Search Documents

By Tian Sugui

By means of the measurement of the enduring property and microstructure observation, an investigation has been made into the influences of the element Re and TCP phase on the enduring property of the single crystal nickel base superalloys. Results show that the needle-like TCP phase is precipitated along the <110> orientation on {111} planes in Re-containing/free superalloys during the long term aging, the TCP phase is identified as µ phase, and the precipitated µ phase in 4.5%Re alloy is gradually spheroidized during aging. Thereinto, the needle-like µ phase may obviously decrease the enduring lifetimes of the alloys due to the consumption of the refractory elements and the effect of the stress concentration. But the stress concentration is not easily generated in the regions near the spherical-like µ phase, which is a main reason of reducing the enduring lifetime of 4.5%Re alloy to a small extent.

Jan 1, 2010

By Nicola Baldo, Marco Pasetto

"The paper discusses the results of a laboratory study, aimed to evaluate the suitability of the bottom ash from Municipal Solid Waste Incineration (MSWI), obtained from different Italian plants, to be recycled in the lithic skeleton of bituminous mixtures, for base layers of road and airport pavements. The research involved a preliminary study of the physical and geotechnical properties of the bottom ash by itself; it was followed by a mechanical characterization of the bituminous concretes. The traditional Marshall methodology was used to identify the optimum bitumen content; the mixtures were also mechanically checked by means of the stiffness modulus test, repeated load axial test and fatigue test. Because the requisites for acceptance in the Italian Specifications and Standards have been satisfied and given the positive mechanical performances, it has been verified that the MSWI bottom ash can be used as substitution of the lithic materials in the road bases, also with very high contents (up to 81% on the weight of the aggregate). Introduction The incineration of Municipal Solid Wastes (MSWs) provides for by-products which can be mainly classified as bottom ash and fly ash. The first one, corresponding to the 25% on the weight of the wastes to be incinerated, so resulting the principal product of the process, is mainly composed by Silica (Si), Iron (Fe), Calcium (Ca), Aluminium (Al), Sodium (Na) and Potassium (K) oxides, so presenting a composition similar to that of different natural materials. Its metallic fraction can be recovered; the remaining part is usually stocked in dumping or, less frequently, recycled. Bottom ash can be re-utilised in the construction of new infrastructures, especially in bitumen bounded mixtures, because of the inert properties of the binder which covers the grains with a subtle film, that prevents the release of heavy metals. The paper describes a study aimed to design new bituminous mixes for flexible road and airport pavements, realised with the highest content of 4 types of bottom ashes, deriving from different MSWI plants of the Northern Italy. The ashes will be named as BA1, BA2, BA3, BA4 respectively (the origin cannot be specified)."

Jan 1, 2008

By J. C. Pandey

The paper highlights the experimental investigations to characterize texture and plastic strain ratio r-Bar in auto grade steel sheets by ultrasonic measurements, whereas attempts were made to characterize interlamellar spacings in pearlite, tensile stresses and torsional properties in prestressed concrete wires by eddy current measurements. Good correlations were obtained between the testing parameters (such as ultrasonic attenuation and velocity in case of steel sheets as well as eddy current out put voltage and phase angle in case of steel wires) and the materials properties (such as texture, plastic strain ratio r-Bar, interlamellar spacings in pearlite, tensile stresses and torsional properties). 15 MHz normal direct contact and 20 MHz delay line normal shear wave probes were used for ultrasonic measurements. Eddy current measurements were done using an absolute coil probe with variable frequency selection. The experimental results show the possibility of nondestructive on line measurement of the above microstructures and properties.

Jan 1, 2010

By Zhucheng Huang, Yuanbo Zhang, Kecheng Zhang, Guanghui Li, Tao Jiang

"With rapid development of Iron and Steel industry, plenty of metallurgical dusts and sludges are generated, which have not been effectively utilized because of their poor hydrophilicity and bad ballability. Agglomeration and roasting of metallurgical dusts & sludges with a new-type composite binder are studied in this paper. The results indicate that the dosage of the new binders can be decreased to 2.5 wt% from 3.5 wt% when using the wet-grinding process. Under the optimal conditions of briquetting pressure 2070 N/cm2, briquetting moisture content 13 wt%, roasting temperature 1000 °C and roasting time 40 min, the qualities of the green, dry and roasted briquettes meet the requirements of the industry production. The finished products have the compression strength of more than 2000 N/cm2, which can be used as high-quality burdens for blast furnaces.IntroductionWith rapid development of Chinese Iron & Steel industry, there are more and more serious resource shortage and environmental pollution existing. Converter sludges, containing 30% ~ 40 wt% moistures, are typically difficult for recycling [1]. Foreign processing technologies for sludges treatment are relatively advanced including cold-bonded agglomerates for blast furnace, RHF reduction for the dusts and sludges with high content of Zn and Pb, smelting and reduction. Domestic iron and steel companies use a small amount of sludges in sintering. However, the sludges have the characteristics of high moisture and containing harmful impurities, which directly affect the sintering mixture permeability and product quality [2-5]. There are also other technologies such as production of metallized pellets, cooling agents for steelmaking, etc [6]. All of these deficiencies and applied are not in large-scale."

Jan 1, 2011

By C. E. M. Meskers

Electronic and Electric Equipment contains a range of components made of a wide variation of metals, plastics and other substances. Up to 60 elements can be found in complex electronic equipment: base metals, precious metals and special metals in circuit boards and batteries. Because of its amount WEEE represents a considerable metal resource with a higher special and precious metal content than found in ores. The Umicore integrated smelter and refinery recovers and supplies back to the market 17 different metals from EEE. Pre-treated materials enter state of the art, material and energy efficient metallurgical processes for environmentally sound recovery of metals and treatment of off gasses and hazardous substances. The organics in the feed function as reducing agent and alternative energy source during smelting for precious metal recovery. Lithium-ion batteries are treated using a dedicated process. As a result the environmental footprint of metals produced from EEE is much smaller than primary production.

Jan 1, 2009

By K. C. Liddell, B. Dou

"In producing multilayer films for magnetic data storage applications, the interfacial roughness must be controlled in order to obtain high quality materials with reproducible properties. The present understanding of the effect of roughness on multilayer properties such as magnetoresistance is sketchy, particularly for electrodeposited films. In this study, quantitative atomic force microscopy was used to characterize surface morphology before and after Ni films of varying thickness were deposited on Cu cathodes. A multinuclear multilayer growth mechanism is supported by both the deposition conditions and the AFM images, and a multinuclear multilayer model gave a satisfactory fit to measurements of the density of peaks on ultrathin Ni films between 0 and 8 nm thick.Alloys consisting of alternating ferro-and paramagnetic layers have begun to replace Permalloy in the sensing elements of magnetic hard drives. The operating principle of the new read heads is giant magnetoresistance (GMR), and they are smaller and more sensitive than previous inductive heads (1). Experimental studies on sputtered multilayers have emphasized the role of layer thickness and interlayer roughness in determining the presence and size of the GMR effect (e.g., 2,3,4,5,6). However, roughness in electrodeposited multilayers has rarely been measured, even though read heads are likely to continue to be made by this process for some time to come. Cu/Ni can be considered a model system for understanding processing-microstructure-property relationships in electrodeposited multilayers and is the most widely investigated of all such systems (e.g., 7,8,9,10,11,12). Nevertheless, the roughness of the interfaces in Cu/Ni electrodeposits has not been systematically characterized by quantitative techniques, and in all studies reported so far, the total deposit thicknesses were considerably greater than the 10 nm needed for most sensor applications (1). The thinnest such films were about 50 nm (7)."

Jan 1, 1998

By Nathan A. Tiner

Sulfuric acid anodizing process is extensively used in many industrial and consumer products to provide corrosion resistance to aluminum alloys. The anodic coatings produced consist of amorphous alhnum oxide with a pornus structure which is easily sealed and colored with dyes. The coatings may contain defects due to surface flaws, canposition and microstructure of the aluminum alloy, and/or due to the anodizing process conditions. This paper will describe the techniques used in anodizing process, various defects which may be produced in anodic coatings and the methods to control them.

Jan 1, 1992

By S. V. Subramanian

The tool material and the machine design for high speed machining are well advanced over the last decade but the steel design has lagged behind. The paper examines the design of steel in order to control the sliding tribology for high speed machining under dry machining conditions. In high speed machining of steel, accelerated chemical wear of the tool occurs once atomic contact is established at the tool-chip interface, resulting in poor tool life even with high performance tools such as cubic boron nitride. Recent research has confirmed the occurrence of nanocrystalline grains in the interfacial layer of the chip at the tool-chip contact. The volume percentage of grain boundary is increased significantly (10 to 30%) as the nanocrystalline grain size is decreased well below 30 nm. The solubility of tool material into the nanocrystalline grain boundary is two or three orders of magnitude greater than in the crystal lattice. Further the kinetics of diffusion in the grain boundary is seven or eight orders of magnitude greater than in the crystal lattice. Enhanced nanocrystalline grain boundary diffusion occurring in the interfacial layer at the tool-chip contact causes the accelerated chemical wear. Significant improvement in tool life could be achieved by engineering glassy oxide inclusions in steel, designed to self-lubricate the tool-chip interface in-situ at higher cutting speeds. Thus the control of sliding tribological condition at the tool-chip interface is key to suppress nanocrystalline layer formation at the tool-chip contact and hence prevent accelerated chemical tool wear. Sulfide inclusions are designed essentially to promote chip fracture. In addition, sulfide inclusions are designed to act as a diffusion barrier at the tool-chip interface. The application of inclusion engineering concepts to enhance the tool life in high speed machining will be demonstrated with a suitable case history.

Jan 1, 2006

By F. Raupp-Pereira, G. G. Cunto, J. A. Junkes, D. Hotza, V. P. Della

"The present work investigated the valorization of wastes as alternative raw materials for ceramic industries. Different industrial wastes based on the SiO2-Al2O3-CaO system and classified as non-hazardous were selected: sludge from varvite cutting process, sludge from gneiss breaks processes, sludge from filtration/clarification of potable water and a clay classified also as waste. All as-received residues were characterized by X-ray fluorescence, differential thermal analysis, thermogravimetry and particle size distribution. The applicability of these materials in ceramic formulations was then evaluated. The formulated mixtures were subjected to forming by pressing and extrusion followed by thermal treatment. After optimization of the processing conditions, the properties of the samples sintered at different temperatures were also evaluated. The waste materials studied proved to be alternative raw materials to natural mineral resources for the ceramic industry.IntroductionOne of the most important problems that have accompanied the humanity in recent decades is the environment’s degradation. In the same context, the natural resources exploration and technological development are phenomena which, if aren’t controlled, can cause ecological disequilibrium with unpredictable consequences [1]. It is in this perspective that recycling of various wastes assumes relevant importance.The recycling, understood here as the waste process reuse, is a common practice in the First World countries, where the raw materials have strategic aspects and the disposal techniques of solid wastes have considerable economic costs. In Brazil, the ecological conscience begins to be aroused due to, in the last ten years, the implementation of stricter laws for environmental control, in general, and licensing of waste generating from industrial activities, in special. The terms “residue” or “waste” are normally used to describe what remains of a production process; when an application for this material is not found. When wastes or residues are susceptible to be incorporated as raw materials or energy sources in a new material production, they can be understood as by-products [2].The valorization of industrial wastes is important, due to the need to pollute less and give an ecologically correct destination for wastes. The waste recycling, independent of its kind, presents several advantages in relation to using primary natural resources, such as reduction in the volume of raw materials extraction, lower energy consumption, lower levels of pollutant emissions and improvement of the health and safety of the population. The most visible advantage of recycling is the preservation of natural resources, extending its life and reducing the destruction of landscape and ecosystems [3]."

Jan 1, 2008

By Farouk Tedjar

The growth of miniaturization in one hand and energy density need lead to rapid development of new chemistry for batteries as observed during last decade particularly in secondary systems. However dark side of the progress is always in environment impact and scarcity of resources. In the lithium segment a jump from six electrochemical series (all non rechargeable systems) before 1990 to more than 15 systems including new rechargeable systems has been observe during last decade. Lithium battery chemistry was enriched with new electrolytes, conductive salts and new oxide composition. In the same time, lithium ion battery safety was strongly improved during last period. The progress of these technologies was strongly boosted by the substantial growth of the mobile telephone market in the mid 1990&apos;s (+ 1% a month in 2000, and a 71% penetration rate in Europe in 2005 compared to just a few percent in 1996). This market is constantly in search of higher electrochemical performance (mainly energy density in front of increasing miniaturization. Recycling of end of life product could be managed not only in environment aspect, but also under resource conservation and economic aspect of arising technology (mainly on the effect of re-injection recovered materials) The Li-ion segment is a new branch in the cobalt market and impact of LiCoOx will be fitted with the actual increase of the demand for this battery. For this reason all the processes aim to valorize active and packaging material. RECUPYL process project was conducted in this direction to offer a new solution for recycling those lithium systems. The process has been developed at pilot industrial scales using synergy between new equipment (for mechanical pre-treatment step) and existing line at RECUPYL facility (for chemical treatment) and should lead to high valorization rate with a minimum hazardous co-products. The process was also developed in order to be able to recover news cathode materials introduced in electrode like LiFEPO4, LiMxCoyO2 and new anode composition in substitution with former carbon anode.

Jan 1, 2006

Aluminum has experienced significant growth in automotive applications over the last decade as a result of its properties and performance attributes. Looking to the future, the opportunities for continued growth in powertrain and suspension applications plus light weighting of body structures offer the potential for considerable further growth. This represents a growing "energy bank" of aluminum that will become available for recycling at the end of these vehicles' lives. Today, around 90% of the aluminum is recovered and recycled from scrapped vehicles because of its high value relative to other materials. The future growth offers opportunity for new technology and practices, to maximize scrap quality and recycling application. This paper will review the demand for these new technologies and practices and will discuss industry activities being pursued in this area.

Jan 1, 2000

By T. Lezhava

A new reactor model with rotating cathodes has been developed where various forms (dendrite, spongy) of metal depositions and their uninterrupted removal are accomplished by the realization of high current densities and low energy consumption. At the same time in contrast with the existing methods a high quality metal powder may be obtained from concentrated electrolytes without any specific organic or inorganic additives, which allows raising the intensity of the process. The reactor can be used for electrowinning of metals with low adhesive capacity (Pb, Ag, Cu, Zn, Ni, Co, etc.) and the powders. The obtained products may be utilized in general metallurgy as well as in powder metallurgy.

Jan 1, 2006

By Keizo Uematsu, Kumiko Sanda, Nozomu Uchida

"Full understanding of mechanical properties is the most important assignment in ceramics. Establishment of defects-property relationship is crucial for fulfilling the assignment. This study reports detailed characteristics of defects and their relevance to the mechanical properties for alumina ceramics made through a typical industrial processing. Novel characterization methods were applied to evaluate their defects. A very simple direct correlation was successfully found between defects and properties in ceramics. This result is a great epoch in the field of ceramics. IntroductionThe ceramic materials are used in refractoriness, corrosion resistant materials and structural materials. The low fracture toughness and scatter of strength are very important problems in ceramics. The toughness of ceramics is lower than metal and polymer materials, and the allowed defect size is small. Very small internal defects (pore, crack, huge particle) can be a fracture origin in the brittle fracture. The characteristics of defects such as size, distribution and shape change markedly by process condition, which cause the scatter of strength. This study conducts quantitative evaluation and direct observation of the sizes, shape and a number of internal defects with a light microscope, and discusses the relationship for mechanical properties and defect sizes"

Jan 1, 2000

By Robert Fritzsch, Ragnhild E. Aune, Mark William Kennedy, Behzad Mirzaei

"The quantitative particle concentration can give important information about the cleanliness of melts for quality control in primary and secondary production of aluminum. Manual quantification of the particle concentration is normally a time consuming process and human control can bias the acquired images and particle count.The present paper explains the automated image-processing steps for the quantification of SiC-particles, with equivalent diameters from 2 to 25 µm, in solidified A356. A total of 700 micrographs, acquired with a standard white light microscope with 10 x magnification, were analyzed. The applied software (Image Pro-Plus 7.0 from MediaCybemetics®) allows for programming of macros which in tum provides the user with a higher degree of control. The automated results are compared with the results obtained by manually counting the particles in the same micrographs. The impact of the automated results on the estimated filtration efficiency was established to be only -3%.IntroductionInclusions are both indigenous and exogenous particulates that are present in commercial metals such as aluminum. If large individual or large numbers of inclusions are present, they can have a significant negative impact on the appearance, mechanical and chemical behavior of products produced from the metal. Aluminum is known to contain large numbers of inclusions: =50 µm in size, e.g. typically <l ppm by volume or <100,000 inclusions of>20 µm per kg of metal as detectable using a Liquid Metal Cleanliness Analyzer, LiMCA [1]. Depending on the final application of the aluminum, inclusions can render the metal 'not fit for purpose', and result in serious economic consequences to metal producers.It is not surprising that the aluminum industry has developed a number of treatment processes to improve metal cleanliness, given the large number of high value products whose quality can be adversely affected by inclusions. CFFs are the most commonly applied filtration process and have been used to filter >50% of the world production of aluminum since the 1990's [2].Inclusions in aluminum may be particles, bifilms [3] or clusters of: oxides (Al2O3 , SiO2), spinels (MgO· Al2O3), carbides (SiC, Al4C3), nitrides (AlN), borides (TiB2), sulfides, phosphides and intermetallics [ 4]."

Jan 1, 2013

By Alex Probst

With low metal prices and increasing value placed on plant water and tailings disposal areas, it is becoming essential to maximize the efficiency of solid-liquid separation processes. Since its inception over 25 years ago, the use of flocculants has grown exponentially. While flocculants play a crucial role in the sedimentation process, they are also a major operating cost. Recent innovations are revolutionizing the industry once again. New thickener designs are doubling thickener-loading rates while reducing flocculant consumption. The feedwell, as the heart of the thickener, is undergoing many significant metamorphoses. With CFD and other advanced computational analysis, feedwell technology is being examined more thoroughly than ever before, The result is that the thickener previously thought of, as a "Black Box" is now being mapped and controlled with state-of-the-art technology. This paper will examine recent design improvements in all aspects of thickeners in order to project the look of the thickener of tomorrow.

Jan 1, 1999

By Toshiyuki Kozuka

CdTe metal composite semi-conducting material has high potential in good performance of energy conversion efficiency for solar cell and there is much room for improvement of the performance by developing a process of making a thin CdTe film. In this paper, the imposition of intense magnetic field on CdTe electro-depositing surface is proposed, which is one of the possibilities for improving the energy conversion efficiency. In the experiment, cryogen-free super-conducting magnet up to 5T was used and CdTe film was deposited electrically in -o.nv vs. SHE The electrolyte was Cd and Te ammonia alkali solution with controlled temperature in the acrylic cell of 70mm diameter. Electro-deposition behavior of CdTe has affected by the imposition of the intense magnetic field due to microscopic convection in the vicinity of the depositing surface. Electro-deposited surface of CdTe becomes smooth due to microscopic convection around the surface, and the crystallization behavior is also affected, where crystallization temperature and the grain size is changed by the imposition of intense magnetic field.

Jan 1, 2003

By Toshiyuki Kozuka

CdTe metal composite semi-conducting material has high potential in good performance of energy conversion efficiency for solar cell and there is much room for improvement of the performance by developing a process of making a thin CdTe film. In this paper, the imposition of intense magnetic field on CdTe electro-depositing surface is proposed, which is one of the possibilities for improving the energy conversion efficiency. In the experiment, cryogen-free super-conducting magnet up to 5T was used and CdTe film was deposited electrically in -0.72V vs. SHE The electrolyte was Cd and Te ammonia alkali solution with controlled temperature in the acrylic cell of 70mm diameter. Electro-deposition behavior of CdTe has affected by the imposition of the intense magnetic field due to microscopic convection in the vicinity of the depositing surface. Electro-deposited surface of CdTe becomes smooth due to microscopic convection around the surface, and the crystallization behavior is also affected, where crystallization temperature and the grain size is changed by the imposition of intense magnetic field.

Jan 1, 2003

By R. G. Reddy

Industrial copper reverberatory furnace slags were treated by high temperature techniques (sulfide and carbothermic reduction) to recover copper in alloy or matte phase at 1473K. Recovery was investigated for the condi¬tions of varying amounts of metallic sulfide, carbon and CaO additions. The results showed that recovery of copper increased with increasing amounts of carbon addition, and also is strongly dependent on the initial concentration of copper in the slags. Copper recovery for both carbothermic reduction and sulfide treatment were modeled with linear relationships as follows: for carbothermic reduction (%Cu recovery) = 9.0 (%Cu in slag)initial 73.8 and for sulfide (%Cu recovery) = 7.1 (%Cu in slag)initial 82.2 Higher copper recovery was obtained with sulfide treatment than with carbothermic reduction of slags.

Jan 1, 1983

By Helvio Pessanha Guimarães Santafé Jr.

The coir fiber extracted from the husk of the coconut has been extensively used as polymer composite reinforcement in a variety of industrial applications ranging from civil construction to automobile seat cushions. The hydrophilic coir fiber does not act as an effective reinforcement owing to its low interfacial strength with hydrophobic polymers. As a consequence, coir fiber composites display relatively low mechanical strength. The objective of this work was to investigate the effect of an acetylation treatment of the coir fiber surface on the mechanical behavior of epoxy composites with amounts of fibers up to 30% in volume. Coir fibers were immersed in an acid solution of acetic anhydride for one hour, washed and dried, before mixing with DGEBA/TETA epoxy to fabricate the composites. Flexural mechanical properties were obtained by bend tests. The results showed significant differences to similar composites with alkali treated coir fibers that have been previously investigated.

Jan 1, 2010

By Takashi Nakamura

Dismantling and detachment of parts from e-scrap are essential and involve higher cost techniques in pretreatment processes for physical separation. New techniques are desired for effective recycling of minor rare metals, therefore, we are trying to develop new detachment processes such as a new break down process. The principal of this new process is an electrical disintegration by electric pulse. E-scrap is broken down by high voltage electric pulses in water. IC chips and LSI can be detached from printed circuit boards under proper conditions. Ta- capacitors are also broken down to plastic parts and Ta sinter with lead wire. This is very useful in terms of pretreatment for e-scrap recycling. Also in the case of metallurgical production, with its intrinsic potential of smelting, extraction, enrichment and separation methods, play an important role in the context of minor rare metals.

Jan 1, 2015