Search Documents

By Miao Tian

Large quantities of copper complex resources are produced globally and urgent to be cleanly processed. This article presents a thermodynamic analysis of mixed smelting process including low-grade polymetallic copper sulfide concentrates, high copper content sulfide concentrates, metallurgical by-products (copper removal slag from lead metallurgy), and copper powder from electronic waste. A top blown smelting reactor to simulate mixed smelting process is developed using a metallurgical process simulator, METSIM. Reactor parameters, heat loss and phase distributions are estimated from actual plant data. The proper proportion between complicated primary and secondary copper resources is determined by analyzing the influence of the feed rates of various resources, oxygen, silica flux and revert on the smelting performance. Autogenous smelting process is built by optimized matching materials of copper complex resources, in terms of the reactor temperature, copper content in matte and slag, and the percentage of magnetite in slag.

By Yan Zeng

Lithium metal silicates (Li2MSiO4, M = Fe or Mn) composed of abundant and non-toxic elements are important cathode materials for Li-ion batteries (LIB). In contrast to solid-state or sol-gel methods, hydrothermal synthesis conducted in pressure reactors is a favorable processing route as it provides the potential for scalable production and is environmentally benign. However, the key is to control the precipitation reaction to obtain powders with desired properties to meet battery specifications. Through a systematic study, we have found that Li2MSiO4 with tunable size from 300 nm to 1.5 μm can be produced by adjusting precursor concentrations, temperature, and reaction time. Under optimum conditions, high purity Li2MSiO4 with minimum defects were successfully produced and examined as an LIB cathode. The use of complexing agents promoted the formation of unique hollow particles via the self-assembling of elongated crystals. A four-step formation mechanism is proposed based on extensive characterizations with XRD, HR-TEM, SEM, and Mössbauer spectroscopy.

By James C. Withers

There is no production of rare earth metals in the U.S. in spite that the U.S. is the largest consumer of rare earths in some form that includes consumer and Department of Defense (DoD) devices. The one U.S. mine has been purchased by the Chinese that even enhances their monopoly on rare earths. A research effort has demonstrated rare earth oxides can be extracted from bastnaesite ore as well as coal ash at efficiencies in the upper 90s percent. The rare earth oxide can be carbothermically treated to produce an oxycarbide which is highly electrically conductive. The rare earth oxycarbide can be used as an anode in anhydrous fused salts electrolysis to produce a highly purified rare earth powdered metal. It is also possible to electrofractionate the individual metals which can be combined with co-deposition of iron and boron to produce the highly magnetic alloy Nd2Fe14B.

Mar 1, 2018

By Wankun Wang, Fuchun Wang

Based on the study of artificial neural network, the neural model was established for the prediction of germanium extraction from zinc oxide dust by microwave alkaline roasting-water leaching. Alkali-material mass ratio, microwave heating temperature, liquid-solid ratio, aging time, leaching time and leaching temperature were the significant factors for the process. The results indicated that the neural network prediction model was reliable, and the forecast values fitted well with the actual experimental values. The model could be used to predict the regeneration experiments with high credibility and practical significance. The accuracy of convergence of the model reached 10−5.

Mar 1, 2018

By J. L. Hill, M. A. R. Sharif, J. Lin

"A numerical algorithm has been developed to simulate the movement, breakup, and entrapment of the oxide film inclusions encountered during the mold-filling processes of aluminum castings. The flowfield is solved using the well-known Marker and Cell (MAC) method by a time marching process. The Volume of Fluid (VOF) method is used to track the free surface boundaries. A kinematic approach is employed to track the movement and breakup of the oxide films on the free surface or in the bulk liquid metal. The computer program based on the proposed algorithm is able to model the flow behavior and oxide film movement, breakup, and entrapment in mold cavities for aluminum castings.IntroductionMetallographic and fractographic studies of the aluminum castings show tangled networks of oxide films in the castings. These oxide films can form in the furnaces or during the mold filling processes. Green and Campbell [I] concluded that the oxide film defects dominate the strength of aluminum castings. The main cause of oxide film entrapment into the bulk molten metal during the casting processes is the surface turbulence. In film-forming alloys, if the surface breaks, due to a drop, a fountain, or a breaking wave, then the surface film is folded over and incorporated into the bulk liquid. The incorporation of surface films leads to cracks in the casting and other defects that are nucleated by the presence of the folded films, such as porosity and hot tears. Campbell [2] estimated that up to 80% of scrap in light-alloy casting is the result of surface turbulence."

Jan 1, 1999

By Gordon A. Irons, Diancai Guo

"Uneven movement of scrap during melting in an Electric Arc Furnace causes operation problems: cave-ins interrupt electric power input. The movement also influences the radiation heat loss to water-cooled side panels and roof. An apparatus has been built to simulate the flow of scrap that may be interlocked. It has been observed that flow starts at the point where the suspended length of the pile bottom reaches the average scrap size, and proceeds in the form of cave-ins, but scrap pieces slide with each other as ordinary granules. After a cave-in, the pile angle usually remains much larger than the normally observed angle of repose. The force balance of a partially suspended scrap pile has been analyzed, and the equivalent cohesion due to interlocking estimated. A numerical model has been developed to simulate the scrap flow. Simulated results agree reasonably with observed phenomena.IntroductionWhen one considers the melting of steel scrap in an electric arc furnace (EAF), it is helpful to understand the movement of the material during meltdown. As industrial experience demonstrates, scrap movement greatly affects EAF operation. In a typical operation, scrap is dropped into the furnace from scrap buckets. The roof and electrodes are swung into position, and power is applied to the electrodes situated over the scrap. The electrodes ""bore"" into the scrap by melting into the steel in the immediate vicinity of the electrodes as they are lowered. If solid scrap pieces gradually slide towards the arc area, the electric power supply can be maintained at a high level, with few interruptions or drastic electrode adjustments. This results in a high production rate and low power consumption per tonne of steel produced. On the other hand, if the charge moves down unevenly, i.e. in large surges, usually called cave-ins, the electrodes must be drastically raised, and power supply frequently interrupted. This is also accompanied by a high level of harmonics induced in the power network, deteriorating the quality of electricity supplied to other users.In addition, the movement of scrap in an EAF also influences the furnace heat efficiency, as the scrap pile is much closer to the electric arcs compared to the furnace wall and roof, and absorbs more radiated heat. Early exposure of the wall and roof to the arcs will increase the heat loss due to radiation, and reduce the service life of the furnace."

Jan 1, 2004

By H. Deveci

Bioleaching/biooxidation is essentially a dissolution process with the involvement of acidophilic bacteria acting as the "catalyst" to accelerate the dissolution of metals from sulfide minerals. The contribution of bacteria to the metal dissolution is closely controlled by the growth of bacteria, which is itself affected by the physico-chemical conditions within the bioleaching environment. There are a number of operating parameters controlling bioleaching processes, which are required to be maintained within a certain range in the leaching environment whereby the activity of bacteria with the resultant oxidation of sulfide minerals can be optimized. In this regard temperature, acidity, oxidizing conditions, availability of nutrients, oxygen and carbon dioxide, surface area and presence of toxic ions are of prime importance for control and optimization of bioleaching of sulfide ores/concentrates. Bioleaching processes are temperature and pH dependent with optimum metal dissolution occurring in a particular range where the bacterial strain is most active e.g. mesophiles at 35-40°C and pH 1.6-2.0. Provision of nutrient salts is required to maintain the optimnm growth and hence metal dissolution with the quantity of nutrients apparently being dependent on the availability of substrate i.e. head grade/pulp density of an ore/concentrate. Oxygen transfer is one of the most critical factors since the oxygen levels below 1-2 mgll may adversely affect the oxidizing activity of bacteria. Bioleaching rate tends to improve with increasing the surface area at low pulp densities but, in practice. the pulp density is limited to -20010 w/v. Increasing concentrations of ions such as cr may also adversely affect the oxidative activity of bacteria. Keywords: Bioleaching, Biooxidation, Acidophilic bacteria

Jan 1, 2003

By Sunil G. Warrier

A rapid infrared forming technique has been developed to fabricate titanium matrix composites. This technique applies infrared heating to infiltrate titanium alloys into carbon and silicon carbide prepregs. The entire process typically takes 1-2 minutes in an inert atmosphere. The advantages of this technique are that the process is fast, simple, does not require a vacuum or a high external pressure. The process is very economical both in energy conservation and operation costs. This technique has been used to produce void free composites with limited, well controlled fiber-matrix reactions and mechanical properties comparable to currently available titanium matrix composites.

Jan 1, 1993

By Corby G. Anderson

Antimony has been utilized by mankind for thousands of years. However, due to recent environmental concerns, antimony is often considered to be an impurity element, Since antimnoy is commonly found in precious metal refractory ore bodies, extraction is essential. The Sunshine Mine in Kellogg, Idaho has recovered antimony from its precious metal tetrahedrite deposits since the 1940's. A plant was initially constructed as a primary antimony source during World War II. This facility also decreased the downstream smelting penalty for the silver copper-lead concentrate and provided an industrial commodity from a potential environmental nuisance.' This paper describes the Sunshine antimony processing- facility. Specifically, the relevant process chemistries involved in concentrate leaching, metal electrowinning, and sodium antimonate production will be discussed. In addition, ongoing areas of research to improve unit operations and treatments implemented to meet environmental' discharge requirements will be covered.

Jan 1, 1992

By Dietrich Gross

This paper describes an advanced oxy-fuel combustion technology for re-melting aluminum that significantly reduces energy consumption and emissions. This oxy-fuel combustion technology developed by Jupiter Oxygen is a patented process for combustion of fossil fuels with pure oxygen while excluding air, thereby creating an undiluted high flame temperature and increased efficiency for process heating in industrial furnaces. This unique process has led to improved heat transfer and longer residence time while maintaining the same process temperatures as with air combustion. The energy efficient combustion process allows aluminum companies to operate at a substantially lower cost due to a dramatic fuel savings of up to 70% for natural gas and waste oil (1). The results of more than 10 years of day-to-day experience utilizing the Jupiter Oxygen Corporation oxy-fuel combustion technology licensed to Jupiter Aluminum Corporation in the aluminum re-melting business are discussed.

Jan 1, 2008

By F. Kongoli

Viscosity is an important parameter of copper smelting and converting processes. It affects the settling of matte or metal droplets in the slag, distribution of elements etc. Despite this importance, confusion exists on the viscosity of copper smelting slags as a result of disagreements found among the measured viscosity data of several authors especially in the slags of high ferric iron content and close to magnetite precipitation. In this work a critical review of the existing data on the viscosity of copper smelting slags has been first carried out and the effect of oxygen potential on the viscosity of copper smelting slags has been clarified through a coupled quantification of viscosity and liquidus temperature. The confusion in the literature has been clarified and the importance of the relation between the viscosity and the liquidus temperature is discussed.

Jan 1, 2003

By R. W. Bartlett

A two step process for treating platinum group metal flotation concentrates Is described while experimental results. The process was designed to be simple and Inexpensive While yielding a high recovery and fast turnaround. Ii consists of electric furnace smelting of concentrate to remove gangue and produce a homogeneous sulfide matte containing all of the base metals and platinum group metals. Sulfide oxidation Is minimized during smelting to avoid Installing an acid plant In the second step, matte Is pressure-leached with oxygen In an acid sulfate system to dissolve Iron, nickel, ?and copper while leaving a residue highly concentrated In precious metals, and typically about 1% of the flotation concentrate mass, A batch process with oxygen titration against the base metal composition of the feed Is used to control the end point of the leach. Sulfides must be eliminated while minimizing the precipitation of hydrolysis products. The leach residue can be smelled to bullion to facilitate sampling accuracy.

Jan 1, 1989

By Liangying Wen, Feng Xia, Chenguang Bai

"The situation of the Ti-V-Magnetite samples reduced with microwave has been investigated in laboratory. Firstly, the paper focuses on the heating behaviors of vanadium-titanium magnetite and characteristics of carbothermic reduction of V-Ti-magnetite in the microwave field. The effect of concentrate's size, quality on heating behaviors and reduction processes were researched. Results show that microwave heating may be a new heating resource replace of carbonic combustion reaction in reducing reaction. When the allocation of carbon is (16.7-30)%, carbothermic reduction of V-Ti-magnetite in the microwave field can proceed; with the increasing of carbon mixed, the metallization rate increases; and Fe, V can be reduced from their oxides in the microwave field; Titanic low oxide can be reduced from TiO2.1. IntroductionThe resource of Ti-V-Magnetite is abundant in the western area of Panzhihua in China, so far a mineral deposit of 4.64 billion tons have been proved up, it contains 14.75 million tons of V2O S which accounted for 87% of the vanadium and 5.93 hundred million tons of TiO2 accounted for 94% of the titanium resource respectively in China. The previous study proved that the major composition of mineral of the Ti-V-magnetite are Ti-magnetite, limonite, iron spinel, magnesium spinel etc, and the main elements of the Ti-V-magnetite in this area are Fe, Ti, V, Cr, Co, Ni, Ga, Sc etc[1] Due to the restrict of the BF-BOF process technical, during the smelting of the iron, the level of extracting the vanadium, titanium as well as other metal elements is limited. This results serious wasting of resources. To develop a new reduction process of Ti-V-magnetite is on the agenda, the microwave assistant reduction could meets this need, based on its characteristic of easy controlling of heating rate. To make use of the microwave energy to substitute the released heat sources of carbon combustion with air, use the solid phase state reduction at a relative lower temperature, make the beneficial element in Ti-V-magnetite transferred into the metal phase, then separated from the impurity. It is well worth to point out that once the microwave based reduction method has its industrial scale, it will take an outstanding position by its less release of carbon dioxide. This new environment-friendly process will play a vital role in the development of social industry and economy."

Jan 1, 2008

By Bob Hannah, Peter C. Hayes

The changes that are happening in the world of metallurgy, and with it university education, are generational and require generational responses. Some of the key issues facing metallurgical education and ongoing professional training are explored. What will be required of metallurgical engineering professionals in the coming decades? What knowledge and skills will be needed? How to provide the educational and learning pathways, and how to attract smart young people into this profession? These are issues more readily addressed by tertiary institutions in conjunction with industry; perhaps the greater challenges lie in building and maintaining competencies post-graduation. There is a need to establish and maintain a system that supports graduates and enables them to develop further into competent expert engineers able to successfully address complex engineering challenges.

Jan 1, 2014

By Zhou Shu-cai

"A method has been proposed for the pre-treatment of high phosphorus iron ore by carbothermic reduction assisted with microwave irradiation and magnetic separation on a laboratory scale. Chemical analysis of the reduced ore sample, the metal sample and the slag sample were conducted. Based on the above research, the influences of carbon addition, microwave power and microwave irradiation time on the recovery of Fe and dephosphorization were discussed. It indicated that the increase of microwave irradiation time and power had substantial effect on the recovery of Fe while the influence of carbon addition was not obvious and the highest iron recovery ratio reaches some 95.5% when the dephosphorization ratio was 37.68%. A high iron recovery ratio and a reasonable dephosphorization rate were incompatible under the conditions investigated in this study due to the reduced iron and because unreduced P-contained gangues were not efficiently separated. This method may provide a reference for the future utilisation of high-phosphorus iron ore.IntroductionWith the rapid growth of crude steel production in China, the source of iron ore tends to become increasingly strained and is facing the risks of raw material shortage for the iron and steel industry. In order to decrease the production cost, China has to focus on the utilization of its domestic low grade iron ores for the iron and steel plants [1-2]. China has a large deposit of high phosphorous iron ore with a reserve of 7.45 billion tons which is unused in any large scale [3]. Therefore, the development of a successful and economically viable technology for high phosphorus iron ore is of profound importance. To remove phosphorus from the high phosphorus iron ore, several mineral and metallurgical processes have been proposed, such as bio-leaching [4], roasting reduction plus melting separation [5], pre-reduction and screening methods combined with mechanical crushing or air jet milling[6] selective agglomeration plus reverse flotation [7]. However these processes are not cost effective or are time consuming. The traditional pyrometallurgical process( BF+ BOF) refuse this kind of ore mainly because that molten iron is saturated with carbon or high carbon content and thus all phosphor us in the burden goes to the molten iron[8]. Therefore, it is important to exploit the cheap and abundant high phosphorus iron ore as a resource in ironmaking. In recent years, the microwave was widely introduced as a heat resource for extractive metallurgy of iron ore or other minerals. For example, microwave assisted ore milling, microwave assisted carbothermic reduction of metal oxides and microwave assisted mineral leaching issues[9-10]"

Jan 1, 2014

By Camila Martini Matos, Maria das Graças da Silva Valenzuela, Francisco Rolando Valenzuela Diaz, Lucy Gomes de Sant' Anna, Orley de Oliveira Magalhães, Flavio M. S. Carvalho, Isaac Jamil Sayeg

"Kaolin clays are widely used in various industry segments. Its main properties are fine granulometry, chemical inertness and whiteness. In general, kaolins are not easily organophiilized as a result of its 1: 1 structure. The aim of this paper is to describe the modification of a Brazilian kaolin sample, in order to obtain an organophilic kaolin of high performance. The clay as received was identified by X-ray diffraction and characterized by optical microscopy, cation exchange capacity and swelling tests for observation of their performance in water and organic solvents. Then, the sample was treated with a 10% sodium carbonate solution and with ammonium quaternary, washed several times with distilled water, dried at 60°C, and characterized by XRD and swelling assays. Our results show that the clay was organophiilized and its ability to swell in organic solvents has increased.IntroductionThe kaolin clay, also known as ""china clay"" is chemically a hydrated aluminum silicate characterized as a very fine powder and lamellar structure (1:1), being constituted mainly by kaolinite [l]. Kaolin is a mineral extremely used as raw material. Its properties such as color, softness, small particle size and chemical inertness make it a suitable material for several industrial applications. The desired properties of kaolin varies widely for each application, beginning with its largest use in the paper industry until minor uses in the sectors of cosmetics and pharmaceutics. These two last applications require purified kaolin with defined functionality [2]. To find improvements in the functionality of kaolin for specific applications is important for many industrial uses. Sometimes the way to find these improvements might be modification of the kaolin clay by treatment with a chemical substance as ammonium quaternary, causing surface modifications [3,4]. In this work is described the modification of a Brazilian kaolin sample by treatment with cetyl trimethylammonium chloride (CTAC). The properties of the modified kaolin are being assessed by characterization and essays to understand its functionality and industrial application."

Jan 1, 2013

By Truan-Sheng Lui, Li-Hui Chen, Hao-Wen Hsueh, Fei-Yi Hung

"Since Ag wires have similar hardness and bonding properties to Au wires, they can be applied in some pads. In the present study, the annealing effect (at 225°C~275°C for 30min) on the tensile mechanical properties of silver wires with f=23µm was investigated. In addition, the micro-structural characteristics and the mechanical properties before and after an electric flame-off (EFO) process were also studied. Experimental results indicate that with annealing temperatures of more than 250°C, the silver wires possessed a fully annealed structure, the tensile strength and the hardness decreased, and the elongation was raised significantly. Under the thermal effect of EFO, the necks of the Ag balls underwent recrystallization and grain growth was induced, and the annealed Ag wires had a shorter zone of HAZ (220µm). The bonding strength and the neck-strength of the Ag wires were more than 7gf and possessed excellent bonding properties.IntroductionThermosonic ball bonding is one of the preferred processes for electronic packaging to connect a semiconductor chip and a lead frame by a thin metal wire. At present, gold wire and copper wire are the preferred interconnect materials to bond with the aluminum metallized wafer pads [1, 2]. Since gold is expensive and the reliability of copper is poorer [3], the study of silver wire has attracted a lot of attention already. In addition, the inherent properties of high ductility and low hardness of silver as well as its workability effectiveness compared to gold, have made it a preferred alternative .[4, 5]"

Jan 1, 2012

By Marcos Paulo Kohler Caldas, Jorge Alberto Soares Tenório, Mariana Alves de Carvalho, Denise Crocce Romano Espinosa

The massive application of electrical and electronic equipments increased the production and industry development, which leads to a rising envronmental and economic problem: the increase of e-waste’s generation. The main cause to explain this problem is the combination between the diversification of electric and electronic device’s applications and programmed obsolescence, which promotes a high generation the so-called waste electrical and electronic equipments (WEEE). Printed circuit boards (PCBs) are present in almost all WEEE and their heterogenous composition have a considerable amount of metals, including some preciousones. It is necessary to think about viable alternatives for the destination of WEEE, mostly PCBs’. Recycling is an environmental friendly purpose for PCBs’ destination, combined with economic advantage from the recovery of metals. The choice of correct process to recycling depends on the composition of the PCBs, so the correct characterization is required. This work aims to characterize two different PCBs from obsolete computers: motherboard and memory board, concluding that they have 35.5 and 18.92% of metals, respectively, including precious metals as silver and gold. Also, memory board has 0.122% of these precious metals to the detriment of 0.047% from motherboard. )

Mar 1, 2018

By Anastasia Alksnis

Pyrrhotite is an iron deficient, low nickel content sulfide mineral that is commonly associated with pentlandite, a nickel-rich sulfide; and are both main components of the nickel ore mined in Sudbury. Pyrrhotite tailings generated in the concentration of Ni ores are stored in tailing reservoirs and presents serious environmental risks including acid mine drainage. This study investigated the potential of converting pyrrhotite into a valuable resource through the use of fluidized bed roasting, in which the mineral will be oxidized to produce iron oxide and SO2 gas. These products can then be used to create iron for high-grade steel and elemental sulfur. Thermogravimetric analysis of Sudbury pyrrhotite was performed to study the oxidation kinetics, supporting the feasibility of this process. Further, energy and materials balance was carried out to establish the basic parameters of a possible roasting process.

By R. D. Pehlke

The history and present status of continuous casting of steel are reviewed, including a genera 1 description of current processes. Plant layout, process development and elements of machine component design are outlined, and key steps in integration into a stee-1 production system are detailed. Recent productivity advances and improvements in quality are described. Process developments are reviewed, and some future avenues for this technology are considered.

Jan 1, 1985