Search Documents

By Pesic. Batric

A novel chitosan-pyridoxal-epichlorohydrin was synthesized and evaluated in our laboratories. The evaluation was achieved by performing kinetic and equilibrium studies of copper sorption. The parameters examined were pH, temperature, concentration of copper, particle size and selectivity of copper sorption against iron, zinc, cadmium and cobalt. It was found that pH was the most important parameter, and sorption of copper increased with pH increase in the range pH 2.5-6.0. The low activation energy of the sorption reaction, 1 1.13 kJ/mole (2.66 Kcal/mole), showed that temperature was not an important parameter. The synthesized chitosan was selective against iron, zinc, cadmium and cobalt. The selectivity with respect to last three metals was achieved by the kinetic difference of sorption, as sorption of copper was much faster than for other metals. Iron (Fe2+) does not adsorb on chitosan. The mechanism governing the sorption of copper is intraparticle diffusion. This finding was supported by the dependance of copper sorption on the square root of time, the low activation energy, and the fit of experimental data in the diffusion through the product layer equation.

Jan 1, 1994

By John A. Herbst

Plantwide control of mineral processing operations has long been sought for its potential benefits. These benefits include minute-to-minute optimization, reacting to disturbances in ore characteristics and equipment status as they happen and the coordination of all unit operations in pursuit of the highest performance level. However several difficult challenges have kept us from fully realizing those benefits. One of these challenges has been to provide fairly complete quantitative descriptions of Unit operations to account for critical interactions within and 'between unit operations. In some cases we understand the physics and chemistry very well and can incorporate that 'knowledge into phenomenological models. In other cases our knowledge is incomplete, so we must rely on other forms of knowledge such as fuzzy logic or neural nets. Another challenge to be met has been to simultaneously compute a large number of manipulated variables. In the past this challenge was met by optimizing only unit-by-unit, rather than on a global basis to significantly reduce the number of variables. In this paper, a procedure that globally optimizes one or two important variables is outlined. This procedure comes much closer to true plantwide optimizing control while remaining computationally feasible. Finally, another major challenge is to choose a meaningful global objective that can be calculated With the models and can be effectively optimized. Financial goals seems to be the objectives of choice. This paper discusses recent progress In overcoming the challenges and illustrates a promising approach which is being pursued at :Mexicana de Cobre's 'La Caridad copper ore concentrator. At M de C, advanced ,control strategies have been 'installed one at a time in the crushing, grinding and flotation sections. During this period, the throughput of La Caridad, Mexico's largest copper concentrator, 'increased from 76;000 tpd to 90,000 tpd. Plantwide integration is expected' to gain an additional 3% improvement in profitability.

Jan 1, 1996

By Gen Kamimura, Hiroyuki Matsuura, Wonjin Choi

Control of non-metallic inclusions in terms of morphology, number density or composition is essential to produce steel products having the desired mechanical properties.Though many studies have been conducted to clarify various properties and evolution mechanisms of inclusions at steelmaking temperature, it has been reported that the states of inclusions in final products are significantly different from those in crude steels for some steel grades. The present study has focused on the evolution of oxide and nitride inclusions in solid Fe–Al–Ti–N alloys during heating to increase the understanding of inclusion evolution in a simplified metal system. Compositional and morphological change of initial inclusions, as well as precipitation and growth of new inclusions have been observed even when the alloy was in a solid state.This behavior has been observed due to the change of thermodynamic stability and solubility of existing phases in inclusions.

Mar 1, 2017

By Subagyo

The condition of slag in a pyrometallurgical reactor is vital to ensuring control of the process. A new technique based on multivariate image analysis (MIA) of digital images has been developed to provide an online measurement of important slag characteristics, such as the presence of exposed metal, the presence of solid phases, and temperature. This paper shall describe the technique and provide some results from analysis using industrial plant data.

Jan 1, 2003

By E. J. Peuraniemi

Oxidation of chalcopyrite concentrate and two low-iron copper mattes were studied using a laboratory scale laminar-flow furnace simulating the phenomena taking place in different zones of the reaction shaft of a flash smelting furnace. In the experiments, screened fractions were fed into the furnace and sampled after short reaction time intervals by quenching them into a water film. Experimental conditions included temperatures of 1100 and 1300°C with reaction gas oxygen contents from 21 to 75 vol.%. Samples were analysed chemically for Cu, Fe and S to define removal rate of sulphur. Optical and scanning electron microscopy with EDS-analyser were used to examine the samples. In this paper, oxidation kinetics as well as ignition of particles are discussed. Changes in particle morphology, size, and composition are viewed to closely define the proceeding of the oxidation, and, consequently, to compose a detailed model of dust formation and reaction mechanisms. Data obtained in the experiments broadens the knowledge of physical and chemical phenomena in flash reactions and serves as reference for computer simulations.

Jan 1, 2000

By Batric Pesic

The interactions of mineral-pyrite with T. ferrooxidans were studied by using a cyclic voltametry technique. The interactions with bacteria were examined during the entire growth stage of bacteria (fermentation), The pyrite ?surface invariably drastically changed ' its. properties at the second day of fermentation. Beyond two .. days of fermentation, the cyclic voltamograms were insensitive to convective diffusion produced by stirring. The product layer was examined by SEM,. X-ray diffraction and chemical analysis. The SEM study revealed that bacteria populated the pyrite surface at an extremely high density levels. The high density of bacteria, and the solid reaction products formed on the pyrite surface created conditions for pore diffusion which explained why the CVs became .insensitive to convective diffusion in solution (stirring). The x-r:ay diffraction study confirmed jarosite as a product layer. A mechanism of T. ferrooxidans cells serving as nucleation sites for jiarosite formation is proposed.

Jan 1, 1991

By Maria Rashidi, Maryam Ghodrat, Bijan Samali

Treatment of sharp medical waste (waste disposable syringes) produced in hospitals or health care facilities in an environmentally sound ways have raised concerns relating to public health and occupational safety. Life cycle assessment (LCA) is a decision-supporting tool in waste management practice; but relatively little research has been done on the evaluation of sharp medical waste treatment from a life cycle perspective. Our study assesses the environmental performances of medical waste incineration as a type of dominant technology for specific medical waste of average composition. Inventory models were used for waste incineration and residues land fill. Background data were derived from modelling performed in HSC Chemistry thermochemical package linked with GaBi environmental assessment tool. Two scenarios have been considered and compared: Waste disposable syringes partially replacing coke in Electric Arc Furnace (EAF) steelmaking (WSI) and conventional incineration with pure metallurgical coke without adding waste syringes (CI). The results of this study could support the medical waste hierarchy and indicate that from a life cycle perspective, replacing part of metallurgical coke with waste syringes in electric arc furnace steelmaking leads to fairly significant reduce in most of environmental impact categories.

Mar 1, 2017

By Maneesh Singh

During the various stages of iron & steel production a number of iron-rich by-products are generated. The traditional way to recycle them back to the blast furnace has been the balling - sintering process. These by-products can also be made into cement-bonded agglomerates for use as burden material for blast furnaces. In order to improve the quality of agglomerates the effects of various processing parameters on the properties of cement-bonded briquettes have to be controlled. This paper looks into the various aspects of producing cement-bonded agglomerates and using them as burden material for blast furnaces.

Jan 1, 2003

By Truan-Sheng Lui, Li-Hui Chen, Hao-Wen Hsueh, Fei-Yi Hung

"Since Ag wires have similar hardness and bonding properties to Au wires, they can be applied in some pads. In the present study, the annealing effect (at 225°C~275°C for 30min) on the tensile mechanical properties of silver wires with f=23µm was investigated. In addition, the micro-structural characteristics and the mechanical properties before and after an electric flame-off (EFO) process were also studied. Experimental results indicate that with annealing temperatures of more than 250°C, the silver wires possessed a fully annealed structure, the tensile strength and the hardness decreased, and the elongation was raised significantly. Under the thermal effect of EFO, the necks of the Ag balls underwent recrystallization and grain growth was induced, and the annealed Ag wires had a shorter zone of HAZ (220µm). The bonding strength and the neck-strength of the Ag wires were more than 7gf and possessed excellent bonding properties.IntroductionThermosonic ball bonding is one of the preferred processes for electronic packaging to connect a semiconductor chip and a lead frame by a thin metal wire. At present, gold wire and copper wire are the preferred interconnect materials to bond with the aluminum metallized wafer pads [1, 2]. Since gold is expensive and the reliability of copper is poorer [3], the study of silver wire has attracted a lot of attention already. In addition, the inherent properties of high ductility and low hardness of silver as well as its workability effectiveness compared to gold, have made it a preferred alternative .[4, 5]"

Jan 1, 2012

By Yongbin Yang, Meixia Cai, Yufeng Guo, Guanzhou Qiu, Tao Jiang, Jianjun Fan

"A series of sintering and metallurgical experiments were carried out to optimize the blast furnace burden structure in this study. The results indicated that the sinter disintegrated seriously with basicity around 1.4, and after this “turning point”, the sintering properties were improved gradually with the increase of basicity of sinter. Based on the results, an idea was put forward which focused on producing two different kinds of sinter with different basicity. Different with the original burden structure of 85% sinter with basicity 1.4-1.5 + 15% pellets, an alternative new BF burden structure was proposed by the following structure?44% sinter with basicity 1.05 + 44% sinter with basicity 1.87 + 12% pellets. This new alternative BF burden structure has been adopted by some steel plants.IntroductionIn recent years, conventional blast furnace (BF) process was put into operation to produce hot metal in “A” steel plant. “A” steel plant owns two sets of sinter strands at present. Because the sinter production capacity exceeds the actual requirements of BF, a burden structure with 85-90% self-made sinter + 10-15% purchased pellets is adopted to take advantage of the low–cost sinter. But the serious problems encountered with the BF operators are that the sinter disintegrated easily during transportation and storage process. Therefore, the rate of return fines is very high after sinter being screened."

Jan 1, 2012

By Roy J. M. van Lier

In industrial aqueous solutions, germanium generally occurs in trace amounts amid high concentrations of other metals, such as zinc, copper and iron. Separation of germanium from these metals as well as its isolation from gallium and indium pose a real challenge to the hydrometallurgist. After a brief discussion of the aqueous chemistry of germanium, this paper reviews the flowsheet of the Apex Mine in Utah. The Apex property was the only mine in the world to be operated primarily for production of gallium and germanium, but apparently closed due to great operating difficulties. Several process variants proposed for the treatment of the Apex ore, including bioleaching methods, are addressed. Following a more general description of the behavior of germanium in hydrometallurgical zinc processing streams, available technology for its recovery from aqueous solutions is summarized. Precipitation, solvent extraction, ion exchange, electrowinning, ion flotation and liquid-membrane separation are all outlined in terms of the aqueous chemistry of germanium. Finally, the production of high purity germanium dioxide and metal is briefly discussed

Jan 1, 1995

By Andreas Dietrich

Laser off-gas measurement of CO, O2 and temperature has been carried online in EAFs. A visualization screen shows the values of CO and Oxygen and temperature for the entire heat, and includes the status of furnace equipment. The historical data of the heats are stored such that the furnace performance can be evaluated and optimized. A short comparison between laser based and conventional systems has been carried out related to speed, influence of dust, water, pressure, protection for bag house explosions. A high water and/or dust content in the sample does not represent a problem for this type of system. The measurement method works without interruption even under worst conditions such as dirty scrap, carbon injection etc. The installation was developed in conjunction with Marienhuette, Graz. They are 100% scrap based with a tap to tap time of ca. 46 min. Keywords: Laser Measurement, Off Gas, CO, O2, Temperature

Jan 1, 2003

By Carl C. Nesbitt

A study was conducted to investigate the claims of early observers who noted an increase in the rate of gold dissolution when chlorine was chemically produced in the leach vessel compared to sparging with chlorine gas. This "nascent" chlorine was presumed to be an active intermediate in the production of chlorine (C1,l from chloride ions. The study used UV light to produce an activated chlorine atom intended to recreate the observed increase in the gold dissolution rate. Although no change in the kinetic rate was observed, the reaction mechanism by which chlorine reacts with particulate gold was instead determined. Various concentrations of multivalent cationic chloride salts were added to the leach solution to demonstrate that the increased dissolution rate was due to the increased concentration of the chloride ion and ionic strength of the solution.

Jan 1, 1992

By M. del C. Ruiz

The extraction of Nb and Ta from a columbo-tantalite of San Luis, Argentina, is being studied by using a pressure reactor and HF as leaching agent. The reagents and products have been characterized by several techniques such as scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDXS), X-ray fluorescence (XRF), X-ray difracction (XRD), surface area (BET) and size particle analysis. Experimental results have shown that the extraction of niobium and tantalum increases with increasing temperature, reaction time and acid concentration. For particle size between +80 and -355 mesh no significant changes are detected. It is also slightly affected by the stimng speed. XRD analysis of the residues did not show formation of new crystalline structures.

Jan 1, 1999

By Husamuddin Ahmadzai

A survey of regulations and state of the art control technologies is presented relating to the smelting of primary aluminium, copper and recycling of residues. Some costs associated with the alternatives and trends for the coming decade in this. sector are identified.

Jan 1, 1992

By Bror Nyrnan

Solvent extraction technology and equipment have been developed within Outokumpu since the early seventies. During this period altogether nine solvent extraction processes for molybdenium, zinc, rhenium, cobalt, nickel, calcium and magnesium have been commercially adopted in Outokumpu's metallurgical plants. During last years a new mixer-settler concept based on a "Vertical Smooth Flow" (VSF) principle has been developed. It has also been found to be a good method for copper solvent extraction, decreasing essentially the crud formation and the organic and aqueous entrainments.

Jan 1, 1994

By Alexander Burns

Electrolytic salt splitting is a technology where acid and/or base is regenerated from a neutral salt using membrane electrolysis. Recent advances in the understanding of brine treatment, membrane stability, and cell design have made electrolytic salt splitting feasible on certain hydrometallurgical solutions. Meanwhile, environmental regulations have made the bulk disposal of salt solutions more difficult. In this paper, sodium sulfate salt splitting is examined from a cost perspective, compared to purchasing the reagents directly. Relative costs are estimated for several regions based on published electricity and reagent prices. The results show that salt splitting is economically favourable in some regions, and can be made more favourable by applying modifications to the traditional three-compartment desig

By Cong Wang, Kexin Jiao, Yongan Zhao, Haibin Zuo, Jianliang Zhang

Traditional refractory materials for blast furnace hearth lining are mainly composed of carbon bricks and the ceramic cup. However, these materials can’t meet the demands for long service life design of blast furnaces. In this paper, a new refractory called carbon composite brick (CCB) was introduced, which combined the advantages of carbon bricks and the ceramic cup. In this case, the resistance of the CCB against corrosion was equal to the ceramic cup and the thermal conductivity of the CCB was equal to carbon bricks. From the results of more than 20 blast furnaces, the CCB could be well used in small blast furnaces and large blast furnaces. In the bad condition of low grade burden and high smelting intensity, the CCB gave full play to the role of cooling system, and effectively resisted the erosion of hot metal to improve the service life of blast furnaces.

Jan 1, 2015

By M. Z. Sukiennik

A static method for vapor pressure measurement up to 1450 K and above 1 hPa is presented. The method is designed for equilibrium and kinetic studies of metallic systems, including those with a chemical reaction. Application examples are given for determination of activities in condensed phases, and heterogeneous reaction rates and equilibrium constants.

Jan 1, 1993

By P. J. Uggowitzer, H. Kaufmann

"New Rheocasting is a novel route of semi-solid casting, in which the globular semi-solid precursor material is produced by controlled cooling of only slightly superheated melts in conventional steel crucibles. The resulting semi-solid slugs are placed into the sleeve of a vertical Squeeze Casting Machine and then filled into steel dies. Solidification occurs under hydraulic pressures up to 100 MPa Due to the reduced cost of precursor material, reduced investment cost and easier recycling, the New Rheocasting process offers cost reductions of up to 25% over conventional semi-solid casting · routes. The New Rheocast products are pore free, pressure tight, weldable and heat treatable castings.In the present work the New Rheocasting Process is introduced and the influence of heat treatment on mechanical properties of the New Rheocast alloy A356 is discussed.The alloy A356 is cast under ideal New Rheocasting conditions into a step die on an UBE HVSC 350 Squeeze Casting machine. As-east, TS and T6 heat treatment conditions with variations in solutionizing and aging time/temperature parameters are applied and the samples are tested by tensile testing. Alternatively, the same heat treatment conditions are applied to conventional Squeeze Casting parts and compared with New Rheocasting.Questions of potential cost savings due to modified heat treatment conditions are also addressed in this paper."

Jan 1, 2000