Search Documents

By S. Yokoya

With increasing requirement of steel productivity and quality in continuous casting in the conventional casting system using an immersion nozzle, it is very difficult to establish a reasonable molten flow pattern. In order to overcome this difficulty, we propose a new method of imparting swirling motion onto the flow in the immersion nozzle and to control the flow pattern in the mold. Following results have been obtained during the studies. For the case of slab continuous casting mold: High amplitudes of oscillation with a period of 10 to 15 seconds are observed in the outlet flow of the immersion nozzle and meniscus flow in the conventional casting system, while these phenomena are remarkably suppressed using swirling motion in the immersion nozzle, which leads to very calm and uniform flow pattern at the outlets of the immersion nozzle, in the mold and on the meniscus in the mold; For the case of billet continuous casting mold: (1) heat and mass transfer near the meniscus can be remarkably activated compared with a conventional straight type immersion nozzle without swirl, and (2) Quite different mold flow patterns are observed between the divergent and straight immersion nozzles. Heat and mass transport in the mold using the divergent nozzle is much more reasonable compared to that of straight nozzle. The findings, mentioned above, are very useful to control the flow pattern in the slab, and billet continuous casters. Such effectiveness of swirling flow in the SEN on the mold flow has been put into practical use. As a result, remarkable progress on the quality and production of continuous casting products has been observed in practical application.

Jan 1, 2006

By Ulises Crossa Archiopoli

We describe a technique that allows rapid imaging of the thermal diffusivity of the sample by a modified photo-thermal technique. The thermal diffusivity in hardened steels strongly correlates to the hardness. Hence in a noncontact manner and with optical microscope resolution, a 2D map exhibiting the crystallographic phases and hardness of the sample can be retrieved. Two almost collinear laser beams scan the surface, one as a modulated pump and a second as a CW probe. The deflection of the probe carries information on the thermal expansion of the sample and with it, on the thermal diffusivity. It is shown that a single determination of the time delay of the modulation of the probe beam can be used to retrieve the thermal diffusivity.

Jan 1, 2010

By A. V. Tarasov, S. D. Klushin

493 The most common method for minimizing the copper content of residual slag in the process of autogenous smelting of sulfide raw materials is treatment of molten slag in an electric furnace, with optional addition of solid reducing agents, such as coke, and/or sulfiding agents such as pyrite. A drawback of this technique is the fact that the final slag produced still contains 0.5% or more Cu. We have tested a method for treating molten slag obtained as a result of autogenous smelting by a gaseous mixture of sulfur dioxide and methane at a ratio of. SC:SO2 = 0.75 :1.0 in the presence of oxygen. Interaction reaction within the SO2-O2-CRi system proceeded at a high rate at 1373 to 1573 K to form reducing and sulfiding agents: H2S, S, COS, CO, CO2, H2, H2O. The gas mixture requirement was about 100 to 150 Nm3 per 1 tonne of slag. A decrease in the ferric iron concentration (Fe3+) from 10-15% down to 2-3% resulted in lower solubility of copper in slag, and agitation of the melt with gas stream accelerated. the separation of the sulfide phase and slag. Removal of copper from slag was performed in a pilot unit within the second V anyukov furnace zone where slag arrived with a copper content of 0.8-1.3%. The temperature of molten slag was maintained within 1523 to 1573 K. The copper content of the final slag was at a level of0.12 to 0.14%. The matte sent to converting was a mixture of bottom matte from the smelting zone and the slag treatment zone. It had a copper content of about 50 to 55%. Process gases from both furnace zones were combined and sent to the acid plant for sulfur recovery. This process was offered for commercial use at two copper smelters in Russia and CIS.

Jan 1, 2000

By Bradley C. Bockrath

Some thirty coals were evaluated for liquefaction activity under a mixture of CO and H2 at 425° C. The viscosity of the liquid products was taken as an indicator of the degree of liquefaction. It was found that the direct liquefaction of a particular coal may be beneficially influenced by the presence of pyrite. Active pyrites are often found in the native mineral matter of the coal itself. For example, subbituminous and bituminous coals and lignites of relatively high pyrite content were found to liquefy more readily than similar coals or lignites which were poor in pyrite. The reactivity of inactive coals could be improved by using blends with active, pyrite-rich coals. In addition, pyrite was effective when added separately as pyrite concentrates obtained from coal beneficiation operations. Various other iron- and sulfur-bearing additives were also effective when used in combination as added slurry-phase catalysts, including iron oxides and mineral residues derived from liquefaction of active coals. Under liquefaction conditions, pyrrhotite ( Fe I- x5) is formed from pyrite or from the iron oxides and many sulfur containing species. Pyrrhotite was shown to be a hydrogenation/dehydrogenation catalyst for tetralin but is not active for initiating a variety of free radical reactions that do occur when pyrite is heated with tetralin. The role of pyrite in coal liquefaction is complex and still not well understood.

Jan 1, 1981

By A. Mejias, M. A. Garcia, G. Diaz

During 1997 and 1998 two successful zinc feasibility studies, Skorpion and Sanyati, were carried out by Tecnicas Reunidas based on the modified ZINCEX® technology. The technical viability of each project was proved during more than 600 h of continuous running in a pilot plant. The Skorpion zinc project would recover 150,000 t SHG Zn/y from an oxidized zinc ore of a Namibian mine. The economical study showed that the plant would have the lowest production costs in the world. The Sanyati zinc project would treat a bleed from an existing copper refinery in Zimbabwe to recover 5,000 t SHG Zn/y. In the first case the electrowinning cellhouse was supplied by Union Miniere and in the second by Tecnicas Reunidas. This article highlights the pilot plant results and the advantages of the proposed process over conventional zinc production practices.

Jan 1, 2000

By R. M. Luna-Sánchez

Electrochemical studies, particularly Evans? diagrams, have been employed in hydrometallurgy to simulate and explain the redox phenomena that take place at mineral and metal surfaces during operations such as leaching and cementation. However, despite their utility, in some cases, the combination of the cathodic and anodic branches, determined separately, does not reproduce the chemical environment present when both processes occur simultaneously on a specific surface. In the present paper, limitations of Evans? diagrams are analyzed through two examples: silver sulfide cyanidation and gold cementation on zinc. In both cases, the surface kinetics are sensitive to the local pH and cyanide levels. When the electrochemical oxidation of silver sulfide or the reduction of gold are performed in the absence of its corresponding redox reaction, the local pH obtained does not simulate the real situation and the combined reaction kinetics may be very different from those determined from the Evans? diagrams.

Jan 1, 2003

By Z. Sun

Imposing a strong magnetic field is considered to be an attractive method to prepare materials with aligned or textured structures due to its intrinsic properties, e.g. non-contact and easily controllable. However, the nature of the strong magnetic field effect still remains unclear and further research is needed. In the present paper, the effect of a strong magnetic field on the solidification of a hypereutectic Al-Cu alloy was investigated. After magnetic field treatment, the primary phase was aligned parallel to the magnetic field direction. Meanwhile, the eutectic micro-structural constituent became elongated and thinner. A theoretical analysis was conducted to have a better understanding of the phenomena. During solidification, the magnetic Faraday and dipole-dipole interaction forces are considered to decrease the solute pile-up in front of the solid-liquid interface and modify the eutectic cell formation. The alignment of the phase is due to the shape magnetic anisotropy and crystal magnetic anisotropy.

Jan 1, 2010

By P. Meyers, F. DeSilva, L. Gottlieb

A number of tests looking at lead removal using ion exchange resins of various types from various aqueous streams have been undertaken. The tests focused on strong acid cation (SAC) and weak acid cation 0N AC) resins. It was found that the mechanism of lead removal is partly by lead filtration rather than solely by ion exchange in a large portion of the applications studied. This is not surprising since lead carbonate is essentially insoluble and almost all water supplies contain at least some carbonate alkalinity. Regeneration of lead from exhausted resins containing significant amounts of lead may not be practical in some cases because of the large chemical and waste volumes involved. Since lead, .·along with many other very insoluble metals, is often present as a suspended solid rather than in ionic form, ion exchange is probably not always the best technology for bulk lead removal.

Jan 1, 2000

By WU Jian-hui

Keywords: metallic material; nickel powder; thermal decomposition; precursor; fibrillar powder; nanometer scale; passivation treatment The precursor thermal decomposition process of fibrillar nanometer scale nickel powder and passivation treatment of obtained powder are investigated, and the composition and morphology of the products are characterized by use of IR, TGA/DTA, XRD and SEM. The results show that the precursor morphology is a decisive factor to the product morphology of the nickel powder. The morphology of the product derived at low decomposing temperature is irregular. The nickel powders produced at the temperature higher than 480 coheres seriously. The product particles are reunited with the decomposition time prolong. The powder prepared under the optimal condition is fibrillar like woolen yarn; the grain diameter is less than 50nm.

Jan 1, 2005

By Onuralp Yucel, Ahmet Turan, K. Can Candeger

Exothermic riser sleeves are important tools to increase solidification duration, particularly for iron-steel casting. Increasing the time to solidus improved casting product quality by minimizing cavities. Therefore, process costs were significantly reduced. In comparison with the use of unsleeved risers, exothermic riser sleeves retain up to 30–35% of the heat and increase the duration to solidus by nearly 50%. Exothermic riser sleeves are a mixture of metallothermic-based exothermic and insulating materials that are manufactured in different sizes and shapes. Various suppliers produce these sleeves in different compositions. However, the designers must clearly understand the thermochemical and thermophysical properties. The purpose of the present study was to experimentally determine the effects of varying experimental parameters such as reaction duration, flammability and temperature change etc. on selected exothermic sleeves. The results were compared with thermodynamical simulations which were performed using the contents and the corresponding thermophysical properties of exothermic sleeves.

Mar 1, 2018

By Mari Naess, Jan Erik Olsen, Gabriella Tranell

"Fume, also known as dust, is produced during metal refining. Exposure to fume is damaging to the health of plant operators. A mathematical model has been developed to study the different factors governing the fuming mechanism. It is shown that natural convection is the main driving force of the phenomenon, and that the fuming rate is highly sensitive to the area of the exposed metal surface. A new feature introduced in the modeling concept is the ability to include a gas flux of unconsumed process gas flowing up through the metal surface. This reduces the fuming rate, and should normally not be neglected.IntroductionFormation of fume from the ladle in which metal is refined into its final specifications is an environmental issue of importance for the working environment in the production plant. In layman-term fume is often known as dust. It is formed when metal reacts with oxygen. As an example of a fuming process, we will focus on ladle refining of silicon. Note that many of the principles and conclusions will apply to other metal refining processes. For silicon production, silica fume (S1O2) is produced when silicon metal (Si) reacts with oxygen (O2).Silicon is produced in a submerged arc furnace. The metal is tapped from the furnace into a ladle for refining. The refining is conducted by injecting a mixture of air and pure oxygen at the bottom of the ladle. The oxygen reacts with the metal and the impurities, and the amount of impurities is reduced according to product specification. At the ladle surface, metal also reacts with oxygen present in the air surrounding the ladle. This reaction produces silica fume as illustrated in Figure 1."

Jan 1, 2012

By Edmundo Manilla, Merete Tangstad, Daniel Davila, Eli Ringdalen

FeMn alloys are typically produced with lumpy ore or sinters. Minara Autlan, the Mexican FeMn producer, is however making Mn-nodules as a raw material for Mn-alloy production. The Mn nodules have been characterized by XRF, XRD, by wet chemical methods and by EPMA. The Mn/Fe ratio is somewhat lower compared to commercial Mn ore on the marked. The basicity of the ore is however close to 1, and additional fluxes may not be used. The Mn-nodules will be in a state of manganosite (MnO), tephroite ((Mn, Ca)2SiO4) and galaxite ((Mn,Mg)Al2O4). This leads to a low melting temperature area. A low porosity and low amount of higher Mn-oxides gives a high thermal strength to the nodules.

Jan 1, 2016

By Hee Dong Jang

Crystalline metal oxide nanoparticles such as lithium cobalt oxide (LiCoO2) and indium tin oxide (ITO) were synthesized from sprayed droplets of aqueous precursor solution by flame spray pyrolysis. Complete thermal decomposition of the aerosol precursors was obtained at high flame temperature. Molar concentrations of the precursor solution, and the flow rate of combustion gas such as hydrogen, oxygen and air were varied to control particle size, size distribution and crystal structure. The crystalline nanoparticles synthesized were nearly spherical, and their average primary particle diameters ranged from 11 to 35 nm for LiCoO2 and from 8 to 15 nm for ITO.

Jan 1, 2006

By Toshiyuki Hashida, Victor M. Lopez-Hirata

"Small-punch tests and determination of fracture toughness JIC were conducted at 4 and 77 K on new cryogenic JN1, JJ1 and JK2 austenitic stainless steels, after isothermal aging. Equivalent fracture strain ?qf determined by measuring the reduction of thickness in the small-punch test specimen. A linear dependence of JIC on ?qf was found in these new materials. Regression analysis of experimental data produced the following linear relation JIC = 1304.1 ?qf + 8.09 [kJm-2]. An analysis of present work relation was pursued on the basis of material properties and evaluation method of he. Results showed that the slope value has a strong dependence on material yield strength and JIC evaluation method. This linear relation is useful for the evaluation of fracture toughness JIC, measuring the equivalent fracture strain ?qf by means of small-punch test. Thus it can be useful for assessing the degradation of fracture toughness in small areas such as, the heat-affected zone in welded components.IntroductionCryogenic structural materials for superconducting magnets of fusion nuclear reactor are required to possess a good combination of strength and toughness. The mechanical properties are required beyond the capability of conventional austenitic stainless steels [1]. New cryogenic JN1, JJ1 and JK2 austenitic stainless steels were developed by the Japan Atomic Energy Research Institute (JAERI) [1]. The structure of superconducting magnets is constructed by welding of 200 = thick plates of these steels, which are solution treated at high temperatures and then water-quenched to avoid intergranular precipitation. However, the welding process involves heating and cooling [2], which cause microstructural changes in both base metal and weld. In this heterogeneous microstructure, it is important to estimate the fracture toughness of these materials at cryogenic temperatures. Therefore, it is necessary to evaluate the effect of aging process on the fracture toughness behavior of these new steels. To determine the cryogenic fracture toughness, the elastic-plastic JIC value has been co=only used [2]; however, the specimen size is much larger than heat-affected zones in welded components. Small-punch (SP) testing method, employing miniature specimens, has permitted to evaluate the fracture toughness behavior at different temperatures in different nuclear reactor materials [3,4]. Mao et al. [5,6] and Misawa et al. [7] found a linear relation between JIC value and equivalent fracture strain ?qf, determined by SP method in non-ferrous alloys and ferritic steels at room temperature and austenitic stainless steels at 4 and 77 K, respectively. So that, this kind of correlation would be very useful to assess the fracture toughness JICe values by means of SP test in small zones of welded components."

Jan 1, 2012

By Yuanpei LAN, Minren XU, Deliang NIU, Zhu WANG, Qingcai Liu, Shan Ren

Removal of gas is the major function of RH degasser. To optimize the RH refining craft in Chongqing Iron and Steel Co. Ltd, the degassing effect of RH degasser at different degrees of vacuum was investigated using a vacuum induction furnace. In addition, the effect of processing time on the gas content dissolved in molten steel was also studied. The results showed that degree of vacuum was one of the important factors that determined the degassing efficiency in RH refining process. High vacuum degree is helpful in the removal of gas, especially in the removal of [H] dissolved in molten steel. The processing time could be reduced from 25-30 min to 15 minutes and gas content could also meet the demand of RH refining

Jan 1, 2015

By Eren Hüseyin Obuz

In this study, the leaching kinetics of rare-earth elements were investigated using HCl and HNO3 solutions. A standard crushed complex ore was utilized as raw material. The complex ore (particle size of under 54 μm) contains REE (Ce, La, Nd, Pr, etc.). Different leaching durations were selected for the kinetic studies. The highest leaching efficiency was obtained in HCl solution, and the leaching mechanism was identified to diffusion through a product layer. The rate constants of Ce, La, Nd, and Pr were calculated as 1.08 × 10−2, 0.86 × 10−2, 1.87 × 10−2, and 1.34 × 10−2 h−1, respectively.

By I. Perus, M. Fazarinc, G. Kugler, M. Tercelj

"Ledeburitic tool steels are highly alloyed steels used for specific highly loaded applications but are characterized by low and variable hot workability. In this contribution the importance of selecting the right choice of some essential process parameters, i.e. casting temperature, solidification rate and soaking temperature, needed for improving the intrinsic hot deformability of ledeburitic tool steels, is studied. An inappropriate selection of casting temperature and cooling rate results in precipitation of unusual eutectic carbides that decreases the hot workability, whereas with the selection of appropriate soaking temperature the temperature range of safe hot working can be broadened. For each initial as-cast microstructure individually determined soaking temperature should be selected.IntroductionThe surface cracking during hot deformation of ledeburitic tool steels reduces mechanical properties and their industrial yield. These tool steels have high hardness, wear resistance and high tempering resistance on one hand, and high flow stresses and low hot deformability on the other. Decreased hot deformability of the tool steels is attributed to the type, size, shape, distribution, fraction of eutectic carbides and/or other phases, grain growth, etc. at upper limit while precipitation of secondary carbides and decreased recrystallization rate at lower limit of the safe hot deformation temperature range, [1-6].The occurrence of cracks on most exposed areas of workpiece are related to the areas where similar conditions related to upper and/or lower limit of temperature working range prevail, i.e. areas with accelerated cooling, areas with higher value of accumulated strains where also decreased recrystallization rate with simultaneously presence of higher tensile stresses takes place, furthermore areas of workpiece which are due to combustion conditions in furnace heated to higher temperatures, etc. Thus the areas, where combination of previously mentioned conditions prevails, are more exposed to cracking. This additionally requires that hot deformability of ledeburitic tool steel should be considered as a complex problem. Publications in the literature with regards to hot deformability of tool steels are predominately of a partial nature thus all reasons for unexpected occurrence of cracks are not sufficiently explained in available literature so far. Furthermore modern practice proves that previous processing parameters significantly influence the hot deformability and thus this cannot be considered as a constant value. During heating, soaking and hot deformation various processes take place: decay (decomposition) of carbides, formation of new carbides, dissolution of carbides and of alloying elements, etc. Thus depending on variation of process parameters and chemical composition, that consequently influences the processes related to carbides, shifting of decreased deformability at both limits of temperature working range to higher and/or to lower temperatures can occur, [1-14]."

Jan 1, 2012

By Bowen Li, Jiann-Yang Hwang, Mingsheng He, Huaguang Wang

Kyanite is one of the major high-alumina minerals for producing refractory ceramics. At high temperature, kyanite can be decomposed into mullite and amorphous silica. This change is an irreversible decomposition and provides potentials for fiber reinforcement of ceramic matrix. In this study, kyanite powder was compressed into a cylinder green body of ceramic and heated at 1150–1450 °C.The phase transformation of kyanite and sinterability were investigated by X-ray diffraction and scanning electron microscopy. The results showed that the phase transformation of kyanite started at 1150 °C when rising the temperature. At 1350 °C, kyanite is completely converted into mullite and silica. The compressive strength of the ceramics reached 73.3–134.8 MPa, while the bulk density was 1.95–2.47 g/cm3. The microstructure indicated the correspondence of the compressive strength to mullitization degree of kyanite.

Mar 1, 2017

By A. A. Bustos

A model was developed to simulate the blow-by-blow operation of the converting process. From the weights, compositions and temperatures of all converter feeds the model calculates the composition and tonnage of both converter matte and slag as well as bath temperature at the end of each blow. The development of the model and its application to the converter aisle operation are described. There is good agreement between model predictions and observed results. At the present time the model is being used to investigate different converting schemes and their effect on pay metal recoveries, slag chemistry and temperature of the bath. Future work involves the use of the simulation model as a process control tool for the converting operation.

Jan 1, 1988

By A. J. Williams, T. N. Croft, M. Cross

"The computational modelling of extrusion and forging processes is now well established. In this work a novel approach is described which utilises finite volume methods on unstructured meshes. This technique can be used to solve simultaneously for fluid flow, heat transfer and non-linear solid mechanics and their interactions. The approach involves the solution of free surface non-Newtonian fluid flow equations in an Eulerian context to track the behaviour of the workpiece and its extrusion/forging, and the solution of the solid mechanics equations in the Lagrangian context to predict the deformation/stress behaviour of the die. Some preliminary examples of this approach will be discussed.IntroductionThe computational modelling of extrusion and forging processes is now well established. Within the last 20 years the finite element method has become the most commonly used technique to simulate metal forming processes [1]-[4]. The Lagrangian and Eulerian type of formulation have been the two major approaches to this problem.Lagrangian methods are efficient and suitable for handling non-linear problems in which small strains prevail, boundary conditions do not change with the course of deformation, and where mesh distortion is not a critical factor in the analysis. Unfortunately, the above points are essential to any accurate metal forming analysis. The problems of mesh distortion and element entanglement pose a serious drawback on the use of such methods. Some automatic remeshing techniques have been developed for Lagrangian finite element analyses of metal forming problems [5]-[7]. However, these methods are not robust and efficient enough to remedy the mesh distortion problems in general. An alternative is to update the mesh manually but this is not always possible, and even when it is feasible it involves major interaction by the user. In addition, remeshing is usually applied to the whole domain which is not necessary and increases CPU time. The complexities associated with remeshing also affect the ability to parallelise the code."

Jan 1, 2001