Mach number.IntroductionThe deformation of a free surface by a compressible high speed jet is of paramount engineering interest, particularly for understanding the physical processes within a Basic Oxygen Furnace (BOF). In a BOF, a supersonic oxygen jet impinges on a molten iron surface, thereby creating a cavity. Oxygen penetrates the bath and removes carbon, resulting in low carbon steel [1].The challenges in modelling such a process lie in coupling a solution domain with distinct compressible and incompressible regions and in dealing with large density differences between the modelled gas and liquid. The modelling of compressibility within the jet is crucial, since the correct velocity profile in the jet is required to determine the cavity depth with accuracy."

Jan 1, 2012

By Merete Tangstad, Fei Li

This paper studies the quartz and carbon black pellets at elevated temperature with varying temperature and gas atmosphere. High-purity quartz and commercial ultra-pure carbon black was mixed (carbon content wt.15%), and then pelletized into particles of 1-3mm in diameter. The stoichiometric analysis of the pellet during heating is studied in thermogravimetric analysis (TGA) furnace at different temperature in CO and Ar atmosphere. The microstructure, phase changes and element content of sample before/after heating is characterized by X-ray diffraction, scanning electron microscope, X-ray fluorescence and LECO analyzer. The reaction process can be divided into two stages. Higher temperature and argon atmosphere are the positive parameters for SiC formation.

Jan 1, 2016

By Zbigniew Smieszek, Ryszard Chamer, Ryszard Prajsnar, Zygmunt Kurek

"Lead-containing wastes processed at the IMN’s Division in Legnica originate mainly from dry and wet dedusting installations of the technological lines for copper production. These are lead dusts and lead-zinc dusts characterised by the specific properties resulting from the chemical composition of the Polish copper concentrates. Besides lead, they contain many accompanying metals and impurities such as zinc, copper, sulfur, chlorine, potassium, sodium, and also bituminous substances. Processing of lead-containing dusts is conducted in the installations of rotary-rocking furnaces heated with gas-oxygen burners fitted with auxiliary systems for cleaning process gases and refining re-circulating dusts. The processing technology utilizes innovative process and technical solutions enabling disposal of lead-containing wastes from copper metallurgy and from non-ferrous metals industry according to the BAT recommendations and to the guidelines specified in integrated permission. In this paper, the main technological aspects of processing lead-containing dusts at the IMN’s Division in Legnica have been presented.IntroductionCrude lead is obtained in Polish lead metallurgy from various primary and secondary materials, such as Zn-Pb concentrates, lead-bearing dusts of copper metallurgy and battery scrap. In zinc smelter Miasteczko Slaskie S.A. crude lead is produced from sulfide and oxide Pb-Zn concentrates in ISP process. Orzel Bialy S.A. and Baterpol Ltd. produce crude lead in short rotary furnaces in the process of smelting products of mechanical battery scrap separation– desulfurised or not desulfurised paste and metallic fraction. KGHM Polska Miedz S.A. and IMN Divison in Legnica produce crude lead in rotary furnaces in the process of smelting of polymetallic dusts and slimes from copper production processes."

Jan 1, 2008

By Dinesh Goyal

Industrial fly ash from (electro static precipitator) was mixed with soil at different levels on v/v basis for raising of pulpwood tree species. In field trials conducted on degraded soils increase in the plant growth of Eucalyptus tereticornis, Acacia auriculiformis and Casuarina equisetifolia by 10 %, was observed during the initial six months after plantation at 18-24% (v/v) fly ash concentration which was at par with chemical fertilizer treatment. Level of As, Se and Mo in flyash was 6.2, 3.6 and 4.0 ppm respectively. The radioactivity analyses 40K, soil and 28 fly ash showed that the activity levels of gamma emitting radionuclides K, Ra, Ac were within the permissible limits and mixing of fly ash with soil at tested concentration would have no deleterious effects. Available Co, Cr, Ni and Cd in rhizospheric soils were below detection limit. Fly ash at 10-20 % level (v/v) was also found to be a good potting mix material in forestry nurseries in terms of improving biomass production by 20 %, when tested in nursery seedlings of Eucalyptus tereticornis. Nursery addition of fly ash in soil decreased soil dehydrogenase activity and the soil bacterial population was negatively affected. These results indicate that use of fly ash in forestry sector involving nursery and plantations as a soil amendment agent upto 10-20 % v/v is a gainful utilisation of fly ash.

Jan 1, 2002

By R. Nilsson

In the present work the sulphide capacities of Ca0-Mn0-Si0, ternary slags have been measured in the temperature range 1798 - 1873 K by equilibrating the slag with a gas-mixture containing CO, CO,, SO, and Ar. The results are compared with the data reported in literature. A theoretical model has been developed in the present work where the sulphide capacity is expressed as a function of the slag composition and temperature. The model enables the estimation of sulphide capacities of complex slags with a knowledge of the capacities of simpler systems.

Jan 1, 1994

By Gerardo Fuentes

The stoichiometry and kinetics of the hydrothermal reaction of enargite in copper sulphate solutions was investigated in the range 140–300 °C, and particle size under 15 and 50 μm. The stoichiometric experiment was performed at 300 °C, using one gram of sample (96% enargite, 4% tennantite) and 100 mL of copper sulphate solution (10 gpl) at 1.2 pH. Enargite reacted completely after 80 min. A solid product was obtained and characterized by XRD. The main product was chalcocite (M) and some traces of djurleite and chalcocite (Q). Tennantite did not react under these conditions. The kinetic experiments were conducted at 140 °C, 190 °C, 250 °C and 300 °C. From fitted data and Arrhenius equation the calculated activation energy (Ea) was 51 kJ/mol. According to the hydrothermal transformations studied, the reactivity of different phases found in the copper concentrates was bornite > chalcopyrite > covellite > sphalerite > pyrite > enargite > tennantite.

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been investigated on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27 degrees between each tuyere, and five side tuyeres with an angular separation of 22.5 or 27 degrees between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

By Jian Pan, Zhen He, Deqing Zhu, Shouyan Yue

"The differences of raw material characteristic among six kind of iron concentrates and the influences on ballability were studied from the aspect of the size distribution, specific surface area and particles morphology. The results show that the specific surface area of iron concentrates has crucial influence on ballability, and the effective method of improving ballability for weak ballability iron concentrate has been found. It is of important guidance for Chinese steel mills to import and use iron concentrate from the whole world.IntroductionChina's steel industry has developed rapidly in recent years, crude steel production in 2011 is an unprecedented 683 million tons, which is almost half of the world crude steel production, and it is equivalent to the total sum production of the nations which rank at 2,3,4,5 and 6 in the world [1]. In order to match the development of steel industry, the blast furnaces are becoming larger and more modernization, therefore charging burden of higher quality is requested, and the reasonable blast furnace burden structure is more and more important, at the same time, for iron ore powder sintering process's continuous improvement and development, another method providing ""concentrate"" for blast fumace-pelletizing is also taken seriously. The grate-kiln method of pelletizing has achieved great development for its unique advantage, and in just a few years, there are over 60 rotary kiln production lines have built or being built in China, the sum of pellets has reached to more than 140 million [2, 3]. The rapidly growth of pelletizing yield demands diverse source of pellet, which include not only domestic magnetite concentrate, but also imported hematite which is high in iron and low in silicon. Usually the ratio of imported hematite concentrate increased gradually. The imported hematite concentrate has high grade and fine particle size (the content of -0.074 mm mostly higher than 90%), but the ballability of part of the concentrates is poor."

Jan 1, 2013

By F. Z. Utyashev

The present work considers the essence of fragmentation: on the level of a simple model as a material response to the curvature accumulated by it at large deformations. It is on this basis that the correlation between curvature and fragment sizes is determined. It is shown that at deformation the area of curvature center inevitably changes. It is revealed that a specific value of variation of center surface area, i.e. ^As parameter, is numerically equal to the value of curvature acquired by a material. Minimum sizes of fragments and grains depending on ^As have been estimated, and the dependence of this parameter on strain has been established. Besides, the present paper considers the effects exerted by curvature center geometry, material distortion, directions of deformation and thermal warming up in the localization zones on structure refinement when various techniques are applied.

Jan 1, 2006