Search Documents

By E. Munnik

The Chambishi Metals Cobalt Plant in Zambia has recently installed a novel oxidation/precipitation pressure leach process as part of the COSAC (Cobalt from Slag and Copper as by-product) Project. An iron-cobalt-copper alloy, produced by the carbothermic reduction of slag, is atomized and pumped to the COSAC Leach Plant, where cobalt and copper are recovered as dissolved sulphate salts, and iron is rejected primarily as hematite. Cobalt and copper are subsequently recovered as cathode metal in the existing Chambishi operation by conventional electrowinning. This paper examines the challenges faced during the design and subsequent successful commissioning of the COSAC Leach Plant.

Jan 1, 2003

By James D. Navratil

Advances in hydrometallurgy require the introduction of new separation and purification processes, but they can be complex, costly and energy intensive. Chromatographic processes have low energy requirements and possess very high separation efficiencies. However, they have not yet made the great industrial impact that might be expected from their benefits. The large-scale and difficult separation of rare earths would greatly benefit from an improved continuous chromatographic operational device. Truly continuous, multicomponent chromatographic separations may be achieved by means of the continuous annular chromatograph. Work has been Initiated at The University of New South Wales involving the improvement and development of such equipment for the separation and purification of rare earths.

Jan 1, 1990

By K. P. Nishad

The origin of many casting defects can be traced at the mold filling stage. Entrapped air/gas pockets and oxide film formation are notable examples. In the present work, the mold-filling process is simulated using a mathematical model, built on a multi-physics based commercial package PHYSICA. The simulation code has the capability to solve multi-phase problems. The numerical model addresses a complicated dynamics of filling operation including free surface flow and subsequent flow behavior and is based on conservation of mass and momentum. The Free surface is modeled using the scalar equation method (SEM). The model is validated with benchmark experimental results from the literature. The role of turbulence and the pouring rate on variables affecting sites prone to oxide film formation are investigated using a simple but novel technique. Key findings of the work are presented.

Jan 1, 2006

By Wen-Ming Chien, Vamsi Krishna Kamisetty, Amrita Mishra, Ivan Gantan, Prathyusha Mekala, Dhanesh Chandra

"The phase equilibrium and characterization studies by using high temperature X-ray diffraction (XRD) and differential scanning calorimetric (DSC) methods have been performed for binary organic thermal energy storage materials. The organic thermal energy storage materials undergo a solid-solid state phase transition before melting which stores large amounts of thermal energy. Two materials [tris(hydroxymethyl)aminomethane(TRIS) and 2-Amino-2-methyl-l, 3- propanediol(AMPL)] were used for this study. Binary samples of AMPL-TRIS were prepared to perform high temperature XRD characterization and DSC studies and the binary AMPL-TRIS phase diagram was developed. The high temperature solid-state phases of AMPL and TRIS were characterized as a disordered BCC structure. It was found there is virtually no solubility of TRIS in AMPL or vice versa below -75 °C. The maximum solubility of TRIS in AMPL is 11% TRIS at 75 °C. The eutectoid transformation was shown at 19%TRIS-81%AMPL composition and at a temperature of 75°C. Lattice expansion calculations on single phase of TRIS and AMPL have been performed.IntroductionThermal energy storage materials can store a large amount of heat due to the presence of thermal transitions from the orientationally ordered to disordered phases occurring before melting. These molecules (such as amine and alcohol derivatives of neopentane) can reorient as a whole about the central carbon atom to form orientationally disordered crystals (ODIC) and their spherical shape makes them reorient relatively easier. Thermal energy storage materials are becoming increasingly important as a renewable energy resource. These molecules undergo large changes in enthalpies at solid-solid transitions. The presence of these compounds with large enthalpy changes are identified as potential thermal energy materials and some of die applications are solar cell systems [1-3]. Binary mixtures have been found as a way to adjust the transition properties in addition to pure compounds [4]. Tris(hydroxyrnethyl)aminomethane (TRIS, C(CH2OH)3NH2) and AMPL, CH3C(CH2OH)2NH2) are two important thermal energy storage materials."

Jan 1, 2012

By H. Jiang, S. Yang

"The main processes for nickel metallurgy in China consist of electric arc furnace smelting to produce low grade nickel matte and converter to high grade nickel matte, grinding and flotation to separate nickel sulfide from copper sulfide and direct electrolysis of nickel matte. Systematic studies on the properties of electric furnace slag, smelting process for nickel matte, anodic process of nickel matte, cathodic process of nickel electrolysis have been done in our labs. In addition, an approach to a new hydrometallurgy process for nickel matte has been done. The feature of the new process is one stage acidic leaching of high grade nickel matte. The leaching solution could be purified by deposition way or by solvent extraction way. There are two leaching rate-determing steps, chemistry reaction-determing one at temperatures below 600C and diffusion-determing one at temperatures higher than 600 c. The acidic leaching fraction reacted dvaties with leaching time t according to the equation 1-(1- a ) 1/3=kt. The experimental data also show that the leaching reaction rate varies with concentrations of H+, Cl-, and it is also effected by copper sulfide and Cu++. The Cu++ ion can retard the leaching reaction due to forming a copper sulfide layer on the matte surface and the equation 1- 2/3 a. - (1- a: ) 2/3 akt can be used for the case. However the copper sulfide added into nickel matte can facilitate the leaching process. The research work for nickel metallurgy done by others in China has also been mentioned in this paper.Large scale production of nickel in China started in 1960s.The main processes consist of electric arc furnace smelting to produce low grade nickel matte and converter to high grade nickel matte grinding and floatation to separate copper sulfide from nickel sulfide and direct electrolysis of nickel matte.To reduce nickel loss in slag a reseaech group organized by Jinchuan Company and Central South Institute of Mining and Metallurgy (now the Central South University of Technology) measured the viscosity surface tention density conductance melting point and structure of the slag(I).lt has been found that the physico-chemical properties of the slag depend on the components SiO2 ,MgO and FeO but FeO in the slag is too high and the statistic analysis of data from industry gave an equation to correlate the content of Ni in slag with the content of Ni in matte and the composition of slag again it was pointed out that the content of FeO in slag effected the loss of Ni in slag very much (2). The ratio (FeO+MgO) to SiO2shouid be less than 1.13 and the content of Fe3O4should be as low as possible but the reaction"

Jan 1, 1988

By Pan Cao

The process of reduction roasting of nickel laterite with rotary hearth furnace combined with magnetic separation becomes a very potential way to prepare ferronickel alloy, especially for the low grade nickel laterite ore. In order to realize this new process, the effect of roasting temperature, time and additive on the reduction degree were investigated in the laboratory experimental. The results indicated that the recovery rate of Ni increased with the roasting temperature increasing to 1500°. Most of nickel and a spot of iron are selectively reduced with adding 25.19% SiO2, 6.42% coal, and roasting for 60min at 1500℃. Then conventional magnetic separation was carried out. The content of Ni and Fe are 7.50% and 59.08% in ferro-nickel nugget prepared by this method. And the recovery rate of Ni is 90.91%, which indicates that a high recovery of ferro-nickel from nickel laterite ore is achieved indeed.

Jan 1, 2014

By Per Anders Eidem, Merete Tangstad, Jens Davidsen

"During excavations of submerged arc furnaces producing silicomanganese, silicon carbide (SiC) has been found. Contributing to the size of the inactive area of the furnace, the active area of the furnace where reactions occur will decrease, thus reducing the potential for pre-reduction in the furnace.This work studied the formation of SiC from the liquid-solid reaction between slag, metal, and metallurgical coke. Slags and metals with different levels of silica (S1O2) and silicon (Si) have been studied. The slag and metal has been heated together with coke, and the samples investigated by microprobe. The results show that SiC was formed on the coke particle through reactions with both slag and metal. For the metal, the carbon most likely diffused through the SiC to react with Si in the alloy. SiC formation with slag is likely to go through the reduction of Si02 to Si.IntroductionToday, Silicomanganese (SiMn) is produced in submerged arc furnaces (SAF) by reduction of S1O2 and manganese oxides, mainly with metallurgical cokes. Typically, the tapped metal has a silicon content of 17 - 20 wt.%. To achieve higher levels of Si, the metal can be refined by adding off-grade silicon metal, yielding low carbon SiMn. [1]. What is believed to be SiC that has been found during dig-outs of SiMn furnaces producing high silicon alloy. It is possible that excess amounts of SiC in the furnace cause operational problems, since SiC will occupy furnace volume. As SiC accumulates, the active volume of the furnace will decrease, increasing the flow of material and gas in the active areas of the furnace. Formation of SiC is inevitable, so it is desired to keep the formation as low as possible. To be able to control the formation of SiC, one has to understand the basic mechanisms."

Jan 1, 2012

By Qingyu Deng, Shiwei Ma, Wang Hua, Guibao Qiu

"The flow properties of the blast furnace slag bearing high TiO2 at high temperature like the viscocity may change a lot due to the formation of the carbonitride inside, causing serious problems on the separation between the metal and the slag. Therefore, the critical condition of the formation of Ti(C,N) in blast furnace is vital importance for the ironmaking process with iron ore bearing titania. In this study, the formation of Ti(C,N) in blast furnace and the influences of various factors on the Ti(C,N) formation are investigated by FactSage. It is found that the mass of Ti(C,N) would reach the maximum at 1480 oC, and the product is mainly TiN below 1620 oC, while it is mainly TiC above 1620oC. The order of the factors by the importance from strong to weak was: temperature, the content of TiO2 in slag, basicity of slag, the content of MgO and Al2O3.IntroductionThe titanium dioxide (TiO2) in iron ore bearing titania will be partly reduced by carbon to titanium carbonitride (Ti(C,N)) in blast furnace, causing serious problems on the separation between the metal and the slag because of the change of flow property. Therefore, the critical condition of the formation of Ti(C,N) in blast furnace is vital importance for the ironmaking process, especially for the smelting of iron ore bearing titania. Extensive experimental data in regard to the formation of Ti(C,N) has been reported in numerous papers[1-6]. However, only some discrete data can be obtained by experiment, and it is difficult to detect the mass of Ti(C,N) in slag. In addition, the experiment is difficult to be proceeded when the temperature is above 1600oC. Therefore, it is very difficult to make clear the critical condition of the formation of Ti(C,N) by experiment."

Jan 1, 2012

By Tatsuki Uzawa, Takashi Nagai

The consumption of Nd and Dy is increasing dramatically because of an exceptionally high demand for Nd-Fe-B-(Dy) magnets and a significant amount of the magnets are wasted. It is important to develop a recycle process the elements from the wasted magnets. In this study, Nd and Dy were extracted from the magnets by silver at high temperature. Nd can be extracted more than 70 % by silver. However, Dy is extracted only 25 % in the same experimental condition.

Jan 1, 2014

By C. M. F. Vieira

This work has as its objective to characterize ceramic bodies for vitrified tiles elaborated with the mixture of nepheline-syenite flux and kaolinitic clay. Formulations were prepared with 0, 30 and 50 wt.% of nepheline-syenite incorporated in a kaolinitic clay. To determine the physical and mechanical properties such as dry bulk density, linear shrinkage, water absorption and flexural rupture strength, specimens were prepared by 30 MPa uniaxial pressure-molding and then fired in a laboratory furnace at 1150oC. The microstructure of the fired ceramics was evaluated by scanning electron microscopy. The results indicated that the nepheline-syenite improved the evaluated properties of the clay and attended the specifications of vitrified ceramic tiles.

Jan 1, 2010

By Krzyszof Borowiec

With the aim of determining the thermodynamic conditions for sulfation of impurity elements, in particular magnesium, in titaniferous slags the equilibrium gas composition for the sulfation reaction: MO + so2 + 1/2 02 = MS04 has been studied by an EMF technique with a solid zro2 + Cao electrolyte. Here M denotes the impurity elements: Mg, Ca and Mn, and the following _oxide systems have been studied: Ti02-MgO-Fe2 o 3 , Ti02-MnO-Mn2 o 3 , and Ti02 -CaO-Si02 , all in the . temperature range 700-1000ºc. Reproducible EMF values were obtained by adding small amounts of -Na2so4 to the oxide-sulfate mixture. From the observed results the Gibbs energy of formation of the phases Mg 2Ti04 , MgTi03 , MgTi 2o 5 , MnTi03 , CaTi03 , and CaTiSio5 , as well as the activity of MgTi05 in the solid solution with Fe2Ti05 have been calculated. The results show that, from a thermodynamic viewpoint, sulfation of these impurities in titaniferous stags i:s favorable- at around and below 800ºC.

Jan 1, 1985

By Zhou Wenbin

In this paper the mechanical properties of high carbon equivalent cast iron for automobile brake discs were analyzed through thermal analysis curves. Experiment results show that the mechanical properties have a strong correlation with thermal analysis curves and an effective way to predict the mechanical properties of high carbon equivalent cast iron was proposed based on the features of thermal analysis curves.

Jan 1, 2010

By M. H. Erten

Most of the fourteen workable coal seams in the State of Missouri have high ash and sulfur levels and need beneficiation in order to meet customer and Environmental Protection Agency requirements. If proper ash and sulfur removal methods can be designed, more Missouri coals will be mined and used within the state. One of the main objectives of this research is to investigate the possibility of removal of sulfur of Missouri coals by conventional beneficiation methods.

Jan 1, 1982

"Mixing phenomena in a bottom blown air-stirred one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor was studie9-using three different configurations of straight circular nozzles fitted axially at the bottom of the vessel. The mixing time has been determined by pH measurements at various gas flow rates, bath heights and nozzle orientations in the presence and in the absence of a second phase.Experimental results reveal that the mixing time decreases with increasing gas flow rate. For a given gas flow rate the mixing time increases non-linearly with increasing bath height. Off-center configuration gives slightly lower mixing times as compared to center configuration. It is found that the contribution of buoyancy to the total stirring energy density is very small, but its contribution increases with increasing bath height. In the presence of an upper oil layer, the mixing time increases significantly for all configurations.IntroductionIn high temperature metallurgical melts mixing is carried out by injection of a gas either from top or bottom of the vessel in order to accelerate the rates of chemical reactions and to promote bath homogenization. When a gas is injected into a liquid through a submerged lance, porous plug or nozzle, the gas, rising as a two phase plume to the surface, imparts momentum to the surrounding liquid and causes gross circulation in the bath which promotes mixing."

Jan 1, 1997

Based on experimental and computer simulation results from our group, we report a systematic, atomic level analysis of carbon dissolution from carbonaceous materials in molten iron. Experimental results on graphite / Fe-C-S system were obtained using carbon dissolution studies, XRD and FESEM investigations and were supplemented with Monte Carlo simulations. Three basic mechanisms, namely carbon atom dissociation rate, interfacial phenomena and mass transfer in the melt were found to be responsible for the overall dissolution process. While mass transfer in the melt is governed by the concentration gradients, melt composition and temperature; impurities present in ash play a significant role in the interfacial phenomena. For less ordered forms of carbonaceous materials, carbon atom dissociation rate depends strongly on the degree of long-range order and is an important rate controlling mechanism in the overall dissolution process. A systematic comparison of dissolution rates for a variety of coal-chars, natural and synthetic graphites has been carried out in an attempt to identify rate-controlling mechanisms. The structure of the carbonaceous material appears to be an important underlying factor in the carbon dissolution process.

Jan 1, 2003

By Thomas Schuman, Jaan Kers, Lucas N. W. Damoah, Xiangjun Zuo, Lifeng Zhang

"Rapid technological innovation has propelled the use of electronic equipment leading to the generation of more and more waste electrical and electronic equipments (WEEE). Printed wiring board (PWB) is a component made of one or more layers of insulating material with electrical conductors. To investigate an environmentally friendly process to recycle PWBs, PWB samples with and without additives were pyrolyzed. Liquid, gas and solid products were achieved with different conversion fraction. Analysis of the exhaust gases from the experiments using GC-MS and MS showed that without CaCO3 additives poisonous gases such as C6H6 and HBr were produced which were adequately controlled if CaCO3 was added.IntroductionPyrolysis is one of the best methods for treating complex mixtures of waste polymers and to recover the material and energy content. The process consists of thermal decomposition at moderate temperatures in total absence or small amount of oxygen in which the structures of polymers break down into smaller intermediate products "". The decomposition temperature of a substance is the temperature at which the substance breaks up into smaller substances or into its constituent atoms 2). Thermal treatment of PWBs were reported using DC Arc Plasma furnace 3), and fixed bed reactor 4). One drawback in dealing with thermal treatment of PWB scraps is the likely production of super-toxic halogenated dibenzodioxins and dibenzofurans from the bromine containing structures. Pyrolysis of organic materials contained in waste PWBs leads to the formation of gases, oils, and chars which can be used as chemical feedstock or fuels ""'. Dehalogenation of the pyrolysis product of electronic scraps is essential to make it commercially acceptable. It would be obviously the most advantageous solution as pyrolysis and dehalogenation are carried out simultaneously. Reported pyrolysis investigations are at experimental stage and have been carried out in vacuum, molten salt, fluidized bed, rotary kiln, entrained, stationary, and moving bed reactors 7). Comparing to the incineration and combustion of PWBs, the pyrolysis process has several characteristics: 8'"">) 1). Converting the organic solid substance into fuel gas, fuel oil and carbon-black as storage energy; 2) Emitting toxic substances such as sulfur, bromine and heavy metals in wastes; and 3) Keeping metals from being oxidized. Although many researches into the pyrolysis of PWB wastes have been reported, most of the works have been carried out using analytical pyrolysis techniques or very small batch reactors ""~'5). Also, most of the works for the pyrolysis of PWBs haves concentrated on the composition of the organic products, particularly the brominated organics. The current study is to investigate the pyrolysis of PWB powders in a small TG-DTA scale and a 50-gram tube furnace scale."

Jan 1, 2011

By Jilai Xue

Oxygen gas bubbles generate on anode during Pb electro-deposition process in PbSiF6-H2SiF6 aqueous solutions at room temperature. Cell voltage varies as the bubbles formed on the anodes surface. The bubble layer on the anode makes a voltage drop that consumes energy in the Pb process, which can be reduced by applying ultrasound on the anode. The effects of ultrasound frequency and anodic current density were investigated with ultrasound on and off, alternatively during the Pb electrode-position process. The removing of the gas bubbles were recorded in association with a drop in the cell voltage. The cell voltage can be lowered by 4% - 6% with ultrasound, which has potential for energy saving in Pb production.

Jan 1, 2010

By H. J. Thevik, A. K. Dahle

"A mathematical model that calculates the stress development in a coherent and stationary dendritic network due to interdendritic flow is proposed. The fluid flow is assumed to be related to the solidification shrinkage, and under the assumption of no porosity formation and unidirectional solidification, the shrinkage-induced flow within the mushy zone is calculated analytically. The interdendritic melt flow exerts a force on the solid network and an analytical expression for the stress build-up in the network is developed. Parameter studies illustrating the influence of cooling conditions, mushy zone length, dendrite coherency, fraction solid, volume fraction of eutectic, and solidification shrinkage upon the stress development within the solid network are presented. Comparing the magnitude of the calculated stresses to measurements of the strength in equiaxed mushy zones shows that it is possible for the stresses to exceed the strength, thereby resulting in reorientation or collapse of the dendritic network.IntroductionInterdendritic fluid flow is at present regarded as a very important mechanism for feeding of shrinkage during solidification of metal alloys. Solidification of many alloys is often characterised by heterogeneous nucleation of the primary phase on substrates in the melt with subsequent evolution of equiaxed dendrites. These equiaxed dendrites can initially grow freely, but impinge on each other and form a continuous dendritic network, ie. dendrite coherency, quite early in the solidification process. Measurements of the dendrite coherency point have shown that the dendritic network is established at solid fractions ranging between 0.1 and 0.5, and most often around about 0.2 [l]. Depending on the alloy composition this means that as much as 70 to 80% of the volumetric shrinkage has to be compensated by flow of liquid through the interdendritic network. Interdendritic flow occurs with a much larger resistance compared to free flow of the liquid and flow of a liquid with dispersed crystals. The pressure drop associated with the interdendritic flow increases rapidly with decreasing fraction ofliquid."

Jan 1, 1999

By Jinjing Dua, Jun Zhua, Kuiren Liub, Bin Wang, Xiaolei Wua

V-Ti-Fe as hydrogen storage alloy was prepared by reducing metal oxides with a metallothermic reduction method. The deoxidation process of the V-Ti-Fe alloy was performed by electro-deoxidation and vacuum induction melting method, respectively. The results showed that the content of oxygen impurity can be controlled at about 0.2wt% after electrolyzing for 240min. Both the maximum values of hydrogen absorption capacity and the effective hydrogen desorption capacity are 2.65wt% and 1.01wt%, respectively. The deoxidization effect of vacuum induction melting process is more remarkable, with Ce as the reducing agent. It is found that Ce addition is beneficial for reducing the componential segregation, promoting the hydrogen absorption activation of V-Ti-Fe alloy. When m(Ce)/m(alloy) is up to 5%, the oxygen content has been reduced to 0.05wt% and the maximum hydrogen absorption capacity and the effective hydrogen desorption capacity are up to 3.36wt% and 1.85wt%, respectively.

Jan 1, 2015

By Andreas Weber

Batrec operates a plant for the recycling of used dry batteries with a capacity of 3000 tons per year. The plant Is situated In a tourist area of Switzerland and has complied with all the strict emission restrictions. The process yields four products: FeMn. Zn, Hg and slag. No hazardous waste Is produced. All types of batteries can be treated.

Jan 1, 1995