Search Documents

By Benoit DeBecker

Laboratory-scale experiments have shown that chromium metal could be recovered from chromate wastes by modifying slightly the chromium electrowinning flow-sheet. After reduction by sulhr dioxide and precipitation of chromic hydroxide, the solid residue is dissolved in the chrome alum solution and the metallic impurities are removed by cementation on manganese. The presence of dissolved manganese in the electrolyte does not affect the cathodic deposition of chromium and it eliminates the anodic production of Cr(V1).

Jan 1, 1994

By Ryan Walton

The Flash Converting Furnace at Kennecott Utah Copper converted over 465kmt of high-grade matte in 2002 but was restricted due to low matte production to 395kmt in 2003. This paper presents updated operational performance data and describes improvements implemented since the mid 2001 rebuild. Matte burner feed distribution, silica and arsenic impacts on settler lime-based slag operability, blister laundering, uptake/boiler accretion control, and dust sulfation will be discussed, as well as current development requirements dictated by operational imperatives and furnace modification plans.

Jan 1, 2005

By Zviad Kovziridze

The problems related to the production and research of SiC-Si3N4 composite are presented. The technology of producing the protective casings for tips and thermocouples is developed. Optimum composition charge and technological parameters are defined. The results of casing testing at production plants are presented.

Jan 1, 2006

By Batric Pesic

Adsorption of gold on activated carbon from gold bromide solutions was examined as a function of pH, particle size, carbon amount, initial gold bromide concentration, bromine concentration, temperature, and various cations and anions. pH did not have any effect below pH=6. Above pH=6, pH had dramatically negative effect. The adsorption results satisfied a first reaction order model. The reaction rate constant was proportional to the inverse of carbon particle radius. It was also proportional to the amount of carbon, and independent of initial gold concentration. Temperature had a very little effect at pH=l. At pH=8, the activation energy was a function of the extent of a reaction, increasing with the extent of a reaction. Cu, Fe, Ca, Mg, and Na cations and sulfate, chloride and bromide anions did not have any effect on gold adsorption. Bromine had a very negative effect on gold uptake.

Jan 1, 1991

By C. A. Summers

The U.S. Bureau of Mines applied process mineralogy to investigate a lead and zinc deposit located near Story Creek, Colville Mining District, Alaska. Mineralization is hosted by the Kayak Shale in veins, veinlets, and breccia. Sphalerite and galena, with supergene anglesite, occur in symmetrical quartz veins and between breccia clasts. The study sample analyzed 2.11 percent Pb, 5.37 percent Zn, 0.014 percent Cu, and 1.2 oz/ton Ag. Analyses of crushed products showed that 33 percent of the sample weight, and more than 50 percent of the Pb and 65 percent of the Zn, are in the minus 850 um fraction. Liberated grains of sphalerite and galena were found in crushed products finer than 300 um. Beneficiation tests indicate the material is amenable to processing by traditional gravity and flotation techniques.

Jan 1, 1991

By Manolete Mena

WC-Co nanocomposite powder is among the first group of materials with a promising potential for nanocrystalline-materials application. A chemical vapor synthesis (CVS) process that has previously been used for preparing the aluminides of titanium and nickel, and other metallic and intermetallic powders has been applied to the preparation of WC-Co nanocomposite powder. This CVS system was designed so that a tungsten precursor (WCl6 powder) and a cobalt precursor (CoCl2 powder) were separately fed into each evaporator in a reactor by means of specially designed powder feeders. The reduction and carburization of the vaporized chlorides by methane-hydrogen mixtures produced nanosized WC and Co composite powder. The product is a very uniform mixture of the constituent powders, which is important to ensure a high quality of the bulk cemented tungsten carbide product after consolidation. In the present work, the effects of reaction temperature, CH4 to WCl6 ratio, CH4 to H2 ratio, residence time, and Co content on the powder composition and particle size were determined. The products were characterized using XRD, carbon analyzer, and TEM.

Jan 1, 2006

By Jack S. McPartland

The recent developments on the concentration and recovery of gold from leached gold thiosulfate solutions by solvent extraction, reduction-precipitation, and electrochemical deposition are reviewed in this paper. Alkyl phosphorus esters have been found to extract gold only in alkaline thiosulfate solutions, The recovery of gold increases with thiosulfate concentration in the aqueous phase and with alkyl phosphorus esters concentration in the organic phase with aliphatic hydrocarbon diluents. The addition of ammonia improves the extraction. The extraction of gold with amines in either aliphatic or aromatic diluent decreased in the following order: primary>secondary>tertiary amines. Increase in the extractant concentration at high pH increased the extraction of gold. At pH < 9, the primary amine, RR&apos;CHNH2 with 1&apos;9-23 carbon atoms is the main extractant with TBP as the synergistic reagent and at pH >9, the primary amine shows a synergistic effect on the extraction of gold&apos; with TBP. TheAu(I) ions in thiosulfate solution are reduced by sodium borohydride (SBH) to metallic gold, with particles in the sub micron range, At an SBH/ Au ratio of 6.25, pH = 6, and at room temperature, the I e ppm Au(I) in a solution of ] 0 gil thiosulfate was completely reduced to metallic gold in about 60 minutes.

Jan 1, 1999

By Y. Huang, P. B. Prangnell

"An Al-0.1Mg alloy was firstly deformed at room temperature by ECAE to a true strain of 10, where a steady state deformation was established and further processing had little effect on grain refinement. The ECAE samples, with an average grain size of ~0.55µm, were then compressed in a channel die at 77K- 473K to various reductions. Microstructures were characterized by electron backscatter imaging and EBSD in a FEGSEM. Grain refinement to the ECAE submicron structure occurred during deformation at cryogenic temperatures of 77 – 213K, whereas coarsening took place during deformation at elevated temperatures. A steady state deformation was observed at all temperatures where a constant grain structure was developed and maintained upon further straining due to dynamic recovery. The mechanisms of dynamic recovery during steady state deformation at cryogenic temperatures are discussed.IntroductionSevere deformation processing (SDP) has been successfully used to produce submicron grain structures, and in some cases nano-scale crystallite sizes, in a wide range of alloys. However, the rate of grain refinement becomes increasingly inefficient at high strains as a steady state grain structure is approached [1-3]. Steady-state grain sizes have also been reported in other ultra-high strain deformation processes, like cryogenic ball-milling [4]. There is thus a minimum grain size achievable in a material by a given SPD process under constant deformation conditions.It is well documented that a steady state subgrain size is observed in warm deformation of metals due to dynamic recovery (e.g. [5]). In severely deformed alloys a constant grain size at ultra-high strains has similarly been attributed to dynamic recovery [1-3]. Mechanisms have been proposed, for rapid deformation induced grain growth including stress driven boundary migration and breakaway from solute pinning [2]. However, as pointed out by Humphreys et al. [2] the restoration processes are currently poorly understood, particularly at low temperatures, where the boundary migration rates required to maintain a constant grain size are orders of magnitude higher than can be satisfactory explained from diffusion controlled migration. Similar to the subgrain size, the steady state grain size obtained during SDP is generally related to the temperature compensated strain rate [2, 6]. Thermally activated restoration processes are thus expected to be suppressed by lowering the deformation temperature and a smaller steady state grain size can be achieved."

Jan 1, 2012

By Zizheng Zhou

The separation of cobalt from other base metals can be achieved using diffusion dialysis in a two-compartment reactor separated by an anion exchange membrane. In this work, a Neosepta AFX membrane was used to study the separation of various metals in an acid-chloride solution. The separation of one metal from another was investigated on the basis of the various chloro-complex stabilities. The metals investigated included cobalt, nickel, copper(II), iron(III), aluminum, zinc and cadmium. The impact of several critical experimental conditions, including the initial metal and chloride concentration in the feed solution and their initial concentration in the receiving solution, on the separation factor and the metal transfer rate is reported in this work. Effective separation of different metal pairs was achieved under the experimental conditions.

By James D. Navratil

Neutral bifunctional organophosphorus solvent extractants (such as carbamoylmethylphosphonates and carbamoylmethylphosphine oxides) strongly extract lanthanides and actinides and do not extract more than 40 other elements from mineral acids. Because of their excellent properties they have been found useful for F-element recovery and purification processes. A brief overview of the lanthanide and actinide extraction chemistry of these reagents will be given.

Jan 1, 1990

By W. F. Drinkard

Many in the environmental movement have focused on this element. But, nothing they or anyone does will change the amount of arsenic in the world. This report is on actual commercial plants that we developed and operated to recover or stabilize arsenic values from metallurgical dusts from gold and copper pyro operations and arsenical gold bearing ores. When they were available gold and copper values were recovered. Our experience in arsenic extends over thirty years. My first corporation, Mineral Research & Development Corporation was the first in North America to manufacture the then new CCA (copper-chrome-arsenic) wood preservatives. This class of wood preservatives proved to be so effective that it made wood into an entirely new material of construction. It is not uncommon for wood properly treated with arsenical CCA preservatives to last for thirty; forty, and sixty years. Over a hundred years have been projected in some field tests. Hundreds of thousands of trees have been saved. Millions more trees would have been saved had environmentalists not decided that their arsenic phobia was more important than trees. There are several variations of CCA. The most popular is CCA-C. Its formula is: CrO3 . . . . . . . . . . . . . . . . . . . 47.5% CuO . . . . . . . . . . . . . . . . . . . 18.5% As2O5 . . . . . . . . . . . . . . . . . 34.0% Until recent restrictions were placed on the consumption of arsenical wood preservatives, annual consumption in North America was about 150,000,000 lbs./yr. About 64,500,000 of arsenic as the pentoxide was safely consumed this way. World CCA consumption has been about double the above figures or 300,000,000 lbs. as 100% CCA and 129,000,000 lbs/yr as As2O5. Close to 100% of all the arsenic used in wood preservatives is derived from gold or copper processing. The valence of arsenic required for CCA wood preservatives and many other markets is the same valence that is required for stabilization. The economic challenge is how to get there. We have built and operated eleven plants to oxidize arsenic trioxide to its pentavalent form. Most of these have been classic in that they used a common oxidants such as hydrogen peroxide or nitric acid to achieve this.

Jan 1, 2005

By Shane Andrews, Gustavo Vasquez, S. K. Varma

"The effect of solutionizing time on the corrosive wear behavior of 2014 aluminum alloy has been studied using the impact and continuous mode of scratching techniques. The transient currents (TC) evolved during the scratching of the alloy shows a linear dependence between the TC and the solutionizing time. Higher TC values at longer solutionizing time may be associated with the changes in the concentration of quenched-in vacancies, grain sizes and dislocations generated during scratching. These factors can either create (a) anodic sites or (b) pitting corrosion resulting in the generation of transient currents. The results have been compared with the similar study carried out for 6061 aluminum alloys. This 6061 aluminum alloy shows similar behavior but the rate of TC generation per unit solutionizing time is much lower than 2014 aluminum alloy. The morphological changes in the impact scratches and the TEM investigation in the scratch have been presented in this paper.IntroductionThe technique of studying corrosive wear of composites of 6061 aluminum in the monolithic and reinforced forms has been reported in the literature [1]. Two modes of scratching, consisting of impact and continuous, in a corrosive environment indicate that the composites, containing 0.10 and 0.20 volume fractions of alumina particles (VFAP), have higher corrosive wear rates than the monolith. A graph between the transient current (TC) generated during the impact scratching as a function of solutionizing time at 540°C indicates linear relationship between them. A similar slopes for the composites were observed and the TC values were less for the composite containing lesser VFAP."

Jan 1, 1998

By Asmo Vartiainen

Background of Direct-to-Blister Flash Smelting is discussed; especially slag chemistry relating to copper solubility, slag fluidity and impurity behavior. In December, 2000, Mini-pilot Flash Smelting test runs were carried out at Outokumpu Research Oy to produce blister copper from Chilean concentrate and white metal and from a mixture of them. Tested slag types were iron silicate slag, ferrous calcium silicate slag and calcium ferrite slag with different slag compositions and different concentrate/white metal ratios. The test runs were successful. The fluxing effect of copper oxide was clearly demonstrated and ferrous calcium silicate slags remained fluid on a very wide liquidus range. The distribution of arsenic between ferrous calcium silicate slag and blister copper is much higher than between iron silicate slag and blister copper. This successful test run with the new slag type offer new possibilities in Direct-to-Blister process design.

Jan 1, 2003

By Garth James

Bacterial consortia capable of degrading cyanide and metal-cyanide complexes were obtained from gold mine process waters using enrichment cultures. The cultures contained either cyanide, tetracyanonickelate, or ferrocyanide as a sole nitrogen source. Several bacteria were isolated from the consortia, but none of these organisms were capable of degrading cyanide or cyanide-metal complexes at rates equivalent to those of the intact consortia. The consortium from the cyanide enrichment was capable of completely degrading cyanide from an initial concentration of over 100 ppm in less than one day, when cultured using a fed-batch method. Tetracyanonickelate and ferrocyanide were degraded more slowly. Overall, these results demonstrate that bacteria capable of degrading cyanide and cyanide-metal complexes can be isolated from mine process solutions and are capable of significantly reducing cyanide concentrations under appropriate conditions.

Jan 1, 1998

By Gus Van Weert

This paper describes the results of autoclave testwork where ferric nitrate was hydrolysed in the presence of certain cations and anions and the resulting hematite analyzed for foreign constituents. For the cations Zn++, Ni++, Cu++, and AI+++, selectivity factors of over 107 were found. Magnesium gave 3.106. These factors are calculated as Me/Fe in solution over Me/Fe in the hematite; Me representing the metal in ion added. As-a result of the testwork at Delft University of Technology, BUDELCO (the Netherlands electrolytic zinc producer) ran a series of ferric nitrate hydrolysis tests in the presence of 10 additional trace elements. Impurity levels were prejudiced on Me2 EPHA extraction of iron from their zinc circuit, followed by HNO3 stripping. Good selectivity against base metals was confirmed, but trace elements forming anions (As. Sb) and sulphate were incorporated in the hematite. These BUDELCO results are also presented.

Jan 1, 1995

By T. Kozuka, K. Sassa, S. Asai

"A new atomization process is developed. The principle of this process is completely different from that of conventional processes. This process uses electromagnetic energy induced by direct electric current and direct magnetic field instead of kinetic energy produced by fluid impingement or disk rotation.Experimental work of this process was carried out using pure tin, and it was found that the crucial factor for a stable operation is the contact state of molten metal with the electrode. In order to control the condition, a delay time controlling unit was developed and combined with this process. It is noticed that this controller works well to produce uniformly sized particles.A linear relation between the impulse and the momentum of atomized particles is found by use of experimental data and is explained by theoretical analysis.IntroductionIn atomization processes prevailing in metal powder technology, kinetic energy is currently employed for atomizing molten metal. That is, molten metal is broken into small particles by other fluid (e.g. water, argon gas, etc) or by impinged upon a rotating solid disk. This splashing process is always accompanied with uncertain factors for shape and size of the particles. The diameter distribution of products, therefore, comparatively spreads over a wide range. From another standpoint, the restriction of atmosphere is inevitable in some of these processes. As a pulverizing technology, the process which can produce uniformly sized particles and permits the choice of atmosphere is strongly desired.On the other hand, a great attention has been paid to the spray casting process as a new near net shape casting. In this process, a small size spraying device is favorable."

Jan 1, 1988

By Mohamed Y. Bakr, Aly M. Abdel-Rehim

The present work is related with mechanical activation of processing of Egyptian wolframite by simultaneous ball-milling and pressure alkaline leaching, to improve the recovery of tungsten from wolframite. The results show a total recovery of tungsten from wolframite (97.8- 98.7%) by simultaneous ball–milling and alkaline leaching at temperature 175-200oC. It is concluded that processing of wolframite by simultaneous ball- milling and leaching is mechanically activated and accelerated as a result of the grinding action of steel balls that caused the immediate rupture by continuous removing the product layer of the reaction ( sodium tungstate and iron and manganese hydroxides ) from reacting particle surfaces. This leads to the exposing of fresh and activated wolframite particle surfaces to alkaline leach solution and consequently the acceleration of the reaction of wolframite leaching .The results of the kinetic study 0f alkaline processing of wolframite and its mechanical activation show that the system is under kinetic control.

Jan 1, 2015

By Zongshu Zou, Qiang Li, Mingming Li, Mingxia Feng

The impingement onto the surface of bath by top-blown jets is a significant process characteristic in BOF and EAF steelmaking process. The cavity is one of the most important outcomes of the interaction and plays an important role on reaction kinetics and reactors performance. But to date, the understanding to cavity is still so limited. In present study, a water model for a BOF converter is established and the dimension of cavity profile is investigated. The effects of lance height, gas flow rate, nozzle inclination angle and the amounts of slag are discussed. The results show that penetration depth increases with the increase of gas flow rate and the amount of slag, and the decrease of lance height and nozzle inclination angle. Furthermore, a theoretical model of cavity dimension is proposed for multiply jets impinging liquid bath on the basis of energy balance at the stagnation point of cavity.

Jan 1, 2015

By Masatsugu Morimitsu, Tian Zhang

"This paper presents a novel anode for oxygen evolution in acidic aqueous solutions to produce non-ferrous metals by electrowinning. The method to prepare the anode was thermal decomposition of a precursor solution, and the obtained anode consisted of Ru02-based oxide catalytic layers formed on a titanium substrate, in which the catalytic layer contains nano-oxide particles as the active component. The oxygen evolution potential was lower than amorphous lr02-Ta20s coated titanium anodes so that the cell voltage of electrowinning was further reduced with the amorphous Ru02-based electrode.IntroductionElectrowinning (EW) is used to produce high purity of non-ferrous metals, and the primary metal production of copper, zinc, nickel, and cobalt by EW consumes huge electric energy worldwide, which tends to increase with increasing demand of such metals. The reduction of electric energy consumption is a significant issue for electrowinning industry, which means that the cell voltage reduction is needed to realize more energy-efficient EW processes. Another issue is also indicated from environmental perspectives; i.e., an improvement in EW plant environment by eliminating hazardous byproducts and wastes. Such byproducts and wastes include lead oxide, manganese oxide, and acid mist.We have been developing the anodes for energy-efficient and environmentally friendly electrowinning processes [ 1-11]. The development has been successfully done with the invention of the smart anode, MSA TM (Morimitsu Smart Anode) [ 1-5], which has low polarization for the main reaction and high polarization for the side reaction, in which the main reaction is oxygen or chlorine evolution, while the side reaction is the anodic deposition of each or both of lead oxide, manganese oxide, and cobalt oxide. The anode consists of a valve metal substrate coated with amorphous or less crystalline oxide catalytic layers. One of the typical examples of such oxides is amorphous lr02-Ta20s, and the substrate is normally titanium plate or mesh. The most important point of the oxide is that the amorphization or less crystallinity induce the increase in the active surface area only to the main reaction, not to the side reaction, thereby the polarization of the main reaction being reduced.In this paper, we present the smart anode consisting of RuO2-based catalyst formed on titanium substrates for oxygen evolution in electrowinning. The preparation, characterization, and polarization behaviors of the anodes are shown, and the cell voltage data for zinc or copper electrowinning using the anodes are also presented."

Jan 1, 2012

By S. Aguayo-Salinas, J. L. Valenzuela-García, A. L. Leal-Cruz, M. I. Pech-Canul, M. T. Certucha-Barragán

"The aim of this research was to carry out a comparative and systematic study of the degradation of cyanide by hybrid natural/biodegradation and biodegradation methods using a mixture of Pseudomonas sp and Bacillus megaterium native bacteria. Bioreactors consist of filled columns with contaminated ore containing 100 ppm of total cyanide. In the biodegradation tests a mixture of bacteria was inoculated into the biodegrading solution. Results of cyanide degradation show a similar asymptotic behavior in both the hybrid (opened system) and biodegradation (closed system) methods; however, for the same period of time (72 h) the permissible maximum levels (1-2 ppm of cyanide) are only attained in the closed system. While in the closed system the cyanide levels are reduced from 100 to 1.5 ppm, in the open system, cyanide decreases from 100 to 2.4 ppm.IntroductionOne of the most important tasks of mining industry is the treatment of the wastes generated in mining operations. Accordingly, industrial waste waters and ores represent a complex problem and a great challenge. In addition to ethic and communitarian considerations, there are laws that prohibit or regulate the contamination of water and air. Moreover, they establish that the restoration of wastes must be considered as a necessary operation cost [1]. Currently this important problem is being addressed by the mining and metallurgical industries using different approaches; mainly they are focusing on the treatment of waste waters and ores generated by the leaching process in which cyanide is used as a leaching agent for the recovery of precious metals as gold and silver. Cyanides have toxic characteristics and thus negatively impact the environment when they are discharged to the ground without previous treatment. While there are some processes in current use there are others that have only been proposed and that allow cyanide degradation, transformation to less toxic compounds and/or the complete elimination of cyanide. The second group includes a variety of techniques that use natural, chemical and biological treatments. Natural treatments consist of the passive abandoning of the heap and of its washing with water. Since these processes are slow and generate great volumes of water partially contaminated, then other alternatives should be considered."

Jan 1, 2008