Search Documents

By D. Q. Cang, G. Duan, H. X. Li, H. Bai

"Life cycle assessment (LCA) is a valid environmental evaluation method and enterprise environmental management tool used in industrial ecology areas. In this paper LCA was newly used to evaluate the environmental impact of manufacturing of alumina by Bayer process in china from two aspects of logistics and energy flow, GaBi software acted as analysis tools with evaluation model established, and several environmental impact assessment criteria were selected based on the actually typical date of Bayer alumina producing process. Evaluation results show that alumina manufacturing by the Bayer process has a great impact on the global warming and human health of respiration, even roasting process gives rise to the greatest impact of winter fog index. Scenario analysis proposed ways of reducing environmental load caused by Bayer process including: (1) the economic and efficient use of mineral processing technology; (2) optimization of energy use, saving power consumption or the use of new more economical source of energy; (3) actively promote the use of innovated technology and equipment in alumina manufacturing and waste such as red mud utilization process.1 IntroductionSince 2002, China is already the world's biggest producer of aluminium, in 2007, China aluminum production has accounted for above 1/3 all over the world, 2009 for 13 million tons and to the end of 2010, China aluminum production is expected increased to be over 15 million ton [1,2,3]. While as the raw material for producing aluminum the alumina production in china has up to 19.46 million tons of the world's total quarter in 2007, by the end of 2009 China alumina production has achieve to 23.78 million tons [4,5]. China has rich bauxite resources with proven reserves about 23 million tons, but the great majority of china bauxite is hard monohydrate diaspore type with low ratio of aluminium silicon, high impurity content and poor aluminum dissolution performance, that cause high energy consumption, long and complex process, high production costs and heavy environment load[6,7]. Before most used alumina production was sintering process rather than Bayer method in china, over the past decade Bayer method has been widely applied instead of sintering process or combination both forming joint process, premise is improving bauxite quality by mineral processing or adding imported rich bauxite mineral[6,8]. In general each ton production of alumina needs bauxite 1.6~2.20t, limestone 0.7~1.7t, soda 0.250kg, fresh water 12.30 cubic meters, in addition to consume large amounts of energy, and emission waste water over 8.0 cubic meters, dust 2.3~5.7 kg, red mud 0.8-1.5 tons. In china Red mud yield nearly 30.0 million tons every year, accumulated stock is approximately 0.2 billion tons, by 2015 accumulative total red mud is expected to reach 0.35 billion tons [9-13].We know aluminium industry and alumina production have produced large waste, make large energy consumption and its environmental impact could not be ignored. Expecting to optimize production processes and achieve resource recycling for this industrial process the proper environmental assessment is very necessary. Currently Life Cycle Assessment (LCA) is generally recognized as the approved tool to achieve the purpose. The essence of LCA tool is to examine, identify and evaluate a kind of materials, product, process, or a system of environmental impact in their whole life cycle. The life cycle of materials or products includes whole process from raw materials obtained to the final disposal, or more ideal with original or other forms of the whole process of recycling [14-17]."

Jan 1, 2011

By R. Kola

Since more than 15 years the Waelz process at "Berzelius" in Duisburg has proved suitable for reprocessing the zinc and lead containing dust and .sludge which inevitably occur in making steel in EAF-plants. The produced Waelz-oxide is agglomerated in a hot-briquetting plant and charged to an Imperial Smelting Shaft Furnace to recover the valuable elements in form of metallic zinc and lead. In view of the actual importance of the dumping problems of the EAF wastes a description of the "Berzelius" treatment route is given but also the situation in Western Europe is illustrated. Dust from stainless steel production is successfully treated in the Scan Dust Plasma Process in order to recycle Chromium and Nickel, while the resulting Zinc-Dust is treated via the Waelz-ISF-Route. For treatment of low Zinc-containing dust, sludge and fines from integrated steelworks, pilot scale tests have been carried out successfully in the Circulating Fluid Bed in order to recover metalized iron and .zinc/lead fume. A 30,000 tpy Demonstration Plant is planned?.

Jan 1, 1990

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

Acid mist generation is a major concern in zinc, copper and nickel electrowinning industries and there is a strong environmental drive to control its emission into the work environment. Foaming reagents are typically added to the electrolyte to alleviate this problem. In zinc electrowinning, Licorice and Saponin are examples of foaming reagents used for this purpose. In order for the foaming reagent to be effective, its foaming behavior must be determined. In this work, a test procedure was developed to study the foaming characteristics of various surfactants for use as foaming agents to control acid mist in aqueous metal electrowinning. This new test was termed as "mini-flotation test" and it was used to study the foaming behavior of a large number of reagents in an industrial zinc sulfate electrolyte under simulated zinc electrowinning conditions (gas sparging). In addition, the influence of important process parameters such as current density, electrolyte temperature, reagent addition level and sulfuric acid concentration on the foaming characteristics of the electrolyte for each surfactant were investigated. The results of this study have identified the most important factors that influence foam formation, growth and stability. This method could be used as a process control for reagent addition in the cellhouse by generating a calibration curve for the optimum electrolyte conditions.

Jan 1, 1997

By Jochen Petersen

Design and operation of heap leach processes are still largely based on,operator experience and rule of thumb. Although considered a low-cost, low-tech route for mineral extraction, the underlying physical, chemical and biological processes are actually rather complex. Numerous heap leach models have been devised over time, but the majority of these tend to simplify the true process and are of limited use in practise. The modelling approach presented here combines the more conventional reaction-diffusion model with models accounting for equilibrium reactions in solution, bacterial growth kinetics, complex reactions schemes, gas flow, heat conservation, etc. One particular model application is discussed in the context of developing a novel high temperature heap leach processes using thermophile micro-organisms. The complexity of processes such as this can only be appreciated with the aid of a systematic model. For the designing engineer an accessible, personal computer based model should be an indispensable tool for the design and optimisation of efficient heap leach operations.

Jan 1, 2002

By Dan Wang, Qian Xu, Guangshi Li, Xionggang Lu, Xingli Zou, Zhongfu Zhou, Hongwei Cheng, Changyuan Lu

The preoxidation of the ore has a profound significance to the concentration, separation and purification of nickel and copper from the lean complex ore. In this paper, the natural Ni-Cu sulfide mineral samples under the elevated temperature condition in air were investigated, as well as under isothermal condition at 600 oC in air. The mineralogical characterization was studied using XRF, ICP and the Rietveld method. The oxidation behavior and the element migration of the Ni-Cu sulfide ore were studied by XRD, SEM-EDS and TG. The XRD Rietveld method was successfully developed in the phase identification and quantification of this complex ore powder sample. The oxidative intermediates (Cu/Ni-ferrite) were detected by XRD, and the process of the element migration was obviously revealed by the line scans using SEM-EDS. It is the preoxidation of this mineral that provides guidance for the extraction of valuable metals from low-grade Ni-Cu sulfide ores in the future.

Jan 1, 2015

By B. Mishra, W. A. Averill

"The application of various hydrometallurgical, pyrometallurgical and electrochemical processes in the extraction, purification and production of radioactive metals as well as the use of various materials, ego metals and alloys, ceramics, polymers, etc. in the process, construction and handling equipment in the nuclear industry has generated a large stockpile of radioactively contaminated waste material and scrap metal which can not be directly discarded, recycled or considered for long-term storage due to its volume and potential hazards, without the separation of radionuclides. This paper reviews the emerging methods that have been investigated and suggested for dealing with some of these wastes and scrap material.The separation technologies studied for the recovery of radioactive components from the pyrometallurgical and electrochemical processing wastes have been discussed in details with results from some of the recent theoretical and physical modeling work as well as the data obtained from the actual waste treatment. Specific processes shall be described in terms of its advantages and limitations. These emerging separation technologies are being considered by the US Department of Energy as alternatives for dealing with the issues of environmental management [EM] and decontamination and decommissioning [D&D].IntroductionThe high temperature carbothermic or metallothermic smelting reduction methods for metal production are associated with the generation of significant quantity of waste as slags, flue dusts, sludges, residues, effluent salts etc. Certain hydrometallurgical processes also generate lots of aqueous waste due to the inherent nature of the technique. Also, the gas-based reduction processes are not applicable to many stable metal compounds, such as alumina, titania, beryllia, lanthanide and actinide oxides, etc. due to thermodynamic considerations. All these methods cause substantial environmental hazard. There is a need to develop alternative processes which have low waste or ideally a ""zero-waste"" generation.Pyrochemical processes using molten salts provide a unique opportunity for the extraction and refining of many reactive and valuable metals either directly from the beneficiated ore (aluminum, beryllium, neodymium, plutonium, uranium, etc.) or from other process effluent that contain reactive metal compounds. The processes reduce metal compounds electrolytically (A12O 3 and BeCI2) on a carbon anode or by calciothermic reduction (Po, Nd). The by-product, in the latter case, is a calcium oxide saturated halide salt. The waste-treatment to recycle the halide has to be done as a separate step or stored as a contaminated waste. A successful separation technology can provide a new insight to the waste minimization strategy for the nuclear industry."

Jan 1, 1996

By A. Mukhopadhyay

Gas stirring, simultaneous arcing, chemical additions are some basic steps in the secondary steel making. From tap to team however, there are enough uncertainties and several in-situ decision making required to match the fmal composition and temperature in the given amount of processing time. Currently available control algorithms rely on overall material and heat balance coupled with a self-learning regression based tuning of model constants. In this paper we demonstrate the capabilities of Computational Fluid Dynamics (CFD) in modeling and analyzing the thermo-chemical aspects of secondary Steelmaking. These models take advantage of scientific and engineering advances in computational tools and provide almost real time speed of analysis. This can be a very effective tool for operator training, process debugging and improvement as well as new innovations. Keywords: Argon purging, Secondary steelmaking, Arcing, Ladle Furnace, Process Control.

Jan 1, 2003

By Ralph H. Nafziger

The Bureau of Mines, in cooperation with the Idaho National Engineering Laboratory, has electroslag melted a V-5Ti-5Cr alloy using a fused CaF2, flux. The alloy is a candidate for use in future fusion reactors. One objective of this research was to evaluate the feasibility of the electroslag melting process in separating simulated radioactive isotopes from the V alloy to demonstrate recyclability. Small amounts of Ca, Y, and Mn were added as surrogates for radioactive isotopes. Results showed that this vanadium alloy can be electroslag melted satisfactorily. The impurities added intentionally were removed or decreased successfully. Among the major alloying constituents, Cr was retained but there were some Ti losses. The latter may be controlled with process refinements. This research suggests that the electroslag melting process could be a suitable method for recycling V alloys after use in future fusion reactors, or for processing other reactive metal alloys with more immediate applications.

Jan 1, 1996

By K. Robinson

Following the longest Smelter campaign in BCL?s history it was planned to completely rebuild the flash smelting furnace in 1987. This was the fourth major overhaul and the most extensive so far attempted. Detailed planning took place over several year$ preceding the shutdown and implementation was completed in 54 days. The key to minimising shutdown time was the method designed for installation of the new uptake shaft and reaction shaft. Major repair work was also undertaken in the waste heat boiler and electric furnaces. Both of these activities had an impact on the critical path of the flash smelting furnace overhaul.

Jan 1, 1993

By Ayşe Ece Yıldızçelik, Mehmet Buğdaycı, Onuralp Yücel

ZrB2 and TiB2 are significant metal borides. They are being used in various industrial areas from space technology to nuclear industry owing to their physical properties such as high melting point, high thermal/electrical conductivity and low density. Present study was conducted in two main stages: self-propagating high-temperature synthesis (SHS) reactions and leaching. ZrO2, TiO2, B2O3 were used as starting material and Mg was used as a reductant to produce ZrB2-TiB2 powders via SHS. Therefore, it was aimed to determine production parameters, leaching conditions and comprehensive examination of final product features. The samples were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques.

Jan 1, 2015

By Ben Hogg

Since the development of the top-submerged lance (TSL) technology for copper and lead smelting by the cooperation of Mount Isa Mines (MIM), now owned by Glencore, and the Commonwealth Scientific Industrial Research Organisation (CSIRO) the core of the ISASMELT™technology has always resided in the lance system. Through continuous innovation and operation of our own smelters, first at MIM, subsequently at Mopani, and also at both the Kazzinc Copper and Kazzinc Lead smelters, Glencore Technology have expanded the core equipment supply to enhance the plant operability. The success of Glencore Technology’s expertise can be directly measured by the success of the Kansanshi Copper Smelter plant, which achieved 100% nameplate capacity within three months of start-up. This paper describes the ISASMELT™ core equipment and how it is applied to smelt sulfide materials. It highlights the strength of the ISASMELT™: continuous innovation to facilitate the versatility and continued increased capacity with every plant implementation.

By Stanko Nikolic

The Top Submerged Lance (TSL) technology, developed in the 1970s, is now widely used for the processing of a range of materials. TSL technology for continuous converting was first patented in the 1990s. The process is based on the use of calcium ferrite slag. Although this slag system had been applied elsewhere the phase equilibria had not been thoroughly investigated. This lead to a collaboration between the Process Technology group of Mount Isa Mines, now part of Glencore, and the Pyrometallurgy Innovation Centre (PYROSEARCH) at The University of Queensland. Through multiple research programs this complex system was successfully investigated. The results were then implemented within thermodynamic modelling tools. This combined new knowledge was then applied to the design and industrial implementation of the TSL continuous converting technology, ISACONVERT™. This paper describes the key findings of the research and how this was applied to the industrial implementation of the technology.

By Zhenbo Zhao

The processes and equipment for INLRFH (Isothermal Normalizing by Utilizing the Residual Forged Heat) of alloy carburizing steel products are presented. It is shown that four key parameters: namely (I) cooling rate before isothermal normalizing, (IT) the lowest cooling temperature before isothermal normalizing, (111) isothermal normalizing temperature and (IV) isothermal normalizing time, should be controlled. The prediction and calculation of these parameters can be achieved on the basis of components treated and the technical requirements of the steel parts by an on-line expert system. The cost-reductions due to the energy savings resulting from implementing this system for automotive parts heat-treatment are most promising.

Jan 1, 1999

By John L. Sundstrom

Complete systems were designed -and are in operation to recycle the effluent streams and to remove impurities from tankhouse. electrolyte, Heavy em¬phasis was placed on making usable products from as many streams as poss¬ible at minimum capital and operating costs. Almost complete recycling: and reuse of water and sulfuric acid were paramount. Techniques used in-clude solvent extraction - electrowinning, evaporation - crystallization and filtration.

Jan 1, 1992

By Gunnar Eriksson

Computer simulation has become an everyday practice in thennodynamic and materials research. Advanced thennochemical algorithms take into account heat transfer effects and salient reaction kinetics when applied for process models. In particular, the combination of mass transfer or overall reaction rates with multi-component Gibbs energy minimisation provides an effective tool for simulation of industrial thennochemical processes and processing of materials. In this work the combination of rate factors with the Gibbs energy technique was studied by using the novel program ChemSheet, which operates through Microsoft's Excel® spreadsheets. Such processes as, for example, CVD of pure silicon production, titania pigment manufacturing, vapour pressure of Mercury in amalgams (in Hg-Iamp manufacturing) and melting behaviour of low-temperature alloys have been modelled. Provided that the thennochemical data is available simulations can be performed with any thennodynamic system. The calculation can be performed as an affinity study without a particular reactor model or with a specific reactor scheme.

Jan 1, 2001

By Batric Pesic

Reactions of metallic iron were studied in several different aqueous solution systems: water, medium salt solution used for the growth of T ferrooxidans, ferric iron solution and solution containing T ferrooxidans. Each system was studied under abiotic and biotic conditions in the presence of T ferrooxidans and as a function of pH, particle size of iron powder, temperature, ferrous and ferric iron concentrations. It was found that metallic iron reacts with water differently than does with ferric iron in water. Surprisingly, T ferrooxidans were non-functional in the dissolution of metallic iron. Also, the reactions of metallic iron with pure water were indistinguishable from the reactions with water containing medium salts for bacterial growth. The reactions with ferric iron were also independent of medium culture compounds. The mechanisms of metallic iron reactions with ferric ions are different from the mechanisms of metallic iron reactions with water.

Jan 1, 2001

By Min Chen, Haohua Deng, Xiaoao Li, Nan Wang, Guangzong Zhang

Grain size and porosity of the produced lime from limestone in early converter slag and the influence of slag temperature in the range of 1300–1400 °C were investigated. The experimental results showed that both the grain size and porosity of the produced lime depended significantly on the slag temperature. After the complete decomposition time of limestone, grain size and porosity changed under the role of CaO grain growth. Grain size evolved sharply with slag temperature, which was illustrated by an analysis on the relationship between grain size and reaction time. Meanwhile, higher porosity was reached at 1400 °C due to the higher concentration gradient of CO2 between the reaction interface and slag bulk. A proposal to obtain the produced lime with finer grain size and higher porosity was given in this paper.

Mar 1, 2018

By Pedro Lobarinhas

In the present work a two dimensional computational model is derived for the description of the time dependent heap leaching process. The flow inside the heap is calculated using the diffusion equations for the flow in porous media. The soil conductivity is also estimated assuming a close packed structure for the grain packing inside the heap. These equations, with appropriate boundary conditions, are solved using a time step splitting scheme. From this calculation the amount of leaching reagent in contact with the ore at any position inside the heap can be calculated and, once coupled with appropriate reaction equations, the amount of metals extracted can be computed and leaching agent concentration updated. The model is tested with available experimental data and the results have shown to be in a very good agreement. The model predicts all the transient features of the data.

Jan 1, 1999

By S. J. Gerdemann

The U.S. Bureau of Mines is studying the kinetics of wet oxidation of sphalerite concen- trate (ZnS) as a possible process for a gravity-pressurized reactor (GPR). At tempera- tures in excess of 200' C, a sphalerite water slurry will react with 0, to form zinc sul- fate (ZnSO,). However, the pressure required to keep the water from boiling at these temperatures has kept this reaction from becoming a viable continuous process. The GPR can easily obtain the high pressures required for this reaction. The reaction rate is complicated by the solubility of 0, in water and the further oxidation of ZnSO, to insoluble zinc oxysulfate (Zn4(OH),S04.4H20). The effects of pressure, temperature, and particle size on the rate of reaction were investigated. Reaction rate was found to be limited by the amount of oxygen in solution. However, at 250" C and 1500 psia, over 90 pct of the zinc was solubilized in less than an hour. The conditions for maxi- mizing the Zn++ in solution, while minimizing oxysulfate formation, are discussed.

Jan 1, 1993

By P Ridgeway, D Xie, M A. Somerville, S Jahanshahi, H Rogers, J G. Mathieson, Y Pan, N Haque, P Zulli, T E. Norgate, L Lu, A Deev

In 2006 the Australian steel industry and CSIRO initiated an R&D program to reduce the industry’s net greenhouse emission by at least 50%. Given that most of the CO2 emissions in steel production occur during the reduction of iron ore to hot metal through use of coal and coke, a key focus of this program has been to substitute these with renewable carbon (charcoal) sourced from sustainable sources such as plantations of biomass species. Another key component of the program has been to recover the waste heat from molten slags and produce a by-product that could be substituted for Portland cement. This paper provides an overview of the low-emission Integrated Steelmaking Process, progress made over the past seven years and the program’s future direction which includes proposed demonstrations of the technologies developed including large scale piloting and full scale plant trials.

Jan 1, 2014